If the above is turned off then ipoib_cm_dev_init unconditionally
returns ENOSYS, and the newly added error handling in
0b3957 prevents ipoib from coming up at all:
kernel: mlx4_0: ipoib_transport_dev_init failed
kernel: mlx4_0: failed to initialize port 1 (ret = -12)
Fixes: 0b39578bcd (IB/ipoib: Use dedicated workqueues per interface)
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
T3 HW only supports 32 bit MRs. If the system uses 64 bit memory
addresses, then a registered 32 bit MR will wrap and write to the
wrong memory when used with addresses > 4GB. To prevent this,
simply fail to allocate an MR on 64 bit machines (other means
of registering memory are still available and software can still
work, we just don't allow this means of memory registration).
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
DMA transfers must be greater than the watermark level size. spi_imx->rx_wml
and spi_imx->tx_wml contain the watermark level in 32bit words whereas struct
spi_transfer contains the transfer len in bytes. Fix the check if DMA is
possible for a transfer accordingly. This fixes transfers with sizes between
33 and 128 bytes for which previously was claimed that DMA is possible.
Fixes: f62caccd12 (spi: spi-imx: add DMA support)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This change reverts most of commit 53e9accf0f 'Do not use R9 in
SYSCALL32'. I don't yet understand how, but code in that commit
sometimes fails to preserve EBP.
See https://bugzilla.kernel.org/show_bug.cgi?id=101061
"Problems while executing 32-bit code on AMD64"
Reported-and-tested-by: Krzysztof A. Sobiecki <sobkas@gmail.com>
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Will Drewry <wad@chromium.org>
Cc: Kees Cook <keescook@chromium.org>
CC: x86@kernel.org
Link: http://lkml.kernel.org/r/1437740203-11552-1-git-send-email-dvlasenk@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The BUG_ON() in purge_persistent_gnt() will be triggered when previous purge
work haven't finished.
There is a work_pending() before this BUG_ON, but it doesn't account if the work
is still currently running.
CC: stable@vger.kernel.org
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
We should consider info->feature_persistent when adding indirect page to list
info->indirect_pages, else the BUG_ON() in blkif_free() would be triggered.
When we are using persistent grants the indirect_pages list
should always be empty because blkfront has pre-allocated enough
persistent pages to fill all requests on the ring.
CC: stable@vger.kernel.org
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
There is a bug when migrate from !feature-persistent host to feature-persistent
host, because domU still thinks new host/backend doesn't support persistent.
Dmesg like:
backed has not unmapped grant: 839
backed has not unmapped grant: 773
backed has not unmapped grant: 773
backed has not unmapped grant: 773
backed has not unmapped grant: 839
The fix is to recheck feature-persistent of new backend in blkif_recover().
See: https://lkml.org/lkml/2015/5/25/469
As Roger suggested, we can split the part of blkfront_connect that checks for
optional features, like persistent grants, indirect descriptors and
flush/barrier features to a separate function and call it from both
blkfront_connect and blkif_recover
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The de-emphasis sampling rate selection is controlled by BIT[3:4] of
PCM1681_DEEMPH_CONTROL register. Do proper left shift to set it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Marek Belisko <marek.belisko@streamunlimited.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
pdev->dev.platform_data is not initialized if match is true in function
sdhci_pxav3_probe. Just local variable pdata is assigned the return value
from function pxav3_get_mmc_pdata().
static int sdhci_pxav3_probe(struct platform_device *pdev) {
struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data;
...
if (match) {
ret = mmc_of_parse(host->mmc);
if (ret)
goto err_of_parse;
sdhci_get_of_property(pdev);
pdata = pxav3_get_mmc_pdata(dev);
}
...
}
Signed-off-by: Jingju Hou <houjingj@marvell.com>
Fixes: b650352dd3df("mmc: sdhci-pxa: Add device tree support")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's not supported by driver anymore after using runtime pm
and there's no user of it, so delete it now.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: Johan Derycke <johan.derycke@barco.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After commit 8d86e4fccc ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()"),
we do not need those duplicated parsing anymore.
Note: fsl,cd-controller is also deleted due to the driver does
not support controller card detection anymore after switch to runtime pm.
And there's no user of it right now in device tree.
wp-gpios is kept because we're still support fsl,wp-controller,
so we need a way to check if it's gpio wp or controller wp.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: Johan Derycke <johan.derycke@barco.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Device tree provides option to specify the max freqency with property
"max-frequency" in dts and common parse function mmc_of_parse() will
parse it and use this value to set host->f_max to tell the MMC core
the maxinum frequency the host works.
However, current sdhci driver will finally overwrite this value with
host->max_clk regardless of the max-frequency property.
This patch makes sure not overwrite the max-frequency set from device
tree and do basic sanity check.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: Johan Derycke <johan.derycke@barco.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is an incremental fix of commit
e62bd351b("mmc: sdhci-esdhc-imx: Do not break platform data boards").
After commit 8d86e4fccc ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()"),
we do not need to run the check of boarddata->wp_type/cd_type/max_bus_width
again for dt platform since those are already handled by mmc_of_parse().
Current code only exclude the checking of wp_type for dt platform which
does not make sense.
This patch moves all non dt probe code into one function.
Besides, since we only support SD3.0/eMMC HS200 for dt platform, the
support_vsel checking and ultra high speed pinctrl state are also merged
into sdhci_esdhc_imx_probe_dt.
Then we have two separately probe function for dt and non dt type.
This can make the driver probe more clearly.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: Johan Derycke <johan.derycke@barco.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current card detect probe process is that when driver finds a valid
ESDHC_CD_GPIO, it will clear the quirk SDHCI_QUIRK_BROKEN_CARD_DETECTION
which is set by default for all esdhc/usdhc controllers.
Then host driver will know there's a valid card detect function.
Commit 8d86e4fccc ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()")
breaks GPIO CD function for dt platform that it will return directly
when find ESDHC_CD_GPIO for dt platform which result in the later wrongly
to keep SDHCI_QUIRK_BROKEN_CARD_DETECTION for all dt platforms.
Then MMC_CAP_NEEDS_POLL will be used instead even there's a valid
GPIO card detect.
This patch adds back this function and follows the original approach to
clear the quirk if find an valid CD GPIO for dt platforms.
Fixes: 8d86e4fccc ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()")
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: Johan Derycke <johan.derycke@barco.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Support for 8BIT bus with was added some time ago to sdhci-esdhc but
then missed to remove the 8BIT from the reserved bit mask which made
8BIT non functional.
Fixes: 66b50a0099 ("mmc: esdhc: Add support for 8-bit bus width and..")
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We should not call dma_free_coherent if host->adma_table is NULL,
otherwise may trigger panic.
Fixes: d1e49f77d7 ("mmc: sdhci: convert ADMA descriptors to a...")
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sometimes BADA, DEB or CEB error interrupts occur when sd card is
unplugged during data transfer. These interrupts are currently ignored
by the interrupt handler. But, this results in card not being
recognised on subsequent insertion. This is because mmcqd is waiting
forever for the data transfer(for which error occurred) to complete.
Fix this, by reporting BADA, DEB, CEB errors to mmc-core as -EILSEQ, so
that the core can do appropriate handling.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DTO/DCRC errors were not being informed to the mmc core since
commit ae4bf788ee ("mmc: omap_hsmmc: consolidate error report handling of
HSMMC IRQ"). This commit made sure 'end_trans' is never set on DTO/DCRC
errors. This is because after this commit 'host->data' is checked after
it has been cleared to NULL by omap_hsmmc_dma_cleanup().
Because 'end_trans' is never set, omap_hsmmc_xfer_done() is never invoked
making core layer not to be aware of DTO/DCRC errors. Because of this
any command invoked after DTO/DCRC error leads to a hang.
Fix this by checking for 'host->data' before it is actually cleared.
Fixes: ae4bf788ee ("mmc: omap_hsmmc: consolidate error report handling of
HSMMC IRQ")
CC: stable@vger.kernel.org
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The ChromeOS EC SPI transport driver has a dependency on OF because it
uses some OF helpers from the <linux/of.h> header. But there isn't a
need for an explicit dependency since the header has stub functions if
CONFIG_OF is not defined.
Also, MFD_CROS_EC_SPI already depends on MFD_CROS_EC which in turn has
a dependency on OF so in practice can't be selected without CONFIG_OF.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Chrome platform support depends on X86 || ARM because there are
only Chromebooks using those architectures. But only some drivers
depend on a given architecture, and the ones that do already have
a dependency on their specific Kconfig symbol entries.
An option is to also make CHROME_PLATFORMS depends on || COMPILE_TEST
but is more future proof to remove the dependency and let the drivers
be built in all architectures if possible to have more build coverage.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The PM runtime core by default assumes a chip is suspended when runtime
PM is enabled. Currently the arizona driver enables runtime PM when the
chip is fully active and then disables the DCVDD regulator at the end of
arizona_dev_init. This however has several problems, firstly the if we
reach the end of arizona_dev_init, we did not properly follow all the
proceedures for shutting down the chip, and most notably we never marked
the chip as cache only so any writes occurring between then and the next
PM runtime resume will be lost. Secondly, if we are already resumed when
we reach the end of dev_init, then at best we get unbalanced regulator
enable/disables at work we lose DCVDD whilst we need it.
Additionally, since the commit 4f0216409f7c ("mfd: arizona: Add better
support for system suspend"), the PM runtime operations may
disable/enable the IRQ, so the IRQs must now be enabled before we call
any PM operations.
This patch adds a call to pm_runtime_set_active to inform the PM core
that the device is starting up active and moves the PM enabling to
around the IRQ initialisation to avoid any PM callbacks happening until
the IRQs are initialised.
Cc: stable@vger.kernel.org # v3.5+
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The function arizona_irq_thread (the threaded handler for the arizona
IRQs) calls pm_runtime_get_sync at the start to ensure that the chip is
active as we handle the IRQ. If the chip is part way through a runtime
suspend when an IRQ arrives the PM core will wait for the suspend to
complete, before resuming. However, since commit 4f0216409f7c
("mfd: arizona: Add better support for system suspend") the runtime
suspend function may call disable_irq, if the chip is going to fully
power off, which will try to wait for any outstanding IRQs to complete.
This results in deadlock as the IRQ thread is waiting for the PM
operation to complete and the PM thread is waiting for the IRQ to
complete.
To avoid this situation we use disable_irq_nosync, which allows the
suspending thread to finish the suspend without waiting for the IRQ to
complete. This is safe because if an IRQ is being processed it can only
be blocked at the pm_runtime_get_sync at the start of the handler
otherwise it wouldn't be possible to suspend.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
As a follow up to ce31c1b0dc - there are
still a few LIO match_int() calls that don't check the return value.
Propagate errors rather than using the potentially uninitialised result.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Here are some more instances where we are returning 0 from a configfs
store function, the unintended result of which is likely infinite retries
from userspace.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
See https://bugzilla.redhat.com/show_bug.cgi?id=1240687
Returning 0 from a configfs store function results in infinite retries.
Reported-by: Yanko Kaneti <yaneti@declera.com>
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
API compliance scanning with coccinelle flagged:
./drivers/scsi/qla2xxx/tcm_qla2xxx.c:407:2-29:
WARNING: timeout is HZ dependent
This was introduced in 'commit 75f8c1f693 ("[SCSI] tcm_qla2xxx: Add >=
24xx series fabric module for target-core")'. wait_for_completion_timeout()
expects a timeout in jiffies so the numeric constant makes the effective
timeout HZ dependent. Resolved by converting it to CONST * HZ.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This flag is currently never cleared, which can in rare cases
trigger a warn-on if it is still set but the block isn't
InSync.
So clear it when it isn't need, which includes if the replacement
device has failed.
Signed-off-by: NeilBrown <neilb@suse.com>
During a node failure, We need to suspend read balancing so that the
reads are directed to the first device and stale data is not read.
Suspending writes is not required because these would be recorded and
synced eventually.
A new flag MD_CLUSTER_SUSPEND_READ_BALANCING is set in recover_prep().
area_resyncing() will respond true for the entire devices if this
flag is set and the request type is READ. The flag is cleared
in recover_done().
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Reported-By: David Teigland <teigland@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
bitmap_read_sb is modifying mddev->bitmap_info.offset. This works for
the first bitmap read. However, when multiple bitmaps need to be opened
by the same node, it ends up corrupting the offset. Fix it by using a
local variable.
Also, bitmap_read_sb is not required in bitmap_copy_from_slot since
it is called in bitmap_create. Remove bitmap_read_sb().
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NeilBrown <neilb@suse.com>
request_module() can return 256 (process exited) in some cases,
which is not as specified in the documentation before the
request_module() definition. Convert the error to -ENOENT.
The positive error number results in bitmap_create() returning
a value that is meant to be an error but doesn't look like one,
so it is dereferenced as a point and causes a crash.
(not needed for stable as this is "experimental" code)
Fixes: edb39c9ded ("Introduce md_cluster_operations to handle cluster functions")
Signed-off-By: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NeilBrown <neilb@suse.com>
If the bitmap read fails, the error code set is -EINVAL. However,
we don't check for errors and go ahead with cluster_setup.
Skip the cluster setup in case of error.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NeilBrown <neilb@suse.com>
