Redefine acpi_companion_match() to return an ACPI device object
pointer instead of a bool and use it to remove some redundant code
from acpi_match_device().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Redefine the function used for matching the device's "compatible"
property against a given list of "compatible" strings to take
a pointer to that list instead of a driver object pointer to
make it more general.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
kvm_write_guest_cached() does not mark all written pages as dirty and
code comments in kvm_gfn_to_hva_cache_init() talk about NULL memslot
with cross page accesses. Fix all the easy way.
The check is '<= 1' to have the same result for 'len = 0' cache anywhere
in the page. (nr_pages_needed is 0 on page boundary.)
Fixes: 8f964525a1 ("KVM: Allow cross page reads and writes from cached translations.")
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Message-Id: <20150408121648.GA3519@potion.brq.redhat.com>
Reviewed-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* pci/misc:
PCI: Read capability list as dwords, not bytes
PCI: Don't clear ASPM bits when the FADT declares it's unsupported
PCI: Clarify policy for vendor IDs in pci.txt
PCI/ACPI: Optimize device state transition delays
PCI: Export pci_find_host_bridge() for use inside PCI core
PCI: Make a shareable UUID for PCI firmware ACPI _DSM
PCI: Fix typo in Thunderbolt kernel message
To avoid probing in unintended binary, the orphaned -x option must be
checked and warned.
Without this patch, following command sets up the probe in the kernel.
-----
# perf probe -a strcpy -x ./perf
Added new event:
probe:strcpy (on strcpy)
You can now use it in all perf tools, such as:
perf record -e probe:strcpy -aR sleep 1
-----
But in this case, it seems that the user may want to probe in the perf
binary. With this patch, perf-probe correctly handles the orphaned -x.
-----
# perf probe -a strcpy -x ./perf
Error: -x/-m must follow the probe definitions.
...
-----
Reported-by: Jiri Olsa <jolsa@redhat.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150401102541.17137.75477.stgit@localhost.localdomain
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Support multiple probes on different binaries with just
one command.
In the result, this example sets up the probes on icmp_rcv in
kernel, on main and set_target in perf, and on pcspkr_event
in pcspker.ko driver.
-----
# perf probe -a icmp_rcv -x ./perf -a main -a set_target \
-m /lib/modules/4.0.0-rc5+/kernel/drivers/input/misc/pcspkr.ko \
-a pcspkr_event
Added new event:
probe:icmp_rcv (on icmp_rcv)
You can now use it in all perf tools, such as:
perf record -e probe:icmp_rcv -aR sleep 1
Added new event:
probe_perf:main (on main in /home/mhiramat/ksrc/linux-3/tools/perf/perf)
You can now use it in all perf tools, such as:
perf record -e probe_perf:main -aR sleep 1
Added new event:
probe_perf:set_target (on set_target in /home/mhiramat/ksrc/linux-3/tools/perf/perf)
You can now use it in all perf tools, such as:
perf record -e probe_perf:set_target -aR sleep 1
Added new event:
probe:pcspkr_event (on pcspkr_event in pcspkr)
You can now use it in all perf tools, such as:
perf record -e probe:pcspkr_event -aR sleep 1
-----
Reported-by: Arnaldo Carvalho de Melo <acme@infradead.org>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150401102539.17137.46454.stgit@localhost.localdomain
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
commit: f3b623b849 ("perf tools: Reference count struct thread")
appends every thread->node to dead_threads in machine__remove_thread()
and list_del_init() this node in thread__put().
perf_event__exit_del_thread() releases thread wihout using
machine__remove_thread(), and causes a NULL pointer crash when
list_del_init(&thread->node) is called. Fix this by using
machine_remove_thread() instead of using thread__put() directly.
This problem can be reproduced as following:
$ perf record ls
$ perf buildid-list --with-hits
[ 3874.195070] perf[1018]: segfault at 0 ip 00000000004b0b15 sp
00007ffc35b44780 error 6 in perf[400000+166000]
Segmentation fault
After this patch:
$ perf record ls
$ perf buildid-list --with-hits
bc23e7c3281e542650ba4324421d6acf78f4c23e /proc/kcore
643324cb0e969f30c56d660f167f84a150845511 [vdso]
0000000000000000000000000000000000000000 /bin/busybox
...
Signed-off-by: He Kuang <hekuang@huawei.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1428658500-6483-1-git-send-email-hekuang@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Trying to analyze a big endian data file on little endian system fails
with the error:
0xa9b40 [0x70]: failed to process type: 9
The problem is that header parsing is not done correctly because the
file attributes are not swapped. Make it so. With this patch able to
analyze a sparc64 data file on x86_64.
Signed-off-by: David Ahern <david.ahern@oracle.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/1428610546-178789-1-git-send-email-david.ahern@oracle.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When traversing /proc to synthesize the PERF_RECORD_FORK et al events we
were bailing out on errors without calling closedir(), fix it.
Reported-by: David Ahern <dsahern@gmail.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-vxtp593rfztgbi8noy0m967p@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Commit ca6c41c59b sets the ppid based on what is read from the
/proc/pid/status file when synthesizing fork events.
This is correct thing to do for new processes but not threads of a
process.
Fix ppid for threads to be the main thread when synthesizing fork events
(ie., assume main thread spawned all sub-threads in a process).
Reported-by: Arnaldo Carvalho de Melo <arnaldo.melo@gmail.com>
Signed-off-by: David Ahern <david.ahern@oracle.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Don Zickus <dzickus@redhat.com>
Link: http://lkml.kernel.org/r/1428598107-178999-1-git-send-email-david.ahern@oracle.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Ran checkpatch.pl on file and removed a warning about an unwanted space before
a tab.
Signed-off-by: Chase Metzger <chasemetzger15@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
msleep(USB_RESUME_TIMEOUT) must be done when the controller drives
the resume. This is true after HPRT0_RES is written.
Moreover, restore the delay after controller power is up.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Forbid dumpping registers when the controller in low power mode
- dp pullup needs to be controlled by fsm when working at otg
fsm mode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVJM1NAAoJEEhZKYFQ1nG7s80IALrPTj0ZqVmH5FjWQt49I7Bj
Q2UAFDvINhSufJynlcHbVB0G6XbEtn/T+5Qnx8WJhDqnODgI9CGk+WsFPmJilrj6
DCvTaUsCNK3ERK1yBGqUIE+gV/ku2NYO+BnKA2Leh2Vb+/KENTs2v+Lr1sRd5qMO
u7kmyZlID997A4h2RDW23oJgynPlTTgwg26VXGshCmeqH4UnoLQ1Gfm3+iQ1ItsM
9Ka6HKJTqP9tBYh/mgI4G7If6EI+L4EVH1Hyfy8uConwcbkyaKRA8cR1o0at/A4s
Npoma8NVw7PMit1cMwzEUECbfY3fjVQLI4j1PTDsWdRvDKxqCHre64erq/NH+g4=
=zOdE
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
Two Chipidea updates
- Forbid dumpping registers when the controller in low power mode
- dp pullup needs to be controlled by fsm when working at otg
fsm mode
============
*) Add driver for USB PHYs on sun9i
*) Add driver for USB PHY on dm816x
*) Modified exynos5-usbdrd driver to add support for Exynos5433 SoC
Fixes
=====
*) Fix power_on/power_off failure paths in some drivers
*) Make miphy365x use generic PHY type constants
*) Fix build errors due to missing export symbols in qcom-ufs driver
*) Make all the functions return proper error values
Cleanups
========
*) use PTR_ERR_OR_ZERO to simplify code
*) use devm_kcalloc instead of devm_kzalloc with multiply
*) remove un-necessary ifdef CONFIG_OF
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=0gB+
-----END PGP SIGNATURE-----
Merge tag 'for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
New Features
============
*) Add driver for USB PHYs on sun9i
*) Add driver for USB PHY on dm816x
*) Modified exynos5-usbdrd driver to add support for Exynos5433 SoC
Fixes
=====
*) Fix power_on/power_off failure paths in some drivers
*) Make miphy365x use generic PHY type constants
*) Fix build errors due to missing export symbols in qcom-ufs driver
*) Make all the functions return proper error values
Cleanups
========
*) use PTR_ERR_OR_ZERO to simplify code
*) use devm_kcalloc instead of devm_kzalloc with multiply
*) remove un-necessary ifdef CONFIG_OF
This part 2 pull request contains only the patches
which make sure everybody on linux uses the same
resume timeout value.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=RqsO
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing
Felipe writes:
usb: generic resume timeout for v4.1
This part 2 pull request contains only the patches
which make sure everybody on linux uses the same
resume timeout value.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch updates the binding information to reflect the
extra dt options which are now supported by the sdhci-st.c
driver which enable support for stih407 family silicon.
STiH410 SoC and later support UHS modes for eMMC, so the
driver now makes use of these common bindings. Examples
are provided for both eMMC (which has additional bindings)
and also sd slot for STiH407.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some additional quirks need to be enabled now we support UHS
modes. This avoids some spurious warnings like
"Got data interrupt 0x00000002 even though no data operation was in progress"
Testing on stih410-b2120 board achieves the following speeds
with HS200 eMMC card.
max-frequency = 200Mhz
/dev/mmcblk0p1:
Timing buffered disk reads: 270 MB in 3.02 seconds = 89.54 MB/sec
max-frequency = 100Mhz
root@debian-armhf:~# hdparm -t /dev/mmcblk0p1
/dev/mmcblk0p1:
Timing buffered disk reads: 210 MB in 3.00 seconds = 70.00 MB/sec
max-frequency = 50Mhz
root@debian-armhf:~# hdparm -t /dev/mmcblk0p1
/dev/mmcblk0p1:
Timing buffered disk reads: 118 MB in 3.00 seconds = 39.28 MB/sec
This is better than the 3.10 kernel which achieves 77.59 MB/sec
at 200Mhz clock (same board/soc/eMMC).
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To allow UHS modes to work properly we need to provide the st specific
set_uhs_signaling callback function. This function differs from the
generic sdhci_set_uhs_signaling callback in that we need to configure
the correct delay depending on the UHS mode, and also set the V18_EN
bit.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
STiH407 family SoC's have glue registers in the flashSS subsystem which
are used to configure the Arasan HC. This patch configures these glue
registers according to what has been specified in the DT.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Due to the tight timing constraints in some UHS modes, it is required to have
some delay management in the design. Two types of delay management are supported
in the HW: -
1) Static delay management
2) Dynamic delay management
NB: The delay management is only there when eMMC interface is selected.
1: Static delay management: is used to provide PVT dependent static delay on the
clock/data lines to manage setup/hold requirements of the interface. The maximum
delay possible is 3.25ns. These delays are PVT dependent, and thus delay values
applied are not accurate and vary across provcess voltage and temperature range.
Due to this these delays must not be used on the very time critical paths.
2. Dynamic delay locked loop (DLL): is used to provide dynamic delay management.
The advantage of DLL is that it provides accurate & PVT indepedent delay.
The DLL is used to provide delay on the loopback clock on "Read Path" to capture
read data reliably. On TX path the clock on which output data is transmitted is
delayed, resulting in delay of TX data.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
STiH407 family SoC's can have a reset signal for the controller which needs to
be managed. Also the eMMC controller has some additional 'top' memory mapped
registers which are used to manage the dynamic and static delay required for
UHS modes. This patch adds support for creating the mapping, which will be used
by subsequent patches.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The stih407 family SoC's have additional glue registers in the flashSS which
are used to configure the Arasan controller.
This patch adds macros for the register offsets and bitfields which will be
used by subsequent patches to support stih407 family SoC's.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Both ARM946 and ARM940 setup functions were corrupting r1 and r2,
which is not permissible - these are used to carry the machine ID
and boot data into the kernel, and must be preserved.
The code responsible for this was the same in both files: they were
using the registers to generate a protection region register value.
Fix this by turning this process into a macro, and using that macro
in both these files with an alternative register allocation. r0,
r3 and r7 can be used for temporary values here.
Reported-by: Alex Dumitrache <broscutamaker@gmail.com>
Tested-by: Georg Hofstetter <g3gg0.de@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the check for UV2000/3000. Note when the HUB is not recognized.
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Hedi Berriche <hedi@sgi.com>
Acked-by: Dimitri Sivanich <sivanich@sgi.com>
Link: http://lkml.kernel.org/r/20150409182629.267239403@asylum.americas.sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fix a bug in the OEM check function that determines if the
system is a UV system and the BIOS is compatible with the
kernel's UV apic driver. This prevents some possibly obscure
panics and guards the system against being started on SGI
hardware that does not have the required kernel support.
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Hedi Berriche <hedi@sgi.com>
Acked-by: Dimitri Sivanich <sivanich@sgi.com>
Link: http://lkml.kernel.org/r/20150409182629.112998930@asylum.americas.sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Optimize the first "SGI" OEM check to return faster if the
system is not an SGI or UV system.
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Hedi Berriche <hedi@sgi.com>
Acked-by: Dimitri Sivanich <sivanich@sgi.com>
Link: http://lkml.kernel.org/r/20150409182628.952357922@asylum.americas.sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The ixgbe driver hasn't used call_rcu to free the rings for some time now.
Since that is the case the call to rcu_barrier can be dropped since calls
to kfree_rcu don't require it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that the HW_VLAN_CTAG_FILTER bit is not falsely
advertised as being a feature that can be toggled on ixgbe parts. The
driver was setting the bit in features and letting it be inherited by
hw_features, however the driver was actually ignoring the value of the bit
and just assuming it was always set. As a result VLAN filtering was always
enabled which is a requirement for SR-IOV, VMDq, DCB, FCoE, and possibly
other features within the adapters.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adds x550 specific FCoE offloads for DDP context programming and
increased DDP exchanges.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch will enable X550 Source Address Prunning for VEPA
bridge mode. This requires that we also have replication enabled
as well, while in this mode.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch gathers together all the logic needed to configure bridge
modes. Currently that it is rather simple but this is really laying
the ground work for future X550 feature enhancement.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit 20d0189b10
in v3.14-rc1 RAID0 has performed incorrect calculations
when the chunksize is not a power of 2.
This happens because "sector_div()" modifies its first argument, but
this wasn't taken into account in the patch.
So restore that first arg before re-using the variable.
Reported-by: Joe Landman <joe.landman@gmail.com>
Reported-by: Dave Chinner <david@fromorbit.com>
Fixes: 20d0189b10
Cc: stable@vger.kernel.org (3.14 and later).
Signed-off-by: NeilBrown <neilb@suse.de>
We are currently storing our BRIDGE_MODE as a bit in our adapter flags.
This patch will store the actual mode instead which minimizes obfuscation
and makes following patches for X550 simpler.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move documentation into this century, even if this device hasn't
been available for some time.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The MTU values in the documentation do not match the source.
The source has frame limit of IXGBE_MAX_JUMBO_FRAME_SIZE (9728)
which is MTU of 9710 because of the accounting for Ethernet header
and CRC.
Also, don't refer to the obsolete ifconfig command.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ifconfig command is obsolete, best to remove all references so that
new users learn ip.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the end address checking for flushda function. We need to flush
each address line for flushda instruction, from start to end address.
This is because flushda instruction only flush the cache if tag and line
fields are matched.
Change to use ldwio instruction (bypass cache) to load the instruction
that causing trap. Our interest is the actual instruction that executed
by the processor, this should be uncached.
Note, EA address might be an userspace cached address.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
- Revert a 3.17 hibernate commit that was supposed to fix an issue
related to e820 reserved regions, but broke resume from hibernation
on Lenovo x230 (Rafael J Wysocki).
- Prevent the ACPI cpuidle driver from overwriting the name and
description of the C0 state set by the core when the list of
C-states changes (Thomas Schlichter).
- Remove the no longer needed state_count field from struct cpuidle_device
which prevents the list of C-states shown by the sysfs interface from
becoming incorrect when the current number of them is different from
the number of C-states on boot (Bartlomiej Zolnierkiewicz).
- The cpufreq core updates the policy object of the only online CPU
during system resume to make it reflect the current hardware state,
but it always assumes that CPU to be CPU0 which need not be the
case, so fix the code to avoid that assumption (Viresh Kumar).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=g0eu
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.0-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These are stable-candidate fixes of some recently reported issues in
the cpufreq core, cpuidle core, the ACPI cpuidle driver and the
hibernate core.
Specifics:
- Revert a 3.17 hibernate commit that was supposed to fix an issue
related to e820 reserved regions, but broke resume from hibernation
on Lenovo x230 (Rafael J Wysocki).
- Prevent the ACPI cpuidle driver from overwriting the name and
description of the C0 state set by the core when the list of
C-states changes (Thomas Schlichter).
- Remove the no longer needed state_count field from struct
cpuidle_device which prevents the list of C-states shown by the
sysfs interface from becoming incorrect when the current number of
them is different from the number of C-states on boot (Bartlomiej
Zolnierkiewicz).
- The cpufreq core updates the policy object of the only online CPU
during system resume to make it reflect the current hardware state,
but it always assumes that CPU to be CPU0 which need not be the
case, so fix the code to avoid that assumption (Viresh Kumar)"
* tag 'pm+acpi-4.0-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "PM / hibernate: avoid unsafe pages in e820 reserved regions"
cpuidle: ACPI: do not overwrite name and description of C0
cpuidle: remove state_count field from struct cpuidle_device
cpufreq: Schedule work for the first-online CPU on resume
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-04-09
We've had enough new patches during the past week (especially from
Marcel) that it'd be good to still get these queued for 4.1.
The majority of the changes are from Marcel with lots of cleanup &
refactoring patches for the HCI UART driver. Marcel also split out some
Broadcom & Intel vendor specific functionality into two new btintel &
btbcm modules.
In addition to the HCI driver changes there's the completion of our
local OOB data interface for pairing, added support for requesting
remote LE features when connecting, as well as a couple of minor fixes
for mac802154.
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lookup key for tcp_md5_do_lookup() has to be taken
from addr_sk, not sk (which can be the listener)
Fixes: fd3a154a00 ("tcp: md5: get rid of tcp_v[46]_reqsk_md5_lookup()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reading both the capability ID and "next" pointer at the same time lets us
parse the list with half the number of config reads.
Signed-off-by: Sean O. Stalley <sean.stalley@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tom Lendacky says:
====================
amd-xgbe: AMD XGBE driver updates 2015-04-09
The following series of patches includes functional updates and changes
to the driver.
- Allow ethtool rx-frames coalescing to be changed while the device is up
- Consolidate initialization routine into the init function
- Add support for the TX watchdog timeout
This patch series is based on net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to be able to detect a hung Tx task by adding the netdev
ndo_tx_timeout function callback. Do not set the watchdog_timeo value
so as to use the system default time (currently 5 seconds).
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently a call to configure the Rx mode (promiscuous mode, all
multicast mode, etc.) is made in xgbe_start separate from the xgbe_init
function. This call to set the Rx mode should be part of the xgbe_init
function so that calls to the init function don't have to be preceded
with calls to configure the Rx mode.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the device must be down in order to update the rx-frames
coalescing setting because the interrupt indicator is set in the
descriptor data during initialization. Allow this setting to be changed
while the device is up by moving the interrupt decision into the
descriptor reset function and base the decision off of the supplied
descriptor index value.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an FDB entry is added or deleted the information about VLAN
is not passed to listening applications like 'bridge monitor fdb'.
With this patch VLAN ID is passed if it was set in the original
netlink message.
Also remove an unused bdev variable.
Signed-off-by: Hubert Sokolowski <hubert.sokolowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
