[ARM] S3C2440: Merge branch next-mini2440 into next-s3c
Merge branch 'next-mini2440' into next-s3c
This commit is contained in:
Ben Dooks
commit
9f01efaa49
5 changed files with 2832 additions and 0 deletions
|
|
@ -1358,6 +1358,27 @@ and is between 256 and 4096 characters. It is defined in the file
|
||||||
min_addr=nn[KMG] [KNL,BOOT,ia64] All physical memory below this
|
min_addr=nn[KMG] [KNL,BOOT,ia64] All physical memory below this
|
||||||
physical address is ignored.
|
physical address is ignored.
|
||||||
|
|
||||||
|
mini2440= [ARM,HW,KNL]
|
||||||
|
Format:[0..2][b][c][t]
|
||||||
|
Default: "0tb"
|
||||||
|
MINI2440 configuration specification:
|
||||||
|
0 - The attached screen is the 3.5" TFT
|
||||||
|
1 - The attached screen is the 7" TFT
|
||||||
|
2 - The VGA Shield is attached (1024x768)
|
||||||
|
Leaving out the screen size parameter will not load
|
||||||
|
the TFT driver, and the framebuffer will be left
|
||||||
|
unconfigured.
|
||||||
|
b - Enable backlight. The TFT backlight pin will be
|
||||||
|
linked to the kernel VESA blanking code and a GPIO
|
||||||
|
LED. This parameter is not necessary when using the
|
||||||
|
VGA shield.
|
||||||
|
c - Enable the s3c camera interface.
|
||||||
|
t - Reserved for enabling touchscreen support. The
|
||||||
|
touchscreen support is not enabled in the mainstream
|
||||||
|
kernel as of 2.6.30, a preliminary port can be found
|
||||||
|
in the "bleeding edge" mini2440 support kernel at
|
||||||
|
http://repo.or.cz/w/linux-2.6/mini2440.git
|
||||||
|
|
||||||
mminit_loglevel=
|
mminit_loglevel=
|
||||||
[KNL] When CONFIG_DEBUG_MEMORY_INIT is set, this
|
[KNL] When CONFIG_DEBUG_MEMORY_INIT is set, this
|
||||||
parameter allows control of the logging verbosity for
|
parameter allows control of the logging verbosity for
|
||||||
|
|
|
||||||
2097
arch/arm/configs/mini2440_defconfig
Normal file
2097
arch/arm/configs/mini2440_defconfig
Normal file
File diff suppressed because it is too large
Load diff
|
|
@ -84,5 +84,15 @@ config MACH_AT2440EVB
|
||||||
help
|
help
|
||||||
Say Y here if you are using the AT2440EVB development board
|
Say Y here if you are using the AT2440EVB development board
|
||||||
|
|
||||||
|
config MACH_MINI2440
|
||||||
|
bool "MINI2440 development board"
|
||||||
|
select CPU_S3C2440
|
||||||
|
select EEPROM_AT24
|
||||||
|
select LEDS_TRIGGER_BACKLIGHT
|
||||||
|
select SND_S3C24XX_SOC_S3C24XX_UDA134X
|
||||||
|
help
|
||||||
|
Say Y here to select support for the MINI2440. Is a 10cm x 10cm board
|
||||||
|
available via various sources. It can come with a 3.5" or 7" touch LCD.
|
||||||
|
|
||||||
endmenu
|
endmenu
|
||||||
|
|
||||||
|
|
|
||||||
|
|
@ -22,3 +22,4 @@ obj-$(CONFIG_MACH_RX3715) += mach-rx3715.o
|
||||||
obj-$(CONFIG_ARCH_S3C2440) += mach-smdk2440.o
|
obj-$(CONFIG_ARCH_S3C2440) += mach-smdk2440.o
|
||||||
obj-$(CONFIG_MACH_NEXCODER_2440) += mach-nexcoder.o
|
obj-$(CONFIG_MACH_NEXCODER_2440) += mach-nexcoder.o
|
||||||
obj-$(CONFIG_MACH_AT2440EVB) += mach-at2440evb.o
|
obj-$(CONFIG_MACH_AT2440EVB) += mach-at2440evb.o
|
||||||
|
obj-$(CONFIG_MACH_MINI2440) += mach-mini2440.o
|
||||||
|
|
|
||||||
703
arch/arm/mach-s3c2440/mach-mini2440.c
Normal file
703
arch/arm/mach-s3c2440/mach-mini2440.c
Normal file
|
|
@ -0,0 +1,703 @@
|
||||||
|
/* linux/arch/arm/mach-s3c2440/mach-mini2440.c
|
||||||
|
*
|
||||||
|
* Copyright (c) 2008 Ramax Lo <ramaxlo@gmail.com>
|
||||||
|
* Based on mach-anubis.c by Ben Dooks <ben@simtec.co.uk>
|
||||||
|
* and modifications by SBZ <sbz@spgui.org> and
|
||||||
|
* Weibing <http://weibing.blogbus.com> and
|
||||||
|
* Michel Pollet <buserror@gmail.com>
|
||||||
|
*
|
||||||
|
* For product information, visit http://code.google.com/p/mini2440/
|
||||||
|
*
|
||||||
|
* This program is free software; you can redistribute it and/or modify
|
||||||
|
* it under the terms of the GNU General Public License version 2 as
|
||||||
|
* published by the Free Software Foundation.
|
||||||
|
*/
|
||||||
|
|
||||||
|
#include <linux/kernel.h>
|
||||||
|
#include <linux/types.h>
|
||||||
|
#include <linux/interrupt.h>
|
||||||
|
#include <linux/list.h>
|
||||||
|
#include <linux/timer.h>
|
||||||
|
#include <linux/init.h>
|
||||||
|
#include <linux/gpio.h>
|
||||||
|
#include <linux/input.h>
|
||||||
|
#include <linux/io.h>
|
||||||
|
#include <linux/serial_core.h>
|
||||||
|
#include <linux/dm9000.h>
|
||||||
|
#include <linux/i2c/at24.h>
|
||||||
|
#include <linux/platform_device.h>
|
||||||
|
#include <linux/gpio_keys.h>
|
||||||
|
#include <linux/i2c.h>
|
||||||
|
#include <linux/mmc/host.h>
|
||||||
|
|
||||||
|
#include <asm/mach/arch.h>
|
||||||
|
#include <asm/mach/map.h>
|
||||||
|
|
||||||
|
#include <mach/hardware.h>
|
||||||
|
#include <mach/fb.h>
|
||||||
|
#include <asm/mach-types.h>
|
||||||
|
|
||||||
|
#include <plat/regs-serial.h>
|
||||||
|
#include <mach/regs-gpio.h>
|
||||||
|
#include <mach/leds-gpio.h>
|
||||||
|
#include <mach/regs-mem.h>
|
||||||
|
#include <mach/regs-lcd.h>
|
||||||
|
#include <mach/irqs.h>
|
||||||
|
#include <plat/nand.h>
|
||||||
|
#include <plat/iic.h>
|
||||||
|
#include <plat/mci.h>
|
||||||
|
#include <plat/udc.h>
|
||||||
|
|
||||||
|
#include <plat/regs-serial.h>
|
||||||
|
|
||||||
|
#include <linux/mtd/mtd.h>
|
||||||
|
#include <linux/mtd/nand.h>
|
||||||
|
#include <linux/mtd/nand_ecc.h>
|
||||||
|
#include <linux/mtd/partitions.h>
|
||||||
|
|
||||||
|
#include <plat/clock.h>
|
||||||
|
#include <plat/devs.h>
|
||||||
|
#include <plat/cpu.h>
|
||||||
|
|
||||||
|
#include <sound/s3c24xx_uda134x.h>
|
||||||
|
|
||||||
|
#define MACH_MINI2440_DM9K_BASE (S3C2410_CS4 + 0x300)
|
||||||
|
|
||||||
|
static struct map_desc mini2440_iodesc[] __initdata = {
|
||||||
|
/* nothing to declare, move along */
|
||||||
|
};
|
||||||
|
|
||||||
|
#define UCON S3C2410_UCON_DEFAULT
|
||||||
|
#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB
|
||||||
|
#define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE
|
||||||
|
|
||||||
|
|
||||||
|
static struct s3c2410_uartcfg mini2440_uartcfgs[] __initdata = {
|
||||||
|
[0] = {
|
||||||
|
.hwport = 0,
|
||||||
|
.flags = 0,
|
||||||
|
.ucon = UCON,
|
||||||
|
.ulcon = ULCON,
|
||||||
|
.ufcon = UFCON,
|
||||||
|
},
|
||||||
|
[1] = {
|
||||||
|
.hwport = 1,
|
||||||
|
.flags = 0,
|
||||||
|
.ucon = UCON,
|
||||||
|
.ulcon = ULCON,
|
||||||
|
.ufcon = UFCON,
|
||||||
|
},
|
||||||
|
[2] = {
|
||||||
|
.hwport = 2,
|
||||||
|
.flags = 0,
|
||||||
|
.ucon = UCON,
|
||||||
|
.ulcon = ULCON,
|
||||||
|
.ufcon = UFCON,
|
||||||
|
},
|
||||||
|
};
|
||||||
|
|
||||||
|
/* USB device UDC support */
|
||||||
|
|
||||||
|
static void mini2440_udc_pullup(enum s3c2410_udc_cmd_e cmd)
|
||||||
|
{
|
||||||
|
pr_debug("udc: pullup(%d)\n", cmd);
|
||||||
|
|
||||||
|
switch (cmd) {
|
||||||
|
case S3C2410_UDC_P_ENABLE :
|
||||||
|
s3c2410_gpio_setpin(S3C2410_GPC(5), 1);
|
||||||
|
break;
|
||||||
|
case S3C2410_UDC_P_DISABLE :
|
||||||
|
s3c2410_gpio_setpin(S3C2410_GPC(5), 0);
|
||||||
|
break;
|
||||||
|
case S3C2410_UDC_P_RESET :
|
||||||
|
break;
|
||||||
|
default:
|
||||||
|
break;
|
||||||
|
}
|
||||||
|
}
|
||||||
|
|
||||||
|
static struct s3c2410_udc_mach_info mini2440_udc_cfg __initdata = {
|
||||||
|
.udc_command = mini2440_udc_pullup,
|
||||||
|
};
|
||||||
|
|
||||||
|
|
||||||
|
/* LCD timing and setup */
|
||||||
|
|
||||||
|
/*
|
||||||
|
* This macro simplifies the table bellow
|
||||||
|
*/
|
||||||
|
#define _LCD_DECLARE(_clock,_xres,margin_left,margin_right,hsync, \
|
||||||
|
_yres,margin_top,margin_bottom,vsync, refresh) \
|
||||||
|
.width = _xres, \
|
||||||
|
.xres = _xres, \
|
||||||
|
.height = _yres, \
|
||||||
|
.yres = _yres, \
|
||||||
|
.left_margin = margin_left, \
|
||||||
|
.right_margin = margin_right, \
|
||||||
|
.upper_margin = margin_top, \
|
||||||
|
.lower_margin = margin_bottom, \
|
||||||
|
.hsync_len = hsync, \
|
||||||
|
.vsync_len = vsync, \
|
||||||
|
.pixclock = ((_clock*100000000000LL) / \
|
||||||
|
((refresh) * \
|
||||||
|
(hsync + margin_left + _xres + margin_right) * \
|
||||||
|
(vsync + margin_top + _yres + margin_bottom))), \
|
||||||
|
.bpp = 16,\
|
||||||
|
.type = (S3C2410_LCDCON1_TFT16BPP |\
|
||||||
|
S3C2410_LCDCON1_TFT)
|
||||||
|
|
||||||
|
struct s3c2410fb_display mini2440_lcd_cfg[] __initdata = {
|
||||||
|
[0] = { /* mini2440 + 3.5" TFT + touchscreen */
|
||||||
|
_LCD_DECLARE(
|
||||||
|
7, /* The 3.5 is quite fast */
|
||||||
|
240, 21, 38, 6, /* x timing */
|
||||||
|
320, 4, 4, 2, /* y timing */
|
||||||
|
60), /* refresh rate */
|
||||||
|
.lcdcon5 = (S3C2410_LCDCON5_FRM565 |
|
||||||
|
S3C2410_LCDCON5_INVVLINE |
|
||||||
|
S3C2410_LCDCON5_INVVFRAME |
|
||||||
|
S3C2410_LCDCON5_INVVDEN |
|
||||||
|
S3C2410_LCDCON5_PWREN),
|
||||||
|
},
|
||||||
|
[1] = { /* mini2440 + 7" TFT + touchscreen */
|
||||||
|
_LCD_DECLARE(
|
||||||
|
10, /* the 7" runs slower */
|
||||||
|
800, 40, 40, 48, /* x timing */
|
||||||
|
480, 29, 3, 3, /* y timing */
|
||||||
|
50), /* refresh rate */
|
||||||
|
.lcdcon5 = (S3C2410_LCDCON5_FRM565 |
|
||||||
|
S3C2410_LCDCON5_INVVLINE |
|
||||||
|
S3C2410_LCDCON5_INVVFRAME |
|
||||||
|
S3C2410_LCDCON5_PWREN),
|
||||||
|
},
|
||||||
|
/* The VGA shield can outout at several resolutions. All share
|
||||||
|
* the same timings, however, anything smaller than 1024x768
|
||||||
|
* will only be displayed in the top left corner of a 1024x768
|
||||||
|
* XGA output unless you add optional dip switches to the shield.
|
||||||
|
* Therefore timings for other resolutions have been ommited here.
|
||||||
|
*/
|
||||||
|
[2] = {
|
||||||
|
_LCD_DECLARE(
|
||||||
|
10,
|
||||||
|
1024, 1, 2, 2, /* y timing */
|
||||||
|
768, 200, 16, 16, /* x timing */
|
||||||
|
24), /* refresh rate, maximum stable,
|
||||||
|
tested with the FPGA shield */
|
||||||
|
.lcdcon5 = (S3C2410_LCDCON5_FRM565 |
|
||||||
|
S3C2410_LCDCON5_HWSWP),
|
||||||
|
},
|
||||||
|
};
|
||||||
|
|
||||||
|
/* todo - put into gpio header */
|
||||||
|
|
||||||
|
#define S3C2410_GPCCON_MASK(x) (3 << ((x) * 2))
|
||||||
|
#define S3C2410_GPDCON_MASK(x) (3 << ((x) * 2))
|
||||||
|
|
||||||
|
struct s3c2410fb_mach_info mini2440_fb_info __initdata = {
|
||||||
|
.displays = &mini2440_lcd_cfg[0], /* not constant! see init */
|
||||||
|
.num_displays = 1,
|
||||||
|
.default_display = 0,
|
||||||
|
|
||||||
|
/* Enable VD[2..7], VD[10..15], VD[18..23] and VCLK, syncs, VDEN
|
||||||
|
* and disable the pull down resistors on pins we are using for LCD
|
||||||
|
* data. */
|
||||||
|
|
||||||
|
.gpcup = (0xf << 1) | (0x3f << 10),
|
||||||
|
|
||||||
|
.gpccon = (S3C2410_GPC1_VCLK | S3C2410_GPC2_VLINE |
|
||||||
|
S3C2410_GPC3_VFRAME | S3C2410_GPC4_VM |
|
||||||
|
S3C2410_GPC10_VD2 | S3C2410_GPC11_VD3 |
|
||||||
|
S3C2410_GPC12_VD4 | S3C2410_GPC13_VD5 |
|
||||||
|
S3C2410_GPC14_VD6 | S3C2410_GPC15_VD7),
|
||||||
|
|
||||||
|
.gpccon_mask = (S3C2410_GPCCON_MASK(1) | S3C2410_GPCCON_MASK(2) |
|
||||||
|
S3C2410_GPCCON_MASK(3) | S3C2410_GPCCON_MASK(4) |
|
||||||
|
S3C2410_GPCCON_MASK(10) | S3C2410_GPCCON_MASK(11) |
|
||||||
|
S3C2410_GPCCON_MASK(12) | S3C2410_GPCCON_MASK(13) |
|
||||||
|
S3C2410_GPCCON_MASK(14) | S3C2410_GPCCON_MASK(15)),
|
||||||
|
|
||||||
|
.gpdup = (0x3f << 2) | (0x3f << 10),
|
||||||
|
|
||||||
|
.gpdcon = (S3C2410_GPD2_VD10 | S3C2410_GPD3_VD11 |
|
||||||
|
S3C2410_GPD4_VD12 | S3C2410_GPD5_VD13 |
|
||||||
|
S3C2410_GPD6_VD14 | S3C2410_GPD7_VD15 |
|
||||||
|
S3C2410_GPD10_VD18 | S3C2410_GPD11_VD19 |
|
||||||
|
S3C2410_GPD12_VD20 | S3C2410_GPD13_VD21 |
|
||||||
|
S3C2410_GPD14_VD22 | S3C2410_GPD15_VD23),
|
||||||
|
|
||||||
|
.gpdcon_mask = (S3C2410_GPDCON_MASK(2) | S3C2410_GPDCON_MASK(3) |
|
||||||
|
S3C2410_GPDCON_MASK(4) | S3C2410_GPDCON_MASK(5) |
|
||||||
|
S3C2410_GPDCON_MASK(6) | S3C2410_GPDCON_MASK(7) |
|
||||||
|
S3C2410_GPDCON_MASK(10) | S3C2410_GPDCON_MASK(11)|
|
||||||
|
S3C2410_GPDCON_MASK(12) | S3C2410_GPDCON_MASK(13)|
|
||||||
|
S3C2410_GPDCON_MASK(14) | S3C2410_GPDCON_MASK(15)),
|
||||||
|
};
|
||||||
|
|
||||||
|
/* MMC/SD */
|
||||||
|
|
||||||
|
static struct s3c24xx_mci_pdata mini2440_mmc_cfg __initdata = {
|
||||||
|
.gpio_detect = S3C2410_GPG(8),
|
||||||
|
.gpio_wprotect = S3C2410_GPH(8),
|
||||||
|
.set_power = NULL,
|
||||||
|
.ocr_avail = MMC_VDD_32_33|MMC_VDD_33_34,
|
||||||
|
};
|
||||||
|
|
||||||
|
/* NAND Flash on MINI2440 board */
|
||||||
|
|
||||||
|
static struct mtd_partition mini2440_default_nand_part[] __initdata = {
|
||||||
|
[0] = {
|
||||||
|
.name = "u-boot",
|
||||||
|
.size = SZ_256K,
|
||||||
|
.offset = 0,
|
||||||
|
},
|
||||||
|
[1] = {
|
||||||
|
.name = "u-boot-env",
|
||||||
|
.size = SZ_128K,
|
||||||
|
.offset = SZ_256K,
|
||||||
|
},
|
||||||
|
[2] = {
|
||||||
|
.name = "kernel",
|
||||||
|
/* 5 megabytes, for a kernel with no modules
|
||||||
|
* or a uImage with a ramdisk attached */
|
||||||
|
.size = 0x00500000,
|
||||||
|
.offset = SZ_256K + SZ_128K,
|
||||||
|
},
|
||||||
|
[3] = {
|
||||||
|
.name = "root",
|
||||||
|
.offset = SZ_256K + SZ_128K + 0x00500000,
|
||||||
|
.size = MTDPART_SIZ_FULL,
|
||||||
|
},
|
||||||
|
};
|
||||||
|
|
||||||
|
static struct s3c2410_nand_set mini2440_nand_sets[] __initdata = {
|
||||||
|
[0] = {
|
||||||
|
.name = "nand",
|
||||||
|
.nr_chips = 1,
|
||||||
|
.nr_partitions = ARRAY_SIZE(mini2440_default_nand_part),
|
||||||
|
.partitions = mini2440_default_nand_part,
|
||||||
|
},
|
||||||
|
};
|
||||||
|
|
||||||
|
static struct s3c2410_platform_nand mini2440_nand_info __initdata = {
|
||||||
|
.tacls = 0,
|
||||||
|
.twrph0 = 25,
|
||||||
|
.twrph1 = 15,
|
||||||
|
.nr_sets = ARRAY_SIZE(mini2440_nand_sets),
|
||||||
|
.sets = mini2440_nand_sets,
|
||||||
|
.ignore_unset_ecc = 1,
|
||||||
|
};
|
||||||
|
|
||||||
|
/* DM9000AEP 10/100 ethernet controller */
|
||||||
|
|
||||||
|
static struct resource mini2440_dm9k_resource[] __initdata = {
|
||||||
|
[0] = {
|
||||||
|
.start = MACH_MINI2440_DM9K_BASE,
|
||||||
|
.end = MACH_MINI2440_DM9K_BASE + 3,
|
||||||
|
.flags = IORESOURCE_MEM
|
||||||
|
},
|
||||||
|
[1] = {
|
||||||
|
.start = MACH_MINI2440_DM9K_BASE + 4,
|
||||||
|
.end = MACH_MINI2440_DM9K_BASE + 7,
|
||||||
|
.flags = IORESOURCE_MEM
|
||||||
|
},
|
||||||
|
[2] = {
|
||||||
|
.start = IRQ_EINT7,
|
||||||
|
.end = IRQ_EINT7,
|
||||||
|
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
|
||||||
|
}
|
||||||
|
};
|
||||||
|
|
||||||
|
/*
|
||||||
|
* The DM9000 has no eeprom, and it's MAC address is set by
|
||||||
|
* the bootloader before starting the kernel.
|
||||||
|
*/
|
||||||
|
static struct dm9000_plat_data mini2440_dm9k_pdata __initdata = {
|
||||||
|
.flags = (DM9000_PLATF_16BITONLY | DM9000_PLATF_NO_EEPROM),
|
||||||
|
};
|
||||||
|
|
||||||
|
static struct platform_device mini2440_device_eth __initdata = {
|
||||||
|
.name = "dm9000",
|
||||||
|
.id = -1,
|
||||||
|
.num_resources = ARRAY_SIZE(mini2440_dm9k_resource),
|
||||||
|
.resource = mini2440_dm9k_resource,
|
||||||
|
.dev = {
|
||||||
|
.platform_data = &mini2440_dm9k_pdata,
|
||||||
|
},
|
||||||
|
};
|
||||||
|
|
||||||
|
/* CON5
|
||||||
|
* +--+ /-----\
|
||||||
|
* | | | |
|
||||||
|
* | | | BAT |
|
||||||
|
* | | \_____/
|
||||||
|
* | |
|
||||||
|
* | | +----+ +----+
|
||||||
|
* | | | K5 | | K1 |
|
||||||
|
* | | +----+ +----+
|
||||||
|
* | | +----+ +----+
|
||||||
|
* | | | K4 | | K2 |
|
||||||
|
* | | +----+ +----+
|
||||||
|
* | | +----+ +----+
|
||||||
|
* | | | K6 | | K3 |
|
||||||
|
* | | +----+ +----+
|
||||||
|
* .....
|
||||||
|
*/
|
||||||
|
static struct gpio_keys_button mini2440_buttons[] __initdata = {
|
||||||
|
{
|
||||||
|
.gpio = S3C2410_GPG(0), /* K1 */
|
||||||
|
.code = KEY_F1,
|
||||||
|
.desc = "Button 1",
|
||||||
|
.active_low = 1,
|
||||||
|
},
|
||||||
|
{
|
||||||
|
.gpio = S3C2410_GPG(3), /* K2 */
|
||||||
|
.code = KEY_F2,
|
||||||
|
.desc = "Button 2",
|
||||||
|
.active_low = 1,
|
||||||
|
},
|
||||||
|
{
|
||||||
|
.gpio = S3C2410_GPG(5), /* K3 */
|
||||||
|
.code = KEY_F3,
|
||||||
|
.desc = "Button 3",
|
||||||
|
.active_low = 1,
|
||||||
|
},
|
||||||
|
{
|
||||||
|
.gpio = S3C2410_GPG(6), /* K4 */
|
||||||
|
.code = KEY_POWER,
|
||||||
|
.desc = "Power",
|
||||||
|
.active_low = 1,
|
||||||
|
},
|
||||||
|
{
|
||||||
|
.gpio = S3C2410_GPG(7), /* K5 */
|
||||||
|
.code = KEY_F5,
|
||||||
|
.desc = "Button 5",
|
||||||
|
.active_low = 1,
|
||||||
|
},
|
||||||
|
#if 0
|
||||||
|
/* this pin is also known as TCLK1 and seems to already
|
||||||
|
* marked as "in use" somehow in the kernel -- possibly wrongly */
|
||||||
|
{
|
||||||
|
.gpio = S3C2410_GPG(11), /* K6 */
|
||||||
|
.code = KEY_F6,
|
||||||
|
.desc = "Button 6",
|
||||||
|
.active_low = 1,
|
||||||
|
},
|
||||||
|
#endif
|
||||||
|
};
|
||||||
|
|
||||||
|
static struct gpio_keys_platform_data mini2440_button_data __initdata = {
|
||||||
|
.buttons = mini2440_buttons,
|
||||||
|
.nbuttons = ARRAY_SIZE(mini2440_buttons),
|
||||||
|
};
|
||||||
|
|
||||||
|
static struct platform_device mini2440_button_device __initdata = {
|
||||||
|
.name = "gpio-keys",
|
||||||
|
.id = -1,
|
||||||
|
.dev = {
|
||||||
|
.platform_data = &mini2440_button_data,
|
||||||
|
}
|
||||||
|
};
|
||||||
|
|
||||||
|
/* LEDS */
|
||||||
|
|
||||||
|
static struct s3c24xx_led_platdata mini2440_led1_pdata __initdata = {
|
||||||
|
.name = "led1",
|
||||||
|
.gpio = S3C2410_GPB(5),
|
||||||
|
.flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE,
|
||||||
|
.def_trigger = "heartbeat",
|
||||||
|
};
|
||||||
|
|
||||||
|
static struct s3c24xx_led_platdata mini2440_led2_pdata __initdata = {
|
||||||
|
.name = "led2",
|
||||||
|
.gpio = S3C2410_GPB(6),
|
||||||
|
.flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE,
|
||||||
|
.def_trigger = "nand-disk",
|
||||||
|
};
|
||||||
|
|
||||||
|
static struct s3c24xx_led_platdata mini2440_led3_pdata __initdata = {
|
||||||
|
.name = "led3",
|
||||||
|
.gpio = S3C2410_GPB(7),
|
||||||
|
.flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE,
|
||||||
|
.def_trigger = "mmc0",
|
||||||
|
};
|
||||||
|
|
||||||
|
static struct s3c24xx_led_platdata mini2440_led4_pdata __initdata = {
|
||||||
|
.name = "led4",
|
||||||
|
.gpio = S3C2410_GPB(8),
|
||||||
|
.flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE,
|
||||||
|
.def_trigger = "",
|
||||||
|
};
|
||||||
|
|
||||||
|
static struct s3c24xx_led_platdata mini2440_led_backlight_pdata __initdata = {
|
||||||
|
.name = "backlight",
|
||||||
|
.gpio = S3C2410_GPG(4),
|
||||||
|
.def_trigger = "backlight",
|
||||||
|
};
|
||||||
|
|
||||||
|
static struct platform_device mini2440_led1 __initdata = {
|
||||||
|
.name = "s3c24xx_led",
|
||||||
|
.id = 1,
|
||||||
|
.dev = {
|
||||||
|
.platform_data = &mini2440_led1_pdata,
|
||||||
|
},
|
||||||
|
};
|
||||||
|
|
||||||
|
static struct platform_device mini2440_led2 __initdata = {
|
||||||
|
.name = "s3c24xx_led",
|
||||||
|
.id = 2,
|
||||||
|
.dev = {
|
||||||
|
.platform_data = &mini2440_led2_pdata,
|
||||||
|
},
|
||||||
|
};
|
||||||
|
|
||||||
|
static struct platform_device mini2440_led3 __initdata = {
|
||||||
|
.name = "s3c24xx_led",
|
||||||
|
.id = 3,
|
||||||
|
.dev = {
|
||||||
|
.platform_data = &mini2440_led3_pdata,
|
||||||
|
},
|
||||||
|
};
|
||||||
|
|
||||||
|
static struct platform_device mini2440_led4 __initdata = {
|
||||||
|
.name = "s3c24xx_led",
|
||||||
|
.id = 4,
|
||||||
|
.dev = {
|
||||||
|
.platform_data = &mini2440_led4_pdata,
|
||||||
|
},
|
||||||
|
};
|
||||||
|
|
||||||
|
static struct platform_device mini2440_led_backlight __initdata = {
|
||||||
|
.name = "s3c24xx_led",
|
||||||
|
.id = 5,
|
||||||
|
.dev = {
|
||||||
|
.platform_data = &mini2440_led_backlight_pdata,
|
||||||
|
},
|
||||||
|
};
|
||||||
|
|
||||||
|
/* AUDIO */
|
||||||
|
|
||||||
|
static struct s3c24xx_uda134x_platform_data mini2440_audio_pins __initdata = {
|
||||||
|
.l3_clk = S3C2410_GPB(4),
|
||||||
|
.l3_mode = S3C2410_GPB(2),
|
||||||
|
.l3_data = S3C2410_GPB(3),
|
||||||
|
.model = UDA134X_UDA1341
|
||||||
|
};
|
||||||
|
|
||||||
|
static struct platform_device mini2440_audio __initdata = {
|
||||||
|
.name = "s3c24xx_uda134x",
|
||||||
|
.id = 0,
|
||||||
|
.dev = {
|
||||||
|
.platform_data = &mini2440_audio_pins,
|
||||||
|
},
|
||||||
|
};
|
||||||
|
|
||||||
|
/*
|
||||||
|
* I2C devices
|
||||||
|
*/
|
||||||
|
static struct at24_platform_data at24c08 = {
|
||||||
|
.byte_len = SZ_8K / 8,
|
||||||
|
.page_size = 16,
|
||||||
|
};
|
||||||
|
|
||||||
|
static struct i2c_board_info mini2440_i2c_devs[] __initdata = {
|
||||||
|
{
|
||||||
|
I2C_BOARD_INFO("24c08", 0x50),
|
||||||
|
.platform_data = &at24c08,
|
||||||
|
},
|
||||||
|
};
|
||||||
|
|
||||||
|
static struct platform_device *mini2440_devices[] __initdata = {
|
||||||
|
&s3c_device_usb,
|
||||||
|
&s3c_device_wdt,
|
||||||
|
/* &s3c_device_adc,*/ /* ADC doesn't like living with touchscreen ! */
|
||||||
|
&s3c_device_i2c0,
|
||||||
|
&s3c_device_rtc,
|
||||||
|
&s3c_device_usbgadget,
|
||||||
|
&mini2440_device_eth,
|
||||||
|
&mini2440_led1,
|
||||||
|
&mini2440_led2,
|
||||||
|
&mini2440_led3,
|
||||||
|
&mini2440_led4,
|
||||||
|
&mini2440_button_device,
|
||||||
|
&s3c_device_nand,
|
||||||
|
&s3c_device_sdi,
|
||||||
|
&s3c_device_iis,
|
||||||
|
&mini2440_audio,
|
||||||
|
/* &s3c_device_timer[0],*/ /* buzzer pwm, no API for it */
|
||||||
|
/* remaining devices are optional */
|
||||||
|
};
|
||||||
|
|
||||||
|
static void __init mini2440_map_io(void)
|
||||||
|
{
|
||||||
|
s3c24xx_init_io(mini2440_iodesc, ARRAY_SIZE(mini2440_iodesc));
|
||||||
|
s3c24xx_init_clocks(12000000);
|
||||||
|
s3c24xx_init_uarts(mini2440_uartcfgs, ARRAY_SIZE(mini2440_uartcfgs));
|
||||||
|
|
||||||
|
s3c_device_nand.dev.platform_data = &mini2440_nand_info;
|
||||||
|
s3c_device_sdi.dev.platform_data = &mini2440_mmc_cfg;
|
||||||
|
}
|
||||||
|
|
||||||
|
/*
|
||||||
|
* mini2440_features string
|
||||||
|
*
|
||||||
|
* t = Touchscreen present
|
||||||
|
* b = backlight control
|
||||||
|
* c = camera [TODO]
|
||||||
|
* 0-9 LCD configuration
|
||||||
|
*
|
||||||
|
*/
|
||||||
|
static char mini2440_features_str[12] __initdata = "0tb";
|
||||||
|
|
||||||
|
static int __init mini2440_features_setup(char *str)
|
||||||
|
{
|
||||||
|
if (str)
|
||||||
|
strlcpy(mini2440_features_str, str, sizeof(mini2440_features_str));
|
||||||
|
return 1;
|
||||||
|
}
|
||||||
|
|
||||||
|
__setup("mini2440=", mini2440_features_setup);
|
||||||
|
|
||||||
|
#define FEATURE_SCREEN (1 << 0)
|
||||||
|
#define FEATURE_BACKLIGHT (1 << 1)
|
||||||
|
#define FEATURE_TOUCH (1 << 2)
|
||||||
|
#define FEATURE_CAMERA (1 << 3)
|
||||||
|
|
||||||
|
struct mini2440_features_t {
|
||||||
|
int count;
|
||||||
|
int done;
|
||||||
|
int lcd_index;
|
||||||
|
struct platform_device *optional[8];
|
||||||
|
};
|
||||||
|
|
||||||
|
static void mini2440_parse_features(
|
||||||
|
struct mini2440_features_t * features,
|
||||||
|
const char * features_str )
|
||||||
|
{
|
||||||
|
const char * fp = features_str;
|
||||||
|
|
||||||
|
features->count = 0;
|
||||||
|
features->done = 0;
|
||||||
|
features->lcd_index = -1;
|
||||||
|
|
||||||
|
while (*fp) {
|
||||||
|
char f = *fp++;
|
||||||
|
|
||||||
|
switch (f) {
|
||||||
|
case '0'...'9': /* tft screen */
|
||||||
|
if (features->done & FEATURE_SCREEN) {
|
||||||
|
printk(KERN_INFO "MINI2440: '%c' ignored, "
|
||||||
|
"screen type already set\n", f);
|
||||||
|
} else {
|
||||||
|
int li = f - '0';
|
||||||
|
if (li >= ARRAY_SIZE(mini2440_lcd_cfg))
|
||||||
|
printk(KERN_INFO "MINI2440: "
|
||||||
|
"'%c' out of range LCD mode\n", f);
|
||||||
|
else {
|
||||||
|
features->optional[features->count++] =
|
||||||
|
&s3c_device_lcd;
|
||||||
|
features->lcd_index = li;
|
||||||
|
}
|
||||||
|
}
|
||||||
|
features->done |= FEATURE_SCREEN;
|
||||||
|
break;
|
||||||
|
case 'b':
|
||||||
|
if (features->done & FEATURE_BACKLIGHT)
|
||||||
|
printk(KERN_INFO "MINI2440: '%c' ignored, "
|
||||||
|
"backlight already set\n", f);
|
||||||
|
else {
|
||||||
|
features->optional[features->count++] =
|
||||||
|
&mini2440_led_backlight;
|
||||||
|
}
|
||||||
|
features->done |= FEATURE_BACKLIGHT;
|
||||||
|
break;
|
||||||
|
case 't':
|
||||||
|
printk(KERN_INFO "MINI2440: '%c' ignored, "
|
||||||
|
"touchscreen not compiled in\n", f);
|
||||||
|
break;
|
||||||
|
case 'c':
|
||||||
|
if (features->done & FEATURE_CAMERA)
|
||||||
|
printk(KERN_INFO "MINI2440: '%c' ignored, "
|
||||||
|
"camera already registered\n", f);
|
||||||
|
else
|
||||||
|
features->optional[features->count++] =
|
||||||
|
&s3c_device_camif;
|
||||||
|
features->done |= FEATURE_CAMERA;
|
||||||
|
break;
|
||||||
|
}
|
||||||
|
}
|
||||||
|
}
|
||||||
|
|
||||||
|
static void __init mini2440_init(void)
|
||||||
|
{
|
||||||
|
struct mini2440_features_t features = { 0 };
|
||||||
|
int i;
|
||||||
|
|
||||||
|
printk(KERN_INFO "MINI2440: Option string mini2440=%s\n",
|
||||||
|
mini2440_features_str);
|
||||||
|
|
||||||
|
/* Parse the feature string */
|
||||||
|
mini2440_parse_features(&features, mini2440_features_str);
|
||||||
|
|
||||||
|
/* turn LCD on */
|
||||||
|
s3c2410_gpio_cfgpin(S3C2410_GPC(0), S3C2410_GPC0_LEND);
|
||||||
|
|
||||||
|
/* Turn the backlight early on */
|
||||||
|
s3c2410_gpio_setpin(S3C2410_GPG(4), 1);
|
||||||
|
s3c2410_gpio_cfgpin(S3C2410_GPG(4), S3C2410_GPIO_OUTPUT);
|
||||||
|
|
||||||
|
/* remove pullup on optional PWM backlight -- unused on 3.5 and 7"s */
|
||||||
|
s3c2410_gpio_pullup(S3C2410_GPB(1), 0);
|
||||||
|
s3c2410_gpio_setpin(S3C2410_GPB(1), 0);
|
||||||
|
s3c2410_gpio_cfgpin(S3C2410_GPB(1), S3C2410_GPIO_INPUT);
|
||||||
|
|
||||||
|
/* Make sure the D+ pullup pin is output */
|
||||||
|
s3c2410_gpio_cfgpin(S3C2410_GPC(5), S3C2410_GPIO_OUTPUT);
|
||||||
|
|
||||||
|
/* mark the key as input, without pullups (there is one on the board) */
|
||||||
|
for (i = 0; i < ARRAY_SIZE(mini2440_buttons); i++) {
|
||||||
|
s3c2410_gpio_pullup(mini2440_buttons[i].gpio, 0);
|
||||||
|
s3c2410_gpio_cfgpin(mini2440_buttons[i].gpio,
|
||||||
|
S3C2410_GPIO_INPUT);
|
||||||
|
}
|
||||||
|
if (features.lcd_index != -1) {
|
||||||
|
int li;
|
||||||
|
|
||||||
|
mini2440_fb_info.displays =
|
||||||
|
&mini2440_lcd_cfg[features.lcd_index];
|
||||||
|
|
||||||
|
printk(KERN_INFO "MINI2440: LCD");
|
||||||
|
for (li = 0; li < ARRAY_SIZE(mini2440_lcd_cfg); li++)
|
||||||
|
if (li == features.lcd_index)
|
||||||
|
printk(" [%d:%dx%d]", li,
|
||||||
|
mini2440_lcd_cfg[li].width,
|
||||||
|
mini2440_lcd_cfg[li].height);
|
||||||
|
else
|
||||||
|
printk(" %d:%dx%d", li,
|
||||||
|
mini2440_lcd_cfg[li].width,
|
||||||
|
mini2440_lcd_cfg[li].height);
|
||||||
|
printk("\n");
|
||||||
|
s3c24xx_fb_set_platdata(&mini2440_fb_info);
|
||||||
|
}
|
||||||
|
s3c24xx_udc_set_platdata(&mini2440_udc_cfg);
|
||||||
|
s3c_i2c0_set_platdata(NULL);
|
||||||
|
i2c_register_board_info(0, mini2440_i2c_devs,
|
||||||
|
ARRAY_SIZE(mini2440_i2c_devs));
|
||||||
|
|
||||||
|
platform_add_devices(mini2440_devices, ARRAY_SIZE(mini2440_devices));
|
||||||
|
|
||||||
|
if (features.count) /* the optional features */
|
||||||
|
platform_add_devices(features.optional, features.count);
|
||||||
|
|
||||||
|
}
|
||||||
|
|
||||||
|
|
||||||
|
MACHINE_START(MINI2440, "MINI2440")
|
||||||
|
/* Maintainer: Michel Pollet <buserror@gmail.com> */
|
||||||
|
.phys_io = S3C2410_PA_UART,
|
||||||
|
.io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc,
|
||||||
|
.boot_params = S3C2410_SDRAM_PA + 0x100,
|
||||||
|
.map_io = mini2440_map_io,
|
||||||
|
.init_machine = mini2440_init,
|
||||||
|
.init_irq = s3c24xx_init_irq,
|
||||||
|
.timer = &s3c24xx_timer,
|
||||||
|
MACHINE_END
|
||||||
Loading…
Add table
Reference in a new issue