Merge remote-tracking branch 'regulator/topic/palmas' into regulator-next

Documentation/devicetree/bindings/regulator/palmas-pmic.txt

@@ -26,11 +26,17 @@ Optional nodes:
 
 	       For ti,palmas-pmic - smps12, smps123, smps3 depending on OTP,
 	       smps45, smps457, smps7 depending on variant, smps6, smps[8-9],
-	       smps10_out2, smps10_out1, do[1-9], ldoln, ldousb.
+	       smps10_out2, smps10_out1, ldo[1-9], ldoln, ldousb.
 
 	       Optional sub-node properties:
 	       ti,warm-reset - maintain voltage during warm reset(boolean)
-	       ti,roof-floor - control voltage selection by pin(boolean)
+	       ti,roof-floor - This takes as optional argument on platform supporting
+	       the rail from desired external control. If there is no argument then
+	       it will be assume that it is controlled by NSLEEP pin.
+	       The valid value for external pins are:
+			ENABLE1 then 1,
+			ENABLE2 then 2 or
+			NSLEEP then 3.
 	       ti,mode-sleep - mode to adopt in pmic sleep 0 - off, 1 - auto,
 	       2 - eco, 3 - forced pwm
 	       ti,smps-range - OTP has the wrong range set for the hardware so override
@@ -61,7 +67,7 @@ pmic {
 			regulator-always-on;
 			regulator-boot-on;
 			ti,warm-reset;
-			ti,roof-floor;
+			ti,roof-floor = <1>; /* ENABLE1 control */
 			ti,mode-sleep = <0>;
 			ti,smps-range = <1>;
 		};

drivers/regulator/palmas-regulator.c

@@ -33,6 +33,7 @@ struct regs_info {
 	u8	vsel_addr;
 	u8	ctrl_addr;
 	u8	tstep_addr;
+	int	sleep_id;
 };
 
 static const struct regs_info palmas_regs_info[] = {
@@ -42,6 +43,7 @@ static const struct regs_info palmas_regs_info[] = {
 		.vsel_addr	= PALMAS_SMPS12_VOLTAGE,
 		.ctrl_addr	= PALMAS_SMPS12_CTRL,
 		.tstep_addr	= PALMAS_SMPS12_TSTEP,
+		.sleep_id	= PALMAS_EXTERNAL_REQSTR_ID_SMPS12,
 	},
 	{
 		.name		= "SMPS123",
@@ -49,12 +51,14 @@ static const struct regs_info palmas_regs_info[] = {
 		.vsel_addr	= PALMAS_SMPS12_VOLTAGE,
 		.ctrl_addr	= PALMAS_SMPS12_CTRL,
 		.tstep_addr	= PALMAS_SMPS12_TSTEP,
+		.sleep_id	= PALMAS_EXTERNAL_REQSTR_ID_SMPS12,
 	},
 	{
 		.name		= "SMPS3",
 		.sname		= "smps3-in",
 		.vsel_addr	= PALMAS_SMPS3_VOLTAGE,
 		.ctrl_addr	= PALMAS_SMPS3_CTRL,
+		.sleep_id	= PALMAS_EXTERNAL_REQSTR_ID_SMPS3,
 	},
 	{
 		.name		= "SMPS45",
@@ -62,6 +66,7 @@ static const struct regs_info palmas_regs_info[] = {
 		.vsel_addr	= PALMAS_SMPS45_VOLTAGE,
 		.ctrl_addr	= PALMAS_SMPS45_CTRL,
 		.tstep_addr	= PALMAS_SMPS45_TSTEP,
+		.sleep_id	= PALMAS_EXTERNAL_REQSTR_ID_SMPS45,
 	},
 	{
 		.name		= "SMPS457",
@@ -69,6 +74,7 @@ static const struct regs_info palmas_regs_info[] = {
 		.vsel_addr	= PALMAS_SMPS45_VOLTAGE,
 		.ctrl_addr	= PALMAS_SMPS45_CTRL,
 		.tstep_addr	= PALMAS_SMPS45_TSTEP,
+		.sleep_id	= PALMAS_EXTERNAL_REQSTR_ID_SMPS45,
 	},
 	{
 		.name		= "SMPS6",
@@ -76,12 +82,14 @@ static const struct regs_info palmas_regs_info[] = {
 		.vsel_addr	= PALMAS_SMPS6_VOLTAGE,
 		.ctrl_addr	= PALMAS_SMPS6_CTRL,
 		.tstep_addr	= PALMAS_SMPS6_TSTEP,
+		.sleep_id	= PALMAS_EXTERNAL_REQSTR_ID_SMPS6,
 	},
 	{
 		.name		= "SMPS7",
 		.sname		= "smps7-in",
 		.vsel_addr	= PALMAS_SMPS7_VOLTAGE,
 		.ctrl_addr	= PALMAS_SMPS7_CTRL,
+		.sleep_id	= PALMAS_EXTERNAL_REQSTR_ID_SMPS7,
 	},
 	{
 		.name		= "SMPS8",
@@ -89,108 +97,128 @@ static const struct regs_info palmas_regs_info[] = {
 		.vsel_addr	= PALMAS_SMPS8_VOLTAGE,
 		.ctrl_addr	= PALMAS_SMPS8_CTRL,
 		.tstep_addr	= PALMAS_SMPS8_TSTEP,
+		.sleep_id	= PALMAS_EXTERNAL_REQSTR_ID_SMPS8,
 	},
 	{
 		.name		= "SMPS9",
 		.sname		= "smps9-in",
 		.vsel_addr	= PALMAS_SMPS9_VOLTAGE,
 		.ctrl_addr	= PALMAS_SMPS9_CTRL,
+		.sleep_id	= PALMAS_EXTERNAL_REQSTR_ID_SMPS9,
 	},
 	{
 		.name		= "SMPS10_OUT2",
 		.sname		= "smps10-in",
 		.ctrl_addr	= PALMAS_SMPS10_CTRL,
+		.sleep_id	= PALMAS_EXTERNAL_REQSTR_ID_SMPS10,
 	},
 	{
 		.name		= "SMPS10_OUT1",
 		.sname		= "smps10-out2",
 		.ctrl_addr	= PALMAS_SMPS10_CTRL,
+		.sleep_id	= PALMAS_EXTERNAL_REQSTR_ID_SMPS10,
 	},
 	{
 		.name		= "LDO1",
 		.sname		= "ldo1-in",
 		.vsel_addr	= PALMAS_LDO1_VOLTAGE,
 		.ctrl_addr	= PALMAS_LDO1_CTRL,
+		.sleep_id	= PALMAS_EXTERNAL_REQSTR_ID_LDO1,
 	},
 	{
 		.name		= "LDO2",
 		.sname		= "ldo2-in",
 		.vsel_addr	= PALMAS_LDO2_VOLTAGE,
 		.ctrl_addr	= PALMAS_LDO2_CTRL,
+		.sleep_id	= PALMAS_EXTERNAL_REQSTR_ID_LDO2,
 	},
 	{
 		.name		= "LDO3",
 		.sname		= "ldo3-in",
 		.vsel_addr	= PALMAS_LDO3_VOLTAGE,
 		.ctrl_addr	= PALMAS_LDO3_CTRL,
+		.sleep_id	= PALMAS_EXTERNAL_REQSTR_ID_LDO3,
 	},
 	{
 		.name		= "LDO4",
 		.sname		= "ldo4-in",
 		.vsel_addr	= PALMAS_LDO4_VOLTAGE,
 		.ctrl_addr	= PALMAS_LDO4_CTRL,
+		.sleep_id	= PALMAS_EXTERNAL_REQSTR_ID_LDO4,
 	},
 	{
 		.name		= "LDO5",
 		.sname		= "ldo5-in",
 		.vsel_addr	= PALMAS_LDO5_VOLTAGE,
 		.ctrl_addr	= PALMAS_LDO5_CTRL,
+		.sleep_id	= PALMAS_EXTERNAL_REQSTR_ID_LDO5,
 	},
 	{
 		.name		= "LDO6",
 		.sname		= "ldo6-in",
 		.vsel_addr	= PALMAS_LDO6_VOLTAGE,
 		.ctrl_addr	= PALMAS_LDO6_CTRL,
+		.sleep_id	= PALMAS_EXTERNAL_REQSTR_ID_LDO6,
 	},
 	{
 		.name		= "LDO7",
 		.sname		= "ldo7-in",
 		.vsel_addr	= PALMAS_LDO7_VOLTAGE,
 		.ctrl_addr	= PALMAS_LDO7_CTRL,
+		.sleep_id	= PALMAS_EXTERNAL_REQSTR_ID_LDO7,
 	},
 	{
 		.name		= "LDO8",
 		.sname		= "ldo8-in",
 		.vsel_addr	= PALMAS_LDO8_VOLTAGE,
 		.ctrl_addr	= PALMAS_LDO8_CTRL,
+		.sleep_id	= PALMAS_EXTERNAL_REQSTR_ID_LDO8,
 	},
 	{
 		.name		= "LDO9",
 		.sname		= "ldo9-in",
 		.vsel_addr	= PALMAS_LDO9_VOLTAGE,
 		.ctrl_addr	= PALMAS_LDO9_CTRL,
+		.sleep_id	= PALMAS_EXTERNAL_REQSTR_ID_LDO9,
 	},
 	{
 		.name		= "LDOLN",
 		.sname		= "ldoln-in",
 		.vsel_addr	= PALMAS_LDOLN_VOLTAGE,
 		.ctrl_addr	= PALMAS_LDOLN_CTRL,
+		.sleep_id	= PALMAS_EXTERNAL_REQSTR_ID_LDOLN,
 	},
 	{
 		.name		= "LDOUSB",
 		.sname		= "ldousb-in",
 		.vsel_addr	= PALMAS_LDOUSB_VOLTAGE,
 		.ctrl_addr	= PALMAS_LDOUSB_CTRL,
+		.sleep_id	= PALMAS_EXTERNAL_REQSTR_ID_LDOUSB,
 	},
 	{
 		.name		= "REGEN1",
 		.ctrl_addr	= PALMAS_REGEN1_CTRL,
+		.sleep_id	= PALMAS_EXTERNAL_REQSTR_ID_REGEN1,
 	},
 	{
 		.name		= "REGEN2",
 		.ctrl_addr	= PALMAS_REGEN2_CTRL,
+		.sleep_id	= PALMAS_EXTERNAL_REQSTR_ID_REGEN2,
 	},
 	{
 		.name		= "REGEN3",
 		.ctrl_addr	= PALMAS_REGEN3_CTRL,
+		.sleep_id	= PALMAS_EXTERNAL_REQSTR_ID_REGEN3,
 	},
 	{
 		.name		= "SYSEN1",
 		.ctrl_addr	= PALMAS_SYSEN1_CTRL,
+		.sleep_id	= PALMAS_EXTERNAL_REQSTR_ID_SYSEN1,
 	},
 	{
 		.name		= "SYSEN2",
 		.ctrl_addr	= PALMAS_SYSEN2_CTRL,
+		.sleep_id	= PALMAS_EXTERNAL_REQSTR_ID_SYSEN2,
 	},
 };
 
@@ -478,6 +506,17 @@ static struct regulator_ops palmas_ops_smps = {
 	.set_ramp_delay		= palmas_smps_set_ramp_delay,
 };
 
+static struct regulator_ops palmas_ops_ext_control_smps = {
+	.set_mode		= palmas_set_mode_smps,
+	.get_mode		= palmas_get_mode_smps,
+	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
+	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
+	.list_voltage		= palmas_list_voltage_smps,
+	.map_voltage		= palmas_map_voltage_smps,
+	.set_voltage_time_sel	= palma_smps_set_voltage_smps_time_sel,
+	.set_ramp_delay		= palmas_smps_set_ramp_delay,
+};
+
 static struct regulator_ops palmas_ops_smps10 = {
 	.is_enabled		= regulator_is_enabled_regmap,
 	.enable			= regulator_enable_regmap,
@@ -513,12 +552,37 @@ static struct regulator_ops palmas_ops_ldo = {
 	.map_voltage		= regulator_map_voltage_linear,
 };
 
+static struct regulator_ops palmas_ops_ext_control_ldo = {
+	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
+	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
+	.list_voltage		= regulator_list_voltage_linear,
+	.map_voltage		= regulator_map_voltage_linear,
+};
+
 static struct regulator_ops palmas_ops_extreg = {
 	.is_enabled		= regulator_is_enabled_regmap,
 	.enable			= regulator_enable_regmap,
 	.disable		= regulator_disable_regmap,
 };
 
+static struct regulator_ops palmas_ops_ext_control_extreg = {
+};
+
+static int palmas_regulator_config_external(struct palmas *palmas, int id,
+		struct palmas_reg_init *reg_init)
+{
+	int sleep_id = palmas_regs_info[id].sleep_id;
+	int ret;
+
+	ret = palmas_ext_control_req_config(palmas, sleep_id,
+					reg_init->roof_floor, true);
+	if (ret < 0)
+		dev_err(palmas->dev,
+			"Ext control config for regulator %d failed %d\n",
+			id, ret);
+	return ret;
+}
+
 /*
  * setup the hardware based sleep configuration of the SMPS/LDO regulators
  * from the platform data. This is different to the software based control
@@ -577,7 +641,22 @@ static int palmas_smps_init(struct palmas *palmas, int id,
 			return ret;
 	}
 
+	if (reg_init->roof_floor && (id != PALMAS_REG_SMPS10_OUT1) &&
+			(id != PALMAS_REG_SMPS10_OUT2)) {
+		/* Enable externally controlled regulator */
+		addr = palmas_regs_info[id].ctrl_addr;
+		ret = palmas_smps_read(palmas, addr, &reg);
+		if (ret < 0)
+			return ret;
 
+		if (!(reg & PALMAS_SMPS12_CTRL_MODE_ACTIVE_MASK)) {
+			reg |= SMPS_CTRL_MODE_ON;
+			ret = palmas_smps_write(palmas, addr, reg);
+			if (ret < 0)
+				return ret;
+		}
+		return palmas_regulator_config_external(palmas, id, reg_init);
+	}
 	return 0;
 }
 
@@ -608,6 +687,20 @@ static int palmas_ldo_init(struct palmas *palmas, int id,
 	if (ret)
 		return ret;
 
+	if (reg_init->roof_floor) {
+		/* Enable externally controlled regulator */
+		addr = palmas_regs_info[id].ctrl_addr;
+		ret = palmas_update_bits(palmas, PALMAS_LDO_BASE,
+				addr, PALMAS_LDO1_CTRL_MODE_ACTIVE,
+				PALMAS_LDO1_CTRL_MODE_ACTIVE);
+		if (ret < 0) {
+			dev_err(palmas->dev,
+				"LDO Register 0x%02x update failed %d\n",
+				addr, ret);
+			return ret;
+		}
+		return palmas_regulator_config_external(palmas, id, reg_init);
+	}
 	return 0;
 }
 
@@ -630,6 +723,21 @@ static int palmas_extreg_init(struct palmas *palmas, int id,
 			addr, ret);
 		return ret;
 	}
+
+	if (reg_init->roof_floor) {
+		/* Enable externally controlled regulator */
+		addr = palmas_regs_info[id].ctrl_addr;
+		ret = palmas_update_bits(palmas, PALMAS_RESOURCE_BASE,
+				addr, PALMAS_REGEN1_CTRL_MODE_ACTIVE,
+				PALMAS_REGEN1_CTRL_MODE_ACTIVE);
+		if (ret < 0) {
+			dev_err(palmas->dev,
+				"Resource Register 0x%02x update failed %d\n",
+				addr, ret);
+			return ret;
+		}
+		return palmas_regulator_config_external(palmas, id, reg_init);
+	}
 	return 0;
 }
 
@@ -712,7 +820,7 @@ static void palmas_dt_to_pdata(struct device *dev,
 	int idx, ret;
 
 	node = of_node_get(node);
-	regulators = of_find_node_by_name(node, "regulators");
+	regulators = of_get_child_by_name(node, "regulators");
 	if (!regulators) {
 		dev_info(dev, "regulator node not found\n");
 		return;
@@ -740,9 +848,35 @@ static void palmas_dt_to_pdata(struct device *dev,
 			of_property_read_bool(palmas_matches[idx].of_node,
 					     "ti,warm-reset");
 
-		pdata->reg_init[idx]->roof_floor =
+		ret = of_property_read_u32(palmas_matches[idx].of_node,
-			of_property_read_bool(palmas_matches[idx].of_node,
+					      "ti,roof-floor", &prop);
-					      "ti,roof-floor");
+		/* EINVAL: Property not found */
+		if (ret != -EINVAL) {
+			int econtrol;
+
+			/* use default value, when no value is specified */
+			econtrol = PALMAS_EXT_CONTROL_NSLEEP;
+			if (!ret) {
+				switch (prop) {
+				case 1:
+					econtrol = PALMAS_EXT_CONTROL_ENABLE1;
+					break;
+				case 2:
+					econtrol = PALMAS_EXT_CONTROL_ENABLE2;
+					break;
+				case 3:
+					econtrol = PALMAS_EXT_CONTROL_NSLEEP;
+					break;
+				default:
+					WARN_ON(1);
+					dev_warn(dev,
+					"%s: Invalid roof-floor option: %u\n",
+					     palmas_matches[idx].name, prop);
+					break;
+				}
+			}
+			pdata->reg_init[idx]->roof_floor = econtrol;
+		}
 
 		ret = of_property_read_u32(palmas_matches[idx].of_node,
 				"ti,mode-sleep", &prop);
@@ -869,6 +1003,8 @@ static int palmas_regulators_probe(struct platform_device *pdev)
 			ret = palmas_smps_init(palmas, id, reg_init);
 			if (ret)
 				return ret;
+		} else {
+			reg_init = NULL;
 		}
 
 		/* Register the regulators */
@@ -913,7 +1049,11 @@ static int palmas_regulators_probe(struct platform_device *pdev)
 			if (reg & PALMAS_SMPS12_VOLTAGE_RANGE)
 				pmic->range[id] = 1;
 
-			pmic->desc[id].ops = &palmas_ops_smps;
+			if (reg_init && reg_init->roof_floor)
+				pmic->desc[id].ops =
+						&palmas_ops_ext_control_smps;
+			else
+				pmic->desc[id].ops = &palmas_ops_smps;
 			pmic->desc[id].n_voltages = PALMAS_SMPS_NUM_VOLTAGES;
 			pmic->desc[id].vsel_reg =
 					PALMAS_BASE_TO_REG(PALMAS_SMPS_BASE,
@@ -956,6 +1096,10 @@ static int palmas_regulators_probe(struct platform_device *pdev)
 
 	/* Start this loop from the id left from previous loop */
 	for (; id < PALMAS_NUM_REGS; id++) {
+		if (pdata && pdata->reg_init[id])
+			reg_init = pdata->reg_init[id];
+		else
+			reg_init = NULL;
 
 		/* Miss out regulators which are not available due
 		 * to alternate functions.
@@ -969,7 +1113,11 @@ static int palmas_regulators_probe(struct platform_device *pdev)
 
 		if (id < PALMAS_REG_REGEN1) {
 			pmic->desc[id].n_voltages = PALMAS_LDO_NUM_VOLTAGES;
-			pmic->desc[id].ops = &palmas_ops_ldo;
+			if (reg_init && reg_init->roof_floor)
+				pmic->desc[id].ops =
+					&palmas_ops_ext_control_ldo;
+			else
+				pmic->desc[id].ops = &palmas_ops_ldo;
 			pmic->desc[id].min_uV = 900000;
 			pmic->desc[id].uV_step = 50000;
 			pmic->desc[id].linear_min_sel = 1;
@@ -999,7 +1147,11 @@ static int palmas_regulators_probe(struct platform_device *pdev)
 				pmic->desc[id].enable_time = 2000;
 		} else {
 			pmic->desc[id].n_voltages = 1;
-			pmic->desc[id].ops = &palmas_ops_extreg;
+			if (reg_init && reg_init->roof_floor)
+				pmic->desc[id].ops =
+					&palmas_ops_ext_control_extreg;
+			else
+				pmic->desc[id].ops = &palmas_ops_extreg;
 			pmic->desc[id].enable_reg =
 					PALMAS_BASE_TO_REG(PALMAS_RESOURCE_BASE,
 						palmas_regs_info[id].ctrl_addr);