diff --git a/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c b/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
index 069d167ab410..1a3727aa28a8 100644
--- a/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
+++ b/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
@@ -1,5 +1,5 @@
 /*
- * Copyright (c) 2012-2014, 2016 The Linux Foundation. All rights reserved.
+ * Copyright (c) 2012-2014, 2016, 2018 The Linux Foundation. All rights reserved.
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 and
@@ -538,7 +538,7 @@ static int pmic_gpio_config_set(struct pinctrl_dev *pctldev, unsigned int pin,
 			pad->pullup = arg;
 			break;
 		case PMIC_GPIO_CONF_STRENGTH:
-			if (arg > PMIC_GPIO_STRENGTH_LOW)
+			if (arg > PMIC_GPIO_STRENGTH_HIGH)
 				return -EINVAL;
 			pad->strength = arg;
 			break;
diff --git a/drivers/pinctrl/qcom/pinctrl-ssbi-gpio.c b/drivers/pinctrl/qcom/pinctrl-ssbi-gpio.c
index ae351167d849..5645b38d6132 100644
--- a/drivers/pinctrl/qcom/pinctrl-ssbi-gpio.c
+++ b/drivers/pinctrl/qcom/pinctrl-ssbi-gpio.c
@@ -1,6 +1,6 @@
 /*
  * Copyright (c) 2015, Sony Mobile Communications AB.
- * Copyright (c) 2013, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2013, 2018 The Linux Foundation. All rights reserved.
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 and
@@ -379,7 +379,7 @@ static int pm8xxx_pin_config_set(struct pinctrl_dev *pctldev,
 			banks |= BIT(0);
 			break;
 		case PM8XXX_QCOM_DRIVE_STRENGH:
-			if (arg > PMIC_GPIO_STRENGTH_LOW) {
+			if (arg > PM8921_GPIO_STRENGTH_LOW) {
 				dev_err(pctrl->dev, "invalid drive strength\n");
 				return -EINVAL;
 			}
diff --git a/include/dt-bindings/pinctrl/qcom,pmic-gpio.h b/include/dt-bindings/pinctrl/qcom,pmic-gpio.h
index 64e2dc7183f3..7ac6f1631098 100644
--- a/include/dt-bindings/pinctrl/qcom,pmic-gpio.h
+++ b/include/dt-bindings/pinctrl/qcom,pmic-gpio.h
@@ -11,9 +11,14 @@
 #define PMIC_GPIO_PULL_UP_1P5_30	3
 
 #define PMIC_GPIO_STRENGTH_NO		0
-#define PMIC_GPIO_STRENGTH_HIGH		1
+#define PMIC_GPIO_STRENGTH_LOW		1
 #define PMIC_GPIO_STRENGTH_MED		2
-#define PMIC_GPIO_STRENGTH_LOW		3
+#define PMIC_GPIO_STRENGTH_HIGH		3
+
+#define PM8921_GPIO_STRENGTH_NO		0
+#define PM8921_GPIO_STRENGTH_HIGH	1
+#define PM8921_GPIO_STRENGTH_MED	2
+#define PM8921_GPIO_STRENGTH_LOW	3
 
 /*
  * Note: PM8018 GPIO3 and GPIO4 are supporting