Secondary unicast MAC addresses will get deleted only when the interface is UP.
When the interface is DOWN, though these secondary MAC addresses are unusable
and awaiting to be deleted, cause the firmware to believe that they are being used.
If the user intends to set a MAC address as primary MAC from one of these
secondary MAC addresses, the firmware returns a MAC address Collision error.
Delete these secondary MAC addresses during be_close.
The secondary MAC addresses list will be refreshed during interface open anyway.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently requests the firmware to enable rx_interface options
without considering if the interface was created with that capability.
This could cause commands to firmware to fail.
To avoid this, enable only those options on an interface if the interface
was created with that capability.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is more appropriate to use # of queue pairs currently used by
the driver instead of a magic value.
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver release rtnl lock in between DCB re-configuration.
As a result, other flows (e.g., mtu config) may enter in between and fail
due to halted tx path for dcb configuration.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During VF load, prior to sending messages on HW channel to PF the VF
checks its bulletin board to see whether the PF indicated it has closed;
If a closed PF is encountered, the VF skips sending the message.
Due to incorrect return values, there's a possible scenario in which the VF
finishes loading "successfully", while the PF hasn't actually fully configured
FW/HW for the VFs supposed configuration.
Once VF tries to send Tx packets, HW will raise an attention (and FW possibly
will start treat the VF as malicious).
The patch fails the loading process in such a scenario.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If chip enters a recovery flow just after the driver issues a DMAE request
the DMAE will timeout. Current code will cause a bnx2x_panic() as a result,
which means interface will no longer be usable (regardless of the recovery
results), as bnx2x_panic() is irreversible for the driver.
As this is a possible flow, the panic should be reached only when driver
is compiled with STOP_ON_ERROR.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While unloading, bnx2x needs to clean the sp_rtnl_state to prevent
configuration made before the unload to be applied afterwards with
stale values.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free temporary 'chanspecs' avoiding leakage.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was a bug in xennet_alloc_rx_buffers, when allocating page or
sk_buff failed, and at the same time rx_batch queue not empty,
the rx_refill_timer timer won't be scheduled. If finally the remaining
request buffers in rx ring less than what backend driver expected,
the backend driver would think of rx ring as full and start dropping packets.
In such situation, there is no way for the netfront driver to recover
automatically, so that the device can not work properly.
The patch fixes the problem by always scheduling rx_refill_timer timer when
alloc_page or __netdev_alloc_skb fails, no matter whether rx_batch queue is
empty or not. It ensures that the rx ring request buffers will finally meet
the backend needs.
Signed-off-by: Ma JieYue <jieyue.majy@alibaba-inc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull dmaengine changes from Dan
1/ Bartlomiej and Dan finalized a rework of the dma address unmap
implementation.
2/ In the course of testing 1/ a collection of enhancements to dmatest
fell out. Notably basic performance statistics, and fixed / enhanced
test control through new module parameters 'run', 'wait', 'noverify',
and 'verbose'. Thanks to Andriy and Linus for their review.
3/ Testing the raid related corner cases of 1/ triggered bugs in the
recently added 16-source operation support in the ioatdma driver.
4/ Some minor fixes / cleanups to mv_xor and ioatdma.
Conflicts:
drivers/dma/dmatest.c
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
During resume, use for_each_slave to walk the slaves of the cpsw, and
soft-reset each of them. This prevents oopses if there is only one
slave configured.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I met a Bug when I add ip target with the wrong ip address:
echo +500.500.500.500 > /sys/class/net/bond0/bonding/arp_ip_target
the wrong ip address will transfor to 245.245.245.244 and add
to the ip target success, it is uncorrect, so I add checks to avoid
adding wrong address.
The in4_pton() will set wrong ip address to 0.0.0.0, it will return by
the next check and will not add to ip target.
v2
According Veaceslav's opinion, simplify the code.
v3
According Veaceslav's opinion, add broadcast check and make a micro
definition to package it.
v4
Solve the problem of the format which David point out.
Suggested-by: Veaceslav Falico <vfalico@redhat.com>
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For archs with pages size of 4K, when the chunk is freed, fwp is not in the
list so avoid attempting to delete it.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This driver uses a number of macros to get and set various fields in the
RX and TX descriptors. To work correctly, a u8 pointer to the descriptor
must be used; however, in some cases a descriptor structure pointer is used
instead. In addition, a duplicated statement is removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) After driver load failure, clear 'card->adapter' instead of
card pointer so that card specific cleanup is performed later
when user unloads the driver.
2) Clear usb_card pointer in disconnect handler to avoid invalid
memory access when user unloads the driver after removing the
card.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When driver is failed to load, card pointer doesn't get
freed. We will free it in cleanup handler which is called
in failure as well as unload path.
Also, update drvdata in init/cleanup handlers instead of
register/unregister handlers.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) Currently we freeing wdev for each interface in driver unload
path. We may leak memory if user have already deleted an interface.
mwifiex_add_virtual_intf() allocates wdev structure. So it should
be freed in mwifiex_del_virtual_intf().
This will make sure that wdev will be freed when user deletes an
interface and also in unload path.
2) "priv->netdev->ieee80211_ptr" should also be cleared in
mwifiex_del_virtual_intf.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't need to free/unregister wiphy when
mwifiex_register_cfg80211() fails. The routine internally takes
care of it. This redundant code can cause NULL pointer dereference,
for adapter->wiphy.
Reported-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) If register_netdevice() is failed, we are freeing netdev
pointer, but priv->netdev is not cleared. This gives kernel
paging request error when driver is unloaded or interface is
deleted. Fix the problem by clearing the pointer.
2) Fix memory leak issue by freeing 'wdev' in failure paths.
Also, clear priv->wdev pointer.
As mwifiex_add_virtual_intf() successfully handles the
failure conditions, redundant code under err_add_intf label
is removed in this patch.
Reported-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex_add_virtual_intf() returns ERR_PTR values. So use IS_ERR()
macro instead of checking for NULL pointer.
Reported-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "rt2x00: fix HT TX descriptor settings regression"
assumes that the control parameter to rt2x00mac_tx is always non-NULL.
There is an internal call in rt2x00lib_bc_buffer_iter where NULL is
passed. Fix the resulting crash by adding an initialized dummy on-stack
ieee80211_tx_control struct.
Cc: stable@vger.kernel.org # 3.7+
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On some boards which are based on AR9300, AR9580 or
AR9550, MCS15 usage is problematic.
This is because these boards use a "frequency doubler",
which doubles the refclk to get better EVM, but causes
spurs. Handle this properly in the driver to recover
throughput.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A world regulatory domain check was in place that
prevents user dynamic regulatory hints from being
processed. This was there for historical reasons
as this was only possible previously for world
roaming cards and dynamic regulatory settings was
only possible for country IEs. Fix this by enforcing
the world regulatory domain check only for when the
initiator is a country IE. Support for dynamic user
regulatory support is already checked.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
some robustness fixes for broken virtio devices, plus minor tweaks.
[vs last pull request: added the virtio-scsi broken vq escape patch, which
I somehow lost.]
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=vY2L
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio updates from Rusty Russell:
"Nothing really exciting: some groundwork for changing virtio endian,
and some robustness fixes for broken virtio devices, plus minor
tweaks"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio_scsi: verify if queue is broken after virtqueue_get_buf()
x86, asmlinkage, lguest: Pass in globals into assembler statement
virtio: mmio: fix signature checking for BE guests
virtio_ring: adapt to notify() returning bool
virtio_net: verify if queue is broken after virtqueue_get_buf()
virtio_console: verify if queue is broken after virtqueue_get_buf()
virtio_blk: verify if queue is broken after virtqueue_get_buf()
virtio_ring: add new function virtqueue_is_broken()
virtio_test: verify if virtqueue_kick() succeeded
virtio_net: verify if virtqueue_kick() succeeded
virtio_ring: let virtqueue_{kick()/notify()} return a bool
virtio_ring: change host notification API
virtio_config: remove virtio_config_val
virtio: use size-based config accessors.
virtio_config: introduce size-based accessors.
virtio_ring: plug kmemleak false positive.
virtio: pm: use CONFIG_PM_SLEEP instead of CONFIG_PM
This patch enhances the type safety for the kfifo API. It is now safe
to put const data into a non const FIFO and the API will now generate a
compiler warning when reading from the fifo where the destination
address is pointing to a const variable.
As a side effect the kfifo_put() does now expect the value of an element
instead a pointer to the element. This was suggested Russell King. It
make the handling of the kfifo_put easier since there is no need to
create a helper variable for getting the address of a pointer or to pass
integers of different sizes.
IMHO the API break is okay, since there are currently only six users of
kfifo_put().
The code is also cleaner by kicking out the "if (0)" expressions.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
John W. Linville says:
====================
pull request: wireless 2013-11-14
Please pull this batch of fixes intended for the 3.13 stream!
Amitkumar Karwar offers a quartet of mwifiex fixes, including an
endian fix and three fixes for invalid memory access.
Avinash Patil trims the packet length value for packets received from
an SDIO interface.
Colin Ian King fixes a NULL pointer dereference in the rtlwifi
efuse code.
Dan Carpenter cleans-up an mwifiex integer underflow, a potential
libertas oops, a memory corrupion bug in wcn36xx, and a locking issue
also in wcn36xx.
Dan Williams helps prism54 devices to avoid being misclassified as
Ethernet devices.
Felipe Pena fixes a couple of typo errors, one in rt2x00 and the
other in rtlwifi.
Janusz Dziedzic corrects a pair of DFS-related problems in ath9k.
Larry Finger patches three rtlwifi drivers to correctly report signal
strength even for an unassociated AP.
Mark Cave-Ayland rewrites some endian-illiterate packet type extraction
code in rtlwifi.
Stanislaw Gruszka addresses an rt2x00 regression related to setting
HT station WCID and AMPDU density parameters.
Sujith Manoharan corrects the initvals settings for AR9485.
Ujjal Roy patches an obscure bit of code in mwifiex that was using
the wrong definition of eth_hdr when briding patches in AP mode.
Wei Yongjun fixes a couple of bugs: one is a return code handling
bug in libertas; and, the other is a locking issue in wcn36xx.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2613af0ed1 ("virtio_net: migrate mergeable rx buffers to page
frag allocators") changed the mergeable receive buffer size from PAGE_SIZE
to MTU-size. However, the merge buffer size does not take into account the
size of the virtio-net header. Consequently, packets that are MTU-size
will take two buffers intead of one (to store the virtio-net header),
substantially decreasing the throughput of MTU-size traffic due to TCP
window / SKB truesize effects.
This commit changes the mergeable buffer size to include the virtio-net
header. The buffer size is cacheline-aligned because skb_page_frag_refill
will not automatically align the requested size.
Benchmarks taken from an average of 5 netperf 30-second TCP_STREAM runs
between two QEMU VMs on a single physical machine. Each VM has two VCPUs and
vhost enabled. All VMs and vhost threads run in a single 4 CPU cgroup
cpuset, using cgroups to ensure that other processes in the system will not
be scheduled on the benchmark CPUs. Transmit offloads and mergeable receive
buffers are enabled, but guest_tso4 / guest_csum are explicitly disabled to
force MTU-sized packets on the receiver.
next-net trunk before 2613af0ed1 (PAGE_SIZE buf): 3861.08Gb/s
net-next trunk (MTU 1500- packet uses two buf due to size bug): 4076.62Gb/s
net-next trunk (MTU 1480- packet fits in one buf): 6301.34Gb/s
net-next trunk w/ size fix (MTU 1500 - packet fits in one buf): 6445.44Gb/s
Suggested-by: Eric Northup <digitaleric@google.com>
Signed-off-by: Michael Dalton <mwdalton@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes bug 62491 (https://bugzilla.kernel.org/show_bug.cgi?id=62491).
After resuming some users got the following error flooding the kernel log:
alx 0000:02:00.0: invalid PHY speed/duplex: 0xffff
Signed-off-by: Jonas Hahnfeld <linux@hahnjo.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that genl_ops are no longer modified in place when
registering, they can be made const. This patch was done
mostly with spatch:
@@
identifier ops;
@@
+const
struct genl_ops ops[] = {
...
};
(except the struct thing in net/openvswitch/datapath.c)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver fails to check the results of DMA mapping and results in
the following warning: (with kernel config "CONFIG_DMA_API_DEBUG" enable)
------------[ cut here ]------------
WARNING: at lib/dma-debug.c:937 check_unmap+0x43c/0x7d8()
fec 2188000.ethernet: DMA-API: device driver failed to check map
error[device address=0x00000000383a8040] [size=2048 bytes] [mapped as single]
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.10.17-16827-g9cdb0ba-dirty #188
[<80013c4c>] (unwind_backtrace+0x0/0xf8) from [<80011704>] (show_stack+0x10/0x14)
[<80011704>] (show_stack+0x10/0x14) from [<80025614>] (warn_slowpath_common+0x4c/0x6c)
[<80025614>] (warn_slowpath_common+0x4c/0x6c) from [<800256c8>] (warn_slowpath_fmt+0x30/0x40)
[<800256c8>] (warn_slowpath_fmt+0x30/0x40) from [<8026bfdc>] (check_unmap+0x43c/0x7d8)
[<8026bfdc>] (check_unmap+0x43c/0x7d8) from [<8026c584>] (debug_dma_unmap_page+0x6c/0x78)
[<8026c584>] (debug_dma_unmap_page+0x6c/0x78) from [<8038049c>] (fec_enet_rx_napi+0x254/0x8a8)
[<8038049c>] (fec_enet_rx_napi+0x254/0x8a8) from [<804dc8c0>] (net_rx_action+0x94/0x160)
[<804dc8c0>] (net_rx_action+0x94/0x160) from [<8002c758>] (__do_softirq+0xe8/0x1d0)
[<8002c758>] (__do_softirq+0xe8/0x1d0) from [<8002c8e8>] (do_softirq+0x4c/0x58)
[<8002c8e8>] (do_softirq+0x4c/0x58) from [<8002cb50>] (irq_exit+0x90/0xc8)
[<8002cb50>] (irq_exit+0x90/0xc8) from [<8000ea88>] (handle_IRQ+0x3c/0x94)
[<8000ea88>] (handle_IRQ+0x3c/0x94) from [<8000855c>] (gic_handle_irq+0x28/0x5c)
[<8000855c>] (gic_handle_irq+0x28/0x5c) from [<8000de00>] (__irq_svc+0x40/0x50)
Exception stack(0x815a5f38 to 0x815a5f80)
5f20: 815a5f80 3b9aca00
5f40: 0fe52383 00000002 0dd8950e 00000002 81e7b080 00000000 00000000 815ac4d8
5f60: 806032ec 00000000 00000017 815a5f80 80059028 8041fc4c 60000013 ffffffff
[<8000de00>] (__irq_svc+0x40/0x50) from [<8041fc4c>] (cpuidle_enter_state+0x50/0xf0)
[<8041fc4c>] (cpuidle_enter_state+0x50/0xf0) from [<8041fd94>] (cpuidle_idle_call+0xa8/0x14c)
[<8041fd94>] (cpuidle_idle_call+0xa8/0x14c) from [<8000edac>] (arch_cpu_idle+0x10/0x4c)
[<8000edac>] (arch_cpu_idle+0x10/0x4c) from [<800582f8>] (cpu_startup_entry+0x60/0x130)
[<800582f8>] (cpu_startup_entry+0x60/0x130) from [<80bc7a48>] (start_kernel+0x2d0/0x328)
[<80bc7a48>] (start_kernel+0x2d0/0x328) from [<10008074>] (0x10008074)
---[ end trace c6edec32436e0042 ]---
Because dma-debug add new interfaces to debug dma mapping errors, pls refer
to: http://lwn.net/Articles/516640/
After dma mapping, it must call dma_mapping_error() to check mapping error,
otherwise the map_err_type alway is MAP_ERR_NOT_CHECKED, check_unmap() define
the mapping is not checked and dump the error msg. So,add dma_mapping_error()
checking to fix the WARNING
And RX DMA buffers are used repeatedly and the driver copies it into an skb,
fec_enet_rx() should not map or unmap, use dma_sync_single_for_cpu()/dma_sync_single_for_device()
instead of dma_map_single()/dma_unmap_single().
There have another potential issue: fec_enet_rx() passes the DMA address to __va().
Physical and DMA addresses are *not* the same thing. They may differ if the device
is behind an IOMMU or bounce buffering was required, or just because there is a fixed
offset between the device and host physical addresses. Also fix it in this patch.
=============================================
V2: add net_ratelimit() to limit map err message.
use dma_sync_single_for_cpu() instead of dma_map_single().
fix the issue that pass DMA addresses to __va() to get virture address.
V1: initial send
=============================================
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes two race conditions between bond_store_updelay/downdelay
and bond_store_miimon which could lead to division by zero as miimon can
be set to 0 while either updelay/downdelay are being set and thus miss the
zero check in the beginning, the zero div happens because updelay/downdelay
are stored as new_value / bond->params.miimon. Use rtnl to synchronize with
miimon setting.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hwtstamp_ioctl() should validate all fields of hwtstamp_config
before making any changes. Currently it sets the TX configuration
before validating the rx_filter field.
Untested as I don't have a cross-compiler to hand.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cpsw_hwtstamp_ioctl() should validate all fields of hwtstamp_config,
and the hardware version, before making any changes. Currently it
sets the TX configuration before validating the rx_filter field
or that the hardware supports timestamping.
Also correct the error code for hardware versions that don't
support timestamping. ENOTSUPP is used by the NFS implementation
and is not part of userland API; we want EOPNOTSUPP (which glibc
also calls ENOTSUP, with one 'P').
Untested as I don't have a cross-compiler to hand.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Mugunthan V N <mugunthanvnm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac_hwtstamp_ioctl() should validate all fields of hwtstamp_config
before making any changes. Currently it sets the TX configuration
before validating the rx_filter field.
Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hwtstamp_ioctl() should validate all fields of hwtstamp_config
before making any changes. Currently it sets the TX configuration
before validating the rx_filter field.
Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000e_hwtstamp_ioctl() should validate all fields of hwtstamp_config
before making any changes. Currently it copies the configuration to
the e1000_adapter structure before validating it at all.
Change e1000e_config_hwtstamp() to take a pointer to the
hwstamp_config and to copy the config after validating it.
Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3_hwtstamp_ioctl() should validate all fields of hwtstamp_config
before making any changes. Currently it sets the TX configuration
before validating the rx_filter field.
Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently use hdr_len as a hint of head length which is advertised by
guest. But when guest advertise a very big value, it can lead to an 64K+
allocating of kmalloc() which has a very high possibility of failure when host
memory is fragmented or under heavy stress. The huge hdr_len also reduce the
effect of zerocopy or even disable if a gso skb is linearized in guest.
To solves those issues, this patch introduces an upper limit (PAGE_SIZE) of the
head, which guarantees an order 0 allocation each time.
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently use hdr_len as a hint of head length which is advertised by
guest. But when guest advertise a very big value, it can lead to an 64K+
allocating of kmalloc() which has a very high possibility of failure when host
memory is fragmented or under heavy stress. The huge hdr_len also reduce the
effect of zerocopy or even disable if a gso skb is linearized in guest.
To solves those issues, this patch introduces an upper limit (PAGE_SIZE) of the
head, which guarantees an order 0 allocation each time.
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We assume that "mp->phy" can be NULL a couple lines before the
dereference.
Fixes: 1cce16d37d ('net: mv643xx_eth: Add missing phy_addr_set in DT mode')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is harmless but cdc_ncm_setup() returns negative error codes
truncated to u8 values. There is only one caller and treats all
non-zero returns as errors but doesn't store the the return code. So
the code works correctly but it's messy and upsets the static checkers.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 7b0c5f21f3
"sierra_net: keep status interrupt URB active", sierra_net triggers
status interrupt polling before the net_device is opened (in order to
properly receive the sync message response).
To be able to receive further interrupts, the interrupt urb needs to be
re-submitted, so this patch removes the bogus check for netif_running().
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull core locking changes from Ingo Molnar:
"The biggest changes:
- add lockdep support for seqcount/seqlocks structures, this
unearthed both bugs and required extra annotation.
- move the various kernel locking primitives to the new
kernel/locking/ directory"
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
block: Use u64_stats_init() to initialize seqcounts
locking/lockdep: Mark __lockdep_count_forward_deps() as static
lockdep/proc: Fix lock-time avg computation
locking/doc: Update references to kernel/mutex.c
ipv6: Fix possible ipv6 seqlock deadlock
cpuset: Fix potential deadlock w/ set_mems_allowed
seqcount: Add lockdep functionality to seqcount/seqlock structures
net: Explicitly initialize u64_stats_sync structures for lockdep
locking: Move the percpu-rwsem code to kernel/locking/
locking: Move the lglocks code to kernel/locking/
locking: Move the rwsem code to kernel/locking/
locking: Move the rtmutex code to kernel/locking/
locking: Move the semaphore core to kernel/locking/
locking: Move the spinlock code to kernel/locking/
locking: Move the lockdep code to kernel/locking/
locking: Move the mutex code to kernel/locking/
hung_task debugging: Add tracepoint to report the hang
x86/locking/kconfig: Update paravirt spinlock Kconfig description
lockstat: Report avg wait and hold times
lockdep, x86/alternatives: Drop ancient lockdep fixup message
...
Currently the ARP monitoring is not supported with 802.3ad, and it's
prohibited to use it via the module params.
However we still can set it afterwards via sysfs, cause we only check for
*LB modes there.
To fix this - add a check for 802.3ad mode in bonding_store_arp_interval.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull DMA mask updates from Russell King:
"This series cleans up the handling of DMA masks in a lot of drivers,
fixing some bugs as we go.
Some of the more serious errors include:
- drivers which only set their coherent DMA mask if the attempt to
set the streaming mask fails.
- drivers which test for a NULL dma mask pointer, and then set the
dma mask pointer to a location in their module .data section -
which will cause problems if the module is reloaded.
To counter these, I have introduced two helper functions:
- dma_set_mask_and_coherent() takes care of setting both the
streaming and coherent masks at the same time, with the correct
error handling as specified by the API.
- dma_coerce_mask_and_coherent() which resolves the problem of
drivers forcefully setting DMA masks. This is more a marker for
future work to further clean these locations up - the code which
creates the devices really should be initialising these, but to fix
that in one go along with this change could potentially be very
disruptive.
The last thing this series does is prise away some of Linux's addition
to "DMA addresses are physical addresses and RAM always starts at
zero". We have ARM LPAE systems where all system memory is above 4GB
physical, hence having DMA masks interpreted by (eg) the block layers
as describing physical addresses in the range 0..DMAMASK fails on
these platforms. Santosh Shilimkar addresses this in this series; the
patches were copied to the appropriate people multiple times but were
ignored.
Fixing this also gets rid of some ARM weirdness in the setup of the
max*pfn variables, and brings ARM into line with every other Linux
architecture as far as those go"
* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
ARM: DMA-API: better handing of DMA masks for coherent allocations
ARM: 7857/1: dma: imx-sdma: setup dma mask
DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
DMA-API: dcdbas: update DMA mask handing
DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
DMA-API: crypto: remove last references to 'static struct device *dev'
DMA-API: crypto: fix ixp4xx crypto platform device support
DMA-API: others: use dma_set_coherent_mask()
DMA-API: staging: use dma_set_coherent_mask()
DMA-API: usb: use new dma_coerce_mask_and_coherent()
DMA-API: usb: use dma_set_coherent_mask()
DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
...
