diff --git a/arch/arm/boot/dts/qcom/sdm630-camera-sensor-mtp.dtsi b/arch/arm/boot/dts/qcom/sdm630-camera-sensor-mtp.dtsi
index 94158834eee6..0275016c9662 100644
--- a/arch/arm/boot/dts/qcom/sdm630-camera-sensor-mtp.dtsi
+++ b/arch/arm/boot/dts/qcom/sdm630-camera-sensor-mtp.dtsi
@@ -29,6 +29,36 @@
 		qcom,switch-source = <&pm660l_switch1>;
 		status = "ok";
 	};
+
+	cam_avdd_gpio_regulator: cam_avdd_fixed_regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "cam_avdd_gpio_regulator";
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+		enable-active-high;
+		gpio = <&tlmm 51 0>;
+		vin-supply = <&pm660l_bob>;
+	};
+
+	cam_dvdd_gpio_regulator: cam_dvdd_fixed_regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "cam_dvdd_gpio_regulator";
+		regulator-min-microvolt = <1350000>;
+		regulator-max-microvolt = <1350000>;
+		enable-active-high;
+		gpio = <&pm660l_gpios 3 0>;
+		vin-supply = <&pm660_s5>;
+	};
+
+	cam_rear_dvdd_gpio_regulator: cam_rear_dvdd_fixed_regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "cam_rear_dvdd_gpio_regulator";
+		regulator-min-microvolt = <1350000>;
+		regulator-max-microvolt = <1350000>;
+		enable-active-high;
+		gpio = <&pm660l_gpios 4 0>;
+		vin-supply = <&pm660_s5>;
+	};
 };
 
 &cci {
@@ -89,14 +119,14 @@
 		reg = <0>;
 		compatible = "qcom,eeprom";
 		cam_vio-supply = <&pm660_l11>;
-		cam_vana-supply = <&pm660l_bob>;
-		cam_vdig-supply = <&pm660_s5>;
+		cam_vana-supply = <&cam_avdd_gpio_regulator>;
+		cam_vdig-supply = <&cam_rear_dvdd_gpio_regulator>;
 		cam_vaf-supply = <&pm660l_l8>;
 		qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig",
 					"cam_vaf";
-		qcom,cam-vreg-min-voltage = <1780000 3300000 1350000 2800000>;
-		qcom,cam-vreg-max-voltage = <1950000 3600000 1350000 3400000>;
-		qcom,cam-vreg-op-mode = <105000 80000 105000 100000>;
+		qcom,cam-vreg-min-voltage = <1780000 0 0 2800000>;
+		qcom,cam-vreg-max-voltage = <1950000 0 0 3400000>;
+		qcom,cam-vreg-op-mode = <105000 0 0 100000>;
 		qcom,gpio-no-mux = <0>;
 		pinctrl-names = "cam_default", "cam_suspend";
 		pinctrl-0 = <&cam_sensor_mclk0_active
@@ -104,18 +134,12 @@
 		pinctrl-1 = <&cam_sensor_mclk0_suspend
 				&cam_sensor_rear_suspend>;
 		gpios = <&tlmm 32 0>,
-			<&tlmm 46 0>,
-			<&pm660l_gpios 4 0>,
-			<&tlmm 51 0>;
+			<&tlmm 46 0>;
 		qcom,gpio-reset = <1>;
-		qcom,gpio-vdig = <2>;
-		qcom,gpio-vana = <3>;
-		qcom,gpio-req-tbl-num = <0 1 2 3>;
-		qcom,gpio-req-tbl-flags = <1 0 0 0>;
+		qcom,gpio-req-tbl-num = <0 1>;
+		qcom,gpio-req-tbl-flags = <1 0>;
 		qcom,gpio-req-tbl-label = "CAMIF_MCLK0",
-					"CAM_RESET0",
-					"CAM_VDIG",
-					"CAM_VANA";
+					"CAM_RESET0";
 		qcom,sensor-position = <0>;
 		qcom,sensor-mode = <0>;
 		qcom,cci-master = <0>;
@@ -131,14 +155,14 @@
 		reg = <0x1>;
 		compatible = "qcom,eeprom";
 		cam_vio-supply = <&pm660_l11>;
-		cam_vana-supply = <&pm660l_bob>;
-		cam_vdig-supply = <&pm660_s5>;
+		cam_vana-supply = <&cam_avdd_gpio_regulator>;
+		cam_vdig-supply = <&cam_dvdd_gpio_regulator>;
 		cam_vaf-supply = <&pm660l_l8>;
 		qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig",
 					"cam_vaf";
-		qcom,cam-vreg-min-voltage = <1780000 3300000 1350000 2800000>;
-		qcom,cam-vreg-max-voltage = <1950000 3600000 1350000 3400000>;
-		qcom,cam-vreg-op-mode = <105000 80000 105000 100000>;
+		qcom,cam-vreg-min-voltage = <1780000 0 0 2800000>;
+		qcom,cam-vreg-max-voltage = <1950000 0 0 3400000>;
+		qcom,cam-vreg-op-mode = <105000 0 0 100000>;
 		qcom,gpio-no-mux = <0>;
 		pinctrl-names = "cam_default", "cam_suspend";
 		pinctrl-0 = <&cam_sensor_mclk2_active
@@ -146,18 +170,12 @@
 		pinctrl-1 = <&cam_sensor_mclk2_suspend
 			&cam_sensor_rear2_suspend>;
 		gpios = <&tlmm 34 0>,
-		    <&tlmm 48 0>,
-		    <&pm660l_gpios 3 0>,
-		    <&tlmm 51 0>;
+		    <&tlmm 48 0>;
 		qcom,gpio-reset = <1>;
-		qcom,gpio-vdig = <2>;
-		qcom,gpio-vana = <3>;
-		qcom,gpio-req-tbl-num = <0 1 2 3>;
-		qcom,gpio-req-tbl-flags = <1 0 0 0>;
+		qcom,gpio-req-tbl-num = <0 1>;
+		qcom,gpio-req-tbl-flags = <1 0>;
 		qcom,gpio-req-tbl-label = "CAMIF_MCLK",
-				"CAM_RESET",
-				"CAM_VDIG",
-				"CAM_VANA";
+				"CAM_RESET";
 		qcom,sensor-position = <0>;
 		qcom,sensor-mode = <0>;
 		qcom,cci-master = <1>;
@@ -174,12 +192,12 @@
 		compatible = "qcom,eeprom";
 		cam_vio-supply = <&pm660_l11>;
 		cam_vana-supply = <&pm660l_bob>;
-		cam_vdig-supply = <&pm660_s5>;
+		cam_vdig-supply = <&cam_dvdd_gpio_regulator>;
 		qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig",
 					"cam_vaf";
-		qcom,cam-vreg-min-voltage = <1780000 3300000 1350000 2800000>;
-		qcom,cam-vreg-max-voltage = <1950000 3600000 1350000 3400000>;
-		qcom,cam-vreg-op-mode = <105000 80000 105000 100000>;
+		qcom,cam-vreg-min-voltage = <1780000 3300000 0 2800000>;
+		qcom,cam-vreg-max-voltage = <1950000 3600000 0 3400000>;
+		qcom,cam-vreg-op-mode = <105000 80000 0 100000>;
 		qcom,gpio-no-mux = <0>;
 		pinctrl-names = "cam_default", "cam_suspend";
 		pinctrl-0 = <&cam_sensor_mclk1_active
@@ -188,16 +206,13 @@
 				 &cam_sensor_front_suspend>;
 		gpios = <&tlmm 33 0>,
 			<&tlmm 47 0>,
-			<&pm660_gpios 3 0>,
 			<&tlmm 44 0>;
 		qcom,gpio-reset = <1>;
-		qcom,gpio-vdig = <2>;
-		qcom,gpio-vana = <3>;
-		qcom,gpio-req-tbl-num = <0 1 2 3>;
-		qcom,gpio-req-tbl-flags = <1 0 0 0>;
+		qcom,gpio-vana = <2>;
+		qcom,gpio-req-tbl-num = <0 1 2>;
+		qcom,gpio-req-tbl-flags = <1 0 0>;
 		qcom,gpio-req-tbl-label = "CAMIF_MCLK2",
 					"CAM_RESET2",
-					"CAM_VDIG",
 					"CAM_VANA";
 		qcom,sensor-position = <1>;
 		qcom,sensor-mode = <0>;
@@ -221,12 +236,12 @@
 		qcom,ois-src = <&ois0>;
 		qcom,eeprom-src = <&eeprom0>;
 		cam_vio-supply = <&pm660_l11>;
-		cam_vana-supply = <&pm660l_bob>;
-		cam_vdig-supply = <&pm660_s5>;
+		cam_vana-supply = <&cam_avdd_gpio_regulator>;
+		cam_vdig-supply = <&cam_rear_dvdd_gpio_regulator>;
 		qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig";
-		qcom,cam-vreg-min-voltage = <1780000 3300000 1350000>;
-		qcom,cam-vreg-max-voltage = <1950000 3600000 1350000>;
-		qcom,cam-vreg-op-mode = <105000 80000 105000>;
+		qcom,cam-vreg-min-voltage = <1780000 0 0>;
+		qcom,cam-vreg-max-voltage = <1950000 0 0>;
+		qcom,cam-vreg-op-mode = <105000 0 0>;
 		qcom,gpio-no-mux = <0>;
 		pinctrl-names = "cam_default", "cam_suspend";
 		pinctrl-0 = <&cam_sensor_mclk0_active
@@ -234,18 +249,12 @@
 		pinctrl-1 = <&cam_sensor_mclk0_suspend
 				 &cam_sensor_rear_suspend>;
 		gpios = <&tlmm 32 0>,
-			<&tlmm 46 0>,
-			<&pm660l_gpios 4 0>,
-			<&tlmm 51 0>;
+			<&tlmm 46 0>;
 		qcom,gpio-reset = <1>;
-		qcom,gpio-vdig = <2>;
-		qcom,gpio-vana = <3>;
-		qcom,gpio-req-tbl-num = <0 1 2 3>;
-		qcom,gpio-req-tbl-flags = <1 0 0 0>;
+		qcom,gpio-req-tbl-num = <0 1>;
+		qcom,gpio-req-tbl-flags = <1 0>;
 		qcom,gpio-req-tbl-label = "CAMIF_MCLK0",
-					"CAM_RESET0",
-					"CAM_VDIG",
-					"CAM_VANA";
+					"CAM_RESET0";
 		qcom,sensor-position = <0>;
 		qcom,sensor-mode = <0>;
 		qcom,cci-master = <0>;
@@ -266,12 +275,12 @@
 		qcom,actuator-src = <&actuator1>;
 		qcom,eeprom-src = <&eeprom1>;
 		cam_vio-supply = <&pm660_l11>;
-		cam_vana-supply = <&pm660l_bob>;
-		cam_vdig-supply = <&pm660_s5>;
+		cam_vana-supply = <&cam_avdd_gpio_regulator>;
+		cam_vdig-supply = <&cam_dvdd_gpio_regulator>;
 		qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig";
-		qcom,cam-vreg-min-voltage = <1780000 3300000 1350000>;
-		qcom,cam-vreg-max-voltage = <1950000 3600000 1350000>;
-		qcom,cam-vreg-op-mode = <105000 80000 105000>;
+		qcom,cam-vreg-min-voltage = <1780000 0 0>;
+		qcom,cam-vreg-max-voltage = <1950000 0 0>;
+		qcom,cam-vreg-op-mode = <105000 0 0>;
 		qcom,gpio-no-mux = <0>;
 		pinctrl-names = "cam_default", "cam_suspend";
 		pinctrl-0 = <&cam_sensor_mclk2_active
@@ -279,18 +288,12 @@
 		pinctrl-1 = <&cam_sensor_mclk2_suspend
 				 &cam_sensor_rear2_suspend>;
 		gpios = <&tlmm 34 0>,
-			<&tlmm 48 0>,
-			<&pm660l_gpios 3 0>,
-			<&tlmm 51 0>;
+			<&tlmm 48 0>;
 		qcom,gpio-reset = <1>;
-		qcom,gpio-vdig = <2>;
-		qcom,gpio-vana = <3>;
-		qcom,gpio-req-tbl-num = <0 1 2 3>;
-		qcom,gpio-req-tbl-flags = <1 0 0 0>;
+		qcom,gpio-req-tbl-num = <0 1>;
+		qcom,gpio-req-tbl-flags = <1 0>;
 		qcom,gpio-req-tbl-label = "CAMIF_MCLK",
-					  "CAM_RESET",
-					  "CAM_VDIG",
-					  "CAM_VANA";
+					  "CAM_RESET";
 		qcom,sensor-position = <0>;
 		qcom,sensor-mode = <0>;
 		qcom,cci-master = <1>;
@@ -311,12 +314,12 @@
 		qcom,actuator-src = <&actuator2>;
 		qcom,eeprom-src = <&eeprom2>;
 		cam_vio-supply = <&pm660_l11>;
-		cam_vana-supply = <&pm660l_bob>;
-		cam_vdig-supply = <&pm660_s5>;
+		cam_vana-supply = <&cam_avdd_gpio_regulator>;
+		cam_vdig-supply = <&cam_dvdd_gpio_regulator>;
 		qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig";
-		qcom,cam-vreg-min-voltage = <1780000 3300000 1350000>;
-		qcom,cam-vreg-max-voltage = <1950000 3600000 1350000>;
-		qcom,cam-vreg-op-mode = <105000 80000 105000>;
+		qcom,cam-vreg-min-voltage = <1780000 0 0>;
+		qcom,cam-vreg-max-voltage = <1950000 0 0>;
+		qcom,cam-vreg-op-mode = <105000 0 0>;
 		qcom,gpio-no-mux = <0>;
 		pinctrl-names = "cam_default", "cam_suspend";
 		pinctrl-0 = <&cam_sensor_mclk1_active
@@ -324,18 +327,12 @@
 		pinctrl-1 = <&cam_sensor_mclk1_suspend
 				 &cam_sensor_front_suspend>;
 		gpios = <&tlmm 33 0>,
-			<&tlmm 47 0>,
-			<&pm660l_gpios 3 0>,
-			<&tlmm 51 0>;
+			<&tlmm 47 0>;
 		qcom,gpio-reset = <1>;
-		qcom,gpio-vdig = <2>;
-		qcom,gpio-vana = <3>;
-		qcom,gpio-req-tbl-num = <0 1 2 3>;
-		qcom,gpio-req-tbl-flags = <1 0 0 0>;
+		qcom,gpio-req-tbl-num = <0 1>;
+		qcom,gpio-req-tbl-flags = <1 0>;
 		qcom,gpio-req-tbl-label = "CAMIF_MCLK2",
-					"CAM_RESET2",
-					"CAM_VDIG",
-					"CAM_VANA";
+					"CAM_RESET2";
 		qcom,sensor-position = <1>;
 		qcom,sensor-mode = <0>;
 		qcom,cci-master = <1>;
@@ -345,6 +342,46 @@
 		clock-names = "cam_src_clk", "cam_clk";
 		qcom,clock-rates = <24000000 0>;
 	};
+
+	qcom,camera@3 {
+		cell-index = <3>;
+		compatible = "qcom,camera";
+		reg = <0x03>;
+		qcom,csiphy-sd-index = <1>;
+		qcom,csid-sd-index = <1>;
+		qcom,mount-angle = <90>;
+		qcom,led-flash-src = <&led_flash1>;
+		qcom,actuator-src = <&actuator2>;
+		qcom,eeprom-src = <&eeprom2>;
+		cam_vio-supply = <&pm660_l11>;
+		cam_vana-supply = <&cam_avdd_gpio_regulator>;
+		cam_vdig-supply = <&cam_dvdd_gpio_regulator>;
+		qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig";
+		qcom,cam-vreg-min-voltage = <1780000 0 0>;
+		qcom,cam-vreg-max-voltage = <1950000 0 0>;
+		qcom,cam-vreg-op-mode = <105000 0 0>;
+		qcom,gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_front_iris_active>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_front_iris_suspend>;
+		gpios = <&tlmm 35 0>,
+			<&tlmm 52 0>;
+		qcom,gpio-reset = <1>;
+		qcom,gpio-req-tbl-num = <0 1>;
+		qcom,gpio-req-tbl-flags = <1 0>;
+		qcom,gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		qcom,sensor-position = <1>;
+		qcom,sensor-mode = <0>;
+		qcom,cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_mmss MCLK3_CLK_SRC>,
+			<&clock_mmss MMSS_CAMSS_MCLK3_CLK>;
+		clock-names = "cam_src_clk", "cam_clk";
+		qcom,clock-rates = <24000000 0>;
+	};
 };
 
 &pm660l_gpios {