Enable all three capture channels, including the missing nid 7 which is
the only one capable of capturing DMIC input
Enable Headphone amp for the HP jack. This causes a volume boost for
headphones, but does not cause any noticeable effect for light loads
like other amps, so there is no need to make it configurable.
Add Input Mix capture mux setting to capture the output of the playback
input mux (that is, what goes out the speakers except for PCM)
Hack another coef register because the stereo DMIC for some reason
produces a nonstandard sum/difference signal. I found a bit to make it
just use the sum signal for both channels, which makes it behave like a
standard mono microphone. The stereo is useless anyway (they're 1cm apart).
Tested working: Three capture channels, mic in, line in, DMIC.
Tested not working: CD. Not sure why, might be unconnected in the actual
hardware or a CD drive issue.
Also looked at SPDIF. It appears to work (emitter lights up inside the
HP out jack) but I lack a proper miniTOSLINK cable to test it.
Signed-off-by: Hector Martin <hector@marcansoft.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The introduction of snd_card_set_id() added a lock on the card list
to the old choose_default_id() function when using it to implement
the new API call. This lock is needed to allow us to walk the list
and check to see if our new name is a duplicate. Unfortunately this
causes a lockup when called from snd_card_register() (in cases
where no ID is supplied for the card) since the card list is already
locked there.
Fix this fairly hideously by factoring out the implementation and
using a flag to indicate if the lock should be held. A better fix
would probably be to refactor snd_card_register() to move the
_set_id() outside the locking region but I can't immediately see
anything I can convince myself is safe.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Freescale eSDHC controller has the special order for
the HOST version register. that is not same as the other's
registers. The address of HOSTVER in spec is 0xFE, and
we need use the in_be16(0xFE) to access it, not in_be16(0xFC).
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Especially with Sandisk SDHC cards, the second SWITCH command was failing
with a timeout and the card was not recognized at all. However if the
system was busy, or debugging was enabled, or a udelay(100) was inserted
before the second SWITCH command in the core code, then the timing was
so that the card started to work.
With some unusual block sizes, the data FIFO status doesn't indicate a
"empty" state right away when the data transfer is done. Queuing
another data transfer in that condition results in a transfer timeout.
The empty FIFO bit eventually get set by itself in less than 50 usecs
when it is not set right away. So let's just poll for that bit before
configuring the controller with a new data transfer.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Empirical evidences show that this is causing far more problems than it
solves when this mode is enabled in the host hardware. Amongst those
cards that are known to be non functional when this bit is set are:
A-Data "Speedy" 2GB SD card
Kodak 512MB SD card
Ativa 1GB MicroSD card
Marvell 8688 (WIFI/Bluetooth) SDIO card
Since those cards do work on other host controllers which do honnor the
hs timing, the issue must be with this particular host hardware.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
disable_irq() should wait for all running handlers to complete
before returning. As such, if it's used to disable an interrupt
from that interrupt's handler it will deadlock. This replaces
the dangerous instances with the _nosync() variant which doesn't
have this problem.
Signed-off-by: Ben Nizette <bn@niasdigital.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
We plan to use fsl,esdhc going forward as the base compatible so update
the driver to bind against it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
When a software timeout occurs in polling mode hardware was left in
an indeterminate state causing subsequent operations to block.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
This is a temporary workaround until the MMC stack can be fixed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Fixes crash when shutting down.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove the __initdata annotation for the clock lookups, since they will
be needed when loading modules which use clk_get().
Tested-by: Agustín Ferrín Pozuelo <gatoguan-os@yahoo.com>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[I am not sure if this is the correct approach as I don't know if any of
this actual hardware or drivers are really hot pluggable.]
Gets rid of these build warnings:
WARNING: sound/ppc/snd-powermac.o(.devinit.text+0x5c): Section mismatch in reference from the function .snd_pmac_probe() to the function .init.text:.snd_pmac_new()
The function __devinit .snd_pmac_probe() references
a function __init .snd_pmac_new().
If .snd_pmac_new is only used by .snd_pmac_probe then
annotate .snd_pmac_new with a matching annotation.
WARNING: sound/ppc/snd-powermac.o(.devinit.text+0x10c): Section mismatch in reference from the function .snd_pmac_probe() to the function .init.text:.snd_pmac_burgundy_init()
The function __devinit .snd_pmac_probe() references
a function __init .snd_pmac_burgundy_init().
If .snd_pmac_burgundy_init is only used by .snd_pmac_probe then
annotate .snd_pmac_burgundy_init with a matching annotation.
WARNING: sound/ppc/snd-powermac.o(.devinit.text+0x164): Section mismatch in reference from the function .snd_pmac_probe() to the function .init.text:.snd_pmac_daca_init()
The function __devinit .snd_pmac_probe() references
a function __init .snd_pmac_daca_init().
If .snd_pmac_daca_init is only used by .snd_pmac_probe then
annotate .snd_pmac_daca_init with a matching annotation.
WARNING: sound/ppc/snd-powermac.o(.devinit.text+0x1dc): Section mismatch in reference from the function .snd_pmac_probe() to the function .init.text:.snd_pmac_tumbler_init()
The function __devinit .snd_pmac_probe() references
a function __init .snd_pmac_tumbler_init().
If .snd_pmac_tumbler_init is only used by .snd_pmac_probe then
annotate .snd_pmac_tumbler_init with a matching annotation.
WARNING: sound/ppc/snd-powermac.o(.devinit.text+0x1ec): Section mismatch in reference from the function .snd_pmac_probe() to the function .init.text:.snd_pmac_tumbler_post_init()
The function __devinit .snd_pmac_probe() references
a function __init .snd_pmac_tumbler_post_init().
If .snd_pmac_tumbler_post_init is only used by .snd_pmac_probe then
annotate .snd_pmac_tumbler_post_init with a matching annotation.
WARNING: sound/ppc/snd-powermac.o(.devinit.text+0x28c): Section mismatch in reference from the function .snd_pmac_probe() to the function .init.text:.snd_pmac_awacs_init()
The function __devinit .snd_pmac_probe() references
a function __init .snd_pmac_awacs_init().
If .snd_pmac_awacs_init is only used by .snd_pmac_probe then
annotate .snd_pmac_awacs_init with a matching annotation.
WARNING: sound/ppc/snd-powermac.o(.devinit.text+0x2bc): Section mismatch in reference from the function .snd_pmac_probe() to the function .init.text:.snd_pmac_pcm_new()
The function __devinit .snd_pmac_probe() references
a function __init .snd_pmac_pcm_new().
If .snd_pmac_pcm_new is only used by .snd_pmac_probe then
annotate .snd_pmac_pcm_new with a matching annotation.
WARNING: sound/ppc/snd-powermac.o(.devinit.text+0x2f8): Section mismatch in reference from the function .snd_pmac_probe() to the function .init.text:.snd_pmac_attach_beep()
The function __devinit .snd_pmac_probe() references
a function __init .snd_pmac_attach_beep().
If .snd_pmac_attach_beep is only used by .snd_pmac_probe then
annotate .snd_pmac_attach_beep with a matching annotation.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cut'n'paste mistake, whose likely result was nothing at all.
Correct version is "USB_DEVICE", not "USB_DEVICE_VENDOR_SPEC".
Signed-off-by: Andrea Borgia <andrea@borgia.bo.it>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, whenever an erratum workaround is enabled, it will be
applied whether or not the erratum is relevent for the CPU. This
patch changes this - we check the variant and revision fields in the
main ID register to determine which errata to apply.
We also avoid re-applying erratum 460075 if it has already been applied.
Applying this fix in non-secure mode results in the kernel failing to
boot (or even do anything.)
This fixes booting on some ARMv7 based platforms which otherwise
silently fail.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Define ARCH_KMALLOC_MINALIGN in asm/cache.h
At the request of Russell also move ARCH_SLAB_MINALIGN to this file.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ideally we should have a directory of drivers and a link to the 'active'
driver. For now just show the first device which is effectively the existing
semantics without a warning.
This is an update on the original buggy patch that I then forgot to
resubmit. Confusingly it was proposed by Red Hat, written by Etched Pixels
fixed and submitted by Intel ...
Resolves-Bug: http://bugzilla.kernel.org/show_bug.cgi?id=9749
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This matches Bartlomiej's patch for ide_pci_generic:
c339dfdd65
In the libata case netcell has its own mini driver. I suspect this fix is
actually only needed for some firmware revs but it does no harm either way.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: prevent deadlock in xfs_qm_shake()
xfs: fix overflow in xfs_growfs_data_private
xfs: fix double unlock in xfs_swap_extents()
Remove the limitation of PAGE_SIZE to be 4k by defining the own
page size and macros for 4k. 8kb page size could be natively supported,
but it's disabled right now for simplicity.
Also, clean up using upper_32_bits() macro.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The device seems supporting only U8, S16, S24_3LE, S32. Other linear
formats result in bad outputs.
Also, added the support for 32bit float format, which wasn't listed
in the original code.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
PCM names for surround streams should be also fixed as well as the mixer
element names. Also, a bit clean up for PCM name setup.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We usually pick up "Surround" mixer for the rear output, and "Side"
for the extra surround. Fix the channel mapping to follow it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The prepare callback can be called multiple times, thus it needs to
release and acquire the resource again by itself at the second or later
call.
Simply add pcm_release_resources() at the beginning of each prepare
callback in ctatc.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SNDRV_PCM_SUBCLASS_GENERIC_MIX is mostly for h/w multi-stream playback
devices, but ca0106 and emu10k1x don't support it (unlike emu10k1).
We shouldn't set that flag to avoid confusion.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If not passed as module option, provide an own card ID with the newly
introduced snd_set_card_id() call.
This will prevent ALSA from calling choose_default_name() which only
takes the last part of a name containing whitespaces. This for example
caused 'Audio 4 DJ' to be shortened to 'DJ', which was not very
descriptive.
The implementation now takes the short name and removes all whitespaces
from it which is much nicer.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Introduce snd_card_set_id() function to allow lowlevel drivers to set
default identification name for card slot. The function checks also
for identification name collisions and tries to create unique name.
Also, the snd_card_create() function is simplified, because this new
function is used. As bonus, proper name collision checks are evaluated
at the card create time.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Although the vmaster controls are created, they aren't registered thus
they don't appear in the real world. Added the missing snd_ctl_add()
calls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
This patch fixes a bug which unconfigured struct tcf_proto keeps
chaining in tc_ctl_tfilter(), and avoids kernel panic in
cls_cgroup_classify() when we use cls_cgroup.
When we execute 'tc filter add', tcf_proto is allocated, initialized
by classifier's init(), and chained. After it's chained,
tc_ctl_tfilter() calls classifier's change(). When classifier's
change() fails, tc_ctl_tfilter() does not free and keeps tcf_proto.
In addition, cls_cgroup is initialized in change() not in init(). It
accesses unconfigured struct tcf_proto which is chained before
change(), then hits Oops.
Signed-off-by: Minoru Usui <usui@mxm.nes.nec.co.jp>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Tested-by: Minoru Usui <usui@mxm.nes.nec.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Short story: this laptop has 5.1 built-in speakers which you *really*
want to use (the not-so-"sub" woofer is what makes the audio above
average for a laptop), so 6-channel support is important (plus a decent
asound.conf to upmix stereo). It also has the 3 typical jacks that ought
to have a selectable mode. And it's based on ALC889, which sucks.
Rationale/explanations:
The const_channel_count stuff was added because, for a laptop like this,
you always have 6 channels available (internal speakers) but still need
to set the mode for the 3 external jacks. Therefore, the device always
needs to be in 6-channel mode but there still needs to be a mixer
control for the jack mode. You could use line/mic-in at the same time as
the 6 internal speakers, for example. You might be tempted to make it
even smarter by dynamically switching the max channel count when
headphones are plugged in (therefore muting the internal speakers and
reducing the physical channel count to the jack channel mode), but as a
user I consider this to be harmful because I want the audio to blow up
to 6 channels / upmixed as soon as I unplug the headphones, and having
opened the device while in 2-channel mode would prevent this from
working (and always making 6-channel mode available doesn't do any harm).
The hardware needs EAPD turned on and the DACs routed to the internal
speaker pins, so the patch adds those verbs.
The ALC889 CLFE and subsequent (side/aux, here unused) DACs do NOT work
by default, at least here. I wasted much time trying to talk to
Realtek/pshou about this, but they just kept sending me useless updates
to patch_realtek.c that did nothing relevant. In the end I gave up and
brute forced the issue by trying to flip every bit in the proprietary
coefficient registers, and eventually found the two magic registers that
need to be cleared to enable all DACs. I have only heard Acer users
complain, but that might be because ALC889 is pretty new and using 5.1
(and noticing the missing center/lfe channels) might not be that common.
If this is a generalized issue with all ALC889 systems then those verbs
should probably be moved to a common verb array.
The internal mic is untested and probably doesn't work.
These settings will probably work for other Acer Gemstone laptops with
the same 5.1 speaker config. When identified, those should be added to
the PCI subsystem ID list.
Signed-off-by: Hector Martin <hector@marcansoft.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Patch to fix bad length checking in e1000. E1000 by default does two
things:
1) Spans rx descriptors for packets that don't fit into 1 skb on recieve
2) Strips the crc from a frame by subtracting 4 bytes from the length prior to
doing an skb_put
Since the e1000 driver isn't written to support receiving packets that span
multiple rx buffers, it checks the End of Packet bit of every frame, and
discards it if its not set. This places us in a situation where, if we have a
spanning packet, the first part is discarded, but the second part is not (since
it is the end of packet, and it passes the EOP bit test). If the second part of
the frame is small (4 bytes or less), we subtract 4 from it to remove its crc,
underflow the length, and wind up in skb_over_panic, when we try to skb_put a
huge number of bytes into the skb. This amounts to a remote DOS attack through
careful selection of frame size in relation to interface MTU. The fix for this
is already in the e1000e driver, as well as the e1000 sourceforge driver, but no
one ever pushed it to e1000. This is lifted straight from e1000e, and prevents
small frames from causing the underflow described above
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The serial number is of no interest in the longname, remove it. This
gives space for the usb path information which is more informative.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
