This patch makes the EMAC driver use the new DCR access methods. It
doesn't yet uses dcr_map() and thus still only work with real DCRs.
This will be fixed in a later patch
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following patch fixes the failure of sunhme drivers on x86 hosts
due to missing pci_enable_device() and pci_set_master() calls, lost
during code refactoring. It has been filed as bugzilla bug #7502 [0]
and Debian bug #397460 [1].
[0] http://bugzilla.kernel.org/show_bug.cgi?id=7502
[1] http://bugs.debian.org/397460
Signed-off-by: Jurij Smakov <jurij@wooyd.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's bitrotten, long unmaintained, long hidden under BROKEN_ON_SMP,
etc. As scheduled in feature-removal-schedule.txt, and ack'd several
times on lkml.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Two thirds of packets are lost because of misalignment. Users of
Asus laptop did apparently not notice it.
Reported on Gigabyte GA-945GM-S2.
Fix for http://bugzilla.kernel.org/show_bug.cgi?id=7517
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
The 8110SB based n2100 board signals a lot of what ought to be
PCI data parity errors durint operation of the 8169 as target.
Experiment proved that the driver can ignore the error and
process the packet as if nothing had happened.
Let's add an ad-hoc knob to enable users to fix their system while
avoiding the risks of a wholesale change.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Mostly taken from Realtek's driver.
It's a bit yucky but the original is even worse.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
With async scanning, we're now tripping the BUG_ON in
sas_ex_discover_end_dev(), so make the error handling here correct.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Misc Fixes:
- Prevent references to NULL node list element in reset routines.
- Add missing IOCB types to switch tables
- Reset the card on Port Error 5
- Fix infinite loop in LUN reset
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The driver now allows both wwpn and wwnn to be set.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
To avoid continually updating the driver for new subsystem ids
(as adapter modules are proliferating), remove this 2nd level decode.
Genericize the reported Adapter names to be consistent across
Emulex product line.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add MSI (Message Signalled Interrupts) support
Actual use must be enabled via the new module parameter "lpfc_use_msi"
Defaults to no use
Many thanks to Frederic Temporelli who implemented the initial patch.
Signed-off-by: Frederic Temporelli <frederic.temporelli@ext.bull.net>
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adjust LOG_FCP logging to be more meaningful.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It was not accounted for in the fast/slow rings.
Genericize the implementation and control it via sysfs
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Discovery Fixes:
- Prevent starting discovery of a node if discovery is in progress.
- Code improvement (reduction) for lpfc_findnode_did().
- Update discovery to send RFF to Fabric on link up
- Bypass unique WWN checks for fabric addresses
- Add ndlp to plogi list prior to issuing the plogi els command
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is IBM Virtual SCSI target driver for tgt. The driver is based on
the original ibmvscsis driver:
http://lkml.org/lkml/2005/10/17/99
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
libsrp provides helper functions for SRP target drivers.
Some SRP target drivers would be out of drivers/scsi/ so we added an
entry for libsrp in drivers/scsi/Kconfig.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In the switch over, I forgot to set the command length, so it sends out
a request sense with whatever length the prior command had (and fails
badly if it wasn't 6).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use NULL instead of 0 for pointers (sparse warning):
drivers/scsi/qla2xxx/qla_attr.c:393:4: warning: Using plain integer as NULL pointer
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds code to fix up the PHYMODE4 "align timing"
register value on second-generation Promise SATA chips.
Failure to correct this value on non-x86 machines makes
drive detection prone to failure due to timeouts. (I've
observed about 50% detection failure rates on SPARC64.)
The HW boots with a bad value in this register, but on x86
machines the Promise BIOS corrects it to the value recommended
by the manual, so most people have been unaffected by this issue.
After developing the patch I checked Promise's SATAII driver,
and discovered that it also corrects PHYMODE4 just like this
patch does.
This patch depends on the sata_promise SATAII updates
patch I sent recently.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata switched to IRQ-driven IDENTIFY when IRQ-driven PIO was
introduced. This has caused a lot of problems including device
misdetection and phantom device.
ATA_FLAG_DETECT_POLLING was added recently to selectively use polling
IDENTIFY on problemetic drivers but many controllers and devices are
affected by this problem and trying to adding ATA_FLAG_DETECT_POLLING
for each such case is diffcult and not very rewarding.
This patch makes libata always use polling IDENTIFY. This is
consistent with libata's original behavior and drivers/ide's behavior.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ahci_init_controller() calls ahci_deinit_port() to make sure the
controller is stopped before initializing the controller. In turn,
ahci_deinit_port() invokes ahci_power_down() to power down the port.
If the controller supports slumber mode, the link is put into it.
Unfortunately, some devices don't implement link powersaving mode
properly and show erratic behavior after link is put into slumber
mode. For example, HL-DT-ST DVD-RAM GSA-H30N completely locks up on
slumber transition and can only be recovered with the *REAL* hard
reset - power removal and reapply.
Note that this makes the first probing reset different from all
others. If the above dvd-ram is hotplugged after ahci is initialized,
no problem occurs because ahci is already fully initialized with phy
powered up. So, this might also be the reason for other weird AHCI
initial probing abnormalities.
This patch moves power up/down out of port init/deinit and call them
only when needed.
Power down is now called only when suspending. As system suspend
usually involves powering down 12v for storage devices, this shouldn't
cause problem even if the attached device doesn't support slumber
mode. However, in partial power management and suspend failure cases,
devices might lock up after suspend attempt. I thought about removing
transition to slumber mode altogether but ahci spec mandates it before
HBA D3 state transition. Blacklisting such devices might be the
solution.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Separate out rw ATA taskfile building from ata_scsi_rw_xlat() into
ata_build_rw_tf(). This will be used to improve media error handling.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Sg'ify ata_exec_internal() and call it ata_exec_internal_sg().
Wrapper function around ata_exec_internal_sg() is implemented to
provide ata_exec_internal() interface.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Now that BMDMA status is recorded in irq handler. ata_bmdma_freeze()
is free to manipulate host status. Under certain circumstances, some
controllers (ICH7 in enhanced mode w/ IRQ shared) raise IRQ when CTL
register is written to and ATA_NIEN doesn't mask it.
This patch makes ata_bmdma_freeze() clear all pending IRQs after
freezing a port. This change makes explicit clearing in
ata_device_add() unnecessary and thus kills it. The removed code was
SFF-specific and was in the wrong place.
Note that ->freeze() handler is always called under ap->lock held and
irq disabled. Even if CTL manipulation causes stuck IRQ, it's cleared
immediately. This should be safe (enough) even in SMP environment.
More correct solution is to mask the IRQ from IRQ controller but that
would be an overkill.
Signed-off-by: Tejun Heo <htejun@gmail.com>
For certain errors, interrupt handler alter BMDMA host status before
entering EH (clears active and intr). Thus altered BMDMA host status
value is recorded by BMDMA EH and reported to user. Move BMDMA host
status recording from EH to interrupt handler.
Signed-off-by: Tejun Heo <htejun@gmail.com>
ata_scsi_dev_rescan() doesn't synchronize against SCSI device detach
and the target sdev might go away in the middle. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
If EH command is issued to a frozen port, it fails with AC_ERR_SYSTEM.
libata used to request sense even when the port is frozen needlessly
adding AC_ERR_SYSTEM to err_mask. Don't do it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
* READ CAPACITY (16) implementation fixed. Result was shifted by two
bytes. Carlos Pardo spotted this problem and submitted preliminary
patch. Capacity => 2TB is handled correctly now. (verifid w/ fake
capacity)
* Use dev->n_sectors instead of re-reading directly from ID data.
* Define and use ATA_SCSI_RBUF_SET() which considers rbuf length.
This should be done for all simulation functions. Userland can
issue any simulated command with arbitrary buffer length.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Carlos Pardo <Carlos.Pardo@siliconimage.com>
This patch implements ATA_FLAG_SETXFER_POLLING and use in pata_via.
If this flag is set, transfer mode setting performed by polling not by
interrupt. This should help those controllers which raise interrupt
before the command is actually complete on SETXFER.
Rationale for this approach.
* uses existing facility and relatively simple
* no busy sleep in the interrupt handler
* updating drivers is easy
While at it, kill now unused flag ATA_FLAG_SRST in pata_via.
Signed-off-by: Tejun Heo <htejun@gmail.com>
There are machines out there which share legacy PCI IDE IRQs w/ other
devices. libata SFF interrupt/HSM code is ready for shared IRQ and
has been setting IRQF_SHARED for devices in native PCI mode. Device
in legacy mode is still a PCI device and thus supposedly uses
active-low level triggered IRQ.
Machines with such setup should be quite rare and w/o this flag libata
is likely to fail loading and render the system unuseable. Also, IDE
driver has been setting IRQF_SHARED for devices in legacy mode for a
looooong time.
Signed-off-by: Tejun Heo <htejun@gmail.com>
sht->max_sectors is overrided unconditionally in ->slave_configure.
There's no reason to set it to any value.
Signed-off-by: Tejun Heo <htejun@gmail.com>
... into anonymous union of __wsum and __u32 (csum and csum_offset resp.)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PCI ID and detection for 5709 copper and SerDes chips.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
