From f0dc35a514c3ef8a65826a965b647dc09c2e0cd3 Mon Sep 17 00:00:00 2001 From: Ryan Hsu Date: Tue, 13 Dec 2016 14:55:19 -0800 Subject: [PATCH 1/2] ath10k: fix incorrect txpower set by P2P_DEVICE interface Ath10k reports the phy capability that supports P2P_DEVICE interface. When we use the P2P supported wpa_supplicant to start connection, it'll create two interfaces, one is wlan0 (vdev_id=0) and one is P2P_DEVICE p2p-dev-wlan0 which is for p2p control channel (vdev_id=1). ath10k_pci mac vdev create 0 (add interface) type 2 subtype 0 ath10k_add_interface: vdev_id: 0, txpower: 0, bss_power: 0 ... ath10k_pci mac vdev create 1 (add interface) type 2 subtype 1 ath10k_add_interface: vdev_id: 1, txpower: 0, bss_power: 0 And the txpower in per vif bss_conf will only be set to valid tx power when the interface is assigned with channel_ctx. But this P2P_DEVICE interface will never be used for any connection, so that the uninitialized bss_conf.txpower=0 is assinged to the arvif->txpower when interface created. Since the txpower configuration is firmware per physical interface. So the smallest txpower of all vifs will be the one limit the tx power of the physical device, that causing the low txpower issue on other active interfaces. wlan0: Limiting TX power to 21 (24 - 3) dBm ath10k_pci mac vdev_id 0 txpower 21 ath10k_mac_txpower_recalc: vdev_id: 1, txpower: 0 ath10k_mac_txpower_recalc: vdev_id: 0, txpower: 21 ath10k_pci mac txpower 0 This issue only happens when we use the wpa_supplicant that supports P2P or if we use the iw tool to create the control P2P_DEVICE interface. Signed-off-by: Ryan Hsu Signed-off-by: Kalle Valo Git-repo: git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next.git Git-commit: 88407beb1b1462f706a1950a355fd086e1c450b6 CRs-Fixed: 2027293 Change-Id: Ib56352e1601e7400b856cfafe67503bee98d5ced Signed-off-by: Rajeev Kumar Sirasanagandla --- drivers/net/wireless/ath/ath10k/mac.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c index 35e5d980ed49..ac8f8811e972 100644 --- a/drivers/net/wireless/ath/ath10k/mac.c +++ b/drivers/net/wireless/ath/ath10k/mac.c @@ -4671,7 +4671,8 @@ static int ath10k_mac_txpower_recalc(struct ath10k *ar) lockdep_assert_held(&ar->conf_mutex); list_for_each_entry(arvif, &ar->arvifs, list) { - WARN_ON(arvif->txpower < 0); + if (arvif->txpower <= 0) + continue; if (txpower == -1) txpower = arvif->txpower; @@ -4679,8 +4680,8 @@ static int ath10k_mac_txpower_recalc(struct ath10k *ar) txpower = min(txpower, arvif->txpower); } - if (WARN_ON(txpower == -1)) - return -EINVAL; + if (txpower == -1) + return 0; ret = ath10k_mac_txpower_setup(ar, txpower); if (ret) { From adad11994aa56a53e06ad468c3c36734a00c4cd8 Mon Sep 17 00:00:00 2001 From: Ryan Hsu Date: Thu, 22 Dec 2016 14:31:46 -0800 Subject: [PATCH 2/2] ath10k: recal the txpower when removing interface The txpower is being recalculated when adding interface to make sure txpower won't overshoot the spec, and when removing the interface, the txpower should again to be recalculated to restore the correct value from the active interface list. Following is one of the scenario vdev0 is created as STA and connected: txpower:23 vdev1 is created as P2P_DEVICE for control interface: txpower:0 vdev2 is created as p2p go/gc interface: txpower is 21 So the vdev2@txpower:21 will be set to firmware when vdev2 is created. When we tear down the vdev2, the txpower needs to be recalculated to re-set it to vdev0@txpower:23 as vdev0/vdev1 are the active interface. ath10k_pci mac vdev 0 peer create 8c:fd:f0:01:62:98 ath10k_pci mac vdev_id 0 txpower 23 ... (adding interface) ath10k_pci mac vdev create 2 (add interface) type 1 subtype 3 ath10k_pci mac vdev_id 2 txpower 21 ath10k_pci mac txpower 21 ... (removing interface) ath10k_pci mac vdev 2 delete (remove interface) ath10k_pci vdev 1 txpower 0 ath10k_pci vdev 0 txpower 23 ath10k_pci mac txpower 23 Signed-off-by: Ryan Hsu Signed-off-by: Kalle Valo Git-repo: git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next.git Git-commit: d679fa1b3c8997e3a371da3cca08c44a38054c34 CRs-Fixed: 2027293 Change-Id: I56befd4c4fd80ab77ed65926663a1f2471701f68 Signed-off-by: Rajeev Kumar Sirasanagandla --- drivers/net/wireless/ath/ath10k/mac.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c index ac8f8811e972..d1775748a7cd 100644 --- a/drivers/net/wireless/ath/ath10k/mac.c +++ b/drivers/net/wireless/ath/ath10k/mac.c @@ -5191,6 +5191,10 @@ static void ath10k_remove_interface(struct ieee80211_hw *hw, ath10k_warn(ar, "failed to recalc monitor: %d\n", ret); } + ret = ath10k_mac_txpower_recalc(ar); + if (ret) + ath10k_warn(ar, "failed to recalc tx power: %d\n", ret); + spin_lock_bh(&ar->htt.tx_lock); ath10k_mac_vif_tx_unlock_all(arvif); spin_unlock_bh(&ar->htt.tx_lock);