Merge "usb: phy: qusb2: Add support to vote for regulator L2a"

Documentation/devicetree/bindings/usb/msm-phy.txt

@@ -178,6 +178,7 @@ Required properties:
 	"vdd" : vdd supply for digital circuit operation
 	"vdda18" : 1.8v high-voltage analog supply
 	"vdda33" : 3.3v high-voltage analog supply
+	"vdda12" : 1.2v high-voltage analog supply
  - qcom,vdd-voltage-level: This property must be a list of three integer
    values (no, min, max) where each value represents either a voltage in
    microvolts or a value corresponding to voltage corner

arch/arm/boot/dts/qcom/msm8998.dtsi

@@ -1762,6 +1762,7 @@
 		reg-names = "qusb_phy_base",
 				"tcsr_clamp_dig_n_1p8";
 		vdd-supply = <&pm8998_l1>;
+		vdda12-supply = <&pm8998_l2>;
 		vdda18-supply = <&pm8998_l12>;
 		vdda33-supply = <&pm8998_l24>;
 		qcom,vdd-voltage-level = <0 880000 880000>;

drivers/usb/phy/phy-msm-qusb-v2.c

@@ -51,6 +51,10 @@
 
 #define QUSB2PHY_PORT_TUNE1		0x23c
 
+#define QUSB2PHY_1P2_VOL_MIN           1200000 /* uV */
+#define QUSB2PHY_1P2_VOL_MAX           1200000 /* uV */
+#define QUSB2PHY_1P2_HPM_LOAD          23000
+
 #define QUSB2PHY_1P8_VOL_MIN           1800000 /* uV */
 #define QUSB2PHY_1P8_VOL_MAX           1800000 /* uV */
 #define QUSB2PHY_1P8_HPM_LOAD          30000   /* uA */
@@ -83,6 +87,7 @@ struct qusb_phy {
 	struct regulator	*vdd;
 	struct regulator	*vdda33;
 	struct regulator	*vdda18;
+	struct regulator	*vdda12;
 	int			vdd_levels[3]; /* none, low, high */
 	int			init_seq_len;
 	int			*qusb_phy_init_seq;
@@ -184,10 +189,30 @@ static int qusb_phy_enable_power(struct qusb_phy *qphy, bool on,
 		}
 	}
 
+	ret = regulator_set_load(qphy->vdda12, QUSB2PHY_1P2_HPM_LOAD);
+	if (ret < 0) {
+		dev_err(qphy->phy.dev, "Unable to set HPM of vdda12:%d\n", ret);
+		goto disable_vdd;
+	}
+
+	ret = regulator_set_voltage(qphy->vdda12, QUSB2PHY_1P2_VOL_MIN,
+						QUSB2PHY_1P2_VOL_MAX);
+	if (ret) {
+		dev_err(qphy->phy.dev,
+				"Unable to set voltage for vdda12:%d\n", ret);
+		goto put_vdda12_lpm;
+	}
+
+	ret = regulator_enable(qphy->vdda12);
+	if (ret) {
+		dev_err(qphy->phy.dev, "Unable to enable vdda12:%d\n", ret);
+		goto unset_vdda12;
+	}
+
 	ret = regulator_set_load(qphy->vdda18, QUSB2PHY_1P8_HPM_LOAD);
 	if (ret < 0) {
 		dev_err(qphy->phy.dev, "Unable to set HPM of vdda18:%d\n", ret);
-		goto disable_vdd;
+		goto disable_vdda12;
 	}
 
 	ret = regulator_set_voltage(qphy->vdda18, QUSB2PHY_1P8_VOL_MIN,
@@ -262,6 +287,20 @@ put_vdda18_lpm:
 	if (ret < 0)
 		dev_err(qphy->phy.dev, "Unable to set LPM of vdda18\n");
 
+disable_vdda12:
+	ret = regulator_disable(qphy->vdda12);
+	if (ret)
+		dev_err(qphy->phy.dev, "Unable to disable vdda12:%d\n", ret);
+unset_vdda12:
+	ret = regulator_set_voltage(qphy->vdda12, 0, QUSB2PHY_1P2_VOL_MAX);
+	if (ret)
+		dev_err(qphy->phy.dev,
+			"Unable to set (0) voltage for vdda12:%d\n", ret);
+put_vdda12_lpm:
+	ret = regulator_set_load(qphy->vdda12, 0);
+	if (ret < 0)
+		dev_err(qphy->phy.dev, "Unable to set LPM of vdda12\n");
+
 disable_vdd:
 	if (toggle_vdd) {
 		ret = regulator_disable(qphy->vdd);
@@ -985,6 +1024,12 @@ static int qusb_phy_probe(struct platform_device *pdev)
 		return PTR_ERR(qphy->vdda18);
 	}
 
+	qphy->vdda12 = devm_regulator_get(dev, "vdda12");
+	if (IS_ERR(qphy->vdda12)) {
+		dev_err(dev, "unable to get vdda12 supply\n");
+		return PTR_ERR(qphy->vdda12);
+	}
+
 	platform_set_drvdata(pdev, qphy);
 
 	qphy->phy.label			= "msm-qusb-phy-v2";