From 22374fbedb2ce03ef81323b3f7ceb3fa29344aa6 Mon Sep 17 00:00:00 2001 From: Robert Baldyga Date: Mon, 29 Jun 2015 15:22:34 +0200 Subject: [PATCH 01/22] ARM: dts: Add DMA support for serial ports in exynos4 Enable DMA transfers for serial ports. Signed-off-by: Robert Baldyga Signed-off-by: Krzysztof Kozlowski --- arch/arm/boot/dts/exynos4.dtsi | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/arch/arm/boot/dts/exynos4.dtsi b/arch/arm/boot/dts/exynos4.dtsi index 98c0a368b777..3184e10f260a 100644 --- a/arch/arm/boot/dts/exynos4.dtsi +++ b/arch/arm/boot/dts/exynos4.dtsi @@ -431,6 +431,8 @@ interrupts = <0 52 0>; clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>; clock-names = "uart", "clk_uart_baud0"; + dmas = <&pdma0 15>, <&pdma0 16>; + dma-names = "rx", "tx"; status = "disabled"; }; @@ -440,6 +442,8 @@ interrupts = <0 53 0>; clocks = <&clock CLK_UART1>, <&clock CLK_SCLK_UART1>; clock-names = "uart", "clk_uart_baud0"; + dmas = <&pdma1 15>, <&pdma1 16>; + dma-names = "rx", "tx"; status = "disabled"; }; @@ -449,6 +453,8 @@ interrupts = <0 54 0>; clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>; clock-names = "uart", "clk_uart_baud0"; + dmas = <&pdma0 17>, <&pdma0 18>; + dma-names = "rx", "tx"; status = "disabled"; }; @@ -458,6 +464,8 @@ interrupts = <0 55 0>; clocks = <&clock CLK_UART3>, <&clock CLK_SCLK_UART3>; clock-names = "uart", "clk_uart_baud0"; + dmas = <&pdma1 17>, <&pdma1 18>; + dma-names = "rx", "tx"; status = "disabled"; }; From a68371632b86d682992185ecf97316700a5a0f14 Mon Sep 17 00:00:00 2001 From: Krzysztof Kozlowski Date: Wed, 16 Sep 2015 08:37:02 +0900 Subject: [PATCH 02/22] ARM: dts: Fix LEDs on exynos5422-odroidxu3 The LEDs on Odroid XU3 family boards could not properly probe because PWM outputs were reduced only to PWM for fan. Fix it for Odroid XU3 and XU3-Lite boards by switching to usage of all 4 outputs (although the PWM for MIPI probably is redundant because board does not have MIPI connector available). This fixes warnings on dmesg: [ 4.838712] samsung-pwm 12dd0000.pwm: tried to request PWM channel 1 without output [ 4.838725] leds_pwm pwmleds: unable to request PWM for green:mmc0: -22 [ 4.838767] leds_pwm: probe of pwmleds failed with error -22 Fixes: b685d540cc26 ("ARM: dts: Add pwm-fan node for exynos5422-odroidxu3") Signed-off-by: Krzysztof Kozlowski Signed-off-by: Kukjin Kim --- arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi index 79ffdfe712aa..3b43e57845ae 100644 --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi @@ -472,7 +472,6 @@ */ pinctrl-0 = <&pwm0_out &pwm1_out &pwm2_out &pwm3_out>; pinctrl-names = "default"; - samsung,pwm-outputs = <0>; status = "okay"; }; From 1605b60ad064c7019db8ade07f0b7bdc8c197b93 Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Thu, 17 Sep 2015 07:46:28 +0900 Subject: [PATCH 03/22] ARM: dts: add suspend opp to exynos4412 Mark 800MHz OPP as a suspend opp for Exynos4412 based boards so effectively cpufreq-dt driver behavior w.r.t. suspend frequency matches what the old exynos-cpufreq driver has been doing. This patch fixes suspend/resume support on Exynos4412 based Trats2 board and reboot hang on Exynos4412 based Odroid U3 board. Cc: Thomas Abraham Cc: Javier Martinez Canillas Cc: Marek Szyprowski Cc: Tobias Jakobi Acked-by: Viresh Kumar Signed-off-by: Bartlomiej Zolnierkiewicz Acked-by: Krzysztof Kozlowski Signed-off-by: Kukjin Kim --- arch/arm/boot/dts/exynos4412.dtsi | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/boot/dts/exynos4412.dtsi b/arch/arm/boot/dts/exynos4412.dtsi index ca0e3c15977f..294cfe40388d 100644 --- a/arch/arm/boot/dts/exynos4412.dtsi +++ b/arch/arm/boot/dts/exynos4412.dtsi @@ -98,6 +98,7 @@ opp-hz = /bits/ 64 <800000000>; opp-microvolt = <1000000>; clock-latency-ns = <200000>; + opp-suspend; }; opp07 { opp-hz = /bits/ 64 <900000000>; From 41553f267a369f24244867f5d6c8d4df254906b7 Mon Sep 17 00:00:00 2001 From: Lukasz Majewski Date: Mon, 17 Aug 2015 08:53:47 +0900 Subject: [PATCH 04/22] dt-bindings: Documentation entry to explain how to use PWM FAN as a cooling device Explanation of several properties, which allow PWM fan working as a cooling device, have been embraced in this commit. Signed-off-by: Lukasz Majewski Acked-by: Eduardo Valentin Acked-by: Krzysztof Kozlowski Signed-off-by: Kukjin Kim --- .../devicetree/bindings/hwmon/pwm-fan.txt | 29 +++++++++++++++++-- 1 file changed, 27 insertions(+), 2 deletions(-) diff --git a/Documentation/devicetree/bindings/hwmon/pwm-fan.txt b/Documentation/devicetree/bindings/hwmon/pwm-fan.txt index 610757ce4492..c6d533202d3e 100644 --- a/Documentation/devicetree/bindings/hwmon/pwm-fan.txt +++ b/Documentation/devicetree/bindings/hwmon/pwm-fan.txt @@ -3,10 +3,35 @@ Bindings for a fan connected to the PWM lines Required properties: - compatible : "pwm-fan" - pwms : the PWM that is used to control the PWM fan +- cooling-levels : PWM duty cycle values in a range from 0 to 255 + which correspond to thermal cooling states Example: - pwm-fan { + fan0: pwm-fan { compatible = "pwm-fan"; - status = "okay"; + cooling-min-state = <0>; + cooling-max-state = <3>; + #cooling-cells = <2>; pwms = <&pwm 0 10000 0>; + cooling-levels = <0 102 170 230>; }; + + thermal-zones { + cpu_thermal: cpu-thermal { + thermal-sensors = <&tmu 0>; + polling-delay-passive = <0>; + polling-delay = <0>; + trips { + cpu_alert1: cpu-alert1 { + temperature = <100000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + }; + cooling-maps { + map0 { + trip = <&cpu_alert1>; + cooling-device = <&fan0 0 1>; + }; + }; + }; From ee6011f299f3e75458bd6e91db5795e5adedd6fe Mon Sep 17 00:00:00 2001 From: Kamil Debski Date: Mon, 17 Aug 2015 08:53:47 +0900 Subject: [PATCH 05/22] ARM: dts: Add pwm-fan node for exynos4412-odroidu3 Add pwm-fan node to the Odroid-U3 board file to enable PWM control of the cooling fan. In addition, add the "pwm" label to the pwm@139D0000 node in the exynos4412.dtsi. Signed-off-by: Kamil Debski Signed-off-by: Lukasz Majewski Reviewed-by: Krzysztof Kozlowski Signed-off-by: Kukjin Kim --- arch/arm/boot/dts/exynos4412-odroidu3.dts | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/arch/arm/boot/dts/exynos4412-odroidu3.dts b/arch/arm/boot/dts/exynos4412-odroidu3.dts index 8632f35c6c26..54b3bc1dba1d 100644 --- a/arch/arm/boot/dts/exynos4412-odroidu3.dts +++ b/arch/arm/boot/dts/exynos4412-odroidu3.dts @@ -32,6 +32,18 @@ linux,default-trigger = "heartbeat"; }; }; + + pwm-fan { + compatible = "pwm-fan"; + pwms = <&pwm 0 10000 0>; + }; +}; + +&pwm { + pinctrl-0 = <&pwm0_out>; + pinctrl-names = "default"; + samsung,pwm-outputs = <0>; + status = "okay"; }; &usb3503 { From d3981d1e0a34bd294d620476a33967452e0298a7 Mon Sep 17 00:00:00 2001 From: Lukasz Majewski Date: Mon, 17 Aug 2015 08:53:48 +0900 Subject: [PATCH 06/22] ARM: dts: use pwm-fan device as a cooling device for exynos4412-odroidu3 With those bindings it is possible to use pwm-fan device available in Odroid U3 as a cooling device. Signed-off-by: Lukasz Majewski Acked-by: Eduardo Valentin Reviewed-by: Krzysztof Kozlowski Signed-off-by: Kukjin Kim --- arch/arm/boot/dts/exynos4412-odroidu3.dts | 33 ++++++++++++++++++++++- 1 file changed, 32 insertions(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/exynos4412-odroidu3.dts b/arch/arm/boot/dts/exynos4412-odroidu3.dts index 54b3bc1dba1d..1e6ef99eef59 100644 --- a/arch/arm/boot/dts/exynos4412-odroidu3.dts +++ b/arch/arm/boot/dts/exynos4412-odroidu3.dts @@ -33,9 +33,40 @@ }; }; - pwm-fan { + fan0: pwm-fan { compatible = "pwm-fan"; pwms = <&pwm 0 10000 0>; + cooling-min-state = <0>; + cooling-max-state = <3>; + #cooling-cells = <2>; + cooling-levels = <0 102 170 230>; + }; + + thermal-zones { + cpu_thermal: cpu-thermal { + cooling-maps { + map0 { + trip = <&cpu_alert1>; + cooling-device = <&cpu0 7 7>; + }; + map1 { + trip = <&cpu_alert2>; + cooling-device = <&cpu0 13 13>; + }; + map2 { + trip = <&cpu_alert0>; + cooling-device = <&fan0 0 1>; + }; + map3 { + trip = <&cpu_alert1>; + cooling-device = <&fan0 1 2>; + }; + map4 { + trip = <&cpu_alert2>; + cooling-device = <&fan0 2 3>; + }; + }; + }; }; }; From 6a4479f965430457f301c61dfe7b0dd76f691e9e Mon Sep 17 00:00:00 2001 From: Krzysztof Kozlowski Date: Mon, 17 Aug 2015 08:55:51 +0900 Subject: [PATCH 07/22] dt-bindings: Document grounded ACOKB pin on S2MPS11 Document a new Device Tree property 'samsung,s2mps11-acokb-ground' indicating that ACOKB pin of S2MPS11 PMIC is connected to the ground so the PMIC must manually set PWRHOLD bit in CTRL1 register to turn off the power. Signed-off-by: Krzysztof Kozlowski Reviewed-by: Javier Martinez Canillas Acked-by: Lee Jones Signed-off-by: Kukjin Kim --- Documentation/devicetree/bindings/mfd/s2mps11.txt | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/Documentation/devicetree/bindings/mfd/s2mps11.txt b/Documentation/devicetree/bindings/mfd/s2mps11.txt index 57a045016fca..90eaef393325 100644 --- a/Documentation/devicetree/bindings/mfd/s2mps11.txt +++ b/Documentation/devicetree/bindings/mfd/s2mps11.txt @@ -15,6 +15,10 @@ Optional properties: - interrupt-parent: Specifies the phandle of the interrupt controller to which the interrupts from s2mps11 are delivered to. - interrupts: Interrupt specifiers for interrupt sources. +- samsung,s2mps11-acokb-ground: Indicates that ACOKB pin of S2MPS11 PMIC is + connected to the ground so the PMIC must manually set PWRHOLD bit in CTRL1 + register to turn off the power. Usually the ACOKB is pulled up to VBATT so + when PWRHOLD pin goes low, the rising ACOKB will trigger power off. Optional nodes: - clocks: s2mps11, s2mps13 and s5m8767 provide three(AP/CP/BT) buffered 32.768 From 0fb033bb3a384fdf1c08bcfaf429ca6431de91c7 Mon Sep 17 00:00:00 2001 From: Krzysztof Kozlowski Date: Mon, 17 Aug 2015 08:55:51 +0900 Subject: [PATCH 08/22] ARM: dts: Fix power off method for exynos5422-odroidxu3-common The Odroid XU3 family boards have ACOKB pin of PMIC grounded, instead of pulled up as usual. This means that PMIC must manually set PWRHOLD field in its CTRL1 register to low before initiating power down. This fixes Odroid XU3 powering off: [ 25.966053] reboot: Power down [ 25.967679] Power down. [ 26.070174] Power down failed, please power off system manually. Signed-off-by: Krzysztof Kozlowski Reported-by: Anand Moon Reviewed-by: Javier Martinez Canillas Signed-off-by: Kukjin Kim --- arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi index 3b43e57845ae..90d298dce851 100644 --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi @@ -160,6 +160,7 @@ s2mps11,buck2-ramp-enable = <1>; s2mps11,buck3-ramp-enable = <1>; s2mps11,buck4-ramp-enable = <1>; + samsung,s2mps11-acokb-ground; interrupt-parent = <&gpx0>; interrupts = <4 IRQ_TYPE_EDGE_FALLING>; From 8cec734904f55d5551ac97fa9910752ef521a673 Mon Sep 17 00:00:00 2001 From: Krzysztof Kozlowski Date: Wed, 16 Sep 2015 08:37:07 +0900 Subject: [PATCH 09/22] ARM: dts: Split audio configuration to separate exynos5422-odroidxu3-audio The Odroid XU4 board does not have audio codec so before adding DTS for new board split the audio codec to separate DTSI file. Include the audio codec DTSI in Odroid XU3 and XU3-Lite boards. Signed-off-by: Krzysztof Kozlowski Reviewed-by: Javier Martinez Canillas Signed-off-by: Kukjin Kim --- .../boot/dts/exynos5422-odroidxu3-audio.dtsi | 61 +++++++++++++++++++ .../boot/dts/exynos5422-odroidxu3-common.dtsi | 47 -------------- .../boot/dts/exynos5422-odroidxu3-lite.dts | 1 + arch/arm/boot/dts/exynos5422-odroidxu3.dts | 1 + 4 files changed, 63 insertions(+), 47 deletions(-) create mode 100644 arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi new file mode 100644 index 000000000000..9493923ec652 --- /dev/null +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi @@ -0,0 +1,61 @@ +/* + * Hardkernel Odroid XU3 Audio Codec device tree source + * + * Copyright (c) 2015 Krzysztof Kozlowski + * Copyright (c) 2014 Collabora Ltd. + * Copyright (c) 2013 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +/ { + sound: sound { + compatible = "simple-audio-card"; + + simple-audio-card,name = "Odroid-XU3"; + simple-audio-card,widgets = + "Headphone", "Headphone Jack", + "Speakers", "Speakers"; + simple-audio-card,routing = + "Headphone Jack", "HPL", + "Headphone Jack", "HPR", + "Headphone Jack", "MICBIAS", + "IN1", "Headphone Jack", + "Speakers", "SPKL", + "Speakers", "SPKR"; + + simple-audio-card,format = "i2s"; + simple-audio-card,bitclock-master = <&link0_codec>; + simple-audio-card,frame-master = <&link0_codec>; + + simple-audio-card,cpu { + sound-dai = <&i2s0 0>; + system-clock-frequency = <19200000>; + }; + + link0_codec: simple-audio-card,codec { + sound-dai = <&max98090>; + clocks = <&i2s0 CLK_I2S_CDCLK>; + }; + }; +}; + +&hsi2c_5 { + status = "okay"; + max98090: max98090@10 { + compatible = "maxim,max98090"; + reg = <0x10>; + interrupt-parent = <&gpx3>; + interrupts = <2 0>; + clocks = <&i2s0 CLK_I2S_CDCLK>; + clock-names = "mclk"; + #sound-dai-cells = <0>; + }; +}; + +&i2s0 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi index 90d298dce851..2f0fb8678e9f 100644 --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi @@ -80,36 +80,6 @@ }; }; - sound: sound { - compatible = "simple-audio-card"; - - simple-audio-card,name = "Odroid-XU3"; - simple-audio-card,widgets = - "Headphone", "Headphone Jack", - "Speakers", "Speakers"; - simple-audio-card,routing = - "Headphone Jack", "HPL", - "Headphone Jack", "HPR", - "Headphone Jack", "MICBIAS", - "IN1", "Headphone Jack", - "Speakers", "SPKL", - "Speakers", "SPKR"; - - simple-audio-card,format = "i2s"; - simple-audio-card,bitclock-master = <&link0_codec>; - simple-audio-card,frame-master = <&link0_codec>; - - simple-audio-card,cpu { - sound-dai = <&i2s0 0>; - system-clock-frequency = <19200000>; - }; - - link0_codec: simple-audio-card,codec { - sound-dai = <&max98090>; - clocks = <&i2s0 CLK_I2S_CDCLK>; - }; - }; - fan0: pwm-fan { compatible = "pwm-fan"; pwms = <&pwm 0 20972 0>; @@ -376,19 +346,6 @@ }; }; -&hsi2c_5 { - status = "okay"; - max98090: max98090@10 { - compatible = "maxim,max98090"; - reg = <0x10>; - interrupt-parent = <&gpx3>; - interrupts = <2 0>; - clocks = <&i2s0 CLK_I2S_CDCLK>; - clock-names = "mclk"; - #sound-dai-cells = <0>; - }; -}; - &i2c_2 { samsung,i2c-sda-delay = <100>; samsung,i2c-max-bus-freq = <66000>; @@ -400,10 +357,6 @@ }; }; -&i2s0 { - status = "okay"; -}; - &mfc { samsung,mfc-r = <0x43000000 0x800000>; samsung,mfc-l = <0x51000000 0x800000>; diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts b/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts index c06882bbb822..9c0cea99c996 100644 --- a/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts @@ -13,6 +13,7 @@ /dts-v1/; #include "exynos5422-odroidxu3-common.dtsi" +#include "exynos5422-odroidxu3-audio.dtsi" / { model = "Hardkernel Odroid XU3 Lite"; diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3.dts b/arch/arm/boot/dts/exynos5422-odroidxu3.dts index 78e6a502f320..d8647a469a86 100644 --- a/arch/arm/boot/dts/exynos5422-odroidxu3.dts +++ b/arch/arm/boot/dts/exynos5422-odroidxu3.dts @@ -12,6 +12,7 @@ /dts-v1/; #include "exynos5422-odroidxu3-common.dtsi" +#include "exynos5422-odroidxu3-audio.dtsi" / { model = "Hardkernel Odroid XU3"; From 6658356014cbf772c7f11154adc0c46717b3322b Mon Sep 17 00:00:00 2001 From: Krzysztof Kozlowski Date: Wed, 16 Sep 2015 08:37:11 +0900 Subject: [PATCH 10/22] ARM: dts: Add support Odroid XU4 board for exynos5422-odroidxu4 Add Hardkernel Odroid XU4 board Device Tree sources. The board differs from Odroid XU3 and XU3-Lite by: 1. No green and red LEDs (except standard red power LED). 2. Only two PWM outputs are used (fan and blue LED) 3. No audio codec. 4. Two USB3 ports in host mode (no micro USB3 connector for OTG). 5. Realtek RTL8153-CG gigabit network adapter (instead of SMSC9514). 6. Additional connector with IO ports (I2S_0, I2C_5). 7. No DisplayPort (like XU3-Lite). 8. No TI INA231 power measurement sensors (like XU3-Lite). Signed-off-by: Krzysztof Kozlowski Reviewed-by: Javier Martinez Canillas Signed-off-by: Kukjin Kim --- arch/arm/boot/dts/Makefile | 1 + .../boot/dts/exynos5422-odroidxu3-common.dtsi | 50 +------------------ .../boot/dts/exynos5422-odroidxu3-lite.dts | 50 +++++++++++++++++++ arch/arm/boot/dts/exynos5422-odroidxu3.dts | 50 +++++++++++++++++++ arch/arm/boot/dts/exynos5422-odroidxu4.dts | 48 ++++++++++++++++++ 5 files changed, 150 insertions(+), 49 deletions(-) create mode 100644 arch/arm/boot/dts/exynos5422-odroidxu4.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 233159d2eaab..3d27fe34647f 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -123,6 +123,7 @@ dtb-$(CONFIG_ARCH_EXYNOS5) += \ exynos5420-smdk5420.dtb \ exynos5422-odroidxu3.dtb \ exynos5422-odroidxu3-lite.dtb \ + exynos5422-odroidxu4.dtb \ exynos5440-sd5v1.dtb \ exynos5440-ssdk5440.dtb \ exynos5800-peach-pi.dtb diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi index 2f0fb8678e9f..a83d569baea8 100644 --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi @@ -46,40 +46,6 @@ reset-gpios = <&gpd1 0 1>; }; - pwmleds { - compatible = "pwm-leds"; - - greenled { - label = "green:mmc0"; - pwms = <&pwm 1 2000000 0>; - pwm-names = "pwm1"; - /* - * Green LED is much brighter than the others - * so limit its max brightness - */ - max_brightness = <127>; - linux,default-trigger = "mmc0"; - }; - - blueled { - label = "blue:heartbeat"; - pwms = <&pwm 2 2000000 0>; - pwm-names = "pwm2"; - max_brightness = <255>; - linux,default-trigger = "heartbeat"; - }; - }; - - gpioleds { - compatible = "gpio-leds"; - redled { - label = "red:microSD"; - gpios = <&gpx2 3 GPIO_ACTIVE_HIGH>; - default-state = "off"; - linux,default-trigger = "mmc1"; - }; - }; - fan0: pwm-fan { compatible = "pwm-fan"; pwms = <&pwm 0 20972 0>; @@ -417,18 +383,6 @@ }; }; -&pwm { - /* - * PWM 0 -- fan - * PWM 1 -- Green LED - * PWM 2 -- Blue LED - * PWM 3 -- on MIPI connector for backlight - */ - pinctrl-0 = <&pwm0_out &pwm1_out &pwm2_out &pwm3_out>; - pinctrl-names = "default"; - status = "okay"; -}; - &tmu_cpu0 { vtmu-supply = <&ldo7_reg>; status = "okay"; @@ -464,9 +418,7 @@ dr_mode = "host"; }; -&usbdrd_dwc3_1 { - dr_mode = "otg"; -}; +/* usbdrd_dwc3_1 mode customized in each board */ &usbdrd3_0 { vdd33-supply = <&ldo9_reg>; diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts b/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts index 9c0cea99c996..b1b36081f343 100644 --- a/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts @@ -18,4 +18,54 @@ / { model = "Hardkernel Odroid XU3 Lite"; compatible = "hardkernel,odroid-xu3-lite", "samsung,exynos5800", "samsung,exynos5"; + + pwmleds { + compatible = "pwm-leds"; + + greenled { + label = "green:mmc0"; + pwms = <&pwm 1 2000000 0>; + pwm-names = "pwm1"; + /* + * Green LED is much brighter than the others + * so limit its max brightness + */ + max_brightness = <127>; + linux,default-trigger = "mmc0"; + }; + + blueled { + label = "blue:heartbeat"; + pwms = <&pwm 2 2000000 0>; + pwm-names = "pwm2"; + max_brightness = <255>; + linux,default-trigger = "heartbeat"; + }; + }; + + gpioleds { + compatible = "gpio-leds"; + redled { + label = "red:microSD"; + gpios = <&gpx2 3 GPIO_ACTIVE_HIGH>; + default-state = "off"; + linux,default-trigger = "mmc1"; + }; + }; +}; + +&pwm { + /* + * PWM 0 -- fan + * PWM 1 -- Green LED + * PWM 2 -- Blue LED + * PWM 3 -- on MIPI connector for backlight + */ + pinctrl-0 = <&pwm0_out &pwm1_out &pwm2_out &pwm3_out>; + pinctrl-names = "default"; + status = "okay"; +}; + +&usbdrd_dwc3_1 { + dr_mode = "otg"; }; diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3.dts b/arch/arm/boot/dts/exynos5422-odroidxu3.dts index d8647a469a86..0c0bbdbfd85f 100644 --- a/arch/arm/boot/dts/exynos5422-odroidxu3.dts +++ b/arch/arm/boot/dts/exynos5422-odroidxu3.dts @@ -17,6 +17,40 @@ / { model = "Hardkernel Odroid XU3"; compatible = "hardkernel,odroid-xu3", "samsung,exynos5800", "samsung,exynos5"; + + pwmleds { + compatible = "pwm-leds"; + + greenled { + label = "green:mmc0"; + pwms = <&pwm 1 2000000 0>; + pwm-names = "pwm1"; + /* + * Green LED is much brighter than the others + * so limit its max brightness + */ + max_brightness = <127>; + linux,default-trigger = "mmc0"; + }; + + blueled { + label = "blue:heartbeat"; + pwms = <&pwm 2 2000000 0>; + pwm-names = "pwm2"; + max_brightness = <255>; + linux,default-trigger = "heartbeat"; + }; + }; + + gpioleds { + compatible = "gpio-leds"; + redled { + label = "red:microSD"; + gpios = <&gpx2 3 GPIO_ACTIVE_HIGH>; + default-state = "off"; + linux,default-trigger = "mmc1"; + }; + }; }; &i2c_0 { @@ -50,3 +84,19 @@ shunt-resistor = <10000>; }; }; + +&pwm { + /* + * PWM 0 -- fan + * PWM 1 -- Green LED + * PWM 2 -- Blue LED + * PWM 3 -- on MIPI connector for backlight + */ + pinctrl-0 = <&pwm0_out &pwm1_out &pwm2_out &pwm3_out>; + pinctrl-names = "default"; + status = "okay"; +}; + +&usbdrd_dwc3_1 { + dr_mode = "otg"; +}; diff --git a/arch/arm/boot/dts/exynos5422-odroidxu4.dts b/arch/arm/boot/dts/exynos5422-odroidxu4.dts new file mode 100644 index 000000000000..2faf88627a48 --- /dev/null +++ b/arch/arm/boot/dts/exynos5422-odroidxu4.dts @@ -0,0 +1,48 @@ +/* + * Hardkernel Odroid XU4 board device tree source + * + * Copyright (c) 2015 Krzysztof Kozlowski + * Copyright (c) 2014 Collabora Ltd. + * Copyright (c) 2013-2015 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +/dts-v1/; +#include "exynos5422-odroidxu3-common.dtsi" + +/ { + model = "Hardkernel Odroid XU4"; + compatible = "hardkernel,odroid-xu4", "samsung,exynos5800", \ + "samsung,exynos5"; + + pwmleds { + compatible = "pwm-leds"; + + blueled { + label = "blue:heartbeat"; + pwms = <&pwm 2 2000000 0>; + pwm-names = "pwm2"; + max_brightness = <255>; + linux,default-trigger = "heartbeat"; + }; + }; +}; + +&pwm { + /* + * PWM 0 -- fan + * PWM 2 -- Blue LED + */ + pinctrl-0 = <&pwm0_out &pwm2_out>; + pinctrl-names = "default"; + samsung,pwm-outputs = <0>, <2>; + status = "okay"; +}; + +&usbdrd_dwc3_1 { + dr_mode = "host"; +}; From 6716f6c6b8ae69e2abbea5e9c0c3c274be57d927 Mon Sep 17 00:00:00 2001 From: Vladimir Zapolskiy Date: Fri, 25 Sep 2015 20:35:32 +0300 Subject: [PATCH 11/22] ARM: dts: Fix cpu compatible value for s3c2416 The change corrects cpu compatible property to a defined one, see Documentation/devicetree/bindings/arm/cpus.txt Signed-off-by: Vladimir Zapolskiy Cc: Kukjin Kim Cc: Krzysztof Kozlowski Signed-off-by: Krzysztof Kozlowski --- arch/arm/boot/dts/s3c2416.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/s3c2416.dtsi b/arch/arm/boot/dts/s3c2416.dtsi index a5184ff56933..80f007550324 100644 --- a/arch/arm/boot/dts/s3c2416.dtsi +++ b/arch/arm/boot/dts/s3c2416.dtsi @@ -25,7 +25,7 @@ #size-cells = <0>; cpu { - compatible = "arm,arm926ejs"; + compatible = "arm,arm926ej-s"; }; }; From 4e33714eb46dfdb275893a4999b73f9b94e999f2 Mon Sep 17 00:00:00 2001 From: Tobias Jakobi Date: Mon, 21 Sep 2015 19:58:59 +0200 Subject: [PATCH 12/22] ARM: dts: Remove redundant pinctrl settings in exynos4412-odroid The pinctrl settings in i2c_0 and i2c_1 are already provided through the exynos4 dtsi. Signed-off-by: Tobias Jakobi Reviewed-by: Javier Martinez Canillas Signed-off-by: Krzysztof Kozlowski --- arch/arm/boot/dts/exynos4412-odroid-common.dtsi | 6 ------ 1 file changed, 6 deletions(-) diff --git a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi index db52841297a5..10b5a72a8e4f 100644 --- a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi +++ b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi @@ -199,8 +199,6 @@ }; &i2c_0 { - pinctrl-0 = <&i2c0_bus>; - pinctrl-names = "default"; samsung,i2c-sda-delay = <100>; samsung,i2c-max-bus-freq = <400000>; status = "okay"; @@ -424,8 +422,6 @@ }; &i2c_1 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c1_bus>; status = "okay"; max98090: max98090@10 { compatible = "maxim,max98090"; @@ -440,8 +436,6 @@ &i2c_2 { status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&i2c2_bus>; }; &i2c_8 { From 00e5e8c47b6fb2da314b0221477b2b84bea0e224 Mon Sep 17 00:00:00 2001 From: Tobias Jakobi Date: Mon, 21 Sep 2015 19:59:00 +0200 Subject: [PATCH 13/22] ARM: dts: Unify voltage regulator style in exynos4412-odroid Use 'ldoN_reg: LDON' syntax and drop the deprecated 'regulator-compatible' property. Signed-off-by: Tobias Jakobi Reviewed-by: Javier Martinez Canillas Signed-off-by: Krzysztof Kozlowski --- arch/arm/boot/dts/exynos4412-odroid-common.dtsi | 6 ++---- 1 file changed, 2 insertions(+), 4 deletions(-) diff --git a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi index 10b5a72a8e4f..c3e978d77367 100644 --- a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi +++ b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi @@ -274,15 +274,13 @@ regulator-always-on; }; - ldo8_reg: ldo@8 { - regulator-compatible = "LDO8"; + ldo8_reg: LDO8 { regulator-name = "VDD10_HDMI_1.0V"; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1000000>; }; - ldo10_reg: ldo@10 { - regulator-compatible = "LDO10"; + ldo10_reg: LDO10 { regulator-name = "VDDQ_MIPIHSI_1.8V"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; From 6c6000c2ccfe69e5d17a2fba91954ce1e6f7df01 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Wed, 30 Sep 2015 15:53:55 +0900 Subject: [PATCH 14/22] ARM: dts: Add Exynos5250 Snow Rev5+ support on exynos5250-snow-rev5 There are 2 revisions of the Exynos5250 Snow Chromebook that were shipped: Rev4 and Rev5. The only difference between these 2 revisions is the codec, Rev4 has a max98095 codec while Rev5 has a max98090. Mainline only supports Rev4 so this patch moves the common device nodes to a DTSI file and adds a DTS for the Exynos5250 Snow Rev5. The Snow Rev5 DTS is based on the DTS found in the ChromiumOS 3.8 tree. Signed-off-by: Javier Martinez Canillas Tested-by: Mauro Carvalho Chehab Reviewed-by: Douglas Anderson Signed-off-by: Kukjin Kim --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/exynos5250-snow-common.dtsi | 684 ++++++++++++++++++ arch/arm/boot/dts/exynos5250-snow-rev5.dts | 47 ++ arch/arm/boot/dts/exynos5250-snow.dts | 671 +---------------- 4 files changed, 736 insertions(+), 667 deletions(-) create mode 100644 arch/arm/boot/dts/exynos5250-snow-common.dtsi create mode 100644 arch/arm/boot/dts/exynos5250-snow-rev5.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 3d27fe34647f..bc6649dcba5c 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -115,6 +115,7 @@ dtb-$(CONFIG_ARCH_EXYNOS5) += \ exynos5250-arndale.dtb \ exynos5250-smdk5250.dtb \ exynos5250-snow.dtb \ + exynos5250-snow-rev5.dtb \ exynos5250-spring.dtb \ exynos5260-xyref5260.dtb \ exynos5410-smdk5410.dtb \ diff --git a/arch/arm/boot/dts/exynos5250-snow-common.dtsi b/arch/arm/boot/dts/exynos5250-snow-common.dtsi new file mode 100644 index 000000000000..0a7f408824d8 --- /dev/null +++ b/arch/arm/boot/dts/exynos5250-snow-common.dtsi @@ -0,0 +1,684 @@ +/* + * Google Snow board device tree source + * + * Copyright (c) 2012 Google, Inc + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include +#include +#include +#include +#include "exynos5250.dtsi" + +/ { + aliases { + i2c104 = &i2c_104; + }; + + memory { + reg = <0x40000000 0x80000000>; + }; + + chosen { + bootargs = "console=tty1"; + stdout-path = "serial3:115200n8"; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&power_key_irq &lid_irq>; + + power { + label = "Power"; + gpios = <&gpx1 3 GPIO_ACTIVE_LOW>; + linux,code = ; + gpio-key,wakeup; + }; + + lid-switch { + label = "Lid"; + gpios = <&gpx3 5 GPIO_ACTIVE_LOW>; + linux,input-type = <5>; /* EV_SW */ + linux,code = <0>; /* SW_LID */ + debounce-interval = <1>; + gpio-key,wakeup; + }; + }; + + vbat: vbat-fixed-regulator { + compatible = "regulator-fixed"; + regulator-name = "vbat-supply"; + regulator-boot-on; + }; + + i2c-arbitrator { + compatible = "i2c-arb-gpio-challenge"; + #address-cells = <1>; + #size-cells = <0>; + + i2c-parent = <&{/i2c@12CA0000}>; + + our-claim-gpio = <&gpf0 3 GPIO_ACTIVE_LOW>; + their-claim-gpios = <&gpe0 4 GPIO_ACTIVE_LOW>; + slew-delay-us = <10>; + wait-retry-us = <3000>; + wait-free-us = <50000>; + + pinctrl-names = "default"; + pinctrl-0 = <&arb_our_claim &arb_their_claim>; + + /* Use ID 104 as a hint that we're on physical bus 4 */ + i2c_104: i2c@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + battery: sbs-battery@b { + compatible = "sbs,sbs-battery"; + reg = <0xb>; + sbs,poll-retry-count = <1>; + }; + + cros_ec: embedded-controller { + compatible = "google,cros-ec-i2c"; + reg = <0x1e>; + interrupts = <6 IRQ_TYPE_NONE>; + interrupt-parent = <&gpx1>; + pinctrl-names = "default"; + pinctrl-0 = <&ec_irq>; + wakeup-source; + }; + + power-regulator { + compatible = "ti,tps65090"; + reg = <0x48>; + + /* + * Config irq to disable internal pulls + * even though we run in polling mode. + */ + pinctrl-names = "default"; + pinctrl-0 = <&tps65090_irq>; + + vsys1-supply = <&vbat>; + vsys2-supply = <&vbat>; + vsys3-supply = <&vbat>; + infet1-supply = <&vbat>; + infet2-supply = <&vbat>; + infet3-supply = <&vbat>; + infet4-supply = <&vbat>; + infet5-supply = <&vbat>; + infet6-supply = <&vbat>; + infet7-supply = <&vbat>; + vsys-l1-supply = <&vbat>; + vsys-l2-supply = <&vbat>; + + regulators { + dcdc1 { + ti,enable-ext-control; + }; + dcdc2 { + ti,enable-ext-control; + }; + dcdc3 { + ti,enable-ext-control; + }; + fet1: fet1 { + regulator-name = "vcd_led"; + ti,overcurrent-wait = <3>; + }; + tps65090_fet2: fet2 { + regulator-name = "video_mid"; + regulator-always-on; + ti,overcurrent-wait = <3>; + }; + fet3 { + regulator-name = "wwan_r"; + regulator-always-on; + ti,overcurrent-wait = <3>; + }; + fet4 { + regulator-name = "sdcard"; + ti,overcurrent-wait = <3>; + }; + fet5 { + regulator-name = "camout"; + regulator-always-on; + ti,overcurrent-wait = <3>; + }; + fet6: fet6 { + regulator-name = "lcd_vdd"; + ti,overcurrent-wait = <3>; + }; + tps65090_fet7: fet7 { + regulator-name = "video_mid_1a"; + regulator-always-on; + ti,overcurrent-wait = <3>; + }; + ldo1 { + }; + ldo2 { + }; + }; + + charger { + compatible = "ti,tps65090-charger"; + }; + }; + }; + }; + + sound { + samsung,i2s-controller = <&i2s0>; + }; + + usb3_vbus_reg: regulator-usb3 { + compatible = "regulator-fixed"; + regulator-name = "P5.0V_USB3CON"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpx2 7 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&usb3_vbus_en>; + enable-active-high; + }; + + fixed-rate-clocks { + xxti { + compatible = "samsung,clock-xxti"; + clock-frequency = <24000000>; + }; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 0 1000000 0>; + brightness-levels = <0 100 500 1000 1500 2000 2500 2800>; + default-brightness-level = <7>; + enable-gpios = <&gpx3 0 GPIO_ACTIVE_HIGH>; + power-supply = <&fet1>; + pinctrl-0 = <&pwm0_out>; + pinctrl-names = "default"; + }; + + panel: panel { + compatible = "auo,b116xw03"; + power-supply = <&fet6>; + backlight = <&backlight>; + + port { + panel_in: endpoint { + remote-endpoint = <&bridge_out>; + }; + }; + }; + + mmc3_pwrseq: mmc3_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpx0 2 GPIO_ACTIVE_LOW>, /* WIFI_RSTn */ + <&gpx0 1 GPIO_ACTIVE_LOW>; /* WIFI_EN */ + clocks = <&max77686 MAX77686_CLK_PMIC>; + clock-names = "ext_clock"; + }; +}; + +&cpu0 { + cpu0-supply = <&buck2_reg>; +}; + +&dp { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&dp_hpd>; + samsung,color-space = <0>; + samsung,dynamic-range = <0>; + samsung,ycbcr-coeff = <0>; + samsung,color-depth = <1>; + samsung,link-rate = <0x0a>; + samsung,lane-count = <2>; + samsung,hpd-gpio = <&gpx0 7 GPIO_ACTIVE_HIGH>; + + ports { + port@0 { + dp_out: endpoint { + remote-endpoint = <&bridge_in>; + }; + }; + }; +}; + +&ehci { + samsung,vbus-gpio = <&gpx1 1 GPIO_ACTIVE_HIGH>; +}; + +&fimd { + status = "okay"; + samsung,invert-vclk; +}; + +&hdmi { + hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&hdmi_hpd_irq>; + phy = <&hdmiphy>; + ddc = <&i2c_2>; + hdmi-en-supply = <&tps65090_fet7>; + vdd-supply = <&ldo8_reg>; + vdd_osc-supply = <&ldo10_reg>; + vdd_pll-supply = <&ldo8_reg>; +}; + +&i2c_0 { + status = "okay"; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <378000>; + + max77686: max77686@09 { + compatible = "maxim,max77686"; + interrupt-parent = <&gpx3>; + interrupts = <2 IRQ_TYPE_NONE>; + pinctrl-names = "default"; + pinctrl-0 = <&max77686_irq>; + wakeup-source; + reg = <0x09>; + #clock-cells = <1>; + + voltage-regulators { + ldo1_reg: LDO1 { + regulator-name = "P1.0V_LDO_OUT1"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + ldo2_reg: LDO2 { + regulator-name = "P1.8V_LDO_OUT2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo3_reg: LDO3 { + regulator-name = "P1.8V_LDO_OUT3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo7_reg: LDO7 { + regulator-name = "P1.1V_LDO_OUT7"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + ldo8_reg: LDO8 { + regulator-name = "P1.0V_LDO_OUT8"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + ldo10_reg: LDO10 { + regulator-name = "P1.8V_LDO_OUT10"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo12_reg: LDO12 { + regulator-name = "P3.0V_LDO_OUT12"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + }; + + ldo14_reg: LDO14 { + regulator-name = "P1.8V_LDO_OUT14"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo15_reg: LDO15 { + regulator-name = "P1.0V_LDO_OUT15"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + ldo16_reg: LDO16 { + regulator-name = "P1.8V_LDO_OUT16"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + buck1_reg: BUCK1 { + regulator-name = "vdd_mif"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-boot-on; + }; + + buck2_reg: BUCK2 { + regulator-name = "vdd_arm"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + + buck3_reg: BUCK3 { + regulator-name = "vdd_int"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + }; + + buck4_reg: BUCK4 { + regulator-name = "vdd_g3d"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-boot-on; + }; + + buck5_reg: BUCK5 { + regulator-name = "P1.8V_BUCK_OUT5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + buck6_reg: BUCK6 { + regulator-name = "P1.35V_BUCK_OUT6"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + }; + + buck7_reg: BUCK7 { + regulator-name = "P2.0V_BUCK_OUT7"; + regulator-min-microvolt = <2000000>; + regulator-max-microvolt = <2000000>; + regulator-always-on; + }; + + buck8_reg: BUCK8 { + regulator-name = "P2.85V_BUCK_OUT8"; + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + regulator-always-on; + }; + }; + }; +}; + +&i2c_1 { + status = "okay"; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <378000>; + + trackpad { + reg = <0x67>; + compatible = "cypress,cyapa"; + interrupts = <2 IRQ_TYPE_NONE>; + interrupt-parent = <&gpx1>; + wakeup-source; + }; +}; + +/* + * Disabled pullups since external part has its own pullups and + * double-pulling gets us out of spec in some cases. + */ +&i2c2_bus { + samsung,pin-pud = <0>; +}; + +&i2c_2 { + status = "okay"; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <66000>; + + hdmiddc@50 { + compatible = "samsung,exynos4210-hdmiddc"; + reg = <0x50>; + }; +}; + +&i2c_3 { + status = "okay"; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <66000>; +}; + +&i2c_4 { + status = "okay"; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <66000>; +}; + +&i2c_5 { + status = "okay"; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <66000>; +}; + +&i2c_7 { + status = "okay"; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <66000>; + + ptn3460: lvds-bridge@20 { + compatible = "nxp,ptn3460"; + reg = <0x20>; + powerdown-gpios = <&gpy2 5 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpx1 5 GPIO_ACTIVE_HIGH>; + edid-emulation = <5>; + + ports { + port@0 { + bridge_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + + port@1 { + bridge_in: endpoint { + remote-endpoint = <&dp_out>; + }; + }; + }; + }; +}; + +&i2c_8 { + status = "okay"; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <378000>; + + hdmiphy: hdmiphy@38 { + compatible = "samsung,exynos4212-hdmiphy"; + reg = <0x38>; + }; +}; + +&i2s0 { + status = "okay"; +}; + +&mmc_0 { + status = "okay"; + num-slots = <1>; + broken-cd; + card-detect-delay = <200>; + samsung,dw-mshc-ciu-div = <3>; + samsung,dw-mshc-sdr-timing = <2 3>; + samsung,dw-mshc-ddr-timing = <1 2>; + pinctrl-names = "default"; + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_cd &sd0_bus4 &sd0_bus8>; + bus-width = <8>; + cap-mmc-highspeed; +}; + +&mmc_2 { + status = "okay"; + num-slots = <1>; + card-detect-delay = <200>; + samsung,dw-mshc-ciu-div = <3>; + samsung,dw-mshc-sdr-timing = <2 3>; + samsung,dw-mshc-ddr-timing = <1 2>; + pinctrl-names = "default"; + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; + bus-width = <4>; + wp-gpios = <&gpc2 1 GPIO_ACTIVE_HIGH>; + cap-sd-highspeed; +}; + +/* + * On Snow we've got SIP WiFi and so can keep drive strengths low to + * reduce EMI. + */ +&mmc_3 { + status = "okay"; + num-slots = <1>; + broken-cd; + cap-sdio-irq; + keep-power-in-suspend; + card-detect-delay = <200>; + samsung,dw-mshc-ciu-div = <3>; + samsung,dw-mshc-sdr-timing = <2 3>; + samsung,dw-mshc-ddr-timing = <1 2>; + pinctrl-names = "default"; + pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4 &wifi_en &wifi_rst>; + bus-width = <4>; + cap-sd-highspeed; + mmc-pwrseq = <&mmc3_pwrseq>; +}; + +&pinctrl_0 { + wifi_en: wifi-en { + samsung,pins = "gpx0-1"; + samsung,pin-function = <1>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + wifi_rst: wifi-rst { + samsung,pins = "gpx0-2"; + samsung,pin-function = <1>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + power_key_irq: power-key-irq { + samsung,pins = "gpx1-3"; + samsung,pin-function = <0xf>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + ec_irq: ec-irq { + samsung,pins = "gpx1-6"; + samsung,pin-function = <0>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + tps65090_irq: tps65090-irq { + samsung,pins = "gpx2-6"; + samsung,pin-function = <0>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + usb3_vbus_en: usb3-vbus-en { + samsung,pins = "gpx2-7"; + samsung,pin-function = <1>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + max77686_irq: max77686-irq { + samsung,pins = "gpx3-2"; + samsung,pin-function = <0>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + lid_irq: lid-irq { + samsung,pins = "gpx3-5"; + samsung,pin-function = <0xf>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + hdmi_hpd_irq: hdmi-hpd-irq { + samsung,pins = "gpx3-7"; + samsung,pin-function = <0>; + samsung,pin-pud = <1>; + samsung,pin-drv = <0>; + }; +}; + +&pinctrl_1 { + arb_their_claim: arb-their-claim { + samsung,pins = "gpe0-4"; + samsung,pin-function = <0>; + samsung,pin-pud = <3>; + samsung,pin-drv = <0>; + }; + + arb_our_claim: arb-our-claim { + samsung,pins = "gpf0-3"; + samsung,pin-function = <1>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; +}; + +&rtc { + status = "okay"; + clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>; + clock-names = "rtc", "rtc_src"; +}; + +&sd3_bus4 { + samsung,pin-drv = <0>; +}; + +&sd3_clk { + samsung,pin-drv = <0>; +}; + +&sd3_cmd { + samsung,pin-pud = <3>; + samsung,pin-drv = <0>; +}; + +&spi_1 { + status = "okay"; + samsung,spi-src-clk = <0>; + num-cs = <1>; + cs-gpios = <&gpa2 5 GPIO_ACTIVE_HIGH>; +}; + +&usbdrd_dwc3 { + dr_mode = "host"; +}; + +&usbdrd_phy { + vbus-supply = <&usb3_vbus_reg>; +}; + +#include "cros-ec-keyboard.dtsi" diff --git a/arch/arm/boot/dts/exynos5250-snow-rev5.dts b/arch/arm/boot/dts/exynos5250-snow-rev5.dts new file mode 100644 index 000000000000..f811dc800660 --- /dev/null +++ b/arch/arm/boot/dts/exynos5250-snow-rev5.dts @@ -0,0 +1,47 @@ +/* + * Google Snow Rev 5+ board device tree source + * + * Copyright (c) 2012 Google, Inc + * Copyright (c) 2015 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; +#include "exynos5250-snow-common.dtsi" + +/ { + model = "Google Snow Rev 5+"; + compatible = "google,snow-rev5", "samsung,exynos5250", + "samsung,exynos5"; + + sound { + compatible = "google,snow-audio-max98090"; + + samsung,model = "Snow-I2S-MAX98090"; + samsung,audio-codec = <&max98090>; + }; +}; + +&i2c_7 { + max98090: codec@10 { + compatible = "maxim,max98090"; + reg = <0x10>; + interrupts = <4 IRQ_TYPE_NONE>; + interrupt-parent = <&gpx0>; + pinctrl-names = "default"; + pinctrl-0 = <&max98090_irq>; + }; +}; + +&pinctrl_0 { + max98090_irq: max98090-irq { + samsung,pins = "gpx0-4"; + samsung,pin-function = <0>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; +}; diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts index 0720caab5511..995c7ce6c12b 100644 --- a/arch/arm/boot/dts/exynos5250-snow.dts +++ b/arch/arm/boot/dts/exynos5250-snow.dts @@ -9,698 +9,35 @@ */ /dts-v1/; -#include -#include -#include -#include -#include "exynos5250.dtsi" +#include "exynos5250-snow-common.dtsi" / { model = "Google Snow"; - compatible = "google,snow", "samsung,exynos5250", "samsung,exynos5"; - - aliases { - i2c104 = &i2c_104; - }; - - memory { - reg = <0x40000000 0x80000000>; - }; - - chosen { - bootargs = "console=tty1"; - stdout-path = "serial3:115200n8"; - }; - - gpio-keys { - compatible = "gpio-keys"; - pinctrl-names = "default"; - pinctrl-0 = <&power_key_irq &lid_irq>; - - power { - label = "Power"; - gpios = <&gpx1 3 GPIO_ACTIVE_LOW>; - linux,code = ; - gpio-key,wakeup; - }; - - lid-switch { - label = "Lid"; - gpios = <&gpx3 5 GPIO_ACTIVE_LOW>; - linux,input-type = <5>; /* EV_SW */ - linux,code = <0>; /* SW_LID */ - debounce-interval = <1>; - gpio-key,wakeup; - }; - }; - - vbat: vbat-fixed-regulator { - compatible = "regulator-fixed"; - regulator-name = "vbat-supply"; - regulator-boot-on; - }; - - i2c-arbitrator { - compatible = "i2c-arb-gpio-challenge"; - #address-cells = <1>; - #size-cells = <0>; - - i2c-parent = <&{/i2c@12CA0000}>; - - our-claim-gpio = <&gpf0 3 GPIO_ACTIVE_LOW>; - their-claim-gpios = <&gpe0 4 GPIO_ACTIVE_LOW>; - slew-delay-us = <10>; - wait-retry-us = <3000>; - wait-free-us = <50000>; - - pinctrl-names = "default"; - pinctrl-0 = <&arb_our_claim &arb_their_claim>; - - /* Use ID 104 as a hint that we're on physical bus 4 */ - i2c_104: i2c@0 { - reg = <0>; - #address-cells = <1>; - #size-cells = <0>; - - battery: sbs-battery@b { - compatible = "sbs,sbs-battery"; - reg = <0xb>; - sbs,poll-retry-count = <1>; - }; - - cros_ec: embedded-controller { - compatible = "google,cros-ec-i2c"; - reg = <0x1e>; - interrupts = <6 IRQ_TYPE_NONE>; - interrupt-parent = <&gpx1>; - pinctrl-names = "default"; - pinctrl-0 = <&ec_irq>; - wakeup-source; - }; - - power-regulator { - compatible = "ti,tps65090"; - reg = <0x48>; - - /* - * Config irq to disable internal pulls - * even though we run in polling mode. - */ - pinctrl-names = "default"; - pinctrl-0 = <&tps65090_irq>; - - vsys1-supply = <&vbat>; - vsys2-supply = <&vbat>; - vsys3-supply = <&vbat>; - infet1-supply = <&vbat>; - infet2-supply = <&vbat>; - infet3-supply = <&vbat>; - infet4-supply = <&vbat>; - infet5-supply = <&vbat>; - infet6-supply = <&vbat>; - infet7-supply = <&vbat>; - vsys-l1-supply = <&vbat>; - vsys-l2-supply = <&vbat>; - - regulators { - dcdc1 { - ti,enable-ext-control; - }; - dcdc2 { - ti,enable-ext-control; - }; - dcdc3 { - ti,enable-ext-control; - }; - fet1: fet1 { - regulator-name = "vcd_led"; - ti,overcurrent-wait = <3>; - }; - tps65090_fet2: fet2 { - regulator-name = "video_mid"; - regulator-always-on; - ti,overcurrent-wait = <3>; - }; - fet3 { - regulator-name = "wwan_r"; - regulator-always-on; - ti,overcurrent-wait = <3>; - }; - fet4 { - regulator-name = "sdcard"; - ti,overcurrent-wait = <3>; - }; - fet5 { - regulator-name = "camout"; - regulator-always-on; - ti,overcurrent-wait = <3>; - }; - fet6: fet6 { - regulator-name = "lcd_vdd"; - ti,overcurrent-wait = <3>; - }; - tps65090_fet7: fet7 { - regulator-name = "video_mid_1a"; - regulator-always-on; - ti,overcurrent-wait = <3>; - }; - ldo1 { - }; - ldo2 { - }; - }; - - charger { - compatible = "ti,tps65090-charger"; - }; - }; - }; - }; + compatible = "google,snow-rev4", "google,snow", "samsung,exynos5250", + "samsung,exynos5"; sound { compatible = "google,snow-audio-max98095"; samsung,model = "Snow-I2S-MAX98095"; - samsung,i2s-controller = <&i2s0>; samsung,audio-codec = <&max98095>; }; - - usb3_vbus_reg: regulator-usb3 { - compatible = "regulator-fixed"; - regulator-name = "P5.0V_USB3CON"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - gpio = <&gpx2 7 GPIO_ACTIVE_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&usb3_vbus_en>; - enable-active-high; - }; - - fixed-rate-clocks { - xxti { - compatible = "samsung,clock-xxti"; - clock-frequency = <24000000>; - }; - }; - - backlight: backlight { - compatible = "pwm-backlight"; - pwms = <&pwm 0 1000000 0>; - brightness-levels = <0 100 500 1000 1500 2000 2500 2800>; - default-brightness-level = <7>; - enable-gpios = <&gpx3 0 GPIO_ACTIVE_HIGH>; - power-supply = <&fet1>; - pinctrl-0 = <&pwm0_out>; - pinctrl-names = "default"; - }; - - panel: panel { - compatible = "auo,b116xw03"; - power-supply = <&fet6>; - backlight = <&backlight>; - - port { - panel_in: endpoint { - remote-endpoint = <&bridge_out>; - }; - }; - }; - - mmc3_pwrseq: mmc3_pwrseq { - compatible = "mmc-pwrseq-simple"; - reset-gpios = <&gpx0 2 GPIO_ACTIVE_LOW>, /* WIFI_RSTn */ - <&gpx0 1 GPIO_ACTIVE_LOW>; /* WIFI_EN */ - clocks = <&max77686 MAX77686_CLK_PMIC>; - clock-names = "ext_clock"; - }; -}; - -&cpu0 { - cpu0-supply = <&buck2_reg>; -}; - -&dp { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&dp_hpd>; - samsung,color-space = <0>; - samsung,dynamic-range = <0>; - samsung,ycbcr-coeff = <0>; - samsung,color-depth = <1>; - samsung,link-rate = <0x0a>; - samsung,lane-count = <2>; - samsung,hpd-gpio = <&gpx0 7 GPIO_ACTIVE_HIGH>; - - ports { - port@0 { - dp_out: endpoint { - remote-endpoint = <&bridge_in>; - }; - }; - }; -}; - -&ehci { - samsung,vbus-gpio = <&gpx1 1 GPIO_ACTIVE_HIGH>; -}; - -&fimd { - status = "okay"; - samsung,invert-vclk; -}; - -&hdmi { - hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&hdmi_hpd_irq>; - phy = <&hdmiphy>; - ddc = <&i2c_2>; - hdmi-en-supply = <&tps65090_fet7>; - vdd-supply = <&ldo8_reg>; - vdd_osc-supply = <&ldo10_reg>; - vdd_pll-supply = <&ldo8_reg>; -}; - -&i2c_0 { - status = "okay"; - samsung,i2c-sda-delay = <100>; - samsung,i2c-max-bus-freq = <378000>; - - max77686: max77686@09 { - compatible = "maxim,max77686"; - interrupt-parent = <&gpx3>; - interrupts = <2 IRQ_TYPE_NONE>; - pinctrl-names = "default"; - pinctrl-0 = <&max77686_irq>; - wakeup-source; - reg = <0x09>; - #clock-cells = <1>; - - voltage-regulators { - ldo1_reg: LDO1 { - regulator-name = "P1.0V_LDO_OUT1"; - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <1000000>; - regulator-always-on; - }; - - ldo2_reg: LDO2 { - regulator-name = "P1.8V_LDO_OUT2"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - }; - - ldo3_reg: LDO3 { - regulator-name = "P1.8V_LDO_OUT3"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - }; - - ldo7_reg: LDO7 { - regulator-name = "P1.1V_LDO_OUT7"; - regulator-min-microvolt = <1100000>; - regulator-max-microvolt = <1100000>; - regulator-always-on; - }; - - ldo8_reg: LDO8 { - regulator-name = "P1.0V_LDO_OUT8"; - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <1000000>; - regulator-always-on; - }; - - ldo10_reg: LDO10 { - regulator-name = "P1.8V_LDO_OUT10"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - }; - - ldo12_reg: LDO12 { - regulator-name = "P3.0V_LDO_OUT12"; - regulator-min-microvolt = <3000000>; - regulator-max-microvolt = <3000000>; - regulator-always-on; - }; - - ldo14_reg: LDO14 { - regulator-name = "P1.8V_LDO_OUT14"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - }; - - ldo15_reg: LDO15 { - regulator-name = "P1.0V_LDO_OUT15"; - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <1000000>; - regulator-always-on; - }; - - ldo16_reg: LDO16 { - regulator-name = "P1.8V_LDO_OUT16"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - }; - - buck1_reg: BUCK1 { - regulator-name = "vdd_mif"; - regulator-min-microvolt = <950000>; - regulator-max-microvolt = <1300000>; - regulator-always-on; - regulator-boot-on; - }; - - buck2_reg: BUCK2 { - regulator-name = "vdd_arm"; - regulator-min-microvolt = <850000>; - regulator-max-microvolt = <1350000>; - regulator-always-on; - regulator-boot-on; - }; - - buck3_reg: BUCK3 { - regulator-name = "vdd_int"; - regulator-min-microvolt = <900000>; - regulator-max-microvolt = <1200000>; - regulator-always-on; - regulator-boot-on; - }; - - buck4_reg: BUCK4 { - regulator-name = "vdd_g3d"; - regulator-min-microvolt = <850000>; - regulator-max-microvolt = <1300000>; - regulator-always-on; - regulator-boot-on; - }; - - buck5_reg: BUCK5 { - regulator-name = "P1.8V_BUCK_OUT5"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - regulator-boot-on; - }; - - buck6_reg: BUCK6 { - regulator-name = "P1.35V_BUCK_OUT6"; - regulator-min-microvolt = <1350000>; - regulator-max-microvolt = <1350000>; - regulator-always-on; - }; - - buck7_reg: BUCK7 { - regulator-name = "P2.0V_BUCK_OUT7"; - regulator-min-microvolt = <2000000>; - regulator-max-microvolt = <2000000>; - regulator-always-on; - }; - - buck8_reg: BUCK8 { - regulator-name = "P2.85V_BUCK_OUT8"; - regulator-min-microvolt = <2850000>; - regulator-max-microvolt = <2850000>; - regulator-always-on; - }; - }; - }; -}; - -&i2c_1 { - status = "okay"; - samsung,i2c-sda-delay = <100>; - samsung,i2c-max-bus-freq = <378000>; - - trackpad { - reg = <0x67>; - compatible = "cypress,cyapa"; - interrupts = <2 IRQ_TYPE_NONE>; - interrupt-parent = <&gpx1>; - wakeup-source; - }; -}; - -/* - * Disabled pullups since external part has its own pullups and - * double-pulling gets us out of spec in some cases. - */ -&i2c2_bus { - samsung,pin-pud = <0>; -}; - -&i2c_2 { - status = "okay"; - samsung,i2c-sda-delay = <100>; - samsung,i2c-max-bus-freq = <66000>; - - hdmiddc@50 { - compatible = "samsung,exynos4210-hdmiddc"; - reg = <0x50>; - }; -}; - -&i2c_3 { - status = "okay"; - samsung,i2c-sda-delay = <100>; - samsung,i2c-max-bus-freq = <66000>; -}; - -&i2c_4 { - status = "okay"; - samsung,i2c-sda-delay = <100>; - samsung,i2c-max-bus-freq = <66000>; -}; - -&i2c_5 { - status = "okay"; - samsung,i2c-sda-delay = <100>; - samsung,i2c-max-bus-freq = <66000>; }; &i2c_7 { - status = "okay"; - samsung,i2c-sda-delay = <100>; - samsung,i2c-max-bus-freq = <66000>; - - ptn3460: lvds-bridge@20 { - compatible = "nxp,ptn3460"; - reg = <0x20>; - powerdown-gpios = <&gpy2 5 GPIO_ACTIVE_HIGH>; - reset-gpios = <&gpx1 5 GPIO_ACTIVE_HIGH>; - edid-emulation = <5>; - - ports { - port@0 { - bridge_out: endpoint { - remote-endpoint = <&panel_in>; - }; - }; - - port@1 { - bridge_in: endpoint { - remote-endpoint = <&dp_out>; - }; - }; - }; - }; - max98095: codec@11 { compatible = "maxim,max98095"; reg = <0x11>; - pinctrl-0 = <&max98095_en>; pinctrl-names = "default"; + pinctrl-0 = <&max98095_en>; }; }; -&i2c_8 { - status = "okay"; - samsung,i2c-sda-delay = <100>; - samsung,i2c-max-bus-freq = <378000>; - - hdmiphy: hdmiphy@38 { - compatible = "samsung,exynos4212-hdmiphy"; - reg = <0x38>; - }; -}; - -&i2s0 { - status = "okay"; -}; - -&mmc_0 { - status = "okay"; - num-slots = <1>; - broken-cd; - card-detect-delay = <200>; - samsung,dw-mshc-ciu-div = <3>; - samsung,dw-mshc-sdr-timing = <2 3>; - samsung,dw-mshc-ddr-timing = <1 2>; - pinctrl-names = "default"; - pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_cd &sd0_bus4 &sd0_bus8>; - bus-width = <8>; - cap-mmc-highspeed; -}; - -&mmc_2 { - status = "okay"; - num-slots = <1>; - card-detect-delay = <200>; - samsung,dw-mshc-ciu-div = <3>; - samsung,dw-mshc-sdr-timing = <2 3>; - samsung,dw-mshc-ddr-timing = <1 2>; - pinctrl-names = "default"; - pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; - bus-width = <4>; - wp-gpios = <&gpc2 1 GPIO_ACTIVE_HIGH>; - cap-sd-highspeed; -}; - -/* - * On Snow we've got SIP WiFi and so can keep drive strengths low to - * reduce EMI. - */ -&mmc_3 { - status = "okay"; - num-slots = <1>; - broken-cd; - cap-sdio-irq; - keep-power-in-suspend; - card-detect-delay = <200>; - samsung,dw-mshc-ciu-div = <3>; - samsung,dw-mshc-sdr-timing = <2 3>; - samsung,dw-mshc-ddr-timing = <1 2>; - pinctrl-names = "default"; - pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4 &wifi_en &wifi_rst>; - bus-width = <4>; - cap-sd-highspeed; - mmc-pwrseq = <&mmc3_pwrseq>; -}; - &pinctrl_0 { - wifi_en: wifi-en { - samsung,pins = "gpx0-1"; - samsung,pin-function = <1>; - samsung,pin-pud = <0>; - samsung,pin-drv = <0>; - }; - - wifi_rst: wifi-rst { - samsung,pins = "gpx0-2"; - samsung,pin-function = <1>; - samsung,pin-pud = <0>; - samsung,pin-drv = <0>; - }; - - power_key_irq: power-key-irq { - samsung,pins = "gpx1-3"; - samsung,pin-function = <0xf>; - samsung,pin-pud = <0>; - samsung,pin-drv = <0>; - }; - - ec_irq: ec-irq { - samsung,pins = "gpx1-6"; - samsung,pin-function = <0>; - samsung,pin-pud = <0>; - samsung,pin-drv = <0>; - }; - max98095_en: max98095-en { samsung,pins = "gpx1-7"; samsung,pin-function = <0>; samsung,pin-pud = <3>; samsung,pin-drv = <0>; }; - - tps65090_irq: tps65090-irq { - samsung,pins = "gpx2-6"; - samsung,pin-function = <0>; - samsung,pin-pud = <0>; - samsung,pin-drv = <0>; - }; - - usb3_vbus_en: usb3-vbus-en { - samsung,pins = "gpx2-7"; - samsung,pin-function = <1>; - samsung,pin-pud = <0>; - samsung,pin-drv = <0>; - }; - - max77686_irq: max77686-irq { - samsung,pins = "gpx3-2"; - samsung,pin-function = <0>; - samsung,pin-pud = <0>; - samsung,pin-drv = <0>; - }; - - lid_irq: lid-irq { - samsung,pins = "gpx3-5"; - samsung,pin-function = <0xf>; - samsung,pin-pud = <0>; - samsung,pin-drv = <0>; - }; - - hdmi_hpd_irq: hdmi-hpd-irq { - samsung,pins = "gpx3-7"; - samsung,pin-function = <0>; - samsung,pin-pud = <1>; - samsung,pin-drv = <0>; - }; }; - -&pinctrl_1 { - arb_their_claim: arb-their-claim { - samsung,pins = "gpe0-4"; - samsung,pin-function = <0>; - samsung,pin-pud = <3>; - samsung,pin-drv = <0>; - }; - - arb_our_claim: arb-our-claim { - samsung,pins = "gpf0-3"; - samsung,pin-function = <1>; - samsung,pin-pud = <0>; - samsung,pin-drv = <0>; - }; -}; - -&rtc { - status = "okay"; - clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>; - clock-names = "rtc", "rtc_src"; -}; - -&sd3_bus4 { - samsung,pin-drv = <0>; -}; - -&sd3_clk { - samsung,pin-drv = <0>; -}; - -&sd3_cmd { - samsung,pin-pud = <3>; - samsung,pin-drv = <0>; -}; - -&spi_1 { - status = "okay"; - samsung,spi-src-clk = <0>; - num-cs = <1>; - cs-gpios = <&gpa2 5 GPIO_ACTIVE_HIGH>; -}; - -&usbdrd_dwc3 { - dr_mode = "host"; -}; - -&usbdrd_phy { - vbus-supply = <&usb3_vbus_reg>; -}; - -#include "cros-ec-keyboard.dtsi" From c5185068066d854dab2f1af1894cd994234c65ce Mon Sep 17 00:00:00 2001 From: Sean Paul Date: Thu, 17 Sep 2015 14:48:39 +0200 Subject: [PATCH 15/22] ARM: dts: Move display-timings node from fimd to dp in exynos5250-arndale, smdk5250 and smdk5420 This patch moves the display-timings node from fimd to dp to reflect the device tree bindings change. Signed-off-by: Sean Paul [tomeu.vizoso@collabora.com: Rebased] Signed-off-by: Tomeu Vizoso Signed-off-by: Krzysztof Kozlowski --- arch/arm/boot/dts/exynos5250-arndale.dts | 8 ++++---- arch/arm/boot/dts/exynos5250-smdk5250.dts | 16 ++++++++-------- arch/arm/boot/dts/exynos5420-smdk5420.dts | 7 ++++--- 3 files changed, 16 insertions(+), 15 deletions(-) diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts index db3f65f3eb45..c000532c1444 100644 --- a/arch/arm/boot/dts/exynos5250-arndale.dts +++ b/arch/arm/boot/dts/exynos5250-arndale.dts @@ -129,10 +129,6 @@ samsung,color-depth = <1>; samsung,link-rate = <0x0a>; samsung,lane-count = <4>; -}; - -&fimd { - status = "okay"; display-timings { native-mode = <&timing0>; @@ -152,6 +148,10 @@ }; }; +&fimd { + status = "okay"; +}; + &hdmi { hpd-gpio = <&gpx3 7 GPIO_ACTIVE_LOW>; vdd_osc-supply = <&ldo10_reg>; diff --git a/arch/arm/boot/dts/exynos5250-smdk5250.dts b/arch/arm/boot/dts/exynos5250-smdk5250.dts index 15aea760c1da..66da0d1d9d8a 100644 --- a/arch/arm/boot/dts/exynos5250-smdk5250.dts +++ b/arch/arm/boot/dts/exynos5250-smdk5250.dts @@ -89,14 +89,6 @@ pinctrl-names = "default"; pinctrl-0 = <&dp_hpd>; status = "okay"; -}; - -&ehci { - samsung,vbus-gpio = <&gpx2 6 GPIO_ACTIVE_HIGH>; -}; - -&fimd { - status = "okay"; display-timings { native-mode = <&timing0>; @@ -116,6 +108,14 @@ }; }; +&ehci { + samsung,vbus-gpio = <&gpx2 6 GPIO_ACTIVE_HIGH>; +}; + +&fimd { + status = "okay"; +}; + &hdmi { hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>; }; diff --git a/arch/arm/boot/dts/exynos5420-smdk5420.dts b/arch/arm/boot/dts/exynos5420-smdk5420.dts index 98871f972c8a..7520d52f4e22 100644 --- a/arch/arm/boot/dts/exynos5420-smdk5420.dts +++ b/arch/arm/boot/dts/exynos5420-smdk5420.dts @@ -98,10 +98,7 @@ samsung,link-rate = <0x0a>; samsung,lane-count = <4>; status = "okay"; -}; -&fimd { - status = "okay"; display-timings { native-mode = <&timing0>; timing0: timing@0 { @@ -118,6 +115,10 @@ }; }; +&fimd { + status = "okay"; +}; + &hdmi { status = "okay"; hpd-gpio = <&gpx3 7 0>; From c21dbcfefc9dc9abc42971dc1f2681b6a8677c3c Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Mon, 28 Sep 2015 12:38:34 +0200 Subject: [PATCH 16/22] ARM: dts: Remove regulator-compatible usage in exynos4412-trats2 The regulator-compatible property from the regulator DT binding was deprecated and the correct approach is to use the node's name. This patch has no functional changes but by not using a deprecated property, new DTS based on this one will not carry the same issue. Signed-off-by: Javier Martinez Canillas Signed-off-by: Krzysztof Kozlowski --- arch/arm/boot/dts/exynos4412-trats2.dts | 105 ++++++++---------------- 1 file changed, 35 insertions(+), 70 deletions(-) diff --git a/arch/arm/boot/dts/exynos4412-trats2.dts b/arch/arm/boot/dts/exynos4412-trats2.dts index 2a1ebb76ebe0..93e3bbd4bd49 100644 --- a/arch/arm/boot/dts/exynos4412-trats2.dts +++ b/arch/arm/boot/dts/exynos4412-trats2.dts @@ -564,16 +564,14 @@ #clock-cells = <1>; voltage-regulators { - ldo1_reg: ldo1 { - regulator-compatible = "LDO1"; + ldo1_reg: LDO1 { regulator-name = "VALIVE_1.0V_AP"; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1000000>; regulator-always-on; }; - ldo2_reg: ldo2 { - regulator-compatible = "LDO2"; + ldo2_reg: LDO2 { regulator-name = "VM1M2_1.2V_AP"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; @@ -583,32 +581,28 @@ }; }; - ldo3_reg: ldo3 { - regulator-compatible = "LDO3"; + ldo3_reg: LDO3 { regulator-name = "VCC_1.8V_AP"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; regulator-always-on; }; - ldo4_reg: ldo4 { - regulator-compatible = "LDO4"; + ldo4_reg: LDO4 { regulator-name = "VCC_2.8V_AP"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; regulator-always-on; }; - ldo5_reg: ldo5 { - regulator-compatible = "LDO5"; + ldo5_reg: LDO5 { regulator-name = "VCC_1.8V_IO"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; regulator-always-on; }; - ldo6_reg: ldo6 { - regulator-compatible = "LDO6"; + ldo6_reg: LDO6 { regulator-name = "VMPLL_1.0V_AP"; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1000000>; @@ -618,8 +612,7 @@ }; }; - ldo7_reg: ldo7 { - regulator-compatible = "LDO7"; + ldo7_reg: LDO7 { regulator-name = "VPLL_1.0V_AP"; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1000000>; @@ -629,8 +622,7 @@ }; }; - ldo8_reg: ldo8 { - regulator-compatible = "LDO8"; + ldo8_reg: LDO8 { regulator-name = "VMIPI_1.0V"; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1000000>; @@ -639,15 +631,13 @@ }; }; - ldo9_reg: ldo9 { - regulator-compatible = "LDO9"; + ldo9_reg: LDO9 { regulator-name = "CAM_ISP_MIPI_1.2V"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; }; - ldo10_reg: ldo10 { - regulator-compatible = "LDO10"; + ldo10_reg: LDO10 { regulator-name = "VMIPI_1.8V"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; @@ -656,8 +646,7 @@ }; }; - ldo11_reg: ldo11 { - regulator-compatible = "LDO11"; + ldo11_reg: LDO11 { regulator-name = "VABB1_1.95V"; regulator-min-microvolt = <1950000>; regulator-max-microvolt = <1950000>; @@ -667,8 +656,7 @@ }; }; - ldo12_reg: ldo12 { - regulator-compatible = "LDO12"; + ldo12_reg: LDO12 { regulator-name = "VUOTG_3.0V"; regulator-min-microvolt = <3000000>; regulator-max-microvolt = <3000000>; @@ -677,15 +665,13 @@ }; }; - ldo13_reg: ldo13 { - regulator-compatible = "LDO13"; + ldo13_reg: LDO13 { regulator-name = "NFC_AVDD_1.8V"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; }; - ldo14_reg: ldo14 { - regulator-compatible = "LDO14"; + ldo14_reg: LDO14 { regulator-name = "VABB2_1.95V"; regulator-min-microvolt = <1950000>; regulator-max-microvolt = <1950000>; @@ -695,8 +681,7 @@ }; }; - ldo15_reg: ldo15 { - regulator-compatible = "LDO15"; + ldo15_reg: LDO15 { regulator-name = "VHSIC_1.0V"; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1000000>; @@ -705,8 +690,7 @@ }; }; - ldo16_reg: ldo16 { - regulator-compatible = "LDO16"; + ldo16_reg: LDO16 { regulator-name = "VHSIC_1.8V"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; @@ -715,80 +699,69 @@ }; }; - ldo17_reg: ldo17 { - regulator-compatible = "LDO17"; + ldo17_reg: LDO17 { regulator-name = "CAM_SENSOR_CORE_1.2V"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; }; - ldo18_reg: ldo18 { - regulator-compatible = "LDO18"; + ldo18_reg: LDO18 { regulator-name = "CAM_ISP_SEN_IO_1.8V"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; }; - ldo19_reg: ldo19 { - regulator-compatible = "LDO19"; + ldo19_reg: LDO19 { regulator-name = "VT_CAM_1.8V"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; }; - ldo20_reg: ldo20 { - regulator-compatible = "LDO20"; + ldo20_reg: LDO20 { regulator-name = "VDDQ_PRE_1.8V"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; }; - ldo21_reg: ldo21 { - regulator-compatible = "LDO21"; + ldo21_reg: LDO21 { regulator-name = "VTF_2.8V"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; maxim,ena-gpios = <&gpy2 0 GPIO_ACTIVE_HIGH>; }; - ldo22_reg: ldo22 { - regulator-compatible = "LDO22"; + ldo22_reg: LDO22 { regulator-name = "VMEM_VDD_2.8V"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; maxim,ena-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>; }; - ldo23_reg: ldo23 { - regulator-compatible = "LDO23"; + ldo23_reg: LDO23 { regulator-name = "TSP_AVDD_3.3V"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; }; - ldo24_reg: ldo24 { - regulator-compatible = "LDO24"; + ldo24_reg: LDO24 { regulator-name = "TSP_VDD_1.8V"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; }; - ldo25_reg: ldo25 { - regulator-compatible = "LDO25"; + ldo25_reg: LDO25 { regulator-name = "LCD_VCC_3.3V"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; }; - ldo26_reg: ldo26 { - regulator-compatible = "LDO26"; + ldo26_reg: LDO26 { regulator-name = "MOTOR_VCC_3.0V"; regulator-min-microvolt = <3000000>; regulator-max-microvolt = <3000000>; }; - buck1_reg: buck1 { - regulator-compatible = "BUCK1"; + buck1_reg: BUCK1 { regulator-name = "vdd_mif"; regulator-min-microvolt = <850000>; regulator-max-microvolt = <1100000>; @@ -799,8 +772,7 @@ }; }; - buck2_reg: buck2 { - regulator-compatible = "BUCK2"; + buck2_reg: BUCK2 { regulator-name = "vdd_arm"; regulator-min-microvolt = <850000>; regulator-max-microvolt = <1500000>; @@ -811,8 +783,7 @@ }; }; - buck3_reg: buck3 { - regulator-compatible = "BUCK3"; + buck3_reg: BUCK3 { regulator-name = "vdd_int"; regulator-min-microvolt = <850000>; regulator-max-microvolt = <1150000>; @@ -823,8 +794,7 @@ }; }; - buck4_reg: buck4 { - regulator-compatible = "BUCK4"; + buck4_reg: BUCK4 { regulator-name = "vdd_g3d"; regulator-min-microvolt = <850000>; regulator-max-microvolt = <1150000>; @@ -834,40 +804,35 @@ }; }; - buck5_reg: buck5 { - regulator-compatible = "BUCK5"; + buck5_reg: BUCK5 { regulator-name = "VMEM_1.2V_AP"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; regulator-always-on; }; - buck6_reg: buck6 { - regulator-compatible = "BUCK6"; + buck6_reg: BUCK6 { regulator-name = "VCC_SUB_1.35V"; regulator-min-microvolt = <1350000>; regulator-max-microvolt = <1350000>; regulator-always-on; }; - buck7_reg: buck7 { - regulator-compatible = "BUCK7"; + buck7_reg: BUCK7 { regulator-name = "VCC_SUB_2.0V"; regulator-min-microvolt = <2000000>; regulator-max-microvolt = <2000000>; regulator-always-on; }; - buck8_reg: buck8 { - regulator-compatible = "BUCK8"; + buck8_reg: BUCK8 { regulator-name = "VMEM_VDDF_3.0V"; regulator-min-microvolt = <2850000>; regulator-max-microvolt = <2850000>; maxim,ena-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>; }; - buck9_reg: buck9 { - regulator-compatible = "BUCK9"; + buck9_reg: BUCK9 { regulator-name = "CAM_ISP_CORE_1.2V"; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1200000>; From 27e6699c35be9a849e35d58f381efc199a1e1ede Mon Sep 17 00:00:00 2001 From: Emilio Lopez Date: Thu, 8 Oct 2015 07:35:21 +0900 Subject: [PATCH 17/22] ARM: dts: Enable EC vboot context support on Peach boards The Peach boards use the EC to store the vboot context information, so add the corresponding properties on the EC node to indicate so. Reviewed-by: Krzysztof Kozlowski Acked-by: Javier Martinez Canillas Signed-off-by: Emilio Lopez Signed-off-by: Kukjin Kim --- arch/arm/boot/dts/exynos5420-peach-pit.dts | 1 + arch/arm/boot/dts/exynos5800-peach-pi.dts | 1 + 2 files changed, 2 insertions(+) diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/exynos5420-peach-pit.dts index 8f4d76c5e11c..ac02fb42ac0c 100644 --- a/arch/arm/boot/dts/exynos5420-peach-pit.dts +++ b/arch/arm/boot/dts/exynos5420-peach-pit.dts @@ -935,6 +935,7 @@ pinctrl-0 = <&ec_spi_cs &ec_irq>; reg = <0>; spi-max-frequency = <3125000>; + google,has-vbc-nvram; controller-data { samsung,spi-feedback-delay = <1>; diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts index 7d5b386b5ae6..b60dec0f1f67 100644 --- a/arch/arm/boot/dts/exynos5800-peach-pi.dts +++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts @@ -898,6 +898,7 @@ pinctrl-0 = <&ec_spi_cs &ec_irq>; reg = <0>; spi-max-frequency = <3125000>; + google,has-vbc-nvram; controller-data { samsung,spi-feedback-delay = <1>; From de77e52d34269f25a33e231fe3c1431116776617 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Thu, 8 Oct 2015 07:39:57 +0900 Subject: [PATCH 18/22] ARM: dts: Use GPIO constants for flags cells in exynos3250 boards The board DTS are using numeric values instead of the defined GPIO constanst to express polarity, use them to make the DTS more clear. Signed-off-by: Javier Martinez Canillas Signed-off-by: Kukjin Kim --- arch/arm/boot/dts/exynos3250-monk.dts | 8 ++++---- arch/arm/boot/dts/exynos3250-rinato.dts | 10 +++++----- 2 files changed, 9 insertions(+), 9 deletions(-) diff --git a/arch/arm/boot/dts/exynos3250-monk.dts b/arch/arm/boot/dts/exynos3250-monk.dts index 540a0adf2be6..c14129e0761d 100644 --- a/arch/arm/boot/dts/exynos3250-monk.dts +++ b/arch/arm/boot/dts/exynos3250-monk.dts @@ -52,13 +52,13 @@ regulator-name = "V_EMMC_2.8V-fixed"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; - gpio = <&gpk0 2 0>; + gpio = <&gpk0 2 GPIO_ACTIVE_HIGH>; enable-active-high; }; i2c_max77836: i2c-gpio-0 { compatible = "i2c-gpio"; - gpios = <&gpd0 2 0>, <&gpd0 3 0>; + gpios = <&gpd0 2 GPIO_ACTIVE_HIGH>, <&gpd0 3 GPIO_ACTIVE_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -266,14 +266,14 @@ regulator-name = "V_EMMC_1.8V"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; - samsung,ext-control-gpios = <&gpk0 2 0>; + samsung,ext-control-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>; }; ldo12_reg: LDO12 { regulator-name = "V_EMMC_2.8V"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; - samsung,ext-control-gpios = <&gpk0 2 0>; + samsung,ext-control-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>; }; ldo13_reg: LDO13 { diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts index 41a5fafb9aa9..830e216f7e10 100644 --- a/arch/arm/boot/dts/exynos3250-rinato.dts +++ b/arch/arm/boot/dts/exynos3250-rinato.dts @@ -49,7 +49,7 @@ i2c_max77836: i2c-gpio-0 { compatible = "i2c-gpio"; - gpios = <&gpd0 2 0>, <&gpd0 3 0>; + gpios = <&gpd0 2 GPIO_ACTIVE_HIGH>, <&gpd0 3 GPIO_ACTIVE_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -188,8 +188,8 @@ reg = <0>; vdd3-supply = <&ldo16_reg>; vci-supply = <&ldo20_reg>; - reset-gpios = <&gpe0 1 0>; - te-gpios = <&gpx0 6 0>; + reset-gpios = <&gpe0 1 GPIO_ACTIVE_HIGH>; + te-gpios = <&gpx0 6 GPIO_ACTIVE_HIGH>; power-on-delay= <30>; power-off-delay= <120>; reset-delay = <5>; @@ -368,14 +368,14 @@ regulator-name = "V_EMMC_1.8V"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; - samsung,ext-control-gpios = <&gpk0 2 0>; + samsung,ext-control-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>; }; ldo12_reg: LDO12 { regulator-name = "V_EMMC_2.8V"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; - samsung,ext-control-gpios = <&gpk0 2 0>; + samsung,ext-control-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>; }; ldo13_reg: LDO13 { From 39c1c413c1970803137d58ba25ea554f4f0fccea Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Thu, 8 Oct 2015 07:39:58 +0900 Subject: [PATCH 19/22] ARM: dts: Use GPIO constants for flags cells in exynos4120 boards The board DTS are using numeric values instead of the defined GPIO constanst to express polarity, use them to make the DTS more clear. Signed-off-by: Javier Martinez Canillas Signed-off-by: Kukjin Kim --- arch/arm/boot/dts/exynos4210-origen.dts | 15 +++---- arch/arm/boot/dts/exynos4210-smdkv310.dts | 3 +- arch/arm/boot/dts/exynos4210-trats.dts | 29 ++++++------- .../boot/dts/exynos4210-universal_c210.dts | 42 ++++++++++--------- 4 files changed, 47 insertions(+), 42 deletions(-) diff --git a/arch/arm/boot/dts/exynos4210-origen.dts b/arch/arm/boot/dts/exynos4210-origen.dts index e050d85cdacd..b8f866991bdd 100644 --- a/arch/arm/boot/dts/exynos4210-origen.dts +++ b/arch/arm/boot/dts/exynos4210-origen.dts @@ -16,6 +16,7 @@ /dts-v1/; #include "exynos4210.dtsi" +#include #include / { @@ -45,7 +46,7 @@ regulator-name = "VMEM_VDD_2.8V"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; - gpio = <&gpx1 1 0>; + gpio = <&gpx1 1 GPIO_ACTIVE_HIGH>; enable-active-high; }; }; @@ -57,35 +58,35 @@ up { label = "Up"; - gpios = <&gpx2 0 1>; + gpios = <&gpx2 0 GPIO_ACTIVE_LOW>; linux,code = ; gpio-key,wakeup; }; down { label = "Down"; - gpios = <&gpx2 1 1>; + gpios = <&gpx2 1 GPIO_ACTIVE_LOW>; linux,code = ; gpio-key,wakeup; }; back { label = "Back"; - gpios = <&gpx1 7 1>; + gpios = <&gpx1 7 GPIO_ACTIVE_LOW>; linux,code = ; gpio-key,wakeup; }; home { label = "Home"; - gpios = <&gpx1 6 1>; + gpios = <&gpx1 6 GPIO_ACTIVE_LOW>; linux,code = ; gpio-key,wakeup; }; menu { label = "Menu"; - gpios = <&gpx1 5 1>; + gpios = <&gpx1 5 GPIO_ACTIVE_LOW>; linux,code = ; gpio-key,wakeup; }; @@ -94,7 +95,7 @@ leds { compatible = "gpio-leds"; status { - gpios = <&gpx1 3 1>; + gpios = <&gpx1 3 GPIO_ACTIVE_LOW>; linux,default-trigger = "heartbeat"; }; }; diff --git a/arch/arm/boot/dts/exynos4210-smdkv310.dts b/arch/arm/boot/dts/exynos4210-smdkv310.dts index 043b03caff8f..bc1448ba95d3 100644 --- a/arch/arm/boot/dts/exynos4210-smdkv310.dts +++ b/arch/arm/boot/dts/exynos4210-smdkv310.dts @@ -16,6 +16,7 @@ /dts-v1/; #include "exynos4210.dtsi" +#include / { model = "Samsung smdkv310 evaluation board based on Exynos4210"; @@ -182,7 +183,7 @@ }; &spi_2 { - cs-gpios = <&gpc1 2 0>; + cs-gpios = <&gpc1 2 GPIO_ACTIVE_HIGH>; status = "okay"; w25x80@0 { diff --git a/arch/arm/boot/dts/exynos4210-trats.dts b/arch/arm/boot/dts/exynos4210-trats.dts index ba34886f8b65..c69e468efd2e 100644 --- a/arch/arm/boot/dts/exynos4210-trats.dts +++ b/arch/arm/boot/dts/exynos4210-trats.dts @@ -14,6 +14,7 @@ /dts-v1/; #include "exynos4210.dtsi" +#include / { model = "Samsung Trats based on Exynos4210"; @@ -39,7 +40,7 @@ regulator-name = "VMEM_VDD_2.8V"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; - gpio = <&gpk0 2 0>; + gpio = <&gpk0 2 GPIO_ACTIVE_HIGH>; enable-active-high; }; @@ -48,7 +49,7 @@ regulator-name = "TSP_FIXED_VOLTAGES"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; - gpio = <&gpl0 3 0>; + gpio = <&gpl0 3 GPIO_ACTIVE_HIGH>; enable-active-high; }; @@ -57,7 +58,7 @@ regulator-name = "8M_AF_2.8V_EN"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; - gpio = <&gpk1 1 0>; + gpio = <&gpk1 1 GPIO_ACTIVE_HIGH>; enable-active-high; }; @@ -66,7 +67,7 @@ regulator-name = "CAM_IO_EN"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; - gpio = <&gpe2 1 0>; + gpio = <&gpe2 1 GPIO_ACTIVE_HIGH>; enable-active-high; }; @@ -75,7 +76,7 @@ regulator-name = "8M_1.2V_EN"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; - gpio = <&gpe2 5 0>; + gpio = <&gpe2 5 GPIO_ACTIVE_HIGH>; enable-active-high; }; @@ -84,7 +85,7 @@ regulator-name = "VT_CORE_1.5V"; regulator-min-microvolt = <1500000>; regulator-max-microvolt = <1500000>; - gpio = <&gpe2 2 0>; + gpio = <&gpe2 2 GPIO_ACTIVE_HIGH>; enable-active-high; }; }; @@ -93,21 +94,21 @@ compatible = "gpio-keys"; vol-down-key { - gpios = <&gpx2 1 1>; + gpios = <&gpx2 1 GPIO_ACTIVE_LOW>; linux,code = <114>; label = "volume down"; debounce-interval = <10>; }; vol-up-key { - gpios = <&gpx2 0 1>; + gpios = <&gpx2 0 GPIO_ACTIVE_LOW>; linux,code = <115>; label = "volume up"; debounce-interval = <10>; }; power-key { - gpios = <&gpx2 7 1>; + gpios = <&gpx2 7 GPIO_ACTIVE_LOW>; linux,code = <116>; label = "power"; debounce-interval = <10>; @@ -115,7 +116,7 @@ }; ok-key { - gpios = <&gpx3 5 1>; + gpios = <&gpx3 5 GPIO_ACTIVE_LOW>; linux,code = <352>; label = "ok"; debounce-interval = <10>; @@ -218,7 +219,7 @@ compatible = "samsung,s6e8aa0"; vdd3-supply = <&vcclcd_reg>; vci-supply = <&vlcd_reg>; - reset-gpios = <&gpy4 5 0>; + reset-gpios = <&gpy4 5 GPIO_ACTIVE_HIGH>; power-on-delay= <50>; reset-delay = <100>; init-delay = <100>; @@ -304,9 +305,9 @@ max8997,pmic-ignore-gpiodvs-side-effect; max8997,pmic-buck125-default-dvs-idx = <0>; - max8997,pmic-buck125-dvs-gpios = <&gpx0 5 0>, - <&gpx0 6 0>, - <&gpl0 0 0>; + max8997,pmic-buck125-dvs-gpios = <&gpx0 5 GPIO_ACTIVE_HIGH>, + <&gpx0 6 GPIO_ACTIVE_HIGH>, + <&gpl0 0 GPIO_ACTIVE_HIGH>; max8997,pmic-buck1-dvs-voltage = <1350000>, <1300000>, <1250000>, <1200000>, diff --git a/arch/arm/boot/dts/exynos4210-universal_c210.dts b/arch/arm/boot/dts/exynos4210-universal_c210.dts index eb379526e234..896be8f2342d 100644 --- a/arch/arm/boot/dts/exynos4210-universal_c210.dts +++ b/arch/arm/boot/dts/exynos4210-universal_c210.dts @@ -14,6 +14,7 @@ /dts-v1/; #include "exynos4210.dtsi" +#include / { model = "Samsung Universal C210 based on Exynos4210 rev0"; @@ -65,7 +66,7 @@ regulator-name = "VMEM_VDD_2_8V"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; - gpio = <&gpe1 3 0>; + gpio = <&gpe1 3 GPIO_ACTIVE_HIGH>; enable-active-high; }; @@ -73,21 +74,21 @@ compatible = "gpio-keys"; vol-up-key { - gpios = <&gpx2 0 1>; + gpios = <&gpx2 0 GPIO_ACTIVE_LOW>; linux,code = <115>; label = "volume up"; debounce-interval = <1>; }; vol-down-key { - gpios = <&gpx2 1 1>; + gpios = <&gpx2 1 GPIO_ACTIVE_LOW>; linux,code = <114>; label = "volume down"; debounce-interval = <1>; }; config-key { - gpios = <&gpx2 2 1>; + gpios = <&gpx2 2 GPIO_ACTIVE_LOW>; linux,code = <171>; label = "config"; debounce-interval = <1>; @@ -95,14 +96,14 @@ }; camera-key { - gpios = <&gpx2 3 1>; + gpios = <&gpx2 3 GPIO_ACTIVE_LOW>; linux,code = <212>; label = "camera"; debounce-interval = <1>; }; power-key { - gpios = <&gpx2 7 1>; + gpios = <&gpx2 7 GPIO_ACTIVE_LOW>; linux,code = <116>; label = "power"; debounce-interval = <1>; @@ -110,7 +111,7 @@ }; ok-key { - gpios = <&gpx3 5 1>; + gpios = <&gpx3 5 GPIO_ACTIVE_LOW>; linux,code = <352>; label = "ok"; debounce-interval = <1>; @@ -122,7 +123,7 @@ regulator-name = "TSP_2_8V"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; - gpio = <&gpe2 3 0>; + gpio = <&gpe2 3 GPIO_ACTIVE_HIGH>; enable-active-high; }; @@ -131,17 +132,17 @@ #address-cells = <1>; #size-cells = <0>; - gpio-sck = <&gpy3 1 0>; - gpio-mosi = <&gpy3 3 0>; + gpio-sck = <&gpy3 1 GPIO_ACTIVE_HIGH>; + gpio-mosi = <&gpy3 3 GPIO_ACTIVE_HIGH>; num-chipselects = <1>; - cs-gpios = <&gpy4 3 0>; + cs-gpios = <&gpy4 3 GPIO_ACTIVE_HIGH>; lcd@0 { compatible = "samsung,ld9040"; reg = <0>; vdd3-supply = <&ldo7_reg>; vci-supply = <&ldo17_reg>; - reset-gpios = <&gpy4 5 0>; + reset-gpios = <&gpy4 5 GPIO_ACTIVE_HIGH>; spi-max-frequency = <1200000>; spi-cpol; spi-cpha; @@ -218,13 +219,13 @@ regulator-name = "HDMI_5V"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; - gpio = <&gpe0 1 0>; + gpio = <&gpe0 1 GPIO_ACTIVE_HIGH>; enable-active-high; }; hdmi_ddc: i2c-ddc { compatible = "i2c-gpio"; - gpios = <&gpe4 2 0 &gpe4 3 0>; + gpios = <&gpe4 2 GPIO_ACTIVE_HIGH &gpe4 3 GPIO_ACTIVE_HIGH>; i2c-gpio,delay-us = <100>; #address-cells = <1>; #size-cells = <0>; @@ -267,7 +268,7 @@ }; &hdmi { - hpd-gpio = <&gpx3 7 0>; + hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&hdmi_hpd>; hdmi-en-supply = <&hdmi_en>; @@ -311,7 +312,8 @@ compatible = "maxim,max8952"; reg = <0x60>; - max8952,vid-gpios = <&gpx0 3 0>, <&gpx0 4 0>; + max8952,vid-gpios = <&gpx0 3 GPIO_ACTIVE_HIGH>, + <&gpx0 4 GPIO_ACTIVE_HIGH>; max8952,default-mode = <0>; max8952,dvs-mode-microvolt = <1250000>, <1200000>, <1050000>, <950000>; @@ -330,13 +332,13 @@ reg = <0x66>; max8998,pmic-buck1-default-dvs-idx = <0>; - max8998,pmic-buck1-dvs-gpios = <&gpx0 5 0>, - <&gpx0 6 0>; + max8998,pmic-buck1-dvs-gpios = <&gpx0 5 GPIO_ACTIVE_HIGH>, + <&gpx0 6 GPIO_ACTIVE_HIGH>; max8998,pmic-buck1-dvs-voltage = <1100000>, <1000000>, <1100000>, <1000000>; max8998,pmic-buck2-default-dvs-idx = <0>; - max8998,pmic-buck2-dvs-gpio = <&gpe2 0 0>; + max8998,pmic-buck2-dvs-gpio = <&gpe2 0 GPIO_ACTIVE_HIGH>; max8998,pmic-buck2-dvs-voltage = <1200000>, <1100000>; regulators { @@ -551,7 +553,7 @@ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4>; pinctrl-names = "default"; vmmc-supply = <&ldo5_reg>; - cd-gpios = <&gpx3 4 0>; + cd-gpios = <&gpx3 4 GPIO_ACTIVE_HIGH>; cd-inverted; status = "okay"; }; From c10d3290cbde0e81d92d622e0b58eea2739fe557 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Thu, 8 Oct 2015 07:39:58 +0900 Subject: [PATCH 20/22] ARM: dts: Use GPIO constants for flags cells in exynos4412 boards The board DTS are using numeric values instead of the defined GPIO constanst to express polarity, use them to make the DTS more clear. Signed-off-by: Javier Martinez Canillas Signed-off-by: Kukjin Kim --- .../boot/dts/exynos4412-odroid-common.dtsi | 15 ++++---- arch/arm/boot/dts/exynos4412-odroidu3.dts | 2 +- arch/arm/boot/dts/exynos4412-odroidx.dts | 8 ++--- arch/arm/boot/dts/exynos4412-origen.dts | 15 ++++---- arch/arm/boot/dts/exynos4412-tiny4412.dts | 9 ++--- arch/arm/boot/dts/exynos4412-trats2.dts | 34 +++++++++---------- 6 files changed, 43 insertions(+), 40 deletions(-) diff --git a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi index c3e978d77367..edf0fc8db6ff 100644 --- a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi +++ b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi @@ -11,6 +11,7 @@ #include #include #include "exynos4412.dtsi" +#include / { chosen { @@ -30,7 +31,7 @@ power_key { interrupt-parent = <&gpx1>; interrupts = <3 0>; - gpios = <&gpx1 3 1>; + gpios = <&gpx1 3 GPIO_ACTIVE_LOW>; linux,code = ; label = "power key"; debounce-interval = <10>; @@ -70,7 +71,7 @@ pinctrl-0 = <&sd1_cd>; pinctrl-names = "default"; compatible = "mmc-pwrseq-emmc"; - reset-gpios = <&gpk1 2 1>; + reset-gpios = <&gpk1 2 GPIO_ACTIVE_LOW>; }; camera { @@ -181,7 +182,7 @@ }; &hdmi { - hpd-gpio = <&gpx3 7 0>; + hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&hdmi_hpd>; vdd-supply = <&ldo8_reg>; @@ -207,9 +208,9 @@ compatible = "smsc,usb3503"; reg = <0x08>; - intn-gpios = <&gpx3 0 0>; - connect-gpios = <&gpx3 4 0>; - reset-gpios = <&gpx3 5 0>; + intn-gpios = <&gpx3 0 GPIO_ACTIVE_HIGH>; + connect-gpios = <&gpx3 4 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpx3 5 GPIO_ACTIVE_HIGH>; initial-mode = <1>; }; @@ -482,7 +483,7 @@ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; pinctrl-names = "default"; vmmc-supply = <&ldo4_reg &ldo21_reg>; - cd-gpios = <&gpk2 2 0>; + cd-gpios = <&gpk2 2 GPIO_ACTIVE_HIGH>; cd-inverted; status = "okay"; }; diff --git a/arch/arm/boot/dts/exynos4412-odroidu3.dts b/arch/arm/boot/dts/exynos4412-odroidu3.dts index 1e6ef99eef59..646ff0bd001a 100644 --- a/arch/arm/boot/dts/exynos4412-odroidu3.dts +++ b/arch/arm/boot/dts/exynos4412-odroidu3.dts @@ -27,7 +27,7 @@ compatible = "gpio-leds"; led1 { label = "led1:heart"; - gpios = <&gpc1 0 1>; + gpios = <&gpc1 0 GPIO_ACTIVE_LOW>; default-state = "on"; linux,default-trigger = "heartbeat"; }; diff --git a/arch/arm/boot/dts/exynos4412-odroidx.dts b/arch/arm/boot/dts/exynos4412-odroidx.dts index 679ac103ebf6..b44bb682e976 100644 --- a/arch/arm/boot/dts/exynos4412-odroidx.dts +++ b/arch/arm/boot/dts/exynos4412-odroidx.dts @@ -26,13 +26,13 @@ compatible = "gpio-leds"; led1 { label = "led1:heart"; - gpios = <&gpc1 0 1>; + gpios = <&gpc1 0 GPIO_ACTIVE_LOW>; default-state = "on"; linux,default-trigger = "heartbeat"; }; led2 { label = "led2:mmc0"; - gpios = <&gpc1 2 1>; + gpios = <&gpc1 2 GPIO_ACTIVE_LOW>; default-state = "on"; linux,default-trigger = "mmc0"; }; @@ -44,7 +44,7 @@ home_key { interrupt-parent = <&gpx2>; interrupts = <2 0>; - gpios = <&gpx2 2 0>; + gpios = <&gpx2 2 GPIO_ACTIVE_HIGH>; linux,code = ; label = "home key"; debounce-interval = <10>; @@ -57,7 +57,7 @@ regulator-name = "p3v3_en"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; - gpio = <&gpa1 1 1>; + gpio = <&gpa1 1 GPIO_ACTIVE_LOW>; enable-active-high; regulator-always-on; }; diff --git a/arch/arm/boot/dts/exynos4412-origen.dts b/arch/arm/boot/dts/exynos4412-origen.dts index 9d528af68c1a..c8d86af2fb98 100644 --- a/arch/arm/boot/dts/exynos4412-origen.dts +++ b/arch/arm/boot/dts/exynos4412-origen.dts @@ -14,6 +14,7 @@ /dts-v1/; #include "exynos4412.dtsi" +#include #include / { @@ -45,7 +46,7 @@ regulator-name = "VMEM_VDD_2.8V"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; - gpio = <&gpx1 1 0>; + gpio = <&gpx1 1 GPIO_ACTIVE_HIGH>; enable-active-high; }; }; @@ -107,13 +108,13 @@ s5m8767,pmic-buck-default-dvs-idx = <3>; - s5m8767,pmic-buck-dvs-gpios = <&gpx2 3 0>, - <&gpx2 4 0>, - <&gpx2 5 0>; + s5m8767,pmic-buck-dvs-gpios = <&gpx2 3 GPIO_ACTIVE_HIGH>, + <&gpx2 4 GPIO_ACTIVE_HIGH>, + <&gpx2 5 GPIO_ACTIVE_HIGH>; - s5m8767,pmic-buck-ds-gpios = <&gpm3 5 0>, - <&gpm3 6 0>, - <&gpm3 7 0>; + s5m8767,pmic-buck-ds-gpios = <&gpm3 5 GPIO_ACTIVE_HIGH>, + <&gpm3 6 GPIO_ACTIVE_HIGH>, + <&gpm3 7 GPIO_ACTIVE_HIGH>; s5m8767,pmic-buck2-dvs-voltage = <1250000>, <1200000>, <1200000>, <1200000>, diff --git a/arch/arm/boot/dts/exynos4412-tiny4412.dts b/arch/arm/boot/dts/exynos4412-tiny4412.dts index 525684ca8dc0..4840bbdaa9ec 100644 --- a/arch/arm/boot/dts/exynos4412-tiny4412.dts +++ b/arch/arm/boot/dts/exynos4412-tiny4412.dts @@ -13,6 +13,7 @@ /dts-v1/; #include "exynos4412.dtsi" +#include / { model = "FriendlyARM TINY4412 board based on Exynos4412"; @@ -31,26 +32,26 @@ led1 { label = "led1"; - gpios = <&gpm4 0 1>; + gpios = <&gpm4 0 GPIO_ACTIVE_LOW>; default-state = "off"; linux,default-trigger = "heartbeat"; }; led2 { label = "led2"; - gpios = <&gpm4 1 1>; + gpios = <&gpm4 1 GPIO_ACTIVE_LOW>; default-state = "off"; }; led3 { label = "led3"; - gpios = <&gpm4 2 1>; + gpios = <&gpm4 2 GPIO_ACTIVE_LOW>; default-state = "off"; }; led4 { label = "led4"; - gpios = <&gpm4 3 1>; + gpios = <&gpm4 3 GPIO_ACTIVE_LOW>; default-state = "off"; linux,default-trigger = "mmc0"; }; diff --git a/arch/arm/boot/dts/exynos4412-trats2.dts b/arch/arm/boot/dts/exynos4412-trats2.dts index 93e3bbd4bd49..d8bf4afb8bd9 100644 --- a/arch/arm/boot/dts/exynos4412-trats2.dts +++ b/arch/arm/boot/dts/exynos4412-trats2.dts @@ -65,7 +65,7 @@ regulator-name = "CAM_SENSOR_A"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; - gpio = <&gpm0 2 0>; + gpio = <&gpm0 2 GPIO_ACTIVE_HIGH>; enable-active-high; }; @@ -74,7 +74,7 @@ regulator-name = "LCD_VDD_2.2V"; regulator-min-microvolt = <2200000>; regulator-max-microvolt = <2200000>; - gpio = <&gpc0 1 0>; + gpio = <&gpc0 1 GPIO_ACTIVE_HIGH>; enable-active-high; }; @@ -83,7 +83,7 @@ regulator-name = "CAM_AF"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; - gpio = <&gpm0 4 0>; + gpio = <&gpm0 4 GPIO_ACTIVE_HIGH>; enable-active-high; }; @@ -92,7 +92,7 @@ regulator-name = "LED_A_3.0V"; regulator-min-microvolt = <3000000>; regulator-max-microvolt = <3000000>; - gpio = <&gpj0 5 0>; + gpio = <&gpj0 5 GPIO_ACTIVE_HIGH>; enable-active-high; }; }; @@ -101,21 +101,21 @@ compatible = "gpio-keys"; key-down { - gpios = <&gpx3 3 1>; + gpios = <&gpx3 3 GPIO_ACTIVE_LOW>; linux,code = <114>; label = "volume down"; debounce-interval = <10>; }; key-up { - gpios = <&gpx2 2 1>; + gpios = <&gpx2 2 GPIO_ACTIVE_LOW>; linux,code = <115>; label = "volume up"; debounce-interval = <10>; }; key-power { - gpios = <&gpx2 7 1>; + gpios = <&gpx2 7 GPIO_ACTIVE_LOW>; linux,code = <116>; label = "power"; debounce-interval = <10>; @@ -123,7 +123,7 @@ }; key-ok { - gpios = <&gpx0 1 1>; + gpios = <&gpx0 1 GPIO_ACTIVE_LOW>; linux,code = <139>; label = "ok"; debounce-inteval = <10>; @@ -198,7 +198,7 @@ i2c_ak8975: i2c-gpio-0 { compatible = "i2c-gpio"; - gpios = <&gpy2 4 0>, <&gpy2 5 0>; + gpios = <&gpy2 4 GPIO_ACTIVE_HIGH>, <&gpy2 5 GPIO_ACTIVE_HIGH>; i2c-gpio,delay-us = <2>; #address-cells = <1>; #size-cells = <0>; @@ -207,13 +207,13 @@ ak8975@0c { compatible = "asahi-kasei,ak8975"; reg = <0x0c>; - gpios = <&gpj0 7 0>; + gpios = <&gpj0 7 GPIO_ACTIVE_HIGH>; }; }; i2c_cm36651: i2c-gpio-2 { compatible = "i2c-gpio"; - gpios = <&gpf0 0 1>, <&gpf0 1 1>; + gpios = <&gpf0 0 GPIO_ACTIVE_LOW>, <&gpf0 1 GPIO_ACTIVE_LOW>; i2c-gpio,delay-us = <2>; #address-cells = <1>; #size-cells = <0>; @@ -359,7 +359,7 @@ reg = <0>; vdd3-supply = <&lcd_vdd3_reg>; vci-supply = <&ldo25_reg>; - reset-gpios = <&gpy4 5 0>; + reset-gpios = <&gpy4 5 GPIO_ACTIVE_HIGH>; power-on-delay= <50>; reset-delay = <100>; init-delay = <100>; @@ -446,7 +446,7 @@ clocks = <&camera 1>; clock-names = "extclk"; samsung,camclk-out = <1>; - gpios = <&gpm1 6 0>; + gpios = <&gpm1 6 GPIO_ACTIVE_HIGH>; port { is_s5k6a3_ep: endpoint { @@ -488,8 +488,8 @@ s5c73m3@3c { compatible = "samsung,s5c73m3"; reg = <0x3c>; - standby-gpios = <&gpm0 1 1>; /* ISP_STANDBY */ - xshutdown-gpios = <&gpf1 3 1>; /* ISP_RESET */ + standby-gpios = <&gpm0 1 GPIO_ACTIVE_LOW>; /* ISP_STANDBY */ + xshutdown-gpios = <&gpf1 3 GPIO_ACTIVE_LOW>; /* ISP_RESET */ vdd-int-supply = <&buck9_reg>; vddio-cis-supply = <&ldo9_reg>; vdda-supply = <&ldo17_reg>; @@ -1241,7 +1241,7 @@ &sdhci_2 { bus-width = <4>; - cd-gpios = <&gpx3 4 0>; + cd-gpios = <&gpx3 4 GPIO_ACTIVE_HIGH>; cd-inverted; pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4>; pinctrl-names = "default"; @@ -1268,7 +1268,7 @@ &spi_1 { pinctrl-names = "default"; pinctrl-0 = <&spi1_bus>; - cs-gpios = <&gpb 5 0>; + cs-gpios = <&gpb 5 GPIO_ACTIVE_HIGH>; status = "okay"; s5c73m3_spi: s5c73m3 { From 31b9903c233e831f3b0c05c6a62c0e39e85e77ec Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Thu, 8 Oct 2015 07:39:58 +0900 Subject: [PATCH 21/22] ARM: dts: Use GPIO constants for flags cells in exynos5420/5422/5800 boards The board DTS are using numeric values instead of the defined GPIO constanst to express polarity, use them to make the DTS more clear. Signed-off-by: Javier Martinez Canillas Signed-off-by: Kukjin Kim --- arch/arm/boot/dts/exynos5420-arndale-octa.dts | 3 ++- arch/arm/boot/dts/exynos5420-peach-pit.dts | 8 ++++---- arch/arm/boot/dts/exynos5420-smdk5420.dts | 7 ++++--- arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 4 ++-- arch/arm/boot/dts/exynos5800-peach-pi.dts | 8 ++++---- 5 files changed, 16 insertions(+), 14 deletions(-) diff --git a/arch/arm/boot/dts/exynos5420-arndale-octa.dts b/arch/arm/boot/dts/exynos5420-arndale-octa.dts index eeb4ac22cfce..4ecef6981d5c 100644 --- a/arch/arm/boot/dts/exynos5420-arndale-octa.dts +++ b/arch/arm/boot/dts/exynos5420-arndale-octa.dts @@ -11,6 +11,7 @@ /dts-v1/; #include "exynos5420.dtsi" +#include #include #include #include @@ -44,7 +45,7 @@ wakeup { label = "SW-TACT1"; - gpios = <&gpx2 7 1>; + gpios = <&gpx2 7 GPIO_ACTIVE_LOW>; linux,code = ; gpio-key,wakeup; }; diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/exynos5420-peach-pit.dts index ac02fb42ac0c..e722c22b2ba9 100644 --- a/arch/arm/boot/dts/exynos5420-peach-pit.dts +++ b/arch/arm/boot/dts/exynos5420-peach-pit.dts @@ -94,7 +94,7 @@ regulator-name = "P5.0V_USB3CON0"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; - gpio = <&gph0 0 0>; + gpio = <&gph0 0 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&usb300_vbus_en>; enable-active-high; @@ -105,7 +105,7 @@ regulator-name = "P5.0V_USB3CON1"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; - gpio = <&gph0 1 0>; + gpio = <&gph0 1 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&usb301_vbus_en>; enable-active-high; @@ -153,7 +153,7 @@ samsung,color-depth = <1>; samsung,link-rate = <0x06>; samsung,lane-count = <2>; - samsung,hpd-gpio = <&gpx2 6 0>; + samsung,hpd-gpio = <&gpx2 6 GPIO_ACTIVE_HIGH>; ports { port@0 { @@ -925,7 +925,7 @@ status = "okay"; num-cs = <1>; samsung,spi-src-clk = <0>; - cs-gpios = <&gpb1 2 0>; + cs-gpios = <&gpb1 2 GPIO_ACTIVE_HIGH>; cros_ec: cros-ec@0 { compatible = "google,cros-ec-spi"; diff --git a/arch/arm/boot/dts/exynos5420-smdk5420.dts b/arch/arm/boot/dts/exynos5420-smdk5420.dts index 7520d52f4e22..ac35aefd320f 100644 --- a/arch/arm/boot/dts/exynos5420-smdk5420.dts +++ b/arch/arm/boot/dts/exynos5420-smdk5420.dts @@ -11,6 +11,7 @@ /dts-v1/; #include "exynos5420.dtsi" +#include / { model = "Samsung SMDK5420 board based on EXYNOS5420"; @@ -69,7 +70,7 @@ regulator-name = "VBUS0"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; - gpio = <&gpg0 5 0>; + gpio = <&gpg0 5 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&usb300_vbus_en>; enable-active-high; @@ -80,7 +81,7 @@ regulator-name = "VBUS1"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; - gpio = <&gpg1 4 0>; + gpio = <&gpg1 4 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&usb301_vbus_en>; enable-active-high; @@ -121,7 +122,7 @@ &hdmi { status = "okay"; - hpd-gpio = <&gpx3 7 0>; + hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&hdmi_hpd_irq>; }; diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi index a83d569baea8..1af5bdc2bdb1 100644 --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi @@ -43,7 +43,7 @@ pinctrl-0 = <&emmc_nrst_pin>; pinctrl-names = "default"; compatible = "mmc-pwrseq-emmc"; - reset-gpios = <&gpd1 0 1>; + reset-gpios = <&gpd1 0 GPIO_ACTIVE_LOW>; }; fan0: pwm-fan { @@ -74,7 +74,7 @@ &hdmi { status = "okay"; - hpd-gpio = <&gpx3 7 0>; + hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&hdmi_hpd_irq>; diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts index b60dec0f1f67..56275a6f9fca 100644 --- a/arch/arm/boot/dts/exynos5800-peach-pi.dts +++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts @@ -94,7 +94,7 @@ regulator-name = "P5.0V_USB3CON0"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; - gpio = <&gph0 0 0>; + gpio = <&gph0 0 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&usb300_vbus_en>; enable-active-high; @@ -105,7 +105,7 @@ regulator-name = "P5.0V_USB3CON1"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; - gpio = <&gph0 1 0>; + gpio = <&gph0 1 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&usb301_vbus_en>; enable-active-high; @@ -147,7 +147,7 @@ samsung,color-depth = <1>; samsung,link-rate = <0x0a>; samsung,lane-count = <2>; - samsung,hpd-gpio = <&gpx2 6 0>; + samsung,hpd-gpio = <&gpx2 6 GPIO_ACTIVE_HIGH>; panel = <&panel>; }; @@ -888,7 +888,7 @@ status = "okay"; num-cs = <1>; samsung,spi-src-clk = <0>; - cs-gpios = <&gpb1 2 0>; + cs-gpios = <&gpb1 2 GPIO_ACTIVE_HIGH>; cros_ec: cros-ec@0 { compatible = "google,cros-ec-spi"; From df829b06f0079165d9dc7719af8f8a7da852fe51 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Thu, 8 Oct 2015 07:39:58 +0900 Subject: [PATCH 22/22] ARM: dts: Use GPIO constants for flags cells in exynos5440 boards The board DTS are using numeric values instead of the defined GPIO constanst to express polarity, use them to make the DTS more clear. Signed-off-by: Javier Martinez Canillas Signed-off-by: Kukjin Kim --- arch/arm/boot/dts/exynos5440-ssdk5440.dts | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/exynos5440-ssdk5440.dts b/arch/arm/boot/dts/exynos5440-ssdk5440.dts index e4443f4e6572..6a0d802e87c8 100644 --- a/arch/arm/boot/dts/exynos5440-ssdk5440.dts +++ b/arch/arm/boot/dts/exynos5440-ssdk5440.dts @@ -11,6 +11,7 @@ /dts-v1/; #include "exynos5440.dtsi" +#include / { model = "SAMSUNG SSDK5440 board based on EXYNOS5440"; @@ -29,12 +30,12 @@ }; &pcie_0 { - reset-gpio = <&pin_ctrl 5 0>; + reset-gpio = <&pin_ctrl 5 GPIO_ACTIVE_HIGH>; status = "okay"; }; &pcie_1 { - reset-gpio = <&pin_ctrl 22 0>; + reset-gpio = <&pin_ctrl 22 GPIO_ACTIVE_HIGH>; status = "okay"; };