For non-pluggable display, it should not enable HPD. Instead, the
bridge should handle all the clocks for HDMI. Also the scrambler
should be activated after the HDMI has power on the clock.
Change-Id: I9162a49b8f314de4d30b0d82c7867a639ddf05a6
Signed-off-by: Camus Wong <camusw@codeaurora.org>
Compile ADV7481 as a module, as part of kernel modularization
requirement.
Change-Id: Ie3e9669d05646503de6ddd3468cbd6da4ee4eae4
Suggested-by: Resmi Rajendran <resmir@qti.qualcomm.com>
Signed-off-by: Rahul Sharma <sharah@codeaurora.org>
In slave configuration "POWER_SUPPLY_PROP_CURRENT_MAX" fails to
suspend USB input path for 0/2mA current request. Fix this by
separately handling 0/2mA request to suspend input.
CRs-Fixed: 2148379
Change-Id: Id9b7887c4f2f924d9e4c8484947d74baa96eb8a3
Signed-off-by: Ashay Jaiswal <ashayj@codeaurora.org>
Current parallel design has fixed order of configuring
ICL/FCC between main and parallel charger, this could
lead to a situation where total(main + parallel) ICL/FCC
goes beyond maximum configured value.
Fix this by dynamic ordering of ICL/FCC between main and
parallel based on AICL change.
CRs-Fixed: 2148379
Change-Id: Ia1ff7093d1de9205ce8072760c80ba0a58638462
Signed-off-by: Ashay Jaiswal <ashayj@codeaurora.org>
Remove "qcom,mdss-dsi-on-command" and "mdss-dsi-off command"
commands for boot up performance optimization.
The two commands are for native DSI panels without a bridge
chip. However,AUTO platform has adv7533 bridge chip,which
is controlled by I2C instead of the above two commands.
In addition,the two command will cause extra wait for about
210ms in dsi_panel_tx_cmd_set() for dsi_display_enbale().
This make drmAtomicCommit() in libdrm a little slower,
so total boot time will be longer.
Change-Id: I848d189d4055b5626eadd809fc5da7c9c4ecbcce
Signed-off-by: Daocai <daocai@codeaurora.org>
In current HDMI driver, SVDs and DTDs derived from EDID
of a DS HDMI sink are checked for supportness based
on previous connection's max TMDS clock.
Always reset the max TMDS clock supported by source
before reading EDID from DS HDMI device.
Change-Id: If5f58562f186634b1ed066fdebfc9fa6b55c6e8a
Signed-off-by: Narender Ankam <nankam@codeaurora.org>
Hypervisor supports psci-1.0 not 0.1 and new function IDs
have been defined in psci driver.
Change-Id: Id257dd264f9ffc812879997c0b227e53f84c86a2
Signed-off-by: Yimin Peng <yiminp@codeaurora.org>
In the cmdq request issuing path, cq driver invokes ICE driver calls
to get the configuration for encrypting/decrypting the data requests.
The ice driver in-turn makes calls to secure world (TZ) which can
process only single task at a time. If TZ is busy in servicing
something else when ICE driver invokes it, ICE driver would return
-EBUSY to cmdq driver.
The requests which failed due to ice error are neither issued to h/w
nor errored out, so resulting in filesystem corruptions.
We must re-queue the requests which failed with -EBUSY error, so that
it will be re-issued again as very next request.
Change-Id: I4557a5c3aca8dd53740e48e516e6011787df50d8
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
During patch download of devices, size validations & zero alloc
the buffers to ensure values passed are in range
CRs-fixed: 2084692
Change-Id: Ie1cd76fe68766d6d12d7262202e48c18ebe42274
Signed-off-by: Balvinder Singh <bpsingh@codeaurora.org>
command-queue request may fail during preparation/issuing in some
cases. In case if it fails, the error code needs to be propagated back
to the function which initiated the request so that the request can be
handled appropriately.
Change-Id: Ia6946c14f0c106fb30bd70ca5c9e600c516fdf55
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Remove the runtime PM vote if command-queue request processing fails.
Otherwise, in case command-queue request preparation fails,
the runtime PM votes go out of sync and sdhc platform device suspend
might get blocked.
Change-Id: Ibe95e1653f7558a7994b606922a1625b429d57f6
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
During patch download procedure, size validation and zero
allocation of buffers are done to ensure values passed are
in permissible range
CRs-fixed: 2082452
Change-Id: I1c14e30f14af0279258efd0eadd8ab8ed6d8cf55
Signed-off-by: Balvinder Singh <bpsingh@codeaurora.org>
Following updates required to sync with remote client QMI
messaging for audio service:-
1) Add usb core id in disconnect indication to support multi
instance of remote client. Update uaudio_disconnect_cb() to send
usb core id.
3) Add USB_AUDIO_DEVICE_SPEED_SUPER_PLUS_V01 in to usb device
speed enum list. Update get_speed_info() API to reflect the same.
Change-Id: I2501c037e519454a4f84ec3c1ab9e423eb771544
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Since dcba dma address is not required by class driver
therefore remove the API definition.
Change-Id: I6851729f1ad4254bbfaf179755d9afa7870e8e01
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Since dcba dma address is not required by class driver
therefore remove the API definitions.
Change-Id: I2623cf3bf406ca0d47ea2549b5163d9e9b7351a1
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
dcba information passed to remote entity was only used to
get device speed. Instead of mapping dcba memory simply pass
enumerated device speed information in QMI response.
Change-Id: I5246b18ec1c5bfa1940b506d1de461f78eb14c6a
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
This allows to uniquely identify the multiple controllers
on MSM8996.
Change-Id: I99296cee886119e59af67e2d1a3983a28015b720
Signed-off-by: Ajay Agarwal <ajaya@codeaurora.org>
In order to support tunnel mode on multiple usb conttollers
qmi service needs to provide the controller number in
enable audio stream QMI response so that remote entity
programs appropriate usb controller to initiate data transfer
with USB audio device. Also, update QMI response message data
structure with optional speed_info.
Change-Id: I1d4968c19601a3984bf60e7754a6d88473540166
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Function provides controller id used by a remote entity
to identify which usb controller to program to initiate
data transfer.
Change-Id: Ied396f34496104c139a7910ee86844c124e6803f
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Function provides controller id used by a remote entity
to identify which usb controller to program to initiate
data transfer.
Change-Id: Ie700363c1a4a19aeb6b51305c97298f3b4d6e387
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Unique usb core id is used to differentiate between
different usb controllers.
Change-Id: Ibd886f704e7ecedfbf035b8e5adea2852ddf25bf
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Change Dest VM of SSC from 5 to 38 and it can be unmapped to
HLOS through hyp_assign.
Change-Id: I8e4ace8e9722d4fa79b553ad6b8d29353954f8c5
Signed-off-by: Tharun Kumar Merugu <mtharu@codeaurora.org>
Define data structure and callback for the ARP and NS offload
for the ath10k wcn3990 WLAN module. Configure the ARP offload
parameter and enable ARP offload request flag for each vdev
if the vdev in station mode.
This feature adds support to wakeup the device from sleep state
through wowlan event if the ARP request pattern matched with
pattern configured by WLAN module during wow suspend.
CRs-Fixed: 2146265
Change-Id: I54c3491493ad46a7db2adbf71ae1668cf9a88e51
Signed-off-by: Sarada Prasanna Garnayak <sgarna@codeaurora.org>
Floor vote data needs to be protected with mutex lock to
avoid double free of memory due to race condtion.
Change-Id: Ifaa01a14d273ccba6b9463aff3a41c0038b05f06
Signed-off-by: Odelu Kukatla <okukatla@codeaurora.org>
Currently we set the USB speed to SUPER after calling vbus/id
notifier callback. As a part of cable connect, is USB speed
is set to SUPER after connect resume_work is called, then we
do not initialise the SSPHY. So clocks are OFF.
But as part of cable disconnect, if USB speed is set to SUPER
before disconnect resume_work is called, then we try to
suspend SSPHY resulting in unclocked access.
Fix this by mandatorily setting USB speed to SUPER before
queuing VBUS/ID notifier.
Change-Id: Iac4411ddafd87909b1b26c9b5a8eb354a073d268
Signed-off-by: Ajay Agarwal <ajaya@codeaurora.org>
