On gen4 and earlier the GPU reset also resets the display, so we should
protect against concurrent modeset operations. Grab all the modeset locks
around the entire GPU reset dance, remebering first ti dislogde any
pending page flip to make sure we don't deadlock. Any pageflip coming
in between these two steps should fail anyway due to reset_in_progress,
so this should be safe.
This fixes a lot of failed asserts in the modeset code when there's a
modeset racing with the reset. Naturally the asserts aren't happy when
the expected state has disappeared.
v2: Drop UMS checks, complete pending flips after the reset (Daniel)
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
g33 seems to sit somewhere between the 915/945/965 style and the
g4x style. The bits look like g4x, but we still need to do a full
reset including display.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
915/945 have the same reset registers as 965, so share the code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On pre-ctg GPU reset also resets the display hardware. Force a mode
restore after the GPU reset, and also re-init clock gating.
v2: Use intel_modeset_init_hw() instead of intel_init_clock_gating()
in case more relevant stuff gets added there at some point
Restore interrupts after the reset as well
Tested-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On pre-ctg the reset bit directly controls the reset signal. We must
assert it for >=20usec and then deassert it. Bit 1 is a RO status bit
which should also go down when the reset is no longer asserted.
Tested-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's quite a few bug reports with error states where the error
reasons makes just about no sense at all. Like dying on tlbs for a
display plane that's not even there. Also users don't really report a
lot of bad side effects generally, just the error states.
Furthermore we don't even enable these interrupts any more on gen5+
(though the handling code is still there). So this mostly concerns old
platforms.
Given all that lets make our lives a bit easier and stop capturing
error states, in the hopes that we can just ignore them. In case
that's not true and the gpu indeed dies the hangcheck should
eventually kick in. And I've left some debug log in to make this case
noticeble. Referenced bug is just an example.
v2: Fix missing \n Jani spotted.
References: https://bugs.freedesktop.org/show_bug.cgi?id=82095
References: https://bugs.freedesktop.org/show_bug.cgi?id=85944
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The problem here is that SNA pins batchbuffers to etch out a bit more
performance. Iirc it started out as a w/a for i830M (which we've
implemented in the kernel since a long time already). The problem is
that the pin ioctl wasn't added in
commit d23db88c3a
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri May 23 08:48:08 2014 +0200
drm/i915: Prevent negative relocation deltas from wrapping
Fix this by simply disallowing pinning from userspace so that the
kernel is in full control of batch placement again. Especially since
distros are moving towards running X as non-root, so most users won't
even be able to see any benefits.
UMS support is dead now, but we need this minimal patch for
backporting. Follow-up patch will remove the pin ioctl code
completely.
Note to backporters: You must have both
commit b45305fce5
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Dec 17 16:21:27 2012 +0100
drm/i915: Implement workaround for broken CS tlb on i830/845
which laned in 3.8 and
commit c4d69da167
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Sep 8 14:25:41 2014 +0100
drm/i915: Evict CS TLBs between batches
which is also marked cc: stable. Otherwise this could introduce a
regression by disabling the userspace w/a without the kernel w/a being
fully functional on i830/45.
References: https://bugs.freedesktop.org/show_bug.cgi?id=76554#c116
Cc: stable@vger.kernel.org # requires c4d69da167 and v3.8
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
In all likelihood we will do a few hundred errnoneous register
operations if we do a single invalid register access whilst the device
is suspended. As each instance causes a WARN, this floods the system
logs and can make the system unresponsive.
The warning was first introduced in
commit b2ec142cb0
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Fri Feb 21 13:52:25 2014 -0300
drm/i915: call assert_device_not_suspended at gen6_force_wake_work
and despite the claims the WARN is still encountered in the wild today.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV infoframes were not being enabled.
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When doing a nop modeset we currently leave crtc->new_config point at
the already freed temporary pipe_config. That will anger the sanity
checks in intel_modeset_update_state() when the nop modeset gets
followed by a GPU reset on gen3/4 where the display block gets fully
reinitialized during the reset.
So leave crtc->new_config alone until we know a modeset is actually
required.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These BUGs can be erroneously triggered by frags which refer to
tail pages within a compound page. The data in these pages may
overrun the hardware page while still being contained within the
compound page, but since compound_order() evaluates to 0 for tail
pages the assertion fails. The code already iterates through
subsequent pages correctly in this scenario, so the BUGs are
unnecessary and can be removed.
Fixes: f36c374782 ("xen/netfront: handle compound page fragments on transmit")
Cc: <stable@vger.kernel.org> # 3.7+
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some android devices, there will be a "divide by zero" exception.
vmpr->scanned could be zero before spin_lock(&vmpr->sr_lock).
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=88051
[akpm@linux-foundation.org: neaten]
Reported-by: ji_ang <ji_ang@163.com>
Cc: Anton Vorontsov <anton.vorontsov@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a frontswap dup-store failed, it should invalidate the expired page
in the backend, or it could trigger some data corruption issue.
Such as:
1. use zswap as the frontswap backend with writeback feature
2. store a swap page(version_1) to entry A, success
3. dup-store a newer page(version_2) to the same entry A, fail
4. use __swap_writepage() write version_2 page to swapfile, success
5. zswap do shrink, writeback version_1 page to swapfile
6. version_2 page is overwrited by version_1, data corrupt.
This patch fixes this issue by invalidating expired data immediately
when meet a dup-store failure.
Signed-off-by: Weijie Yang <weijie.yang@samsung.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Seth Jennings <sjennings@variantweb.net>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Bob Liu <bob.liu@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minor fixlet to perform the reserved pages counter aggregation for each
node, at show_mem()
Signed-off-by: Rafael Aquini <aquini@redhat.com>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Johannes Weiner <jweiner@redhat.com>
Acked-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A few more small fixes for 3.18.
* 'drm-fixes-3.18' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: kernel panic in drm_calc_vbltimestamp_from_scanoutpos with 3.18.0-rc6
drm/radeon: Ignore RADEON_GEM_GTT_WC on 32-bit x86
drm/radeon: sync all BOs involved in a CS v2
The DRM connector's encoder pointer is managed internally by the DRM
core and set to NULL when the DRM connector is disconnected from the
CRTC it was attached to. This results in a NULL pointer dereference in
the HDMI connector functions when trying to call the associated slave
encoder's operations.
Fix this by retrieving the slave encoder pointer from the R-Car
connector structure instead of the DRM connector structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm-intel-next-2014-11-21:
- infoframe tracking (for fastboot) from Jesse
- start of the dri1/ums support removal
- vlv forcewake timeout fixes (Imre)
- bunch of patches to polish the rps code (Imre) and improve it on bdw (Tom
O'Rourke)
- on-demand pinning for execlist contexts
- vlv/chv backlight improvements (Ville)
- gen8+ render ctx w/a work from various people
- skl edp programming (Satheeshakrishna et al.)
- psr docbook (Rodrigo)
- piles of little fixes and improvements all over, as usual
* tag 'drm-intel-next-2014-11-21-fixed' of git://anongit.freedesktop.org/drm-intel: (117 commits)
drm/i915: Don't pin LRC in GGTT when dumping in debugfs
drm/i915: Update DRIVER_DATE to 20141121
drm/i915/g4x: fix g4x infoframe readout
drm/i915: Only call mod_timer() if not already pending
drm/i915: Don't rely upon encoder->type for infoframe hw state readout
drm/i915: remove the IRQs enabled WARN from intel_disable_gt_powersave
drm/i915: Use ggtt error obj capture helper for gen8 semaphores
drm/i915: vlv: increase timeout when setting idle GPU freq
drm/i915: vlv: fix cdclk setting during modeset while suspended
drm/i915: Dump hdmi pipe_config state
drm/i915: Gen9 shadowed registers
drm/i915/skl: Gen9 multi-engine forcewake
drm/i915: Read power well status before other registers for drpc info
drm/i915: Pin tiled objects for L-shaped configs
drm/i915: Update ring freq for full gpu freq range
drm/i915: change initial rps frequency for gen8
drm/i915: Keep min freq above floor on HSW/BDW
drm/i915: Use efficient frequency for HSW/BDW
drm/i915: Can i915_gem_init_ioctl
drm/i915: Sanitize ->lastclose
...
Not just the userspace relocs, otherwise we won't wait
for a swapped out page tables to be swapped in again.
v2: rebased on Alex current drm-fixes-3.18
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
irq_of_parse_and_map() returns 0 on error (the result is unsigned int),
so testing for negative result never works.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
bio integrity handling is broken on a system with LVM layered atop a
DIF/DIX SCSI drive because device mapper clones the bio, modifies the
clone, and sends the clone to the lower layers for processing.
However, the clone bio has bi_vcnt == 0, which means that when the sd
driver calls bio_integrity_process to attach DIX data, the
for_each_segment_all() call (which uses bi_vcnt) returns immediately
and random garbage is sent to the disk on a disk write. The disk of
course returns an error.
Therefore, teach bio_integrity_process() to use bio_for_each_segment()
to iterate the bio_vecs, since the per-bio iterator tracks which
bio_vecs are associated with that particular bio. The integrity
handling code is effectively part of the "driver" (it's not the bio
owner), so it must use the correct iterator function.
v2: Fix a compiler warning about abandoned local variables. This
patch supersedes "block: bio_integrity_process uses wrong bio_vec
iterator". Patch applies against 3.18-rc6.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
LRC object does not need to be mapped into the GGTT when dumping. A side-effect
of this patch is that a compiler warning goes away (not checking return value
of i915_gem_obj_ggtt_pin).
v2: Broke out individual context dumping into a new function as the indentation
was getting a bit crazy. Added notification of contexts with no gem object for
debugging purposes. Removed unnecessary pin_pages and unpin_pages, replaced
with explicit get_pages for the context object as there may be no backing store
allocated at this time (Comment for get_pages says "Ensure that the associated
pages are gathered from the backing storage and pinned into our object").
Improved error checking - get_pages and get_page are checked for failure.
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
[danvet: Align paramter continuation lines properly. Also add some
braces to the nested loops again for readability.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise we'll have backtraces in assert_panel_unlocked because the
BIOS locks the register. In the reporter's case this regression was
introduced in
commit c31407a367
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Thu Oct 18 21:07:01 2012 +0100
drm/i915: Add no-lvds quirk for Supermicro X7SPA-H
Reported-by: Alexey Orishko <alexey.orishko@gmail.com>
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Cc: stable@vger.kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Francois Tigeot <ftigeot@wolfpond.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Tested-by: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This patch adds the basic structure of a DRM Driver for Rockchip Socs.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Apparently PCH fifo underruns are tricky, we have plenty reports that
we see the occasional underrun (especially at boot-up).
So for a change let's see what happens when we don't re-enable pch
fifo underrun reporting when the pipe is disabled. This means that the
kernel can't catch pch fifo underruns when they happen (except when
all pipes are on on the pch). But we'll still catch underruns when
disabling the pipe again. So not a terrible reduction in test
coverage.
Since the DRM_ERROR is new and hence a regression plan B would be to
revert it back to a debug output. Which would be a lot worse than this
hack for underrun test coverage in the wild. See the referenced
discussions for more.
References: http://mid.gmane.org/CA+gsUGRfGe3t4NcjdeA=qXysrhLY3r4CEu7z4bjTwxi1uOfy+g@mail.gmail.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85898
References: https://bugs.freedesktop.org/show_bug.cgi?id=85898
References: https://bugs.freedesktop.org/show_bug.cgi?id=86233
References: https://bugs.freedesktop.org/show_bug.cgi?id=86478
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Tested-by: lu hua <huax.lu@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Dell has new machines. It supports headset Mic and Headphone Mic.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Tegra K1 voltage support, and coherency improvements
- GM204 support (modesetting, still waiting on NVIDIA for signed fw to
proceed further), and a lot of bios/i2c/devinit adjustments needed to
support it
- GT21x memory reclocking work
- Various other bits and pieces, most of which are prep-work for a
couple of bigger projects I didn't get finished in time
* 'linux-3.19' of git://anongit.freedesktop.org/git/nouveau/linux-2.6: (73 commits)
drm/nv50/kms: drop requirement that framebuffer bos be contig up-front
drm/nv50/kms: directly use cursor image from userspace buffer
drm/nouveau/kms: when pinning display-related buffers, force contig vram
drm/nouveau: teach nouveau_bo_pin() how to force a contig vram allocation
drm/nouveau/volt: add support for GK20A
drm/nouveau/platform: add GPU speedo information to nouveau platform
drm/nouveau/volt: allow non-bios voltage scaling
drm/gf100-/gr: return non-fatal error code when fw not present
drm/nouveau/devinit: bump priv ring timeouts before executing scripts
drm/nouveau/bios: translate ramcfg strap through M0203
drm/nouveau/fb: make use of M0203 routines for ram type determination
drm/nouveau/bios: add parsing of BIT M(v2) +0x03 table
drm/nouveau/core: allow vbios parsing without knowing chipset type
drm/nouveau/lib: add null backend
drm/nouveau/device: store revision
drm/nouveau/core: add some forgotten subdevs to disable mask
drm/gk20a/clk: fix max VCO value
drm/nouveau: we need pin_refcnt for nouveau_bo_placement_set()
drm/nv50-/kms: add some evo tracing ability for debugging
drm/nv50/kms: use sclass() instead of trial-and-error
...
Preparation for transition to planes, which use framebuffers for the
cursor image. We've always done copies from the userspace buffer up
until now for legacy reasons, there's no good reason to do so on the
chipsets this code covers.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We have the ability to move buffers around in the kernel if necessary,
and should probably use it rather than failing if userspace passes us
a non-contig buffer for a plane.
The NOUVEAU_GEM_TILE_NONCONTIG flag from userspace will become a mere
initial placement hint once all the relevant paths have been updated.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The voltage value are calculated by the hardware characterized
result.
Signed-off-by: Vince Hsu <vinceh@nvidia.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
For GK20A we need the GPU speedo value to calculate voltage levels.
Signed-off-by: Vince Hsu <vinceh@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Move the vbios parsing out of init() and call it conditionally if the
platform has a vbios. Non-vbios platforms can use the ctor() to init the
data structures.
Signed-off-by: Vince Hsu <vinceh@nvidia.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
A machine has been spotted where the ramcfg strap is "8", and the ramcfg
xlat table goes 0-7,0-7, resulting in us selecting config 0 for memory
items. On this particular system, config "8" is available and supposed
to be used. It appears that starting from GT21x (where Mv2 appears),
we're supposed to use the value in this table instead.
One concern here is that not all the places we currently use ramcfg xlat
are supposed to be treated the same now. The strap xlat table wasn't
removed from the vbios either, presumably for some kind of good reason.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We only support one kind of matching here (ramcfg strap), but it appears
alternate methods are possible. I wrote a tool to scan our vbios repo
for other types, but did not see any used. Hopefully this means there
aren't any in the wild that will now break.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
