Prevent OMAP UARTs from going idle while they are still transferring
data in PIO mode. This works around an oversight in the OMAP UART
hardware present in OMAP34xx and earlier: an idle UART won't send a
wakeup when the TX FIFO threshold is reached. This causes long delays
during data transmission when the MPU powerdomain enters a low-power
mode. The MPU interrupt controller is not able to respond to
interrupts when it's in a low-power state, so the TX buffer is not
refilled until another wakeup event occurs.
This fix changes the erratum i291 DMA idle workaround. Rather than
toggling between force-idle and no-idle, it will toggle between
smart-idle and no-idle. The important part of the workaround is the
no-idle part, so this shouldn't result in any change in behavior.
This fix should work on all OMAP UARTs. Future patches intended for
the 3.4 merge window will make this workaround conditional on a
"feature" flag, and will use the OMAP36xx+ TX event wakeup support.
Thanks to Kevin Hilman <khilman@ti.com> for mentioning the erratum i291
workaround, which led to the development of this approach.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xeae8):
Section mismatch in reference from the function cm_t35_init_usbh()
to the (unknown reference) .init.data:(unknown)
The function cm_t35_init_usbh() references
the (unknown reference) __initdata (unknown).
This is often because cm_t35_init_usbh lacks a __initdata
annotation or the annotation of (unknown) is wrong.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the latest Sourcery G++ Lite 2011.03-41 and latest linaro
tool-chains OMAP2 only build breaks with below error.
arch/arm/mach-omap2/omap-smc.S: Assembler messages:
arch/arm/mach-omap2/omap-smc.S:30: Error: selected processor does not support ARM mode `smc #0'
arch/arm/mach-omap2/omap-smc.S:53: Error: selected processor does not support ARM mode `smc #0'
arch/arm/mach-omap2/omap-smc.S:61: Error: selected processor does not support ARM mode `smc #0'
arch/arm/mach-omap2/omap-smc.S:69: Error: selected processor does not support ARM mode `smc #0'
arch/arm/mach-omap2/omap-smc.S:77: Error: selected processor does not support ARM mode `smc #0'
make[1]: *** [arch/arm/mach-omap2/omap-smc.o] Error 1
OMAP2 devices doesn't have the security support but the security support
was getting built because of OMAP2PLUS. Don't build security code for
OMAP2 devices.
While at it, fix the secure-common line in the Makefile to use tabs
instead of spaces.
Reported-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It includes:
- a compile fix for fsl-diu-fb
- a fix for a suspend/resume issue in atmel_lcdfb
- a fix for a suspend/resume issue in OMAP
- a workaround for a hardware bug to avoid physical damage in OMAP
- a really trivial dead code removal in intelfb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=2uP4
-----END PGP SIGNATURE-----
Merge tag 'fbdev-fixes-for-3.3-1' of git://github.com/schandinat/linux-2.6
fbdev fixes for 3.3
It includes:
- compile fix for fsl-diu-fb
- fix for a suspend/resume issue in atmel_lcdfb
- fix for a suspend/resume issue in OMAP
- workaround for a hardware bug to avoid physical damage in OMAP
- really trivial dead code removal in intelfb
* tag 'fbdev-fixes-for-3.3-1' of git://github.com/schandinat/linux-2.6:
atmel_lcdfb: fix usage of CONTRAST_CTR in suspend/resume
intelfb: remove some dead code
drivers/video: compile fixes for fsl-diu-fb.c
OMAPDSS: HDMI: PHY burnout fix
OMAP: 4430SDP/Panda: add HDMI HPD gpio
OMAP: 4430SDP/Panda: setup HDMI GPIO muxes
OMAPDSS: remove wrong HDMI HPD muxing
OMAP: 4430SDP/Panda: rename HPD GPIO to CT_CP_HPD
OMAP: 4430SDP/Panda: use gpio_free_array to free HDMI gpios
OMAPDSS: use sync versions of pm_runtime_put
.. several days delayed. No reason, I just didn't think of it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPKF4KAAoJEHm+PkMAQRiGw/YH+wXg2DpZUuHeBK52zMGlJBPc
DzX11/Uan3Y07gM0JbDzuVxwjX4vdxR2bV6r1qsLP8JEUnE8jyFC32DBGi5WAht7
F4KU/Uov2Ds5/wzvY4Iuo01C+JftQHXuy/Sbhck1d0LI0yjLejRaw+zuJv0x2/eS
7YqV+KTGE1lDuJs/Gyq1Vqr1g9831AuS1tv/g3gaqBuN6TcPBFCocaVxzwrUc+y6
94h26XbbOhQRIz38oqUkiqAGnvYS61ocyBcEiRHf0dXkNSDIINqlgukvd7YTXouA
jj/w/DWpMRcQuYAgqkrurr9+yWC9hVQcsvvQ5sAQnIPcxoR868sg1pO8Oheq+1g=
=kUzV
-----END PGP SIGNATURE-----
Merge tag 'v3.3-rc2' into depends/rmk/for-armsoc
There were conflicts between fixes going in after 3.3-rc1 and
Russell's stable arm-soc base branch. Resolving it in the dependency
branch so that each topic branch shares the same resolution.
Conflicts:
arch/arm/mach-at91/at91cap9.c
arch/arm/mach-at91/at91sam9g45.c
Call runtime pm APIs pm_runtime_get_sync() and pm_runtime_put()
for enabling/disabling clocks appropriately. Remove syscore_ops and
instead use SET_RUNTIME_PM_OPS macro.
There is no more need to call omap_device_disable_idle_on_suspend
since driver is PM runtime adapted now.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The only bank->type (method) used in the OMAP GPIO driver is MPUIO type as they
need to be handled separately. Identify the same using a flag and remove all
METHOD_* macros.
mpuio_init() function is defined under #ifdefs. It is required only in case
of MPUIO bank type and only when PM operations are supported by it.
This is applicable only in case of OMAP16xx SoC's MPUIO GPIO bank type.
For all the other cases it is a dummy function. Hence clean up the same
and remove all the OMAP SoC specific #ifdefs.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
It is not required to use hard-coded offsets any more in context save and
restore functions and instead use the generic offsets which have been correctly
initialized during device registration.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
By adding level and edge detection register offsets and then initializing them
correctly according to OMAP versions during device registrations we can now remove
lot of revision checks in these functions.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Wakeup enable register offset initialized according to OMAP versions
during device registration. Use this to avoid version checks.
Starting with OMAP4, legacy registers should not be used in combination
with the updated regsiters. Use wkup_en register consistently for
all SoCs wherever applicable.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove cpu-is checks while enabling/disabling OMAP GPIO module during a gpio
request/free.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Non-wakeup GPIOs are available only in OMAP2. Avoid cpu_is checks by making
non_wakeup_gpios as part of pdata.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Modify omap_gpio_prepare_for_idle() & omap_gpio_resume_after_idle() functions
to handle save context & restore context respectively in the OMAP GPIO driver
itself instead of calling these functions from pm specific files.
For this, in gpio_prepare_for_idle(), call *_get_context_loss_count() and in
gpio_resume_after_idle() call it again. If the count is different, do restore
context.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In omap3, save/restore context is implemented for GPIO banks 2-6 as GPIO bank1
is in wakeup domain. Instead of identifying bank's power domain by bank id,
use 'loses_context' flag which is filled by pwrdm_can_ever_lose_context()
during dev_init.
For getting the powerdomain pointer, omap_hwmod_get_pwrdm() is used.
omap_device_get_pwrdm() could not be used as the pwrdm information needs to be
filled in pdata, whereas omap_device_get_pwrdm() could be used only after
omap_device_build() call.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The gpio_bank_count is the count of number of GPIO devices in a SoC. Remove this
dependency from the driver by using list. Also remove the dependency on array of
pointers to gpio_bank struct of all GPIO devices.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add missing iounmap in error handling code, in a case where the function
already preforms iounmap on some other execution path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
statement S,S1;
int ret;
@@
e = \(ioremap\|ioremap_nocache\)(...)
... when != iounmap(e)
if (<+...e...+>) S
... when any
when != iounmap(e)
*if (...)
{ ... when != iounmap(e)
return ...; }
... when any
iounmap(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tony Lindgren <tony@atomide.com>
pdata needs to be freed before leaving the function in an error case.
A simplified version of the semantic match that finds the problem is as
follows: (http://coccinelle.lip6.fr)
// <smpl>
@r exists@
local idexpression x;
statement S;
identifier f1;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
x->f1
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently MMC2 setup code can only enable loopback clock and
relies on reset value for boards that need to have it disabled.
This causes a problem with certain bootloaders that always enable
that clock, resulting with unwanted bootloader dependencies.
Fix this by making it disable the clock if board data says so.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
hsmmc23_before_set_reg() can set MMCSDIO2ADPCLKISEL bit, which
enables internal clock for MMC2. Currently this function is also called
by code handling MMC3, and if .internal_clock is set in platform data
(by default it currently is), it will set MMCSDIO2ADPCLKISEL for MMC2
instead of MMC3 (MMC3 doesn't have such bit so nothing actually needs to
be done). This breaks 2nd SD slot on pandora.
Fix this by changing hsmmc23_before_set_reg() to only handle MMC2.
Note that this removes .remux() call for MMC3, but no board currently
needs it and it's also not called for MMC4 and MMC5.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
following statement can only change device size from 8-bit(0) to 16-bit(1),
but not vice versa:
regval |= GPMC_CONFIG1_DEVICESIZE(wval);
so as this field has 1 reserved bit, that could be used in future,
just clear both bits and then OR with the desired value
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 2f0778af (ARM: 7205/2: sched_clock: allow sched_clock to be
selected at runtime) had a typo for the case when CONFIG_OMAP_32K_TIMER
is not set.
In dmtimer_read_sched_clock(), wrong argument was getting passed to
__omap_dm_timer_read_counter() function call; instead of "&clksrc",
we were passing "clksrc.io_base", which results into kernel crash.
To reproduce kernel crash, just disable the CONFIG_OMAP_32K_TIMER config
option (and DEBUG_LL) and build/boot the kernel.
This will use dmtimer as a kernel clocksource and lead to kernel
crash during boot -
[ 0.000000] OMAP clocksource: GPTIMER2 at 26000000 Hz
[ 0.000000] sched_clock: 32 bits at 26MHz, resolution 38ns, wraps every
165191ms
[ 0.000000] Unable to handle kernel paging request at virtual address
00030ef1
[ 0.000000] pgd = c0004000
[ 0.000000] [00030ef1] *pgd=00000000
[ 0.000000] Internal error: Oops: 5 [#1] SMP
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 Not tainted (3.3.0-rc1-11574-g0c76665-dirty #3)
[ 0.000000] PC is at dmtimer_read_sched_clock+0x18/0x4c
[ 0.000000] LR is at update_sched_clock+0x10/0x84
[ 0.000000] pc : [<c00243b8>] lr : [<c0018684>] psr: 200001d3
[ 0.000000] sp : c0641f38 ip : c0641e18 fp : 0000000a
[ 0.000000] r10: 151c3303 r9 : 00000026 r8 : 76276259
[ 0.000000] r7 : 00028547 r6 : c065ac80 r5 : 431bde82 r4 : c0655968
[ 0.000000] r3 : 00030ef1 r2 : fb032000 r1 : 00000028 r0 : 00000001
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
PandaBoard has twl6040 codec for audio.
Register the omap4-abe-twl6040 platform device.
Add platform data to enable the twl6040 codec.
Since there is a difference in audio between PandaBoard 4430
and PandaBoard ES (4460):
Use different name for the sound card:
"PandaBoard" for PandaBoard 4430
"PandaBoardES" for PandaBoard ES
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Santosh Shilimkar <santosh.shilimkar@ti.com>
CC: David Anders <x0132446@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
To avoid breakage in audio support with the coming change
in ASoC machine driver (conversion to platfrom device).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
A hardware bug in the OMAP4 HDMI PHY causes physical damage to the board
if the HDMI PHY is kept powered on when the cable is not connected.
This patch solves the problem by adding hot-plug-detection into the HDMI
IP driver. This is not a real HPD support in the sense that nobody else
than the IP driver gets to know about the HPD events, but is only meant
to fix the HW bug.
The strategy is simple: If the display device is turned off by the user,
the PHY power is set to OFF. When the display device is turned on by the
user, the PHY power is set either to LDOON or TXON, depending on whether
the HDMI cable is connected.
The reason to avoid PHY OFF when the display device is on, but the cable
is disconnected, is that when the PHY is turned OFF, the HDMI IP is not
"ticking" and thus the DISPC does not receive pixel clock from the HDMI
IP. This would, for example, prevent any VSYNCs from happening, and
would thus affect the users of omapdss. By using LDOON when the cable is
disconnected we'll avoid the HW bug, but keep the HDMI working as usual
from the user's point of view.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Both Panda and 4430SDP use GPIO 63 as HDMI hot-plug-detect. Configure
this GPIO in the board files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The HDMI GPIO pins LS_OE and CT_CP_HPD are not currently configured.
This patch configures them as output pins.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
"hdmi_hpd" pin is muxed to INPUT and PULLUP, but the pin is not
currently used, and in the future when it is used, the pin is used as a
GPIO and is board specific, not an OMAP4 wide thing.
So remove the muxing for now.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The GPIO 60 on 4430sdp and Panda is not HPD GPIO, as currently marked in
the board files, but CT_CP_HPD, which is used to enable/disable HPD
functionality.
This patch renames the GPIO.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Instead of freeing the GPIOs individually, use gpio_free_array().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
dss_core has to be initialized before any other DSS hwmod. Currently
this is broken as dss_core is listed in chip/revision specific hwmod
lists while other DSS hwmods are listed in common list which is
registered first.
This patch moves DSS hwmods (except for dss_core) to the separate list
which is registered last to ensure that dss_core is already registered.
This solves the problem with BUG() in L3 interrupt handler on boards
with DSS enabled in bootloader.
The long-term fix to this is to ensure modules are set up in dependency
order in the hwmod core code.
CC: Tomi Valkeinen <tomi.valkeinen@ti.com>
CC: Archit Taneja <archit@ti.com>
CC: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
[paul@pwsan.com: add notes that this is just a temporary workaround until
hwmod dependencies are added]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 22f51371f8 ("ARM: OMAP3: pm: use
prcm chain handler") breaks the build on a 2420-only config, due to
a missing include for plat/irqs.h:
CC arch/arm/mach-omap2/prm2xxx_3xxx.o
arch/arm/mach-omap2/prm2xxx_3xxx.c:41:11: error: 'INT_34XX_PRCM_MPU_IRQ' undeclared here (not in a function)
Fix by explicitly including it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Commit 7b250aff1c ("ARM: OMAP: Avoid
cpu_is_omapxxxx usage until map_io is done") breaks the build on a
2420-only config on v3.3-rc1:
arch/arm/mach-omap2/built-in.o: In function `omap2430_init_early':
arch/arm/mach-omap2/io.c:406: undefined reference to `omap2_set_globals_243x'
arch/arm/mach-omap2/io.c:410: undefined reference to `omap243x_clockdomains_init'
arch/arm/mach-omap2/io.c:411: undefined reference to `omap2430_hwmod_init'
Fix by only compiling omap2420_init_early() when CONFIG_SOC_OMAP2420
is selected, and only compiling omap2430_init_early() when
CONFIG_SOC_OMAP2430 is selected.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
To be able to get the memory resources by name from
the DMIC driver (for MPU and for DMA).
Without this patch, functionality that was working in 3.2 breaks in
3.3-rc1. This patch should have gone in as part of the 3.3 merge
window, but was inadvertently missed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[paul@pwsan.com: added commit message note]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
dispc's sysc_flags is missing SYSC_HAS_ENAWAKEUP flag. This seems to
cause SYNC_LOST errors from the DSS when the power management is
enabled.
This patch adds the missing SYSC_HAS_ENAWAKEUP flag. Note that there are
other flags missing also (clock activity, DSI's sysc flags), but as they
are not critical, they will be fixed in the next merge window.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Currently OMAP2 and 3 share the same omap_hwmod_class and
omap_hwmod_class_sysconfig for dispc. However, OMAP3 has sysconfig
bits that OMAP2 doesn't have, so we need to split those structs into
OMAP2 and OMAP3 specific versions.
This patch only splits the structs, without changing the contents.
This is a prerequisite for a subsequent fix.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: added commit note]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
To ensure correct alignment of cacheline-aligned data, the maximum
cacheline size needs to be known at compile time.
Since Cortex-A8 and Cortex-A15 have 64-byte cachelines (and it is likely
that there will be future ARMv7 implementations with the same line size)
then it makes sense to assume that CPU_V7 implies a 64-byte L1 cacheline
size. For CPUs with smaller caches, this will result in some harmless
padding but will help with single zImage work and avoid hitting subtle
bugs with misaligned data structures.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When this is the only content remaining in mach/system.h then the
whole file is removed.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-and-tested-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: David Brown <davidb@codeaurora.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Now that all implementations of arch_idle() are equivalent to cpu_do_idle()
we can just use the later directly and stop including mach/system.h.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-and-tested-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
warning: (MACH_OMAP3_TOUCHBOOK && DRM_RADEON_KMS && DRM_I915 &&
STUB_POULSBO && FB_BACKLIGHT && USB_APPLEDISPLAY && FB_OLPC_DCON &&
ASUS_LAPTOP && SONY_LAPTOP && THINKPAD_ACPI && EEEPC_LAPTOP &&
ACPI_ASUS && ACPI_CMPC && SAMSUNG_Q10) selects BACKLIGHT_CLASS_DEVICE
which has unmet direct dependencies (HAS_IOMEM && BACKLIGHT_LCD_SUPPORT)
A lot of boards need BACKLIGHT_CLASS_DEVICE for the framebuffers to
work, but it's not *needed* for the device itself. It might be nice to
enable it by default somewhoe if graphics stuff is enabled, but that's
another story.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'fixes' of git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-arm:
ARM: sa11x0: assabet: fix build warning
ARM: Add arm_memblock_steal() to allocate memory away from the kernel
ARM: 7275/1: LPAE: Check the CPU support for the long descriptor format
ARM: 7274/1: NUC900: Rename nuc900-audio platform device to nuc900-ac97
ARM: 7272/1: S3C24XX: Fix build error for missing <mach/system-reset.h>
ARM: 7271/1: Fix typo in conversion of ARCH_NR_GPIOS to Kconfig
