ARM: dts: msm: Add camera node for msmcobalt QVR board
Add rear, front and fish eye node for msmcobalt QVR board camera. Add eeprom, actuator, flash node for msmcobalt QVR board camera. Change-Id: Ie263acbb0dd9cab06b239e14526be13622bd282d Signed-off-by: Wei Ding <weiding@codeaurora.org>
This commit is contained in:
Wei Ding
Gerrit - the friendly Code Review server
parent
85d7e134cc
commit
f87c68c909
2 changed files with 370 additions and 0 deletions
arch/arm/boot/dts/qcom
369
arch/arm/boot/dts/qcom/msmcobalt-camera-sensor-qrd-vr1.dtsi
Normal file
369
arch/arm/boot/dts/qcom/msmcobalt-camera-sensor-qrd-vr1.dtsi
Normal file
|
|
@ -0,0 +1,369 @@
|
|||
/*
|
||||
* Copyright (c) 2016, The Linux Foundation. All rights reserved.
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 and
|
||||
* only version 2 as published by the Free Software Foundation.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*/
|
||||
|
||||
&soc {
|
||||
led_flash0: qcom,camera-flash@0 {
|
||||
cell-index = <0>;
|
||||
compatible = "qcom,camera-flash";
|
||||
qcom,flash-source = <&pmicobalt_flash0 &pmicobalt_flash1>;
|
||||
qcom,switch-source = <&pmicobalt_switch0>;
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
led_flash1: qcom,camera-flash@1 {
|
||||
cell-index = <1>;
|
||||
compatible = "qcom,camera-flash";
|
||||
qcom,flash-source = <&pmicobalt_flash2>;
|
||||
qcom,switch-source = <&pmicobalt_switch1>;
|
||||
status = "ok";
|
||||
};
|
||||
};
|
||||
|
||||
&tlmm{
|
||||
cam_sensor_front_active: cam_sensor_front_active {
|
||||
/* RESET */
|
||||
mux {
|
||||
pins = "gpio9";
|
||||
function = "gpio";
|
||||
};
|
||||
|
||||
config {
|
||||
pins = "gpio9";
|
||||
bias-disable; /* No PULL */
|
||||
drive-strength = <2>; /* 2 MA */
|
||||
};
|
||||
};
|
||||
|
||||
cam_sensor_front_suspend: cam_sensor_front_suspend {
|
||||
/* RESET */
|
||||
mux {
|
||||
pins = "gpio9";
|
||||
function = "gpio";
|
||||
};
|
||||
|
||||
config {
|
||||
pins = "gpio9";
|
||||
bias-disable; /* No PULL */
|
||||
drive-strength = <2>; /* 2 MA */
|
||||
};
|
||||
};
|
||||
|
||||
cam_sensor_rear2_active: cam_sensor_rear2_active {
|
||||
/* RESET, STANDBY */
|
||||
mux {
|
||||
pins = "gpio27","gpio8";
|
||||
function = "gpio";
|
||||
};
|
||||
|
||||
config {
|
||||
pins = "gpio27","gpio8";
|
||||
bias-disable; /* No PULL */
|
||||
drive-strength = <2>; /* 2 MA */
|
||||
};
|
||||
};
|
||||
|
||||
cam_sensor_rear2_suspend: cam_sensor_rear2_suspend {
|
||||
/* RESET, STANDBY */
|
||||
mux {
|
||||
pins = "gpio27","gpio8";
|
||||
function = "gpio";
|
||||
};
|
||||
config {
|
||||
pins = "gpio27","gpio8";
|
||||
bias-disable; /* No PULL */
|
||||
drive-strength = <2>; /* 2 MA */
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
&cci {
|
||||
actuator0: qcom,actuator@0 {
|
||||
cell-index = <0>;
|
||||
reg = <0x0>;
|
||||
compatible = "qcom,actuator";
|
||||
qcom,cci-master = <0>;
|
||||
};
|
||||
|
||||
actuator1: qcom,actuator@1 {
|
||||
cell-index = <1>;
|
||||
reg = <0x1>;
|
||||
compatible = "qcom,actuator";
|
||||
qcom,cci-master = <0>;
|
||||
};
|
||||
|
||||
eeprom0: qcom,eeprom@0 {
|
||||
cell-index = <0>;
|
||||
reg = <0>;
|
||||
compatible = "qcom,eeprom";
|
||||
cam_vio-supply = <&pmcobalt_lvs1>;
|
||||
cam_vana-supply = <&pmicobalt_bob>;
|
||||
cam_vdig-supply = <&pmcobalt_s3>;
|
||||
qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig";
|
||||
qcom,cam-vreg-min-voltage = <0 3312000 1352000>;
|
||||
qcom,cam-vreg-max-voltage = <0 3600000 1352000>;
|
||||
qcom,cam-vreg-op-mode = <0 80000 105000>;
|
||||
qcom,gpio-no-mux = <0>;
|
||||
pinctrl-names = "cam_default", "cam_suspend";
|
||||
pinctrl-0 = <&cam_sensor_mclk0_active
|
||||
&cam_sensor_rear_active>;
|
||||
pinctrl-1 = <&cam_sensor_mclk0_suspend
|
||||
&cam_sensor_rear_suspend>;
|
||||
gpios = <&tlmm 13 0>,
|
||||
<&tlmm 30 0>,
|
||||
<&pmcobalt_gpios 20 0>,
|
||||
<&tlmm 29 0>;
|
||||
qcom,gpio-reset = <1>;
|
||||
qcom,gpio-vdig = <2>;
|
||||
qcom,gpio-vana = <3>;
|
||||
qcom,gpio-req-tbl-num = <0 1 2 3>;
|
||||
qcom,gpio-req-tbl-flags = <1 0 0 0>;
|
||||
qcom,gpio-req-tbl-label = "CAMIF_MCLK0",
|
||||
"CAM_RESET0",
|
||||
"CAM_VDIG",
|
||||
"CAM_VANA";
|
||||
qcom,sensor-position = <0>;
|
||||
qcom,sensor-mode = <0>;
|
||||
qcom,cci-master = <0>;
|
||||
status = "ok";
|
||||
clocks = <&clock_mmss clk_mclk0_clk_src>,
|
||||
<&clock_mmss clk_mmss_camss_mclk0_clk>;
|
||||
clock-names = "cam_src_clk", "cam_clk";
|
||||
qcom,clock-rates = <24000000 0>;
|
||||
};
|
||||
|
||||
eeprom1: qcom,eeprom@1 {
|
||||
cell-index = <1>;
|
||||
reg = <0x1>;
|
||||
compatible = "qcom,eeprom";
|
||||
cam_vdig-supply = <&pmcobalt_lvs1>;
|
||||
cam_vio-supply = <&pmcobalt_lvs1>;
|
||||
cam_vana-supply = <&pmicobalt_bob>;
|
||||
qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana";
|
||||
qcom,cam-vreg-min-voltage = <0 0 3312000>;
|
||||
qcom,cam-vreg-max-voltage = <0 0 3600000>;
|
||||
qcom,cam-vreg-op-mode = <0 0 80000>;
|
||||
qcom,gpio-no-mux = <0>;
|
||||
pinctrl-names = "cam_default", "cam_suspend";
|
||||
pinctrl-0 = <&cam_sensor_mclk1_active
|
||||
&cam_sensor_rear2_active>;
|
||||
pinctrl-1 = <&cam_sensor_mclk1_suspend
|
||||
&cam_sensor_rear2_suspend>;
|
||||
gpios = <&tlmm 14 0>,
|
||||
<&tlmm 27 0>,
|
||||
<&tlmm 8 0>;
|
||||
qcom,gpio-standby = <1>;
|
||||
qcom,gpio-vana = <2>;
|
||||
qcom,gpio-req-tbl-num = <0 1 2>;
|
||||
qcom,gpio-req-tbl-flags = <1 0 0>;
|
||||
qcom,gpio-req-tbl-label = "CAMIF_MCLK1",
|
||||
"CAM_STANDBY1",
|
||||
"CAM_VANA";
|
||||
qcom,sensor-position = <0>;
|
||||
qcom,sensor-mode = <0>;
|
||||
qcom,cci-master = <1>;
|
||||
status = "ok";
|
||||
clocks = <&clock_mmss clk_mclk1_clk_src>,
|
||||
<&clock_mmss clk_mmss_camss_mclk1_clk>;
|
||||
clock-names = "cam_src_clk", "cam_clk";
|
||||
qcom,clock-rates = <24000000 0>;
|
||||
};
|
||||
|
||||
eeprom2: qcom,eeprom@2 {
|
||||
cell-index = <2>;
|
||||
reg = <0x2>;
|
||||
compatible = "qcom,eeprom";
|
||||
cam_vio-supply = <&pmcobalt_lvs1>;
|
||||
cam_vana-supply = <&pmcobalt_l22>;
|
||||
cam_vdig-supply = <&pmcobalt_s3>;
|
||||
qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig";
|
||||
qcom,cam-vreg-min-voltage = <0 2864000 1352000>;
|
||||
qcom,cam-vreg-max-voltage = <0 2864000 1352000>;
|
||||
qcom,cam-vreg-op-mode = <0 80000 105000>;
|
||||
qcom,gpio-no-mux = <0>;
|
||||
pinctrl-names = "cam_default", "cam_suspend";
|
||||
pinctrl-0 = <&cam_sensor_mclk2_active
|
||||
&cam_sensor_front_active>;
|
||||
pinctrl-1 = <&cam_sensor_mclk2_active
|
||||
&cam_sensor_front_suspend>;
|
||||
gpios = <&tlmm 15 0>,
|
||||
<&tlmm 9 0>,
|
||||
<&pmcobalt_gpios 9 0>;
|
||||
qcom,gpio-reset = <1>;
|
||||
qcom,gpio-vdig = <2>;
|
||||
qcom,gpio-req-tbl-num = <0 1 2>;
|
||||
qcom,gpio-req-tbl-flags = <1 0 0>;
|
||||
qcom,gpio-req-tbl-label = "CAMIF_MCLK2",
|
||||
"CAM_RESET2",
|
||||
"CAM_VDIG";
|
||||
qcom,sensor-position = <1>;
|
||||
qcom,sensor-mode = <0>;
|
||||
qcom,cci-master = <1>;
|
||||
status = "ok";
|
||||
clocks = <&clock_mmss clk_mclk2_clk_src>,
|
||||
<&clock_mmss clk_mmss_camss_mclk2_clk>;
|
||||
clock-names = "cam_src_clk", "cam_clk";
|
||||
qcom,clock-rates = <24000000 0>;
|
||||
};
|
||||
|
||||
qcom,camera@0 {
|
||||
cell-index = <0>;
|
||||
compatible = "qcom,camera";
|
||||
reg = <0x0>;
|
||||
qcom,csiphy-sd-index = <0>;
|
||||
qcom,csid-sd-index = <0>;
|
||||
qcom,mount-angle = <270>;
|
||||
qcom,led-flash-src = <&led_flash0>;
|
||||
qcom,actuator-src = <&actuator0>;
|
||||
qcom,eeprom-src = <&eeprom0>;
|
||||
cam_vio-supply = <&pmcobalt_lvs1>;
|
||||
cam_vana-supply = <&pmicobalt_bob>;
|
||||
cam_vdig-supply = <&pmcobalt_s3>;
|
||||
qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig";
|
||||
qcom,cam-vreg-min-voltage = <0 3312000 1352000>;
|
||||
qcom,cam-vreg-max-voltage = <0 3600000 1352000>;
|
||||
qcom,cam-vreg-op-mode = <0 80000 105000>;
|
||||
qcom,gpio-no-mux = <0>;
|
||||
pinctrl-names = "cam_default", "cam_suspend";
|
||||
pinctrl-0 = <&cam_sensor_mclk0_active
|
||||
&cam_sensor_rear_active>;
|
||||
pinctrl-1 = <&cam_sensor_mclk0_suspend
|
||||
&cam_sensor_rear_suspend>;
|
||||
gpios = <&tlmm 13 0>,
|
||||
<&tlmm 30 0>,
|
||||
<&pmcobalt_gpios 20 0>,
|
||||
<&tlmm 29 0>;
|
||||
qcom,gpio-reset = <1>;
|
||||
qcom,gpio-vdig = <2>;
|
||||
qcom,gpio-vana = <3>;
|
||||
qcom,gpio-req-tbl-num = <0 1 2 3>;
|
||||
qcom,gpio-req-tbl-flags = <1 0 0 0>;
|
||||
qcom,gpio-req-tbl-label = "CAMIF_MCLK0",
|
||||
"CAM_RESET0",
|
||||
"CAM_VDIG",
|
||||
"CAM_VANA";
|
||||
qcom,sensor-position = <0>;
|
||||
qcom,sensor-mode = <0>;
|
||||
qcom,cci-master = <0>;
|
||||
status = "ok";
|
||||
clocks = <&clock_mmss clk_mclk0_clk_src>,
|
||||
<&clock_mmss clk_mmss_camss_mclk0_clk>;
|
||||
clock-names = "cam_src_clk", "cam_clk";
|
||||
qcom,clock-rates = <24000000 0>;
|
||||
};
|
||||
|
||||
qcom,camera@1 {
|
||||
cell-index = <1>;
|
||||
compatible = "qcom,camera";
|
||||
reg = <0x1>;
|
||||
qcom,csiphy-sd-index = <1>;
|
||||
qcom,csid-sd-index = <1>;
|
||||
qcom,mount-angle = <90>;
|
||||
qcom,eeprom-src = <&eeprom1>;
|
||||
cam_vio-supply = <&pmcobalt_lvs1>;
|
||||
cam_vana-supply = <&pmicobalt_bob>;
|
||||
qcom,cam-vreg-name = "cam_vio", "cam_vana";
|
||||
qcom,cam-vreg-min-voltage = <0 3312000>;
|
||||
qcom,cam-vreg-max-voltage = <0 3600000>;
|
||||
qcom,cam-vreg-op-mode = <0 80000>;
|
||||
qcom,gpio-no-mux = <0>;
|
||||
pinctrl-names = "cam_default", "cam_suspend";
|
||||
pinctrl-0 = <&cam_sensor_mclk1_active
|
||||
&cam_sensor_rear2_active>;
|
||||
pinctrl-1 = <&cam_sensor_mclk1_suspend
|
||||
&cam_sensor_rear2_suspend>;
|
||||
gpios = <&tlmm 14 0>,
|
||||
<&tlmm 27 0>,
|
||||
<&tlmm 8 0>;
|
||||
qcom,gpio-standby = <1>;
|
||||
qcom,gpio-vana = <2>;
|
||||
qcom,gpio-req-tbl-num = <0 1 2>;
|
||||
qcom,gpio-req-tbl-flags = <1 0 0>;
|
||||
qcom,gpio-req-tbl-label = "CAMIF_MCLK1",
|
||||
"CAM_STANDBY1",
|
||||
"CAM_VANA1";
|
||||
qcom,sensor-position = <0>;
|
||||
qcom,sensor-mode = <0>;
|
||||
qcom,cci-master = <1>;
|
||||
status = "ok";
|
||||
clocks = <&clock_mmss clk_mclk1_clk_src>,
|
||||
<&clock_mmss clk_mmss_camss_mclk1_clk>;
|
||||
clock-names = "cam_src_clk", "cam_clk";
|
||||
qcom,clock-rates = <24000000 0>;
|
||||
};
|
||||
|
||||
qcom,camera@2 {
|
||||
cell-index = <2>;
|
||||
compatible = "qcom,camera";
|
||||
reg = <0x02>;
|
||||
qcom,csiphy-sd-index = <2>;
|
||||
qcom,csid-sd-index = <2>;
|
||||
qcom,mount-angle = <90>;
|
||||
qcom,eeprom-src = <&eeprom2>;
|
||||
qcom,led-flash-src = <&led_flash1>;
|
||||
qcom,actuator-src = <&actuator1>;
|
||||
cam_vio-supply = <&pmcobalt_lvs1>;
|
||||
cam_vana-supply = <&pmcobalt_l22>;
|
||||
cam_vdig-supply = <&pmcobalt_s3>;
|
||||
qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig";
|
||||
qcom,cam-vreg-min-voltage = <0 2864000 1352000>;
|
||||
qcom,cam-vreg-max-voltage = <0 2864000 1352000>;
|
||||
qcom,cam-vreg-op-mode = <0 80000 105000>;
|
||||
qcom,gpio-no-mux = <0>;
|
||||
pinctrl-names = "cam_default", "cam_suspend";
|
||||
pinctrl-0 = <&cam_sensor_mclk2_active
|
||||
&cam_sensor_front_active>;
|
||||
pinctrl-1 = <&cam_sensor_mclk2_suspend
|
||||
&cam_sensor_front_suspend>;
|
||||
gpios = <&tlmm 15 0>,
|
||||
<&tlmm 9 0>,
|
||||
<&pmcobalt_gpios 9 0>;
|
||||
qcom,gpio-reset = <1>;
|
||||
qcom,gpio-vdig = <2>;
|
||||
qcom,gpio-req-tbl-num = <0 1 2>;
|
||||
qcom,gpio-req-tbl-flags = <1 0 0>;
|
||||
qcom,gpio-req-tbl-label = "CAMIF_MCLK2",
|
||||
"CAM_RESET2",
|
||||
"CAM_VDIG";
|
||||
qcom,sensor-position = <1>;
|
||||
qcom,sensor-mode = <0>;
|
||||
qcom,cci-master = <1>;
|
||||
status = "ok";
|
||||
clocks = <&clock_mmss clk_mclk2_clk_src>,
|
||||
<&clock_mmss clk_mmss_camss_mclk2_clk>;
|
||||
clock-names = "cam_src_clk", "cam_clk";
|
||||
qcom,clock-rates = <24000000 0>;
|
||||
};
|
||||
};
|
||||
|
||||
&pmcobalt_gpios {
|
||||
gpio@c800 { /* GPIO 9 - CAMERA SENSOR 2 VDIG */
|
||||
qcom,mode = <1>; /* Output */
|
||||
qcom,pull = <5>; /* No Pull */
|
||||
qcom,vin-sel = <0>; /* VIN1 GPIO_LV */
|
||||
qcom,src-sel = <0>; /* GPIO */
|
||||
qcom,invert = <0>; /* Invert */
|
||||
qcom,master-en = <1>; /* Enable GPIO */
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
gpio@d300 { /* GPIO 20 - CAMERA SENSOR 0 VDIG */
|
||||
qcom,mode = <1>; /* Output */
|
||||
qcom,pull = <5>; /* No Pull */
|
||||
qcom,vin-sel = <1>; /* VIN1 GPIO_MV */
|
||||
qcom,src-sel = <0>; /* GPIO */
|
||||
qcom,invert = <0>; /* Invert */
|
||||
qcom,master-en = <1>; /* Enable GPIO */
|
||||
status = "ok";
|
||||
};
|
||||
};
|
||||
|
|
@ -12,6 +12,7 @@
|
|||
|
||||
#include <dt-bindings/interrupt-controller/irq.h>
|
||||
#include "msmcobalt-pinctrl.dtsi"
|
||||
#include "msmcobalt-camera-sensor-qrd-vr1.dtsi"
|
||||
|
||||
&blsp1_uart3_hs {
|
||||
status = "ok";
|
||||
|
|
|
|||
Loading…
Add table
Reference in a new issue