commit 348c7cf5fcbcb68838255759d4cb45d039af36d2 upstream.
This change resolves a new compile-time warning
when built as a loadable module:
WARNING: modpost: missing MODULE_LICENSE() in drivers/power/reset/zx-reboot.o
see include/linux/module.h for more information
This adds the license as "GPL v2", which matches the header of the file.
MODULE_DESCRIPTION and MODULE_AUTHOR are also added.
Signed-off-by: Jesse Chan <jc@linux.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba52e75718784fda1b683ee0bfded72a0b83b047 upstream.
Reading both fault and status registers and logging any fault should
take priority over handling status register update.
Fix by moving the status handling to later in interrupt routine.
Fixes: d7bf353fd0 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68abfb8015832ddf728b911769659468efaf8bd9 upstream.
Caching the fault register after a single I2C read may not keep an accurate
value.
Fix by doing two reads in irq_handle_thread() and using the cached value
elsewhere. If a safety timer fault later clears itself, we apparently don't get
an interrupt (INT), however other interrupts would refresh the register cache.
From the data sheet: "When a fault occurs, the charger device sends out INT
and keeps the fault state in REG09 until the host reads the fault register.
Before the host reads REG09 and all the faults are cleared, the charger
device would not send any INT upon new faults. In order to read the
current fault status, the host has to read REG09 two times consecutively.
The 1st reads fault register status from the last read [1] and the 2nd reads
the current fault register status."
[1] presumably a typo; should be "last fault"
Fixes: d7bf353fd0 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d9fee6a42ea170e4378b3363a7ad385d0e67281 upstream.
We wrongly get uevents for bq24190-charger and bq24190-battery on every
register change.
Fix by checking the association with charger and battery before
emitting uevent(s).
Fixes: d7bf353fd0 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d62acc5ef0621463446091ebd7a345e06e9ab80c upstream.
The device specific data is not fully initialized on
request_threaded_irq(). This may cause a crash when the IRQ handler
tries to reference them.
Fix the issue by installing IRQ handler at the end of the probe.
Fixes: d7bf353fd0 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e05ad7e0741ce0505e1df157c62b22b95172bb97 upstream.
pm_resume() does a register_reset() which clears charger host mode.
Fix by calling set_mode_host() after the reset.
Fixes: d7bf353fd0 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 767eee362fd72bb2ca44cc80419ca4b38c6d8369 upstream.
The interrupt signal is TRIGGER_FALLING. This is is specified in the
data sheet PIN FUNCTIONS: "The INT pin sends active low, 256us
pulse to host to report charger device status and fault."
Also the direction can be seen in the data sheet Figure 37 "BQ24190
with D+/D- Detection and USB On-The-Go (OTG)" which shows a 10k
pull-up resistor installed for the sample configurations.
Fixes: d7bf353fd0 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b0408745e7ff24757cbfd571d69026c0ddb803c upstream.
LPDDR memories can only handle up to 400 uncontrolled power off. Ensure the
proper power off sequence is used before shutting down the platform.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0610735928ee47870e083d5901caa371089216f1 upstream.
bq->charger is initialized in bq24257_power_supply_init.
Therefore, bq24257_power_supply_init should be called before the
registration of the IRQ handler bq24257_irq_handler_thread that calls
power_supply_changed(bq->charger).
Signed-off-by: Georges Savoundararadj <savoundg@gmail.com>
Cc: Aurelien Chanot <chanot.a@gmail.com>
Cc: Andreas Dannenberg <dannenberg@ti.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Fixes: 2219a93596 ("power_supply: Add TI BQ24257 charger driver")
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5381cfb6f0422da24cfa9da35b0433c0415830e0 upstream.
The device's model download function returns the model data as
an array of u32s, which is later compared to the reference
model data. However, since the latter is an array of u16s,
the comparison does not happen correctly, and model verification
fails. This in turn breaks the POR initialization sequence.
Fixes: 39e7213edc ("max17042_battery: Support regmap to access device's registers")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sven Van Asbroeck <TheSven73@googlemail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5bc28b93a36e3cb3acc2870fb75cb6ffb182fece upstream.
Change power_supply_read_temp() to use power_supply_get_property()
so that it will check the use_cnt and ensure it is > 0. The use_cnt
will be incremented at the end of __power_supply_register, so this
will block to case where get_property can be called before the supply
is fully registered. This fixes the issue show in the stack below:
[ 1.452598] power_supply_read_temp+0x78/0x80
[ 1.458680] thermal_zone_get_temp+0x5c/0x11c
[ 1.464765] thermal_zone_device_update+0x34/0xb4
[ 1.471195] thermal_zone_device_register+0x87c/0x8cc
[ 1.477974] __power_supply_register+0x364/0x424
[ 1.484317] power_supply_register_no_ws+0x10/0x18
[ 1.490833] bq27xxx_battery_setup+0x10c/0x164
[ 1.497003] bq27xxx_battery_i2c_probe+0xd0/0x1b0
[ 1.503435] i2c_device_probe+0x174/0x240
[ 1.509172] driver_probe_device+0x1fc/0x29c
[ 1.515167] __driver_attach+0xa4/0xa8
[ 1.520643] bus_for_each_dev+0x58/0x98
[ 1.526204] driver_attach+0x20/0x28
[ 1.531505] bus_add_driver+0x1c8/0x22c
[ 1.537067] driver_register+0x68/0x108
[ 1.542630] i2c_register_driver+0x38/0x7c
[ 1.548457] bq27xxx_battery_i2c_driver_init+0x18/0x20
[ 1.555321] do_one_initcall+0x38/0x12c
[ 1.560886] kernel_init_freeable+0x148/0x1ec
[ 1.566972] kernel_init+0x10/0xfc
[ 1.572101] ret_from_fork+0x10/0x40
Also make the same change to ps_get_max_charge_cntl_limit() and
ps_get_cur_chrage_cntl_limit() to be safe. Lastly, change the return
value of power_supply_get_property() to -EAGAIN from -ENODEV if
use_cnt <= 0.
Fixes: 297d716f62 ("power_supply: Change ownership from driver to core")
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I2C is only required when using the config item BATTERY_BQ27XXX_I2C which
already depends on the I2C subsystem, remove the unneeded dependency from
BATTERY_BQ27XXX.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The IRQ handler is not used by the platform based
code resulting in a 'defined but not used' warning,
if CONFIG_BQ27XXX_I2C is not enabled.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Add missing initialization of register mapping table to
platform probe function.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Andrew F. Davis <afd@ti.com>
This driver fails to link without CONFIG_IIO, since
there are no stubs for the iio_channels functions.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Marek Belisko <marek@goldelico.com>
Acked-by: Nikolaus Schaller <hns@goldelico.com>
for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This adds power supply driver support for the Fuel-Gauge part of
the DA9150 combined Charger and Fuel-Gauge device.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds support for enabling/disabling optional device specific
features through sysfs properties at runtime.
* High-impedance mode enable/disable
* Sysoff enable/disable
Refer to the respective device datasheets for more information:
http://www.ti.com/product/bq24250http://www.ti.com/product/bq24251http://www.ti.com/product/bq24257
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch allows reading and writing of the input current limit through
the power supply's input_current_limit sysfs property. This allows
userspace to see what charger was detected (if the D+/D- USB signal-
based charger type detection is enabled) and to re-configure the maximum
current drawn from the external supply at runtime based on system-level
knowledge or user input. Note that upon charger disconnection and
re-connection the limit configured through firmware becomes active again
(or the D+/D- USB signal-based charger detection will be run again).
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
A new optional device property called "ti,in-dpm-voltage" is introduced
to allow configuring the input voltage threshold for the devices'
dynamic power path management (DPM) feature. In short, it can be used to
prevent the input voltage from dropping below a certain value as current
is drawn to charge the battery or supply the system.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
A new optional device property called "ti,ovp-voltage" is introduced to
allow configuring the input over voltage protection setting.
This commit also adds the basic sysfs support for custom properties
which is being used to allow userspace to read the current ovp-voltage
setting.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
A software-based approach for determining the charger's input voltage
"Power Good" state is introduced for devices like the bq24250 which
don't have a dedicated hardware pin for that purpose. This SW-based
approach is also used for other devices (with dedicated PG pin) as a
fall back solution if that pin is not configured to be used through
"pg-gpios".
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
A new optional device property called "ti,current-limit" is introduced
to allow disabling the D+/D- USB signal-based charger type auto-
detection algorithm used to set the input current limit and instead to
use a fixed input current limit.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Adding a missing bit definition for the sake of consistency device model
vs. bit field representation. No change in functionality.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch adds basic support for bq24250 and bq24251 which are very
similar to the bq24257 the driver was originally written for. Basic
support means the ability to select a device through Kconfig, DT and
ACPI, an instance variable allowing to check which chip is active, and
the reporting back of the selected device through the model_name power
supply sysfs property.
This patch by itself is not sufficient to actually use those two added
devices in a real-world setting due to some feature differences which
are addressed by other patches in this series.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Eliminate a few lines of code by using the PTR_ERR_OR_ZERO() macro.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use the devm_* managed version of the function to register the power
supply and remove the associated unregister function. This will simplify
error handling moving forward as it allows the unregister to happen
automatically. It also saves a few lines of code.
As this changes the order of putting the bq24257 into reset vs.
unregistering the power-supply during driver remove re-tested various
driver unload scenario to make sure that this doesn't cause any
unintended side effects such as erroneous interrupts.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The maximum amount of input current the charger should draw is dependent
on the power supply and should only be (re-)configured when the power
supply gets connected and disconnected. However the driver was also
lowering the bq24257's input current limit setting to 500mA when the
battery was removed and restored the previous setting according to the
power supply capabilities when the battery was reconnected although
these events are not impacting the amount of power that can be drawn
from the supply. Furthermore, a re-configuration of the input current
limit to 500mA when the battery gets disconnected is actually dangerous
if the limit was set higher previously and the system draws more than
500mA in which case the system voltage would be reduced in order to
maintain 500mA which could result in the system getting too low of a
supply to maintain operation. Last but not least the mechanism itself
used for battery re-connection detection did not work in corner cases
such as when the device's input current loop becomes active and the
bq24257 device clears its battery fault error resulting in incorrectly
reporting that the battery got reconnected.
This patches removes the impact the battery removal/insertion has on the
input current limit configured for the bq24257 and simplifies the
associated handler routine.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
At the time the driver was written GpioInt resources in ACPI were not
passed to the driver in client->irq, as opposed to DT enumeration. To
accommodate this use case, a "stat-gpios" property was introduced to
allow configuring the IRQ.
However this issue with ACPI was fixed in commit "845c877 i2c / ACPI:
Assign IRQ for devices that have GpioInt automatically" and makes this
workaround no longer necessary, hence we can remove the support for the
"stat-gpios" property and the associated code from the bq24257 driver.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
We need flags to be signed for the error handling to work.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Fixes: 74aab849f3 ('power: bq27xxx_battery: Cleanup health checking')
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-By: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
If either twl4030_charger or twl4030_madc is configured as MODULE,
we get build (link) errors.
To solve, the direct call of twl4030_get_madc_conversion() is replaced
by a call to iio_read_channel_processed().
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Since commit 1c6c69525b ("genirq: Reject bogus threaded irq requests")
threaded IRQs without a primary handler need to be requested with
IRQF_ONESHOT, otherwise the request will fail.
scripts/coccinelle/misc/irqf_oneshot.cocci detected this issue.
Fixes: b5874f33bb ("wm831x_power: Use genirq")
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch adds support for the tps65217 charger driver. This driver is
responsible for controlling the charger aspect of the tps65217 mfd.
Currently, this mainly consists of turning on and off the charger, but
some other features of the charger can be supported through this driver.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
"state" is a bool so it's never less than zero. The intent was to test
"ret" instead.
Fixes: 56d7df8716 ('power: Add Qualcomm SMBB driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Commit b68c316143 (bq2415x_charger: Allow to load and use driver even if
notify device is not registered yet) introduced null pointer dereference in
case bq is NULL. This patch fixes it.
Fixes: b68c316143 ("bq2415x_charger: Allow to load and use driver even if notify device is not registered yet")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Some devices have a pin that can generate an interrupt when
the battery's status changes. Add an interrupt handler to
read the new battery status.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Reorganize the logic checking battery health and add under temperature
condition checking.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add support for additional devices and register equivalent family devices
including the bq27010, bq27210, bq27500, bq27510, bq27520, bq27530,
bq27531, bq27541, bq27542, bq27546, bq27545, bq27441, bq27421, and the
bq27641.
To facilitate this process the register mapings have been moved to tables
and other small cleanups have been made.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Fix typos and change "relative state of charge" to "state of charge" as not
all supported devices use relative state of charge.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
When initialized as a platform device the initializer must now specify
a device. An empty device name is no longer valid.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Rename functions that are used by multiple devices. New devices
have been added and the function names and driver name are no longer
general enough for the functionality they provide.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: GUAN Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The MODULE_DEVICE_TABLE macro automatically adds all needed
i2c MODULE_ALIASes so remove the extra MODULE_ALIAS.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use managed resource function devm_power_supply_register instead
of power_supply_register to simplify the error path by allowing
unregister to happen automatically on error. To be compatible with
the change, replace various gotos by direct returns and remove
unneeded label err.
Also, remove max8998_battery_remove as it is now redundant.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use managed resource functions devm_request_threaded_irq and
devm_power_supply_register to simplify error handling.
To be compatible with the change, various gotos are replaced
with direct returns and unneeded labels are dropped. Also,
remove max8903_remove as it is now redundant.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
