The mv88e6xxx_priv_state structure contains an fid_mask, where 1 means
the FID is free to use, 0 means the FID is in use.
This patch fixes the bit clear in mv88e6xxx_leave_bridge() when
assigning a new FID to a port.
Example scenario: I have 7 ports, port 5 is CPU, port 6 is unused (no
PHY). After setting the ports 0, 1 and 2 in bridge br0, and ports 3 and
4 in bridge br1, I have the following fid_mask: 0b111110010110 (0xf96).
Indeed, br0 uses FID 0, and br1 uses FID 3.
After setting nomaster for port 0, I get the wrong fid_mask: 0b10 (0x2).
With this patch we correctly get 0b111110010100 (0xf94), meaning port 0
uses FID 1, br0 uses FID 0, and br1 uses FID 3.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
ANY_LAYOUT is a compatibility feature. It's implied
for VERSION_1 devices, and non-transitional devices
might not offer it. Change code to behave accordingly.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull s390 fix from Martin Schwidefsky:
"Fast path fix for the thread_struct breakage"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: adapt entry.S to the move of thread_struct
Pull AVR32 update from Hans-Christian Egtvedt.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
AVR32/time: Migrate to new 'set-state' interface
If nfsd4_layout_setlease fails, nfsd will not put ls->ls_file.
Fix commit c5c707f96f "nfsd: implement pNFS layout recalls".
Signed-off-by: Kinglong Mee <kinglongmee@gmail.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
The dma_map_single and dma_unmap_single should set "gadget->dev.parent"
instead of "&gadget->dev" in the first argument because the parent has
a udc controller's device pointer.
Otherwise, iommu functions are not called in ARM environment.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There was an omission in transition to devm_xxx resource handling.
iounmap(udc->phy_regs) were removed, but ioremap() was left
without devm_.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Fixes: 3517c31a8e ("usb: gadget: mv_udc: use devm_xxx for probe")
Signed-off-by: Felipe Balbi <balbi@ti.com>
Phy drivers and the ulpi interface providers depend on the
registration of the ulpi bus. Ulpi registers the bus in
module_init(). This could cause unnecessary bus users'
probe delays. i.e. unnecessary -EPROBE_DEFER happening on
ulpi_drivers in case they're registered before ulpi bus
itself.
Reported-by: Zhuo Qiuxu <qiuxu.zhuo@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are configurations which may not have LDD/STD
Signed-off-by: Claudiu Zissulescu <claziss@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Simon Horman says:
====================
IPVS Fixes for v4.2
please consider this fix for v4.2.
For reasons that are not clear to me it is a bumper crop.
It seems to me that they are all relevant to stable.
Please let me know if you need my help to get the fixes into stable.
* ipvs: fix ipv6 route unreach panic
This problem appears to be present since IPv6 support was added to
IPVS in v2.6.28.
* ipvs: skb_orphan in case of forwarding
This appears to resolve a problem resulting from a side effect of
41063e9dd1 ("ipv4: Early TCP socket demux.") which was included in v3.6.
* ipvs: do not use random local source address for tunnels
This appears to resolve a problem introduced by
026ace060d ("ipvs: optimize dst usage for real server") in v3.10.
* ipvs: fix crash if scheduler is changed
This appears to resolve a problem introduced by
ceec4c3816 ("ipvs: convert services to rcu") in v3.10.
Julian has provided backports of the fix:
* [PATCHv2 3.10.81] ipvs: fix crash if scheduler is changed
http://www.spinics.net/lists/lvs-devel/msg04008.html
* [PATCHv2 3.12.44,3.14.45,3.18.16,4.0.6] ipvs: fix crash if scheduler is changed
http://www.spinics.net/lists/lvs-devel/msg04007.html
Please let me know how you would like to handle guiding these
backports into stable.
* ipvs: fix crash with sync protocol v0 and FTP
This appears to resolve a problem introduced by
749c42b620 ("ipvs: reduce sync rate with time thresholds") in v3.5
====================
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Quoting Daniel Borkmann:
"When adding connection tracking template rules to a netns, f.e. to
configure netfilter zones, the kernel will endlessly busy-loop as soon
as we try to delete the given netns in case there's at least one
template present, which is problematic i.e. if there is such bravery that
the priviledged user inside the netns is assumed untrusted.
Minimal example:
ip netns add foo
ip netns exec foo iptables -t raw -A PREROUTING -d 1.2.3.4 -j CT --zone 1
ip netns del foo
What happens is that when nf_ct_iterate_cleanup() is being called from
nf_conntrack_cleanup_net_list() for a provided netns, we always end up
with a net->ct.count > 0 and thus jump back to i_see_dead_people. We
don't get a soft-lockup as we still have a schedule() point, but the
serving CPU spins on 100% from that point onwards.
Since templates are normally allocated with nf_conntrack_alloc(), we
also bump net->ct.count. The issue why they are not yet nf_ct_put() is
because the per netns .exit() handler from x_tables (which would eventually
invoke xt_CT's xt_ct_tg_destroy() that drops reference on info->ct) is
called in the dependency chain at a *later* point in time than the per
netns .exit() handler for the connection tracker.
This is clearly a chicken'n'egg problem: after the connection tracker
.exit() handler, we've teared down all the connection tracking
infrastructure already, so rightfully, xt_ct_tg_destroy() cannot be
invoked at a later point in time during the netns cleanup, as that would
lead to a use-after-free. At the same time, we cannot make x_tables depend
on the connection tracker module, so that the xt_ct_tg_destroy() would
be invoked earlier in the cleanup chain."
Daniel confirms this has to do with the order in which modules are loaded or
having compiled nf_conntrack as modules while x_tables built-in. So we have no
guarantees regarding the order in which netns callbacks are executed.
Fix this by allocating the templates through kmalloc() from the respective
SYNPROXY and CT targets, so they don't depend on the conntrack kmem cache.
Then, release then via nf_ct_tmpl_free() from destroy_conntrack(). This branch
is marked as unlikely since conntrack templates are rarely allocated and only
from the configuration plane path.
Note that templates are not kept in any list to avoid further dependencies with
nf_conntrack anymore, thus, the tmpl larval list is removed.
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Tested-by: Daniel Borkmann <daniel@iogearbox.net>
When dom0 is being ballooned balloon_process() will hold the balloon
mutex until it is finished. This will block e.g. creation of new
domains as the device backends for the new domain need some
autoballooned pages for the ring buffers.
Avoid this by releasing the balloon mutex from time to time during
ballooning. Adjust the comment above balloon_process() regarding
multiple instances of balloon_process().
Instead of open coding it, just use cond_resched().
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
git commit 0c8c0f03e3
"x86/fpu, sched: Dynamically allocate 'struct fpu'"
moved the thread_struct to the end of the task_struct.
This causes some of the offsets used in entry.S to overflow their
instruction operand field. To fix this use aghi to create a
dedicated pointer for the thread_struct.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Being highly configurable core ARC HS among other features might be
configured with or without DIV_REM_OPTION (hardware divider).
That option when enabled adds following instructions: div, divu, rem, remu.
By default ARC HS38 has this option enabled. So we add here possibility
to disable usage of hardware divider by compiler.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Migrate arc driver to the new 'set-state' interface provided by
clockevents core, the earlier 'set-mode' interface is marked obsolete
now.
This also enables us to implement callbacks for new states of clockevent
devices, for example: ONESHOT_STOPPED.
Cc: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Migrate avr32 driver to the new 'set-state' interface provided by
clockevents core, the earlier 'set-mode' interface is marked obsolete
now.
This also enables us to implement callbacks for new states of clockevent
devices, for example: ONESHOT_STOPPED.
We want to call cpu_idle_poll_ctrl() in shutdown only if we were in
oneshot or resume state earlier. Create another variable to save this
information and check that in shutdown callback.
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Tests with a Sierra Wireless MC7355 have shown that 1199:9041 devices
also require the option_send_setup() code to be used on the USB
interface for the AT port to make unsolicited response codes work
correctly. Move these devices from the qcserial driver to the option
driver like it has been done for the 1199:68c0 devices in commit
d80c0d1418 ("USB: qcserial/option: make
AT URCs work for Sierra Wireless MC73xx").
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The param_val variable is what determines if schmitt
trigger is enabled on a pin or not. A typo here mean
that schmitt trigger was always enabled for standard
and i2c pins.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
imx1_pinconf_set assumes that the array of pins in struct
imx1_pinctrl_soc_info can be indexed by pin id to get the
pinctrl_pin_desc for a pin. This used to be correct up to commit
607af165c0 which removed some entries from the array and so made it
wrong to access the array by pin id.
The result of this bug is a wrong pin name in the output for small pin
ids and an oops for the bigger ones.
This patch is the result of a discussion that includes patches by Markus
Pargmann and Chris Ruehl.
Fixes: 607af165c0 ("pinctrl: i.MX27: Remove nonexistent pad definitions")
Cc: stable@vger.kernel.org
Reported-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's possible to hit a race condition if interrupts are generated on a GPIO
pin when the IRQ line in question is being disabled.
If the interrupt is freed, bcm2835_gpio_irq_disable() is called which
disables the event generation sources (edge, level). If an event occurred
between the last disabling of hard IRQs and the write to the event
source registers, a bit would be set in the GPIO event detect register
(GPEDSn) which goes unacknowledged by bcm2835_gpio_irq_handler()
so Linux complains loudly.
There is no per-GPIO mask register, so when disabling GPIO interrupts
write 1 to the relevant bit in GPEDSn to clear out any stale events.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PFC driver causes the kernel to hang on the R-Car gen2 SoC based boards
when the CPU_ALL_PORT() macro is fixed to reflect the reality, i.e. when the
GPIO space becomes actually sparse. This happens because the _GP_GPIO() macro
includes an indexed initializer which causes the "holes" (array entries filled
with all 0s) between the groups of the existing GPIOs; and the driver can't
cope with that. There seems to be no reason to use the indexed initializer,
so we can remove the index specifier and so avoid the "holes".
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit a21763a0b1
"pinctrl: nomadik: activate strict mux mode"
put all Nomadik pin controllers to strict mode. This was
not good on the Snowball platform: the muxing of GPIOs to
different pins is done with hogs in the DTS file, and then
these GPIOs are used by offset, relying on hogs to mux the
pins. Since that means the pin controller "owns" the pins
and at the same time we have a GPIO user, this pin controller
is by definition not strict.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When the controller is powered up but the HDMI codec is powered down
on Skylake, the power well is turned off. When the codec is then
powered up again, we need to poke the codec a little extra to make
sure it wakes up. Otherwise we'll get sad "no response from codec"
messages and broken audio.
This also changes azx_runtime_resume to actually call
snd_hdac_set_codec_wakeup for Skylake (before STATETS read).
(Otherwise it would only have been called for Haswell and Broadwell,
which both do not need it, so this probably was not the author's
intention.)
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Two fairly simple fixes: one is a change that causes us to have a very low
queue depth leading to performance issues and the other is a null deref
occasionally in tapes thanks to use after put.
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJVq2/DAAoJEDeqqVYsXL0MhqoH/2ZlycWVQ2ZQyC9k2UWjAS7t
By0ufRZKeaxgwriVWZqTCE3QHfqqeR5tNNSvk26k+CJTS6nyVGX+g8cxLQJf1gey
DyAi9za+5P5SwYFuJxzULyZddTyeshoZplVvRwjd1/gnRUJXybuO+HRkYzaROd5e
7snX56jGt1MzpmIrO2wln24pFLVfdC5JivzUcXgYecHD/XZuzOEdZE1dCxONXy27
rTeqYayIGLFo7vhSt9J9ViF0QiU6ahCKmQ/TDsv3Sq1zg228E7DAmlzVAo2NCwLM
gelTRHRdO4rwwkehZH8QIdUI77MzgmwQIU4nZp3FBG9SWrIEPHaRpiDxCHr3UE0=
=bfE2
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two fairly simple fixes: one is a change that causes us to have a very
low queue depth leading to performance issues and the other is a null
deref occasionally in tapes thanks to use after put"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: fix host max depth checking for the 'queue_depth' sysfs interface
st: null pointer dereference panic caused by use after kref_put by st_open
Pull MIPS fixes from Ralf Baechle:
"Another round of MIPS fixes for 4.2.
Things are looking quite decent at this stage but the recent work on
the FPU support took its toll:
- fix an incorrect overly restrictive ifdef
- select O32 64-bit FP support for O32 binary compatibility
- remove workarounds for Sibyte SB1250 Pass1 parts. There are rare
fixing the workarounds is not worth the effort.
- patch up an outdated and now incorrect comment"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: fpu.h: Allow 64-bit FPU on a 64-bit MIPS R6 CPU
MIPS: SB1: Remove support for Pass 1 parts.
MIPS: Require O32 FP64 support for MIPS64 with O32 compat
MIPS: asm-offset.c: Patch up various comments refering to the old filename.
Pull parisc fix from Helge Deller:
"A memory leak fix from Christophe Jaillet which was introduced with
kernel 4.0 and which leads to kernel crashes on parisc after 1-3 days"
* 'parisc-4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: mm: Fix a memory leak related to pmd not attached to the pgd
By far most of the fixes here are updates to DTS files to deal with some
mostly minor bugs.
There's also a fix to deal with non-PM kernel configs on i.MX, a
regression fix for ethernet on PXA platforms and a dependency fix for OMAP.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=SOgd
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"By far most of the fixes here are updates to DTS files to deal with
some mostly minor bugs.
There's also a fix to deal with non-PM kernel configs on i.MX, a
regression fix for ethernet on PXA platforms and a dependency fix for
OMAP"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: keystone: dts: rename pcie nodes to help override status
ARM: keystone: dts: fix dt bindings for PCIe
ARM: pxa: fix dm9000 platform data regression
ARM: dts: Correct audio input route & set mic bias for am335x-pepper
ARM: OMAP2+: Add HAVE_ARM_SCU for AM43XX
MAINTAINERS: digicolor: add dts files
ARM: ux500: fix MMC/SD card regression
ARM: ux500: define serial port aliases
ARM: dts: OMAP5: Add #iommu-cells property to IOMMUs
ARM: dts: OMAP4: Add #iommu-cells property to IOMMUs
ARM: dts: Fix frequency scaling on Gumstix Pepper
ARM: dts: configure regulators for Gumstix Pepper
ARM: dts: omap3: overo: Update LCD panel names
ARM: dts: cros-ec-keyboard: Add support for some Japanese keys
ARM: imx6: gpc: always enable PU domain if CONFIG_PM is not set
ARM: dts: imx53-qsb: fix TVE entry
ARM: dts: mx23: fix iio-hwmon support
ARM: dts: imx27: Adjust the GPT compatible string
ARM: socfpga: dts: Fix entries order
ARM: socfpga: dts: Fix adxl34x formating and compatible string
Acer Aspire V5 with the ALC282 codec is given the wrong value for the
0x19 PIN by the laptop's BIOS. Overriding it with the correct value
adds support for the headset microphone which would not otherwise be
visible in the system.
The fix is based on commit 7819717b11 with a similar quirk for Acer
Aspire with the ALC269 codec.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=96201
Cc: <stable@vger.kernel.org>
Signed-off-by: Mateusz Sylwestrzak <matisec7@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Data is stored in the device in be16 format. Make use of be16_to_cpu and
cpu_to_be16 to have correct endianness on any host architecture.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Reviewed-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
iio_device_register should be the last operation during probe. Therefor
move up interrupt setup code and while at it, change the check for invalid
values of client->irq to be smaller than zero.
Fixes: 3dd477acbd ("iio: light: Add threshold interrupt support for STK3310")
As the device_register makes the userspace interfaces of the device available
it is possible for requests to come in before the probe sequence has finished.
This can lead to unhandled interrupts and similar.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Reviewed-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
IIO_EV_TYPE_THRESH in rising direction describes an event where the
threshold is crossed in rising direction, positive or negative values
being possible. This is not the case here.
Since the threshold is no signed value and only the magnitude is compared,
IIO_EV_TYPE_MAG is what describes the behaviour of these devices, see the
sysfs-bus-iio ABI Documentation.
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
On reading in_voltage_scale of we got an NULL pointer dereference Oops.
The reason for this is, that mcp320x_read_raw tries to access
chip_info->resolution from struct mcp320x, but chip_info is never set.
chip_info was never set since the driver was added, but there was no
acute problem, because it was not referenced.
The acute problem exists since
b12206e917
iio: adc: mcp320x. Add support for more ADCs
This patch fixes the issue by setting chip_info in mcp320x_probe.
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@gmx.at>
Reviewed-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Read the register only when the adc register address is 4 byte aligned.
(rather than the other way around).
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Cc: <Stable.vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Changed the offset to negative as usual equation is: (raw +
offset)*scale and in this
case offset should be negative (as we deduct 273.15 Kelvin to get temperature
in Celsius).
Signed-off-by: Crt Mori <cmo@melexis.com>
Acked-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The RESET operation invoked in the last instance will align
in the natural way all 3 axis and the chip top view.
Without this, north and south are swapped.
Signed-off-by: Viorel Suman <viorel.suman@intel.com>
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes setting the SET/RESET bit in the REG_CTRL0
register.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
According to the debug/error string, the content of chip_id is supposed to
be output, rather than the return value of the previous operation.
Fixes: c91746a236 ("iio: magn: Add support for BMC150 magnetometer")
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
bmc150_magn makes use of REGMAP_I2C, so select it to build always without
errors.
Fixes: c91746a236 ("iio: magn: Add support for BMC150 magnetometer")
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Sometimes bssid can go null on failed association.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: <stable@vger.kernel.org> # v3.17+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes bssid can go null on failed association.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: <stable@vger.kernel.org> # v3.19+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
only SAMP_FREQ is writable
Will lead to SAMP_FREQ being written by any attempt to write
to the other exported attributes and hence a rather unexpected
result!
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
drivers/iio/proximity/sx9500.c: In function ‘sx9500_buffer_preenable’:
drivers/iio/proximity/sx9500.c:682: warning: ‘ret’ may be used uninitialized in this function
drivers/iio/proximity/sx9500.c: In function ‘sx9500_buffer_predisable’:
drivers/iio/proximity/sx9500.c:706: warning: ‘ret’ may be used uninitialized in this function
If active_scan_mask is empty, it will loop once more over all channels,
doing nothing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The use of regmap in commit 2f2c96338a requires REGMAP_I2C to be selected, in
order to meet all dependencies.
Fixes: 2f2c96338a ("iio: ltr501: Add regmap support.")
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
