Gen2 doesn't have the ring idle/stop bits in the SCPD/MI_MODE register,
so don't go spewing warnings about the state of those bits.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the user tries to mmap through the GTT an object that is marked as
snooped, we report an error rather than allow the GPU to hang the
machine. The choice of EINVAL, however, was unfortunate as we turn that
into a WARN rather than a quiet SIGBUS.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the MI_ARB_STATE MI_ARB_C3_LP_WRITE_ENABLE setup to
gen3_init_clock_gating() from i915_gem_load() when KMS is enabled. Leave
it in i915_gem_load() for the UMS case, but add an explcit check, just
to make it easier to spot it when we eventually rip out UMS support.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
85x also has a similar AGPBUSY# bit as gen3. Enable it to make
sure vblank interrupts don't get dealyed during C3 state.
There's also another bit which controls whether AGPBUSY# is asserted
based on pending cacheable cycles and interrupts, or just based on
pending commands in the ring and interrupts. Select the cacheable
cycles mode since that seems to be the new way of doing things in
85x, and it does give slightly better C3 residency numbers with
glxgears running.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
My Gen3 Bspec lists the AGPBUSY# bit in INSTPM as an enable bit rather
than a disable bit. Our code has the opposite idea. Make the code match
the spec.
Might fix some gen3 C3 related interrupt delivery problems. Untested
due to lack of hardware.
v2: call it AGPBUSY_INT_EN to make it clearer it has to do with interrupts
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I don't see why we wouldn't want interrupts to wake up the CPU from C3
always, so just set the AGPBUSY# bit in gen3_init_clock_gating().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When doing this, all PLLs should be disabled.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to do this anytime we power gate the DPIO common well.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There may be a dependency here.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This needs to be done before we power back on the CMN_BC well so the PHY
can calibrate properly.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We do this at runtime and later on now.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is a bit like the CMN reset de-assert we do in DPIO_CTL, except
that it resets the whole common lane section of the PHY. This is
required on machines where the BIOS doesn't do this for us on boot or
resume to properly re-calibrate and get the PHY ready to transmit data.
Without this patch, such machines won't resume correctly much of the time,
with the symptom being a 'port ready' timeout and/or a link training
failure.
Note that simply asserting reset at suspend and de-asserting at resume
is not sufficient, nor is simply de-asserting at boot. Both of these
cases have been tested and have still been found to have failures on
some configurations.
v2: extract simpler set_power_well function for use in reset_dpio (Imre)
move to reset_dpio (Daniel & Ville)
v3: don't reset if DPIO reset is already de-asserted (Imre)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we disable first the port (by disabling DPI) and only then the
display pipe the pipe-off flag will never be set, possibly leading to a
hanged pipe state at the next modeset-enable.
Note that according to the VLV2 display cluster HAS, we should disable
the port before the pipe. This doesn't seem to match reality based on
the above and it's also asymmetric with the enabling sequence, where we
first enable the port and then the pipe.
v2:
- send the panel shutdown command before stopping the pipe, since this
is the recommended sequence (Shobhit)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It seems by default the VBT has MIPI configuration block as well. The
Generic driver will assume always MIPI if MIPI configuration block is found.
This is causing probelm when actually there is eDP. Fix this by looking
into general definition block which will have device configurations. From here
we can figure out what is the LFP type and initialize MIPI only if MIPI
is found.
v2: Addressed review comments by Damien
- Moved PORT definitions to intel_bios.h and renamed as DVO_PORT_MIPIA
- renamed is_mipi to has_mipi and moved definition as suggested
- Check has_mipi inside parse_mipi and intel_dsi_init insted of outside
v3: Make has_mipi as a bitfield as suggested
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: fold in conditions to pack everything neatly below 80 chars.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For disabling L3 clock gating we need to set bit 25 of MMIO
register 940c. Earlier this was being done by just writing 1
into bit 25 and resetting all other bits.
This patch modifies the routine to read-modify-write of the
register, so that the values of other bits are not destroyed.
v2: Modifying the comments and the patch commit message (Chris)
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Sourab Gupta <sourab.gupta@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Apply checkpatch fixup.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This driver makes use of the generic panel information from the VBT.
Panel information is classified into two - panel configuration and panel
power sequence which is unique to each panel. The generic driver uses the
panel configuration and sequence parsed from VBT block #52 and #53
v2: Address review comments by Jani
- Move all of the things in driver c file from header
- Make all functions static
- Make use of video/mipi_display.c instead of redefining
- Null checks during sequence execution
v3: Address review comments by Damien
- Rename the panel driver file as intel_dsi_panel_vbt.c
- Fix style changes as suggested
- Correct comments for lp->hs and hs->lp count calculations
- General updating comments to have more clarity
- using max() instead of ternary operator
- Fix names (ui_num, ui_den) while using UI in calculations
- compute max of lp_to_hs switch and hs_to_lp switch while computing
hs_lp_switch_count
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fallout from an intermediate patch revision that I deemed worth saving.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we do a full re-init of all interrupts after a gpu hang.
Which is pretty bad since we don't restore the interrupts we've
enabled at runtime correctly. Even with that addressed it's rather
horribly race.
But on g4x and later we only reset the gt and not the entire gpu.
Which means we only need to reset the GT interrupt bits. Which has the
nice benefit that vblank waits, pipe CRC interrupts and everything
else display related just keeps on working.
The downside is that gt interrupt handling (i.e. ring->get/put_irq) is
still racy. But as long as the gpu hang reliably wakes all waters and
we have a short time where the refcount drops to 0 we'll recover. So
not that bad really.
v2: Ville noticed that GTIMR and PMIMR don't get cleared, only the
subordinate per-ring registers. So let's rip out all the interrupt dancing.
The FIXME comment is still required though since the ring irq handling
happens at the per-ring interrupt mask registers, too.
Testcase: igt/kms_flip/vblank-vs-hang
Testcase: igt/kms_pipe_crc_basic/hang-*
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville figured out that it needs a full display reset since apparently
a lot more goes down than just the GT. Until that's address it's
better to just diable gpu reset.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So apparently this is tricky.
We need to consider:
- We start out with all the hw enabling bits disabled, both the
individual fifo underrun interrupts and the shared display error
interrupts masked. Otherwise if the bios config is broken we'll blow
up with a NULL deref in our interrupt handler since the crtc
structures aren't set up yet at driver load time.
- On gmch we need to mask fifo underruns on the sw side, so always
need to set that in sanitize_crtc for those platforms.
- On other platforms we try to set the sw tracking so that it reflects
the real state. But since a few platforms have shared bits we must
_not_ disable fifo underrun reporting. Otherwise we'll never enable
the shared error interrupt.
This is the state before out patch, but unfortunately this is not good
enough. But after a suspend resume operation this is broken:
1. We don't enable the hw interrupts since the same code runs on
resume as on driver load.
2. The fifo underrun state adjustments we do in sanitize_crtc doesn't
fire on resume since (except for hilarious firmware) all pipes are off
at that point. But they also don't hurt since the subsequent crtc
enabling due to force_restore will enable fifo underruns.
Which means when we enable fifo underrun reporting we notice that the
per-crtc state is already correct and short-circuit everthing out. And
the interrupt doesn't get enabled.
A similar problem would happen if the bios doesn't light up anything
when the driver loads. Which is exactly what happens when we reload
the driver since our unload functions disables all outputs.
Now we can't just rip out the short-circuit logic and unconditionally
update the fifo underrun reporting interrupt masking: We have some
checks for shared error interrupts to catch issues that happened when
the shared error interrupt was disabled.
The right fix is to push down this logic so that we can always update
the hardware state, but only check for missed fifo underruns on a real
enabled->disabled transition and ignore them when we're already
disabled.
On platforms with shared error interrupt the pipe CRC interrupts are
grouped together with the fifo underrun reporting this fixes pipe CRC
support after suspend and driver reloads.
Testcase: igt/kms_pipe_crc_basic/suspend-*
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On platforms with shared interrupt enable bits (which are shared even
with the pipe CRC logic) there's some tricky corner cases. Add
information to make debugging those easier.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We pass actual buffer size to opal_validate_flash() OPAL API call
and in return it contains output buffer size.
Commit cc146d1d (Fix little endian issues) missed to set the size
param before making OPAL call. So firmware image validation fails.
This patch sets size variable before making OPAL call.
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Tested-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The hcall macros may call out to c code for tracing, so we need
to set up a valid r2. This fixes an oops found when testing
ibmvscsi as a module.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
__clear_user and copy_page load from the TOC and are also exported
to modules. This means we have to use _GLOBAL_TOC() so that we
create the global entry point that sets up the TOC.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc sets a low SECTION_SIZE_BITS to accomodate small pseries
boxes. We default to 16MB memory blocks, and boxes with a lot
of memory end up with enormous numbers of sysfs memory nodes.
Set a more reasonable default for powernv of 256MB.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The pseries platform code unconditionally overrides
memory_block_size_bytes regardless of the running platform.
Create a ppc_md hook that so each platform can choose to
do what it wants.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
struct OpalMemoryErrorData is passed to us from firmware, so we
have to byteswap it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When eeh is not enabled, and hotplug two pci devices on the same bus, eeh
related sysfs would be added twice for the first added pci device. Since the
eeh_dev is not created when eeh is not enabled.
This patch adds the check, if eeh is not enabled, eeh sysfs will not be
created.
After applying this patch, following warnings are reduced:
sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:00.0/eeh_mode'
sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:00.0/eeh_config_addr'
sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:00.0/eeh_pe_config_addr'
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
commit 8f9c0119d7 (compat: fs: Generic compat_sys_sendfile
implementation) changed the PowerPC 64bit sendfile call from
sys_sendile64 to sys_sendfile.
Unfortunately this broke sendfile of lengths greater than 2G because
sys_sendfile caps at MAX_NON_LFS. Restore what we had previously which
fixes the bug.
Cc: stable@vger.kernel.org
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This provides debugfs files to access the LPC bus on Power8
non-virtualized using the appropriate OPAL firmware calls.
The usage is simple: one file per space (IO, MEM and FW),
lseek to the address and read/write the data. IO and MEM always
generate series of byte accesses. FW can generate word and dword
accesses if aligned properly.
Based on an original patch from Rob Lippert and reworked.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We had a mix & match of flags used when creating legacy ports
depending on where we found them in the device-tree. Among others
we were missing UPF_SKIP_TEST for some kind of ISA ports which is
a problem as quite a few UARTs out there don't support the loopback
test (such as a lot of BMCs).
Let's pick the set of flags used by the SoC code and generalize it
which means autoconf, no loopback test, irq maybe shared and fixed
port.
Sending to stable as the lack of UPF_SKIP_TEST is breaking
serial on some machines so I want this back into distros
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: stable@vger.kernel.org
This patch adds some documentation on the different cpu families
supported by arch/powerpc.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are a couple of places where xmon is using %x to print values that
are unsigned long.
I found this out the hard way recently:
0:mon> p c000000000d0e7c8 c00000033dc90000 00000000a0000089 c000000000000000
return value is 0x96300500
Which is calling find_linux_pte_or_hugepte(), the result should be a
kernel pointer. After decoding the page tables by hand I discovered the
correct value was c000000396300500.
So fix up that case and a few others.
We also use a mix of 0x%x, %x and %u to print cpu numbers. So
standardise on 0x%x.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When running as a powernv "host" system on P8, we need to switch
the endianness of interrupt handlers. This does it via the appropriate
call to the OPAL firmware which may result in just switching HID0:HILE
but depending on the processor version might need to do a few more
things. This call must be done early before any other processor has
been brought out of firmware.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The default root is allocated and initialized at boot phase, so we
shouldn't destroy the default root when it's umounted, otherwise
it will lead to disaster.
Just try mount and then umount the default root, and the kernel will
crash immediately.
v2:
- No need to check for CSS_NO_REF in cgroup_get/put(). (Tejun)
- Better call cgroup_put() for the default root in kill_sb(). (Tejun)
- Add a comment.
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
All drm_fb_helper_restore_fbdev_mode() call sites, save one, do the same
locking. Simplify this into drm_fb_helper_restore_fbdev_mode_unlocked().
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Merge misc updates from Andrew Morton:
- a few fixes for 3.16. Cc'ed to stable so they'll get there somehow.
- various misc fixes and cleanups
- most of the ocfs2 queue. Review is slow...
- most of MM. The MM queue is pretty huge this time, but not much in
the way of feature work.
- some tweaks under kernel/
- printk maintenance work
- updates to lib/
- checkpatch updates
- tweaks to init/
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (276 commits)
fs/autofs4/dev-ioctl.c: add __init to autofs_dev_ioctl_init
fs/ncpfs/getopt.c: replace simple_strtoul by kstrtoul
init/main.c: remove an ifdef
kthreads: kill CLONE_KERNEL, change kernel_thread(kernel_init) to avoid CLONE_SIGHAND
init/main.c: add initcall_blacklist kernel parameter
init/main.c: don't use pr_debug()
fs/binfmt_flat.c: make old_reloc() static
fs/binfmt_elf.c: fix bool assignements
fs/efs: convert printk(KERN_DEBUG to pr_debug
fs/efs: add pr_fmt / use __func__
fs/efs: convert printk to pr_foo()
scripts/checkpatch.pl: device_initcall is not the only __initcall substitute
checkpatch: check stable email address
checkpatch: warn on unnecessary void function return statements
checkpatch: prefer kstrto<foo> to sscanf(buf, "%<lhuidx>", &bar);
checkpatch: add warning for kmalloc/kzalloc with multiply
checkpatch: warn on #defines ending in semicolon
checkpatch: make --strict a default for files in drivers/net and net/
checkpatch: always warn on missing blank line after variable declaration block
checkpatch: fix wildcard DT compatible string checking
...
For atomic, it will be quite necessary to not need to care so much
about locking order. And 'state' gives us a convenient place to stash a
ww_ctx for any sort of update that needs to grab multiple crtc locks.
Because we will want to eventually make locking even more fine grained
(giving locks to planes, connectors, etc), split out drm_modeset_lock
and drm_modeset_acquire_ctx to track acquired locks.
Atomic will use this to keep track of which locks have been acquired
in a transaction.
v1: original
v2: remove a few things not needed until atomic, for now
v3: update for v3 of connection_mutex patch..
v4: squash in docbook
v5: doc tweaks/fixes
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This should avoid races between connector probing and HPD
irqs in the future, currently mode_config.mutex blocks this
possibility.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
autofs_dev_ioctl_init is only called by __init init_autofs4_fs
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Ian Kent <raven@themaw.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1. Remove CLONE_KERNEL, it has no users and it is dangerous.
The (old) comment says "List of flags we want to share for kernel
threads" but this is not true, we do not want to share ->sighand by
default. This flag can only be used if the caller is sure that both
parent/child will never play with signals (say, allow_signal/etc).
2. Change rest_init() to clone kernel_init() without CLONE_SIGHAND.
In this case CLONE_SIGHAND does not really hurt, and it looks like
optimization because copy_sighand() can avoid kmem_cache_alloc().
But in fact this only adds the minor pessimization. kernel_init()
is going to exec the init process, and de_thread() will need to
unshare ->sighand and do kmem_cache_alloc(sighand_cachep) anyway,
but it needs to do more work and take tasklist_lock and siglock.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a module is built into the kernel the module_init() function
becomes an initcall. Sometimes debugging through dynamic debug can
help, however, debugging built in kernel modules is typically done by
changing the .config, recompiling, and booting the new kernel in an
effort to determine exactly which module caused a problem.
This patchset can be useful stand-alone or combined with initcall_debug.
There are cases where some initcalls can hang the machine before the
console can be flushed, which can make initcall_debug output inaccurate.
Having the ability to skip initcalls can help further debugging of these
scenarios.
Usage: initcall_blacklist=<list of comma separated initcalls>
ex) added "initcall_blacklist=sgi_uv_sysfs_init" as a kernel parameter and
the log contains:
blacklisting initcall sgi_uv_sysfs_init
...
...
initcall sgi_uv_sysfs_init blacklisted
ex) added "initcall_blacklist=foo_bar,sgi_uv_sysfs_init" as a kernel parameter
and the log contains:
blacklisting initcall foo_bar
blacklisting initcall sgi_uv_sysfs_init
...
...
initcall sgi_uv_sysfs_init blacklisted
[akpm@linux-foundation.org: tweak printk text]
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Weinberger <richard.weinberger@gmail.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Josh Boyer <jwboyer@fedoraproject.org>
Cc: Rob Landley <rob@landley.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pertially revert commit ea676e846a ("init/main.c: convert to
pr_foo()").
Unbeknownst to me, pr_debug() is different from the other pr_foo()
levels: pr_debug() is a no-op when DEBUG is not defined.
Happily, init/main.c does have a #define DEBUG so we didn't break
initcall_debug. But the functioning of initcall_debug should not be
dependent upon the presence of that #define DEBUG.
Reported-by: Russell King <rmk@arm.linux.org.uk>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
old_reloc() is only used in this file, make it static.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All KERN_DEBUG callsites being under #ifdef DEBUG we can safely convert
everything to pr_debug without changing current behaviour.
Remove #ifdef DEBUG around pr_debugs only (suggested by Joe Perches)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
