commit 225ece3e7dad4cfc44cca38ce7a3a80f255ea8f1 upstream.
In case DECO0 cannot be acquired - i.e. run_descriptor_deco0() fails
with -ENODEV, caam_probe() enters an endless loop:
run_descriptor_deco0
ret -ENODEV
-> instantiate_rng
-ENODEV, overwritten by -EAGAIN
ret -EAGAIN
-> caam_probe
-EAGAIN results in endless loop
It turns out the error path in instantiate_rng() is incorrect,
the checks are done in the wrong order.
Fixes: 1005bccd7a ("crypto: caam - enable instantiation of all RNG4 state handles")
Reported-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Suggested-by: Auer Lukas <lukas.auer@aisec.fraunhofer.de>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7459e1d25ffefa2b1be799477fcc1f6c62f6cec7 upstream.
Driver does not properly handle the case when signals interrupt
wait_for_completion_interruptible():
-it does not check for return value
-completion structure is allocated on stack; in case a signal interrupts
the sleep, it will go out of scope, causing the worker thread
(caam_jr_dequeue) to fail when it accesses it
wait_for_completion_interruptible() is replaced with uninterruptable
wait_for_completion().
We choose to block all signals while waiting for I/O (device executing
the split key generation job descriptor) since the alternative - in
order to have a deterministic device state - would be to flush the job
ring (aborting *all* in-progress jobs).
Fixes: 045e36780f ("crypto: caam - ahash hmac support")
Fixes: 4c1ec1f930 ("crypto: caam - refactor key_gen, sg")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40c98cb57cdbc377456116ad4582c89e329721b0 upstream.
RNG instantiation was previously fixed by
commit 62743a4145 ("crypto: caam - fix RNG init descriptor ret. code checking")
while deinstantiation was not addressed.
Since the descriptors used are similar, in the sense that they both end
with a JUMP HALT command, checking for errors should be similar too,
i.e. status code 7000_0000h should be considered successful.
Fixes: 1005bccd7a ("crypto: caam - enable instantiation of all RNG4 state handles")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d128af17876d79b87edf048303f98b35f6a53dbc upstream.
The AEAD givenc descriptor relies on moving the IV through the
output FIFO and then back to the CTX2 for authentication. The
SEQ FIFO STORE could be scheduled before the data can be
read from OFIFO, especially since the SEQ FIFO LOAD needs
to wait for the SEQ FIFO LOAD SKIP to finish first. The
SKIP takes more time when the input is SG than when it's
a contiguous buffer. If the SEQ FIFO LOAD is not scheduled
before the STORE, the DECO will hang waiting for data
to be available in the OFIFO so it can be transferred to C2.
In order to overcome this, first force transfer of IV to C2
by starting the "cryptlen" transfer first and then starting to
store data from OFIFO to the output buffer.
Fixes: 1acebad3d8 ("crypto: caam - faster aead implementation")
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83d2c9a9c17b1e9f23a3a0c24c03cd18e4b02520 upstream.
When using AES-XTS on a Wandboard, we receive a Mode error:
caam_jr 2102000.jr1: 20001311: CCB: desc idx 19: AES: Mode error.
According to the Security Reference Manual, the Low Power AES units
of the i.MX6 do not support the XTS mode. Therefore we must not
register XTS implementations in the Crypto API.
Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: c6415a6016 "crypto: caam - add support for acipher xts(aes)"
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
commit 8b18e2359aff2ab810aba84cebffc9da07fef78f upstream.
For algorithms that implement IV generators before the crypto ops,
the IV needed for decryption is initially located in req->src
scatterlist, not in req->iv.
Avoid copying the IV into req->iv by modifying the (givdecrypt)
descriptors to load it directly from req->src.
aead_givdecrypt() is no longer needed and goes away.
Fixes: 479bcc7c5b ("crypto: caam - Convert authenc to new AEAD interface")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2fdea258fde036a87d3396ec9c0ef66f10768530 upstream.
To be able to generate shared descriptors for AEAD, the authentication size
needs to be known. However, there is no imposed order of calling .setkey,
.setauthsize callbacks.
Thus, in case authentication size is not known at .setkey time, defer it
until .setauthsize is called.
The authsize != 0 check was incorrectly removed when converting the driver
to the new AEAD interface.
Fixes: 479bcc7c5b ("crypto: caam - Convert authenc to new AEAD interface")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d2d87e81ea21f64c19b95ef228b865a6880e17e upstream.
There are a few things missed by the conversion to the
new AEAD interface:
1 - echainiv(authenc) encrypt shared descriptor
The shared descriptor is incorrect: due to the order of operations,
at some point in time MATH3 register is being overwritten.
2 - buffer used for echainiv(authenc) encrypt shared descriptor
Encrypt and givencrypt shared descriptors (for AEAD ops) are mutually
exclusive and thus use the same buffer in context state: sh_desc_enc.
However, there's one place missed by s/sh_desc_givenc/sh_desc_enc,
leading to errors when echainiv(authenc(...)) algorithms are used:
DECO: desc idx 14: Header Error. Invalid length or parity, or
certain other problems.
While here, also fix a typo: dma_mapping_error() is checking
for validity of sh_desc_givenc_dma instead of sh_desc_enc_dma.
Fixes: 479bcc7c5b ("crypto: caam - Convert authenc to new AEAD interface")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a0118c8b2be9297aed8e915c60b4013326b256d4 upstream.
Since 6de62f15b581 ("crypto: algif_hash - Require setkey before
accept(2)"), the AF_ALG interface requires userspace to provide a key
to any algorithm that has a setkey method. However, the non-HMAC
algorithms are not keyed, so setting a key is unnecessary.
Fix this by removing the setkey method from the non-keyed hash
algorithms.
Fixes: 6de62f15b581 ("crypto: algif_hash - Require setkey before accept(2)")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e930c765ca5c6b039cd22ebfb4504ea7b5dab43d upstream.
caam_jr_alloc() used to return NULL if a JR device could not be
allocated for a session. In turn, every user of this function used
IS_ERR() function to verify if anything went wrong, which does NOT look
for NULL values. This made the kernel crash if the sanity check failed,
because the driver continued to think it had allocated a valid JR dev
instance to the session and at some point it tries to do a caam_jr_free()
on a NULL JR dev pointer.
This patch is a fix for this issue.
Signed-off-by: Catalin Vasile <cata.vasile@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7a7104e432c0db8469ca3568daf4f1d1afe3e73 upstream.
Previous change (see "Fixes" tag) to the MCFGR register
clears AWCACHE[0] ("bufferable" AXI3 attribute) (which is "1" at POR).
This makes all writes non-bufferable, causing a ~ 5% performance drop
for PPC-based platforms.
Rework previous change such that MCFGR[AWCACHE]=4'b0011
(bufferable + cacheable) for all platforms.
Note: For ARM-based platforms, AWCACHE[0] is ignored
by the interconnect IP.
Fixes: f109674951 ("crypto: caam - fix snooping for write transactions")
Signed-off-by: Horia Geant? <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel's coding style suggests that closing braces for initialisers
should not be aligned to the open brace column. The CodingStyle doc
shows how this should be done. Remove the additional tab.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Avoid exporting lots of state by only exporting what we really require,
which is the buffer containing the set of pending bytes to be hashed,
number of pending bytes, the context buffer, and the function pointer
state. This reduces down the exported state size to 216 bytes from
576 bytes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
caam does not properly calculate the size of the retained state
when non-block aligned hashes are requested - it uses the wrong
buffer sizes, which results in errors such as:
caam_jr 2102000.jr1: 40000501: DECO: desc idx 5: SGT Length Error. The descriptor is trying to read more data than is contained in the SGT table.
We end up here with:
in_len 0x46 blocksize 0x40 last_bufsize 0x0 next_bufsize 0x6
to_hash 0x40 ctx_len 0x28 nbytes 0x20
which results in a job descriptor of:
jobdesc@889: ed03d918: b0861c08 3daa0080 f1400000 3d03d938
jobdesc@889: ed03d928: 00000068 f8400000 3cde2a40 00000028
where the word at 0xed03d928 is the expected data size (0x68), and a
scatterlist containing:
sg@892: ed03d938: 00000000 3cde2a40 00000028 00000000
sg@892: ed03d948: 00000000 3d03d100 00000006 00000000
sg@892: ed03d958: 00000000 7e8aa700 40000020 00000000
0x68 comes from 0x28 (the context size) plus the "in_len" rounded down
to a block size (0x40). in_len comes from 0x26 bytes of unhashed data
from the previous operation, plus the 0x20 bytes from the latest
operation.
The fixed version would create:
sg@892: ed03d938: 00000000 3cde2a40 00000028 00000000
sg@892: ed03d948: 00000000 3d03d100 00000026 00000000
sg@892: ed03d958: 00000000 7e8aa700 40000020 00000000
which replaces the 0x06 length with the correct 0x26 bytes of previously
unhashed data.
This fixes a previous commit which erroneously "fixed" this due to a
DMA-API bug report; that commit indicates that the bug was caused via a
test_ahash_pnum() function in the tcrypt module. No such function has
ever existed in the mainline kernel. Given that the change in this
commit has been tested with DMA API debug enabled and shows no issue,
I can only conclude that test_ahash_pnum() was triggering that bad
behaviour by CAAM.
Fixes: 7d5196aba3 ("crypto: caam - Correct DMA unmap size in ahash_update_ctx()")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When exporting and importing the hash state, we will only export and
import into hashes which share the same struct crypto_ahash pointer.
(See hash_accept->af_alg_accept->hash_accept_parent.)
This means that saving the caam_hash_ctx structure on export, and
restoring it on import is a waste of resources. So, remove this code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Print the errno code when hash registration fails, so we know why the
failure occurred. This aids debugging.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for AES working in XEX-based Tweaked-codebook mode with
ciphertext Stealing (XTS)
sector index - HW limitation: CAAM device supports sector index of only
8 bytes to be used for sector index inside IV, instead of whole 16 bytes
received on request. This represents 2 ^ 64 = 16,777,216 Tera of possible
values for sector index.
Signed-off-by: Cristian Hristea <cristi.hristea@gmail.com>
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Catalin Vasile <catalin.vasile@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The caam driver use two dma_map_sg path according to SG are chained
or not.
Since dma_map_sg can handle both case, clean the code with all
references to sg chained.
Thus removing dma_map_sg_chained, dma_unmap_sg_chained
and __sg_count functions.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit a1efb01fec ("jump_label, locking/static_keys: Rename
JUMP_LABEL_TYPE_* and related helpers to the static_key* pattern")
introduced the definition of JUMP_TYPE_MASK in
include/linux/jump_label.h causing the following name collision:
In file included from drivers/crypto/caam/desc_constr.h:7:0,
from drivers/crypto/caam/ctrl.c:15:
drivers/crypto/caam/desc.h:1495:0: warning: "JUMP_TYPE_MASK" redefined
#define JUMP_TYPE_MASK (0x03 << JUMP_TYPE_SHIFT)
^
In file included from include/linux/module.h:19:0,
from drivers/crypto/caam/compat.h:9,
from drivers/crypto/caam/ctrl.c:11:
include/linux/jump_label.h:131:0: note: this is the location of the previous definition
#define JUMP_TYPE_MASK 1UL
As JUMP_TYPE_MASK definition in desc.h is never used, we can safely remove
it to avoid the name collision.
Reported-by: Olof's autobuilder <build@lixom.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
"The preferred form for passing a size of a struct is the following:
p = kmalloc(sizeof(*p), ...);
....
The preferred form for allocating a zeroed array is the following:
p = kcalloc(n, sizeof(...), ...); "
,so do as suggested.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Instead of propagating a 'fake' error code, just propagate the real
one in the case of caam_drv_identify_clk() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In the error path we should disable the resources that were previously
acquired, so fix the error handling accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Most significant part of JQCR (Job Queue Control Register) contains
bits that control endianness: ILE - Immediate Little Endian,
DWS - Double Word Swap.
The bits are automatically set by the Job Queue Controller HW.
Unfortunately these bits are cleared in SW when submitting descriptors
via the register-based service interface.
>From LS1021A:
JQCR_MS = 08080100 - before writing: ILE | DWS | SRC (JR0)
JQCR_MS = 30000100 - after writing: WHL | FOUR | SRC (JR0)
This would cause problems on little endian caam for descriptors
containing immediata data or double-word pointers.
Currently there is no problem since the only descriptors ran through
this interface are the ones that (un)instantiate RNG.
Signed-off-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
LS1021A is a QorIQ SoC having little endian CAAM.
There are a few differences b/w QorIQ and i.MX from CAAM perspective:
1. i.MX platforms are somewhat special wrt. 64-bit registers:
-big endian format at 64-bit level: MSW at address+0 and LSW at address+4
-little endian format at 32-bit level (within MSW and LSW)
and thus need special handling.
2. No CCM (clock controller module) for QorIQ.
No CAAM clocks to enable / disable.
A new Kconfig option - CRYPTO_DEV_FSL_CAAM_LE - is added to indicate
CAAM is little endian (*). It is hidden from the user (to avoid
misconfiguration); when adding support for a new platform with LE CAAM,
either the Kconfig needs to be updated or the corresponding defconfig
needs to indicate that CAAM is LE.
(*) Using a DT property to provide CAAM endianness would not allow
for the ifdeffery.
In order to keep changes to a minimum, the following changes
are postponed:
-endianness fix of the last word in the S/G (rsvd2, bpid, offset),
fields are always 0 anyway;
-S/G format fix for i.MX7 (yes, i.MX7 support was not added yet,
but still...)
Signed-off-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Variable 'ret' is only used for returning the value 0.
We can make it simpler and just return 0 instead.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/returnvar.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In the error paths we should free the resources that were
previously acquired, so fix it accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When doing pointer operation for accessing the HW S/G table,
a value representing number of entries (and not number of bytes)
must be used.
Cc: <stable@vger.kernel.org> # 3.6+
Fixes: 045e36780f ("crypto: caam - ahash hmac support")
Signed-off-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Register only algorithms supported by CAAM hardware, using the CHA
version and instantiation registers to identify hardware capabilities.
Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com>
Tested-by: Horia Geantă <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Allow CAAM to be selected in the kernel for Freescale i.MX devices if
ARCH_MXC is enabled.
Signed-off-by: Steve Cornelius <steve.cornelius@freescale.com>
Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com>
Tested-by: Horia Geantă <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Avoid moving the head of the scatterlist entry by using temporary
pointers to walk the scatterlist.
Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com>
Tested-by: Horia Geantă <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Since fields must be ORed in to operate correctly using any order of
operations, changed allocations of the combination of extended
descriptor structs + hardware scatterlists to use kzalloc() instead
of kmalloc(), so as to ensure that residue data would not be ORed in
with the correct data.
Signed-off-by: Steve Cornelius <steve.cornelius@freescale.com>
Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com>
Tested-by: Horia Geantă <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Modify the Scatter-Gather entry definitions for the Freescale
CAAM driver to include support for both 64- and 32-bit DMA pointers.
Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com>
Tested-by: Horia Geantă <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
ARM-based systems may disable clocking to the CAAM device on the
Freescale i.MX platform for power management purposes. This patch
enables the required clocks when the CAAM module is initialized and
disables the required clocks when the CAAM module is shut down.
Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com>
Tested-by: Horia Geantă <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add set/clear 32-bit primitives for compatibility with ARM devices since
the primitives were previously only defined for the Power architecture.
Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com>
Tested-by: Horia Geantă <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Freescale i.MX6 ARM platforms do not support hardware cache coherency.
This patch adds cache coherency support to the CAAM driver.
Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com>
Tested-by: Horia Geantă <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch converts the authenc implementations in caam to the
new AEAD interface. The biggest change is that seqiv no longer
generates a random IV. Instead the IPsec sequence number is used
as the IV.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The encap shared descriptor was changed to use the new IV convention.
In the process some commands were shifted, making the output length
zero, caam effectively writing garbage in dst.
While here, update the decap descriptor to execute the "write" commands
before the "read"s (as it previously was).
This makes sure the input fifo is drained before becoming full.
Fixes: 46218750d5 ("crypto: caam - Use new IV convention")
Signed-off-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
An implicit truncation is done when using a variable of 64 bits
in MATH command:
warning: large integer implicitly truncated to unsigned type [-Woverflow]
Silence the compiler by feeding it with an explicit truncated value.
Signed-off-by: Tudor Ambarus <tudor.ambarus@freescale.com>
Signed-off-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When successful, the descriptor that performs RNG initialization
is allowed to return a status code of 7000_0000h, since last command
in the descriptor is a JUMP HALT.
Signed-off-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
HW coherency won't work properly for CAAM write transactions
if AWCACHE is left to default (POR) value - 4'b0001.
It has to be programmed to 4'b0010, i.e. AXI3 Cacheable bit set.
For platforms that have HW coherency support:
-PPC-based: the update has no effect; CAAM coherency already works
due to the IOMMU (PAMU) driver setting the correct memory coherency
attributes
-ARM-based: the update fixes cache coherency issues,
since IOMMU (SMMU) driver is not programmed to behave similar to PAMU
Signed-off-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In order to ensure that the ERA property is properly read from DT
on all platforms, of_property_read* function needs to be used.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch converts rfc4106 to the new calling convention where
the IV is now part of the AD and needs to be skipped.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull crypto update from Herbert Xu:
"Here is the crypto update for 4.2:
API:
- Convert RNG interface to new style.
- New AEAD interface with one SG list for AD and plain/cipher text.
All external AEAD users have been converted.
- New asymmetric key interface (akcipher).
Algorithms:
- Chacha20, Poly1305 and RFC7539 support.
- New RSA implementation.
- Jitter RNG.
- DRBG is now seeded with both /dev/random and Jitter RNG. If kernel
pool isn't ready then DRBG will be reseeded when it is.
- DRBG is now the default crypto API RNG, replacing krng.
- 842 compression (previously part of powerpc nx driver).
Drivers:
- Accelerated SHA-512 for arm64.
- New Marvell CESA driver that supports DMA and more algorithms.
- Updated powerpc nx 842 support.
- Added support for SEC1 hardware to talitos"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (292 commits)
crypto: marvell/cesa - remove COMPILE_TEST dependency
crypto: algif_aead - Temporarily disable all AEAD algorithms
crypto: af_alg - Forbid the use internal algorithms
crypto: echainiv - Only hold RNG during initialisation
crypto: seqiv - Add compatibility support without RNG
crypto: eseqiv - Offer normal cipher functionality without RNG
crypto: chainiv - Offer normal cipher functionality without RNG
crypto: user - Add CRYPTO_MSG_DELRNG
crypto: user - Move cryptouser.h to uapi
crypto: rng - Do not free default RNG when it becomes unused
crypto: skcipher - Allow givencrypt to be NULL
crypto: sahara - propagate the error on clk_disable_unprepare() failure
crypto: rsa - fix invalid select for AKCIPHER
crypto: picoxcell - Update to the current clk API
crypto: nx - Check for bogus firmware properties
crypto: marvell/cesa - add DT bindings documentation
crypto: marvell/cesa - add support for Kirkwood and Dove SoCs
crypto: marvell/cesa - add support for Orion SoCs
crypto: marvell/cesa - add allhwsupport module parameter
crypto: marvell/cesa - add support for all armada SoCs
...
The new aead_edesc_alloc left out the bit indicating the last
entry on the source SG list. This patch fixes it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
I incorrectly removed DESC_MAX_USED_BYTES when enlarging the size
of the shared descriptor buffers, thus making it four times larger
than what is necessary. This patch restores the division by four
calculation.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch fixes a number of problems in crypto driver Kconfig
entries:
1. Select BLKCIPHER instead of BLKCIPHER2. The latter is internal
and should not be used outside of the crypto API itself.
2. Do not select ALGAPI unless you use a legacy type like
CRYPTO_ALG_TYPE_CIPHER.
3. Select the algorithm type that you are implementing, e.g., AEAD.
4. Do not select generic C code such as CBC/ECB unless you use them
as a fallback.
5. Remove default n since that is the default default.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The patch
crypto: caam - Add definition of rd/wr_reg64 for little endian platform
added support for little endian platforms to the CAAM driver. Namely a
write and read function for 64 bit registers.
The only user of this functions is the Job Ring driver (drivers/crypto/caam/jr.c).
It uses the functions to set the DMA addresses for the input/output rings.
However, at least in the default configuration, the least significant 32 bits are
always in the base+0x0004 address; independent of the endianness of the bytes itself.
That means the addresses do not change with the system endianness.
DMA addresses are only 32 bits wide on non-64-bit systems, writing the upper 32 bits
of this value to the register for the least significant bits results in the DMA address
being set to 0.
Fix this by always writing the registers in the same way.
Suggested-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
