As this functionality relies on getting a firmware notification
it is difficult to test. Allow accessing the data for it from
debugfs to be able to trigger all kinds of scenarios to test.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
A new host command can be used to configure the scheduler
instead of accessing the scheduler's registers from the
driver. This is easier and less error prone since accessing
the hardware at certain moments can lead to races with the
firmware.
Prefer to use the host command whenever it is available.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Use only basic dwell time (10 ms for active scan and 110 for passive),
regardless of the number of the probes and the band, if it is
supported by the FW. The FW will add 3 ms for each probe sent and 10
ms for low band channels.
Add a TLV flag to indicate such support in FW.
This fix is needed to fix few bugs regarding scans that take too much time.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The driver doesn't support the firmwares that don't have
these capabilities. The code that actually used these
flags has been removed already, but the flags were left
for an unclear reason. Remove them.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Print the nvm version in the log for debugging purposes.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fragmented scan should be applied for all channels, passive and active.
When scanning on passive channels the firmware uses frag_passive_dwell
to define the maximum continuous scan time before returning to the
operating channel. On active channels max_out_time is the parameter
used by the firmware to define the maximum time allowed out of the
operating channel. Since active channels' scan should also be fragmented
set max_out_time equal to frag_passive_dwell.
In addition:
- Set max_out_time and suspend_time if the firmware doesn't support
fragmented scan to avoid unexpected behavior.
- Adjust max_out_time for second level of scan precedence.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This is to work around interoperability bugs with devices
that don't hanle MIMO properly.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
iwl_mvm_fw_dbg_collect allows to collect debug data from
the firmware. Most of the firmware interaction is done in
non-sleepable context. It makes little sense to force the
caller of iwl_mvm_fw_dbg_collect to sleep.
Defer the actual collection to a worker so that this
function will be able to be called from any context.
Reviewed-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In case platform is in d0i3 - make sure it is awake when
writing the registers to stop the monitor when collecting FW
debug data. Plus, remove unneeded mutex locking currently
done.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This option enables scan offload iteration complete notification from
firmware which includes the last iteration's status and the scanned
channels from the current iteration.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add a new config for 4165 series over PCI and insert support
for two new 4165 series PCI IDs.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This makes sure that we're not trying to read/write any of
the FW debug data collected during d0i3.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Repeating the legacy rates avoids degrading quickly to
lower rates due to collisions which is common when doing
TCP Tx traffic in legacy.
This slightly improves TCP Tx throughput while working
in legacy in different scenarios.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If Tx failed because the STA was in powersave there's no point
in sending a BAR so avoid indicating AMPDU_NO_BACK to mac80211.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When using overlays with drivers calling of_populate the notifier
will try to create the device twice. Using the populated bit
before proceeding protects against this.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
During the course of the rewrites a bug sneaked in when dealing
with children nodes of overlays, which ends up duplicating
sub nodes.
Simply remove the duplicate traversal of child nodes to fix.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Since b2052564e6 ("mm: memcontrol: continue cache reclaim from
offlined groups"), re-mounting the memory controller after using it is
very likely to hang.
The cgroup core assumes that any remaining references after deleting a
cgroup are temporary in nature, and synchroneously waits for them, but
the above-mentioned commit has left-over page cache pin its css until
it is reclaimed naturally. That being said, swap entries and charged
kernel memory have been doing the same indefinite pinning forever, the
bug is just more likely to trigger with left-over page cache.
Reparenting kernel memory is highly impractical, which leaves changing
the cgroup assumptions to reflect this: once a controller has been
mounted and used, it has internal state that is independent from mount
and cgroup lifetime. It can be unmounted and remounted, but it can't
be reconfigured during subsequent mounts.
Don't offline the controller root as long as there are any children,
dead or alive. A remount will no longer wait for these old references
to drain, it will simply mount the persistent controller state again.
Reported-by: "Suzuki K. Poulose" <Suzuki.Poulose@arm.com>
Reported-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
The list is in the process of closing.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: linux-wireless@vger.kernel.org
Cc: "Michael Renzmann" <mrenzmann@madwifi-project.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
LPCR_PECE1 bit controls whether decrementer interrupts are allowed to
cause exit from power-saving mode. While waking up from winkle, restoring
LPCR with LPCR_PECE1 set (i.e Decrementer interrupts allowed) can cause
issue in the following scenario:
- All the threads in a core are offlined. The core enters deep winkle.
- Spurious interrupt wakes up a thread in the core. Here LPCR is restored
with LPCR_PECE1 bit set.
- Since it was a spurious interrupt on a offline thread, the thread clears
the interrupt and goes back to winkle.
- Here before the thread executes winkle and puts the core into deep winkle,
if a decrementer interrupt occurs on any of the sibling threads in the core
that thread wakes up.
- Since in offline loop we are flushing interrupt only in case of external
interrupt, the decrementer interrupt does not get flushed. So at this stage
the thread is stuck in this is loop of waking up at 0x100 due to decrementer
interrupt, not flushing the interrupt as only external interrupts get flushed,
entering winkle, waking up at 0x100 again.
Fix this by programming PORE to restore LPCR with LPCR_PECE1 bit
cleared when waking up from winkle.
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
* Instantiate GIC from C board code in legacy builds on r8a7778 and r8a7779
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Mb4f
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-fixes2-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Merge "Second Round of Renesas ARM Based SoC Fixes for v3.19" from Simon
Horman:
* Instantiate GIC from C board code in legacy builds on r8a7778 and r8a7779
* tag 'renesas-soc-fixes2-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7779: Instantiate GIC from C board code in legacy builds
ARM: shmobile: r8a7778: Instantiate GIC from C board code in legacy builds
Signed-off-by: Olof Johansson <olof@lixom.net>
James Bottomley points out that it will be -1 during unload. It's
only used for diagnostics, so let's not hide that as it could be a
clue as to what's gone wrong.
Cc: Jason Wessel <jason.wessel@windriver.com>
Acked-and-documention-added-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Masami Hiramatsu <maasami.hiramatsu.pt@hitachi.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
device_caps in struct v4l2_capability were inadequately set in
VIDIOC_QUERYCAP. Fix this. Without this a WARN_ON in the v4l2 core
is triggered. This WARN_ON was added for kernel 3.19 exactly to
detect these situations.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The VIDIOC_QUERYCAP function should set device_caps, but this was missing.
In addition, it set the version field as well, but that should be done by
the core, not by the driver.
If a driver doesn't set device_caps the v4l2 core will issue a WARN_ON, so
it's important that this is set correctly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The locking scheme inside the vb2 thread is unsafe when stopping the
thread. In particular kthread_stop was called *after* internal data
structures were cleaned up instead of doing that before. In addition,
internal vb2 functions were called after threadio->stop was set to
true and vb2_internal_streamoff was called. This is also not allowed.
All this led to a variety of race conditions and kernel warnings and/or
oopses.
Fixed by moving the kthread_stop call up before the cleanup takes
place, and by checking threadio->stop before calling internal vb2
queuing operations.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v3.16 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The V4L2 API requires both .capabilities and .device_caps fields of
struct v4l2_capability to be set. Otherwise the compliance checker
complains and since commit "v4l2-ioctl: WARN_ON if querycap didn't fill
device_caps" a compile-time warning is issued. Fix this non-compliance
in the rcar_vin driver.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The V4L2 API requires both .capabilities and .device_caps fields of
struct v4l2_capability to be set. Otherwise the compliance checker
complains and since commit "v4l2-ioctl: WARN_ON if querycap didn't fill
device_caps" a compile-time warning is issued. Fix this non-compliance
in several soc-camera camera host drivers.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 2adb177e57 removed 2 devices
from the cxusb device table but failed to fix up the T230 properties
that follow, meaning that this device no longer gets detected properly.
Adjust the cxusb_table index appropriate so detection works.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Unconditionally attaching Si2161/Si2165 demod driver
breaks Hauppauge WinTV Starburst.
So create own card entry for this.
Add card name comments to the subsystem ids.
This fixes a regression introduced in 3.17 by
36efec48e2 ([media] cx23885: Add si2165 support for HVR-5500)
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
CC: stable@vger.kernel.org # for 3.17 and upper
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
X-Patchwork-Delegate: m.chehab@samsung.com
Changeset ea2e813e8c moved the driver to staging, but it forgot to
preserve the existing dependency.
Fixes: ea2e813e8c ("[media] tlg2300: move to staging in preparation for removal")
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Put controller into init mode in network stop to end pending transmissions. The
issue is observed in cases when transmitted frame is not acked.
Signed-off-by: Viktor Babrian <babrian.viktor@renyi.mta.hu>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
because gcc 4.8 for superH does not support -m32, and the recordmcount.pl
script adds "-m32" when re-compiling the object files with the mcount
locations.
I was not able to reproduce this problem, as it seems that -m32 works fine
for my cross compiler gcc 4.6.3, but I have to assume that -m32 was
deprecated somewhere between 4.6 and 4.8. As it still seems to compile
fine without -m32, I have no reason not to add this patch, as having
-m32 seems to cause trouble for others.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUv9sOAAoJEEjnJuOKh9ldPUIIAJle6R3v+53gylalVhOnn56f
fQkONz1HvLteneBGTFG4xiwK6BJNeTOcLOQbCfBwNBZUjg7QG5eEU3wBG6DCZNIf
Tc1DqB78Fx9HnI0wJby/VtgIMbTqvPsXta0J75g7EFXwaP8bUZFL1s6QmskKlFTf
Gvhr93YP2SFawRf8Gy9AVCkLBSwU1T5y0IsQXPw49buNT+aWwoMWCNJb03rLfZYz
MCNgTfQxf4aYK1EThvb8xurjD2rZkJmRc/LN37vj8M+2e9HoIitCd4O/doxEQtvK
aFw7q/K23bFIXfjKoF1Yjk8hLoQZgCxruZwmZyxEEPtTGsUfNcSyfgpHTNeNDrk=
=d6qd
-----END PGP SIGNATURE-----
Merge tag 'trace-sh-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull superh tracing fix from Steven Rostedt:
"It's been reported that function tracing does not work on the sh
architecture because gcc 4.8 for superH does not support -m32, and the
recordmcount.pl script adds "-m32" when re-compiling the object files
with the mcount locations.
I was not able to reproduce this problem, as it seems that -m32 works
fine for my cross compiler gcc 4.6.3, but I have to assume that -m32
was deprecated somewhere between 4.6 and 4.8. As it still seems to
compile fine without -m32, I have no reason not to add this patch, as
having -m32 seems to cause trouble for others"
* tag 'trace-sh-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
scripts/recordmcount.pl: There is no -m32 gcc option on Super-H anymore
The current rounding of "size" is wrong:
- If "start" is sufficiently near the next page boundary, "size"
is decremented by more than enough and the last page is lost.
- If "size" is sufficiently small, it is wrapped around and gets
a bogus value.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Disable power down counter of the watchdog to avoid system resets. The
watchdog power down counter is set automatically by the chip. If it is
not set to 0 in the driver, the system resets.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Improve power management operations(suspend and resume) as part of
dev_pm_ops for IMX2 watchdog driver.
If PM will be supported, please make sure that the wdev->clk
could disable the watchdog's counter input clock source or can
mask watchdog's reset request to the core.
If watchdog is still used by consumers and resumes from deep
sleep state, we need to restart the watchdog again without
enabling the timer.
If watchdog been has started --> stopped by the consumers and
resumes from non-deep sleep state, then start the timer again.
If watchdog has been started --> stopped by the consumers and
resumes from deep sleep state, will do nothing. The watchdog
will be restarted by consumers next time to be used.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This batch contains two fixes for FireWire lib module and a quirk
for yet another Logitech WebCam. The former is the fixes for MIDI
handling I forgot to pick up during the merge window. All the
fixed code is pretty local and shouldn't give any regressions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=HKNt
-----END PGP SIGNATURE-----
Merge tag 'sound-3.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This batch contains two fixes for FireWire lib module and a quirk for
yet another Logitech WebCam. The former is the fixes for MIDI
handling I forgot to pick up during the merge window. All the fixed
code is pretty local and shouldn't give any regressions"
* tag 'sound-3.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Add mic volume fix quirk for Logitech Webcam C210
ALSA: firewire-lib: limit the MIDI data rate
ALSA: firewire-lib: remove rx_blocks_for_midi quirk
Pull drm fixes from Dave Airlie:
"Just back from LCA + some days off, had some fixes from the past 2 weeks,
Some amdkfd code removal for a feature that wasn't ready, otherwise
just one fix for core helper sleeping, exynos, i915, and radeon fixes.
I thought I had some sti fixes but they were already in, and it
confused me for a few mins this morning"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm: fb helper should avoid sleeping in panic context
drm/exynos: fix warning of vblank reference count
drm/exynos: remove unnecessary runtime pm operations
drm/exynos: fix reset codes for memory mapped hdmi phy
drm/radeon: use rv515_ring_start on r5xx
drm/radeon: add si dpm quirk list
drm/radeon: don't print error on -ERESTARTSYS
drm/i915: Fix mutex->owner inspection race under DEBUG_MUTEXES
drm/i915: Ban Haswell from using RCS flips
drm/i915: vlv: sanitize RPS interrupt mask during GPU idling
drm/i915: fix HW lockup due to missing RPS IRQ workaround on GEN6
drm/i915: gen9: fix RPS interrupt routing to CPU vs. GT
drm/exynos: remove the redundant machine checking code
drm/radeon: add a dpm quirk list
drm/amdkfd: Fix sparse warning (different address space)
drm/radeon: fix VM flush on CIK (v3)
drm/radeon: fix VM flush on SI (v3)
drm/radeon: fix VM flush on cayman/aruba (v3)
drm/amdkfd: Drop interrupt SW ring buffer
- Skip caching volatile registers in tps65218
- Use correct address base in tps65218
- Repair deadlock on suspend in rtsx_usb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Afdx
-----END PGP SIGNATURE-----
Merge tag 'mfd-fixes-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD fixes from Lee Jones:
- Avoid platform ID collision in da9052
- Skip caching volatile registers in tps65218
- Use correct address base in tps65218
- Repair deadlock on suspend in rtsx_usb
* tag 'mfd-fixes-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: rtsx_usb: Fix runtime PM deadlock
mfd: tps65218: Make INT1 our status_base register
mfd: tps65218: Make INT[12] and STATUS registers volatile
mfd: da9052-core: Fix platform-device id collision
Commit 6b5fe46dfa (btrfs: do commit in sync_fs if there are pending
changes) will call btrfs_start_transaction() in sync_fs(), to handle
some operations needed to be done in next transaction.
However this can cause deadlock if the filesystem is frozen, with the
following sys_r+w output:
[ 143.255932] Call Trace:
[ 143.255936] [<ffffffff816c0e09>] schedule+0x29/0x70
[ 143.255939] [<ffffffff811cb7f3>] __sb_start_write+0xb3/0x100
[ 143.255971] [<ffffffffa040ec06>] start_transaction+0x2e6/0x5a0
[btrfs]
[ 143.255992] [<ffffffffa040f1eb>] btrfs_start_transaction+0x1b/0x20
[btrfs]
[ 143.256003] [<ffffffffa03dc0ba>] btrfs_sync_fs+0xca/0xd0 [btrfs]
[ 143.256007] [<ffffffff811f7be0>] sync_fs_one_sb+0x20/0x30
[ 143.256011] [<ffffffff811cbd01>] iterate_supers+0xe1/0xf0
[ 143.256014] [<ffffffff811f7d75>] sys_sync+0x55/0x90
[ 143.256017] [<ffffffff816c49d2>] system_call_fastpath+0x12/0x17
[ 143.256111] Call Trace:
[ 143.256114] [<ffffffff816c0e09>] schedule+0x29/0x70
[ 143.256119] [<ffffffff816c3405>] rwsem_down_write_failed+0x1c5/0x2d0
[ 143.256123] [<ffffffff8133f013>] call_rwsem_down_write_failed+0x13/0x20
[ 143.256131] [<ffffffff811caae8>] thaw_super+0x28/0xc0
[ 143.256135] [<ffffffff811db3e5>] do_vfs_ioctl+0x3f5/0x540
[ 143.256187] [<ffffffff811db5c1>] SyS_ioctl+0x91/0xb0
[ 143.256213] [<ffffffff816c49d2>] system_call_fastpath+0x12/0x17
The reason is like the following:
(Holding s_umount)
VFS sync_fs staff:
|- btrfs_sync_fs()
|- btrfs_start_transaction()
|- sb_start_intwrite()
(Waiting thaw_fs to unfreeze)
VFS thaw_fs staff:
thaw_fs()
(Waiting sync_fs to release
s_umount)
So deadlock happens.
This can be easily triggered by fstest/generic/068 with inode_cache
mount option.
The fix is to check if the fs is frozen, if the fs is frozen, just
return and waiting for the next transaction.
Cc: David Sterba <dsterba@suse.cz>
Reported-by: Gui Hecheng <guihc.fnst@cn.fujitsu.com>
Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
[enhanced comment, changed to SB_FREEZE_WRITE]
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <clm@fb.com>
Fs_info->pending_changes is never cleared since the original code uses
cmpxchg(&fs_info->pending_changes, 0, 0), which will only clear it if
pending_changes is already 0.
This will cause a lot of problem when mount it with inode_cache mount
option.
If the btrfs is mounted as inode_cache, pending_changes will always be
1, even when the fs is frozen.
Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.cz>
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <clm@fb.com>
- Remove the interrupt SW ring buffer impl. as it is not used by any module
in amdkfd.
- Fix a sparse warning
* tag 'drm-amdkfd-fixes-2015-01-13' of git://people.freedesktop.org/~gabbayo/linux:
drm/amdkfd: Fix sparse warning (different address space)
drm/amdkfd: Drop interrupt SW ring buffer
misc i915 fixes
* tag 'drm-intel-fixes-2015-01-15' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Fix mutex->owner inspection race under DEBUG_MUTEXES
drm/i915: Ban Haswell from using RCS flips
drm/i915: vlv: sanitize RPS interrupt mask during GPU idling
drm/i915: fix HW lockup due to missing RPS IRQ workaround on GEN6
drm/i915: gen9: fix RPS interrupt routing to CPU vs. GT
