According to Documentation/driver-model/devres.txt, devm_request_and_ioremap()
is deprecated, so use devm_ioremap_resource() instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The virtio spec requires byte 0 of the virtio-scsi LUN structure
to be '1'.
Signed-off-by: Venkatesh Srinivas <venkateshs@google.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Convert the uses of memcpy to ether_addr_copy because
for some architectures it is smaller and faster.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the more obvious uses of memcpy to ether_addr_copy.
There are still uses of memcpy that could be converted but
these addresses are __aligned(2).
Convert a couple uses of 6 in gr_private.h to ETH_ALEN.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_is_cwnd_limited() allows GSO/TSO enabled flows to increase
their cwnd to allow a full size (64KB) TSO packet to be sent.
Non GSO flows only allow an extra room of 3 MSS.
For most flows with a BDP below 10 MSS, this results in a bloat
of cwnd reaching 90, and an inflate of RTT.
Thanks to TSO auto sizing, we can restrict the bloat to the number
of MSS contained in a TSO packet (tp->xmit_size_goal_segs), to keep
original intent without performance impact.
Because we keep cwnd small, it helps to keep TSO packet size to their
optimal value.
Example for a 10Mbit flow, with low TCP Small queue limits (no more than
2 skb in qdisc/device tx ring)
Before patch :
lpk51:~# ./ss -i dst lpk52:44862 | grep cwnd
cubic wscale:6,6 rto:215 rtt:15.875/2.5 mss:1448 cwnd:96
ssthresh:96
send 70.1Mbps unacked:14 rcv_space:29200
After patch :
lpk51:~# ./ss -i dst lpk52:52916 | grep cwnd
cubic wscale:6,6 rto:206 rtt:5.206/0.036 mss:1448 cwnd:15
ssthresh:14
send 33.4Mbps unacked:4 rcv_space:29200
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: Van Jacobson <vanj@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool speed values are just numbers of megabits and there is no need
to add SPEED_40000. To be consistent, use integer constants directly
for all speeds.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lets clean up bpf_dbg a bit and improve its code slightly
in various areas: i) Get rid of some macros as there's no
good reason for keeping them, ii) remove one unused variable
and reduce scope of various variables found by cppcheck,
iii) Close non-default file descriptors when exiting the shell.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers are allowed to set NETIF_F_SCTP_CSUM if they have
hardware crc32c checksumming support for the SCTP protocol.
Currently, NETIF_F_SCTP_CSUM flag is available in igb,
ixgbe, i40e/i40evf drivers and for vlan devices.
If we don't have NETIF_F_SCTP_CSUM then crc32c is done
through CPU instructions, invoked from crypto layer, or
if not available as slow-path fallback in software.
Currently, loopback device propagates checksum offloading
feature flags in dev->features, but is missing SCTP checksum
offloading. Therefore, account for NETIF_F_SCTP_CSUM as
well.
Before patch:
./netperf_sctp -H 192.168.0.100 -t SCTP_STREAM_MANY
SCTP 1-TO-MANY STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.0.100 () port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
4194304 4194304 4096 10.00 4683.50
After patch:
./netperf_sctp -H 192.168.0.100 -t SCTP_STREAM_MANY
SCTP 1-TO-MANY STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.0.100 () port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
4194304 4194304 4096 10.00 15348.26
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_dma_desc_resources() returns an error value and the next line
actually checks for it, so assign the return value properly.
Found by the coverity scanner.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The documentation misses a few of the supported flags. Fix this. Also
respect the dependency to CONFIG_XFRM for the IPSEC flag.
Cc: Fan Du <fan.du@windriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'out' label is just a relict from previous times as pgctrl_write()
had multiple error paths. Get rid of it and simply return right away
on errors.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a privileged user writes an empty string to /proc/net/pktgen/pgctrl
the code for stripping the (then non-existent) '\n' actually writes the
zero byte at index -1 of data[]. The then still uninitialized array will
very likely fail the command matching tests and the pr_warning() at the
end will therefore leak stack bytes to the kernel log.
Fix those issues by simply ensuring we're passed a non-empty string as
the user API apparently expects a trailing '\n' for all commands.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shahed Shaikh says:
====================
qlcnic: Re-factoring and enhancements
This patch series includes following changes -
* Re-factored firmware minidump template header handling
* Support to make 8 vNIC mode application to work with 16 vNIC mode
* Enhance error message logging when adapter is in failed state and
when adapter lock access fails.
* Allow vlan0 traffic
* update MAINTAINERS
Please apply this series to net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep myself as only maintainer for qlcnic driver and update
group email alias to Dept-HSGLinuxNICDev@qlogic.com
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Adapter allows vlan0 traffic in case of SR-IOV after setting
QLC_SRIOV_ALLOW_VLAN0 bit even though we do not add vlan0 filters.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Qlogic application interface in the driver which has larger than 8 vNIC
configuration support has been updated to handle the following cases:
o Only 8 or lower total vNICs were enabled within the vNIC 0-7 range
o vNICs were enabled in the vNIC 0-15 range such that enabled vNICs were
not contiguous and only 8 or lower number of total VNICs were enabled
o Disconnect in the vNIC mapping between application and driver when the
enabled VNICs were dis contiguous
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Treat firmware minidump template headers for 82xx and 83xx/84xx adapters separately,
as it may change for 82xx and 83xx/84xx adapter type independently.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amir Vadai says:
====================
net/mlx4: Mellanox driver update 01-01-2014
This small patchset has a fix to a bogus usage of
netif_get_num_default_rss_queues() in mlx4_en driver.
Changes from V1:
- Removed affinity_hint patch, to make it a generic instead of mlx specific
Changes from V0:
- Instead of reverting the netif_get_num_default_rss_queues() in mlx4_en,
fixing it to limit the actual number of receive queues instead of limiting
the number of IRQ's.
Patchset was applied and tested against commit: cb6e926 "ipv6:fix checkpatch
errors with assignment in if condition"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This fix a performance bug introduced by commit 90b1ebe "mlx4: set
maximal number of default RSS queues", which limits the numbers of IRQs
opened by core module.
The limit should be on the number of queues in the indirection table -
rx_rings, and not on the number of IRQ's. Also, limiting on mlx4_core
initialization instead of in mlx4_en, prevented using "ethtool -L" to
utilize all the CPU's, when performance mode is prefered, since limiting
this number to 8 reduces overall packet rate by 15%-50% in multiple TCP
streams applications.
For example, after running ethtool -L <ethx> rx 16
Packet rate
Before the fix 897799
After the fix 1142070
Results were obtained using netperf:
S=200 ; ( for i in $(seq 1 $S) ; do ( \
netperf -H 11.7.13.55 -t TCP_RR -l 30 &) ; \
wait ; done | grep "1 1" | awk '{SUM+=$6} END {print SUM}' )
CC: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_en_add() is too long.
Moving set number of RX rings to a utiltity function to improve
readability and modulization of the code.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bond_xxx_info_query() was already in RTNL, so no need to use
bond lock to protect the bond slave list, so remove it.
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bond_info_show_master already in RCU read-side critical section,
and the we access curr_active_slave without the curr_slave_lock, we
could not sure whether the curr_active_slave will be changed during
the processing, so use RCU to protected the pointer.
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __netpoll_setup() will check the slave's flag and ndo_poll_controller just
like the slave_dev_support_netpoll() does, and slave_dev_support_netpoll() was
not used by any place, so remove it.
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should alloc big buffers also when guest can receive UFO
packets to let the big packets fit into guest rx buffer.
Fixes 5c5167515d
(virtio-net: Allow UFO feature to be set and advertised.)
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes stray access to undefined registers, use of wrong clock parents &
running clocks at wrong rates. All of these issues cause regressions in
the form of boards that are unable to boot or crash and die horrible
deaths.
Steffen Klassert says:
====================
1) Introduce skb_to_sgvec_nomark function to add further data to the sg list
without calling sg_unmark_end first. Needed to add extended sequence
number informations. From Fan Du.
2) Add IPsec extended sequence numbers support to the Authentication Header
protocol for ipv4 and ipv6. From Fan Du.
3) Make the IPsec flowcache namespace aware, from Fan Du.
4) Avoid creating temporary SA for every packet when no key manager is
registered. From Horia Geanta.
5) Support filtering of SA dumps to show only the SAs that match a
given filter. From Nicolas Dichtel.
6) Remove caching of xfrm_policy_sk_bundles. The cached socket policy bundles
are never used, instead we create a new cache entry whenever xfrm_lookup()
is called on a socket policy. Most protocols cache the used routes to the
socket, so this caching is not needed.
7) Fix a forgotten SADB_X_EXT_FILTER length check in pfkey, from Nicolas
Dichtel.
8) Cleanup error handling of xfrm_state_clone.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Releasing the touchscreen lets the internal statemachine left in a wrong state.
Due to this the release coordinate will be reported again by accident when the next
touchscreen event happens. This change sets up the correct state when waiting
for the next touchscreen event.
This has led to reported issues with calibrating the touchscreen.
Bug was introduced somewhere in the series that began with
18da755de5
Staging/iio/adc/touchscreen/MXS: add proper clock handling
in which the way this driver worked was substantially changed
to be interrupt driven rather than relying on a busy loop.
This was a regression in the 3.13 kernel.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
A selective retransmission request (SRR) is a fibre-channel
protocol control request which provides support for requesting
retransmission of a data sequence in response to an issue such as
frame loss or corruption. These events are experienced
infrequently in fibre-channel based networks which makes
it difficult to test and assess codepaths which handle these
events.
We were fortunate enough, for some definition of fortunate, to
have a metro-area single-mode SAN link which, at 10 GBPS
sustained load levels, would consistently generate SRR's in
a SCST based target implementation using our SCST/in-kernel
Qlogic target interface driver. In response to an SRR the
in-kernel Qlogic target driver immediately panics resulting
in a catastrophic storage failure for serviced initiators.
The culprit was a debug statement in the qla_target.c file which
does not verify that a pointer to the SCSI CDB is not null.
The unchecked pointer dereference results in the kernel panic
and resultant system failure.
The other two references to the SCSI CDB by the SRR handling code
use a ternary operator to verify a non-null pointer is being
acted on. This patch simply adds a similar test to the implicated
debug statement.
This patch is a candidate for any stable kernel being maintained
since it addresses a potentially catastrophic event with
minimal downside.
Signed-off-by: Dr. Greg Wettstein <greg@enjellic.com>
Cc: <stable@vger.kernel.org> #3.5+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When passing tx frames to the U-APSD queue for powersave poll responses,
the ath_atx_tid pointer needs to be passed to ath_tx_setup_buffer for
proper sequence number accounting.
This fixes high latency and connection stability issues with ath9k
running as AP and a few kinds of mobile phones as client, when PS-Poll
is heavily used
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both libertas USB driver and mwifiex_usb driver are registerring
with name 'usb8xxx'. The following conflict happens while trying
to load both drivers.
[6.211307] Error: Driver 'usb8xxx' is already registered...
[6.217261] mwifiex_usb: Driver register failed!
Fix it by renaming mwifiex_usb driver's name.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We only have one candidate for 3.14 fixes, and this is a NCI NULL
pointer dereference introduced during the 3.14 merge window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mfxv
-----END PGP SIGNATURE-----
Merge tag 'nfc-fixes-3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-fixes
Samuel Ortiz <sameo@linux.intel.com> says:
"NFC: 3.14: First pull request
We only have one candidate for 3.14 fixes, and this is a NCI NULL
pointer dereference introduced during the 3.14 merge window."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
dm_pool_close_thin_device() must be called if dm_set_target_max_io_len()
fails in thin_ctr(). Otherwise __pool_destroy() will fail because the
pool will still have an open thin device:
device-mapper: thin metadata: attempt to close pmd when 1 device(s) are still open
device-mapper: thin: __pool_destroy: dm_pool_metadata_close() failed.
Also, must establish error code if failing thin_ctr() because the pool
is in fail_io mode.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Cc: stable@vger.kernel.org
Pull SELinux endianness fix from James Morris.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
SELinux: bigendian problems with filename trans rules
Pull s390 bug fixes from Martin Schwidefsky:
"A couple of s390 bug fixes. The PCI segment boundary issue is a nasty
one as it can lead to data corruption"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/cio: Fix missing subchannels after CHPID configure on
s390/pci/dma: use correct segment boundary size
s390/compat: fix sys_sched_getattr compat wrapper
s390/zcrypt: additional check to avoid overflow in msg-type 6 requests
Stephane reported that perf report and annotate failed to process data
using lots of (> 500) shared libraries. It was because of the limit on
number of open files (ulimit -n).
Currently when perf loads a DSO, it'll look for normal and dynamic
symbol tables. And if it fails to find out both tables, it'll iterate
all of possible symtab types. But many of them are useless since they
have no additional information and the problem is that it's not closing
those files even though they're not used. Fix it.
Reported-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: Cody P Schafer <cody@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1392859976-32760-2-git-send-email-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The TUI of perf report and top support annotation, but stdio and GTK
don't. So it should be checked before calling hist_entry__inc_addr_
samples() to avoid wasting resources that will never be used.
perf annotate need it regardless of UI and sort keys, so the check
of whether to allocate resources should be on the tools that have
annotate as an option in the TUI, 'report' and 'top', not on the
function called by all of them.
It caused perf annotate on ppc64 to produce zero output, since the
buckets were not being allocated.
Reported-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1392859976-32760-1-git-send-email-namhyung@kernel.org
[ Renamed (report,top)__needs_annotate() to ui__has_annotation() ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The DT bindings document a renesas,indices property, while the code, the
DT example and the DT sources all use renesas,clock-indices. Fix the
documentation.
The shmobile mstp DT bindings have been merged in v3.14-rc1 with a bug
in the DT ABI, a fix during the -rc series is appropriate.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms@verge.net.au>
The qspi clock divisor is incorrectly set to twice the value it should
have, possibly because it has been computed based on PLL1 as the clock
parent instead of PLL1 / 2 (the datasheets specifies the qspi nominal
frequencies, not the divisor values). Fix it.
This bug introduced in v3.14-rc1 breaks various devices on the Lager and
Kolesh shmobile boards and should thus be considered as a regression for
which a fix during the -rc series is appropriate.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
The lb, qspi, sdh, sd0 and sd1 clocks have the PLL1 (divided by 2) as
their parent, not the main clock. Fix it.
This bug introduced in v3.14-rc1 breaks various devices on the Lager and
Kolesh shmobile boards and should thus be considered as a regression for
which a fix during the -rc series is appropriate.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
The MLME code in mac80211 must track whether or not the AP changed
bandwidth, but if there's no change while tracking it shouldn't do
anything, otherwise regulatory updates can make it impossible to
connect to certain APs if the regulatory database doesn't match the
information from the AP. See the precise scenario described in the
code.
This still leaves some possible problems with CSA or if the AP
actually changed bandwidth, but those cases are less common and
won't completely prevent using it.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=70881
Cc: stable@vger.kernel.org
Reported-and-tested-by: Nate Carlson <kernel@natecarlson.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- allow booting xtfpga on boards with new uBoot and >128MBytes memory;
- drop nonexistent GPIO32 support from fsf variant;
- don't select USE_GENERIC_SMP_HELPERS;
- enable common clock framework support, set up ethoc clock on xtfpga;
- wire up sched_setattr and sched_getattr syscalls.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XS4m
-----END PGP SIGNATURE-----
Merge tag 'xtensa-for-next-20140221-1' into for_next
Xtensa fixes for 3.14:
- allow booting xtfpga on boards with new uBoot and >128MBytes memory;
- drop nonexistent GPIO32 support from fsf variant;
- don't select USE_GENERIC_SMP_HELPERS;
- enable common clock framework support, set up ethoc clock on xtfpga;
- wire up sched_setattr and sched_getattr syscalls.
Signed-off-by: Chris Zankel <chris@zankel.net>
A collection of fixes for ARM platforms. Most are fixes for DTS files,
mostly from DT conversion on OMAP which is still finding a few issues here
and there.
There's a couple of small stale code removal patches that we usually
queue for the next release instead, but they seemed harmless enough to
bring in now.
Also, a fix for backlight on some PXA platforms, and a cache configuration
fix for Tegra, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=i7LS
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A collection of fixes for ARM platforms. Most are fixes for DTS
files, mostly from DT conversion on OMAP which is still finding a few
issues here and there.
There's a couple of small stale code removal patches that we usually
queue for the next release instead, but they seemed harmless enough to
bring in now.
Also, a fix for backlight on some PXA platforms, and a cache
configuration fix for Tegra, etc"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (25 commits)
MAINTAINERS: add additional ARM BCM281xx/BCM11xxx maintainer
ARM: tegra: only run PL310 init on systems with one
ARM: tegra: Add head numbers to display controllers
ARM: imx6: build pm-imx6q.c independently of CONFIG_PM
ARM: tegra: fix RTC0 alias for Cardhu
ARM: dove: dt: revert PMU interrupt controller node
Documentation: dt: OMAP: Update Overo/Tobi
ARM: dts: Add support for both OMAP35xx and OMAP36xx Overo/Tobi
ARM: dts: omap3-tobi: Use the correct vendor prefix
ARM: dts: omap3-tobi: Fix boot with OMAP36xx-based Overo
ARM: OMAP2+: Remove legacy macros for zoom platforms
ARM: OMAP2+: Remove MACH_NOKIA_N800
ARM: dts: N900: add missing compatible property
ARM: dts: N9/N950: fix boot hang with 3.14-rc1
ARM: OMAP1: nokia770: enable tahvo-usb
ARM: OMAP2+: gpmc: fix: DT ONENAND child nodes not probed when MTD_ONENAND is built as module
ARM: OMAP2+: gpmc: fix: DT NAND child nodes not probed when MTD_NAND is built as module
ARM: dts: omap3-gta04: Fix mmc1 properties.
ARM: dts: omap3-gta04: Fix 'aux' gpio key flags.
ARM: OMAP2+: add missing ARCH_HAS_OPP
...
