In order to satisfy all the various Kconfig options between
USB and DRM, we need to split the USB code out into a separate module
and export symbols to it.
This fixes build problems in -next reported by sfr.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch is applying some hunks that are already at changeset
c247d7b, causing a compilation breakage.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
stb0899: fix the limits for signal strength values
stb0899_read_signal_strength() adds an offset to the result of the table lookup.
That offset must correspond to the lowest value in the lookup table, to make sure
the result doesn't get below 0, which would mean a "very high" value since the
parameter is unsigned.
'strength' and 'snr' need to be initialized to 0 to make sure they have a
defined result in case there is no "internal->lock".
Signed-off-by: Klaus Schmidinger <Klaus.Schmidinger@tvdr.de>
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is mostly copy/paste of the 520e code with setting GPIO7 removed
(no LED light).
I've worked on just released vanilla linux-3.3.0 kernel, so there may
be 1/2 lines offset to the internal working source, but most of the
code should apply cleanly.
I was able to get the DVB-C working (tuned and watched TV). Haven't
tested DVB-T (no signal atm).
Special thanks to everybody who worked on the code and to Antti
Palosaari and Devin Heitmueller who provided essential support on irc.
Hardware is based of:
Empia EM2884
Micronas DRX 3926K
NXP TDA18271HDC2
AVF4910 (not used atm)
Signed-off-by: Ivan Kalvachev <ikalvachev@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hardware is based of:
Empia EM2884
Micronas DRX 3926K
NXP TDA18271HDC2
... + analog parts.
Analog is not supported currently. Only DVB-T and DVB-C.
There seems to be still problems for locking DVB-C channels which have
strong signal. Attenuator helps. I think it is demodulator IF/RF AGC
issue. Lets fix it later. Patches are welcome.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I found one more place where -EINVAL is used instead of -ENOTTY:
Note that drivers/media/dvb/dvb-core/dvbdev.c has the same code, but as far as
I can tell DVB is still using -EINVAL for unknown ioctls so I didn't change
that.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bridge register 1061 may take only the values 01 (stop) or 03 (start).
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The JPEG compression may be adjusted from the packet fill ratio and from
the flag 'USB FIFO full' returned in each frame.
The code is adapted from the one in gspca sonixj and uses a workqueue.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new functions i2c_w1_buf() and i2c_w2_buf() handle the write loops.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The JPEG compression quality was hardcoded to 95%. This value was too big,
raising often buffer overflows.
This quality is now 80% by default and is settable.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The reset of the Omnivision sensors takes a long time (200ms).
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The frame header was checked on packets of size 64 bytes only, while the webcams
may put a frame header at the beginning of bigger packets.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The line defining the value of the register 08 for the sensor cs2102k was
commented by error in commit 30c73d46.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds brightness control to the OmniVision 5621 sensor.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is adapted from Sylwester's patch proposed on 2012/02/22.
The JPEG compression control does not work with the autoquality done for the
sensors hv7131r and pas202b.
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The D1F5 revision of the WinTV HVR-1900 uses a tda18271c2 tuner
instead of a tda18271c1 tuner as used in revision D1E9. To
account for this, we must hardcode the frontend configuration
to use the same IF frequency configuration for both revisions
of the device.
6MHz DVB-T is unaffected by this issue, as the recommended
IF Frequency configuration for 6MHz DVB-T is the same on both
c1 and c2 revisions of the tda18271 tuner.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Mike Isely <isely@pobox.com>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove unnecessary register access in mxl111sf_ep6_streaming_ctrl()
This code breaks driver operation in kernel 3.3 and later, although
it works properly in 3.2 Disable register access to 0x12 for now.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hardware is based of:
Empia EM2874B
Micronas DRX 3913KA2
NXP TDA18271HDC2
Only DVB-C supported currently since missing firmware.
According to my tests, DRX 3913KA2 demodulator requires firmware
in order to support DVB-T mode.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We still need to power up the controller to avoid unsightly self-immolation
should something try to access its registers, but the sensor can stay
powered down unless the camera was actually operating at suspend time.
This gets rid of the camera LED flash on resume, fixing OLPC bug #11644.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is only one frame known to the DMA engine in scatter/gather mode, but
it still tells us that any or all of frames 1-3 are done at each completion
interrupt. Avoid the creation of junk frames by being sure to only
"complete" one on each interrupt.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I had learned through hard experience that dinking around with the DMA
descriptors while the C1_DESC_ENA enable bit was set is a recipe for all
kinds of truly malicious behavior on the hardware's part, regardless of
whether the DMA engine is actually operating at the time. That
notwithstanding, the driver did so dink, resulting in "green frame"
captures and the death of the system in random, spectacular ways.
Move the tweaking of C1_DESC_ENA to the same function that sets the
descriptor so we know that we'll never try to set a descriptor while that
bit is set.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Experience shows that, on the Armada platform, it can take as much as 120ms
for the DMA engine to actually shut down after it has been told to. So a
40ms timeout is not adequate; use 150ms instead. Also make sure we don't
leave the DMA_ACTIVE flag set once things are down.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The marvell cam driver retained just enough of the owner-tracking logic
from cafe_ccic to be broken; it could, conceivably, cause the driver to
release DMA memory while the controller is still active. Simply remove the
remaining pieces and ensure that the controller is stopped before we free
things.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The controller stop/restart logic could possibly restart DMA after the
driver things things have stopped, with suitably ugly results. Make sure
that we only restart the hardware if we're supposed to be streaming.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds clk_prepare/clk_unprepare calls to the pxa_camera
driver by using the helper functions clk_prepare_enable and
clk_disable_unprepare.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Newer CEU versions, e.g., the one, used on sh7372, support image sizes
larger than 2560x1920. Retrieve maximum sizes from platform properties.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
soc_camera_power_on() calls client's .s_power(1) method, which can try to
access the client hardware. This, however, is typically only possible,
after calling host's .add() method, because that's where the host driver
usually turns the master clock on.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This changes rc_core to not load the IR decoders at load time,
postponing it to load only if a RC_DRIVER_IR_RAW device is
registered via rc_register_device.
We use a static boolean variable, to ensure decoders modules
are only loaded once.
Tested with rc-loopback device only.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Call sequence:
tomoyo_write_domain() --> tomoyo_delete_domain()
In 'tomoyo_delete_domain', return -EINTR if locking attempt is
interrupted by signal.
At present it returns success to its caller 'tomoyo_write_domain()'
even though domain is not deleted. 'tomoyo_write_domain()' assumes
domain is deleted and returns success to its caller. This is wrong behaviour.
'tomoyo_write_domain' should return error from tomoyo_delete_domain() to its
caller.
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Pull core/locking changes for v3.4 from Ingo Molnar
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex: Simplify return logic
futex: Cover all PI opcodes with cmpxchg enabled check
Pull core/iommu changes for v3.4 from Ingo Molnar
* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/iommu/intel: Increase the number of iommus supported to MAX_IO_APICS
x86/iommu/intel: Fix identity mapping for sandy bridge
* branch 'dcache-word-accesses':
vfs: use 'unsigned long' accesses for dcache name comparison and hashing
This does the name hashing and lookup using word-sized accesses when
that is efficient, namely on x86 (although any little-endian machine
with good unaligned accesses would do).
It does very much depend on little-endian logic, but it's a very hot
couple of functions under some real loads, and this patch improves the
performance of __d_lookup_rcu() and link_path_walk() by up to about 30%.
Giving a 10% improvement on some very pathname-heavy benchmarks.
Because we do make unaligned accesses past the filename, the
optimization is disabled when CONFIG_DEBUG_PAGEALLOC is active, and we
effectively depend on the fact that on x86 we don't really ever have the
last page of usable RAM followed immediately by any IO memory (due to
ACPI tables, BIOS buffer areas etc).
Some of the bit operations we do are a bit "subtle". It's commented,
but you do need to really think about the code. Or just consider it
black magic.
Thanks to people on G+ for some of the optimized bit tricks.
For some odd historical reason, the final mixing round for the dentry
cache hash table lookup had an insane "xor with big constant" logic. In
two places.
The big constant that is being xor'ed is GOLDEN_RATIO_PRIME, which is a
fairly random-looking number that is designed to be *multiplied* with so
that the bits get spread out over a whole long-word.
But xor'ing with it is insane. It doesn't really even change the hash -
it really only shifts the hash around in the hash table. To make
matters worse, the insane big constant is different on 32-bit and 64-bit
builds, even though the name hash bits we use are always 32-bit (and the
bits from the pointer we mix in effectively are too).
It's all total voodoo programming, in other words.
Now, some testing and analysis of the hash chains shows that the rest of
the hash function seems to be fairly good. It does pick the right bits
of the parent dentry pointer, for example, and while it's generally a
bad idea to use an xor to mix down the upper bits (because if there is a
repeating pattern, the xor can cause "destructive interference"), it
seems to not have been a disaster.
For example, replacing the hash with the normal "hash_long()" code (that
uses the GOLDEN_RATIO_PRIME constant correctly, btw) actually just makes
the hash worse. The hand-picked hash knew which bits of the pointer had
the highest entropy, and hash_long() ends up mixing bits less optimally
at least in some trivial tests.
So the hash function overall seems fine, it just has that really odd
"shift result around by a constant xor".
So get rid of the silly xor, and replace the down-mixing of the bits
with an add instead of an xor that tends to not have the same kind of
destructive interference issues. Some stats on the resulting hash
chains shows that they look statistically identical before and after,
but the code is simpler and no longer makes you go "WTF?".
Also, the incoming hash really is just "unsigned int", not a long, and
there's no real point to worry about the high 26 bits of the dentry
pointer for the 64-bit case, because they are all going to be identical
anyway.
So also change the hashing to be done in the more natural 'unsigned int'
that is the real size of the actual hashed data anyway.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add timing data for Hitachi SP10Q010 display and allow configuration
of the 4bpp palette. For 4bpp framebuffer enable reversed order of
pixels in a byte. This requires defining FB_CFB_REV_PIXELS_IN_BYTE
and additionally setting var.nonstd to the value FB_NONSTD_REV_PIX_IN_B.
Note that it is not enough to set da8xx_fb_var.nonstd to this value
statically, since FBIOPUT_VSCREENINFO ioctl might pass var struct with
.nonstd field set to zero or another value. Therefore this setting must
be adjusted in fb_check_var() according to the requested bpp value.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Remove incorrect SEC_MINI_B settings-TODO complete this section.
Correct break and remove return -EINVAL within set tone. It appears
there is a bug that occasionally something other than ON/OFF is
sent stalling the driver. Just continue and write back registers.
Set register b2 in setup. This is the set voltage pin which
isn't used in lmedm04 driver but it is always set to 0x1.
Correct the if statements in set_tuner_rf.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some changes for previous patch I liked to do.
Just move tuner init and sleep to own functions from the demod
init and sleep functions. Functionality remains still almost the same.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
