Driver is using "qcom,emu-init-seq" for finding length of property
but using "qcom,qemu-init-seq" instead of "qcom,emu-init-seq" to
get passed values from device tree. With this, length of property
comes as expected but values are not received. This results into
programming zeros as values with offset as zero instead of expected
<value, offset> passed through devicetree.
CRs-Fixed: 1051115
Change-Id: I1809fcef844d275175814e636591b87e91432609
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Add the QDSS STM property to the device tree so
that data can be logged from the GPU to the debug
bus when available.
CRs-Fixed: 1031648
Change-Id: I754c85a2ed02d0b1e40fd1e27b10ff84c463ac83
Signed-off-by: Jonathan Wicks <jwicks@codeaurora.org>
Update TLMM base address to match new address.
Change-Id: Ie0c46cbbcbc3edabd5e0f867b4393a27e55db9f5
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Update TLMM configuration for msmfalcon, to match new
HW definitions.
Change-Id: I61d99454dab2fa90b4ed6577d1a58685088eb968
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Add SDC1 related pin configuration and update addresses for
SDC2 pins, to match TLMM addresses in new HW definitions.
Change-Id: If39ad62cc591565793cd1d8a0f2a454e0b7d5c58
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Modified condition to ensure data is read
only after interrupt has occurred.
Spurious interrupt handling is done in nfc_read
instead of irq handler.
Change-Id: Ie2362610fe922e792e6358b4386c828fdd754fa8
Signed-off-by: Gaurav Singhal <gsinghal@codeaurora.org>
Decoder YUV buffer size should be derived based on current
resolution using Venus MACROS. This the only size that
clients are aware of. Using the size from FW will make
buffer sizes mismatches and unnecessary failures.
By not using buffer size from Venus, driver can avoid
unnecessary buffer requirement calls. This will reduce the
start-up latency.
CRs-Fixed: 1011881
Change-Id: I90762967e8b7888a775ce4771b6cdb08528b6513
Signed-off-by: Vikash Garodia <vgarodia@codeaurora.org>
Signed-off-by: Praneeth Paladugu <ppaladug@codeaurora.org>
FM audio playback is failing as the loopback mode
is hardcoded to EC mode which is incorrect for
FM audio playback usecase.
Change it to default loopback mode.
Change-Id: I36b60ba2283b0bbe36f492e1410603b8c2050cc4
Signed-off-by: Shiv Maliyappanahalli <smaliyap@codeaurora.org>
During playback, enabling smart boost feature changes the threshold
of the playback signal based on the amplitude of the signal without
clipping the signal. Change enables smart boost on WCD9340 codec.
Change-Id: Ic4c5e3cc071898f376070b853112c5014d61272c
Signed-off-by: Sudheer Papothi <spapothi@codeaurora.org>
Integer overflow check always fails when ULONG_MAX is used,
as ULONG_MAX is 2^64-1, while req->data[i].len and total
are uint32_t. Make change to use U32_MAX instead of
ULONG_MAX.
CRs-fixed: 1046507
Change-Id: Iccf9c32400ecc7ffc0afae16f58c38e5d78a5b64
Signed-off-by: Zhen Kong <zkong@codeaurora.org>
DMIC clock on ECPP(Echo Cancellation Ping-Pong) hardware path
can run at lower clock rate to avoid power consumption. Select
ECPP dmic clock rate when decimator is connected only to ECPP
path.
CRs-fixed: 1022917
Change-Id: I968e1fe6b099ebf5334eadb209219181293b207f
Signed-off-by: Sudheer Papothi <spapothi@codeaurora.org>
Signed-off-by: Vidyakumar Athota <vathota@codeaurora.org>
DMIC clock on ECPP(Echo Cancellation Ping-Pong) path can be set to
lower clock rate to avoid power consumption. Change configures the
DMIC clock rate on ECPP path based on device tree settings.
CRs-fixed: 1022917
Change-Id: I03e1a7f5ef3cf1b1907c03a3d38965ce3a611bc4
Signed-off-by: Sudheer Papothi <spapothi@codeaurora.org>
Signed-off-by: Vidyakumar Athota <vathota@codeaurora.org>
WCD9335 codec has single master clock supply widget for both
playback and recording paths. Adding separate clock supply
for playback and recording paths will help handle low power
audio recording usecases without affecting playback usecases.
Change is to enable separate clock supply widgets for playback
and recording paths.
CRs-fixed: 1022917
Change-Id: I3978d2c53f2b04104d9d279f8acad60326f9405c
Signed-off-by: Sudheer Papothi <spapothi@codeaurora.org>
Signed-off-by: Vidyakumar Athota <vathota@codeaurora.org>
Export API for getting SOC serial number so that other modules
can use it.
CRs-Fixed: 1050491
Change-Id: I24f735159a38dffdc4f44babacc4d758cd0a8365
Signed-off-by: Yuanyuan Liu <yuanliu@codeaurora.org>
Enable G-Link SPI Transport driver to enable off-chip communication
over SPI bus.
CRs-Fixed: 1045916
Change-Id: I268d96f04b034edad2fadea8ef2c14fe8d8de251
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
G-Link SPI Transport is used to communicate with external audio codec.
Add G-Link SPI Transport device to support that configuration.
CRs-Fixed: 1045916
Change-Id: I97ca857c21d8873574a180d289e2fbca29c8a891
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
GLink SPI Transport enables point-to-point communication with an
external subsystem that uses SPI bus to interface. This enables
multiplexing multiple logical channels over the SPI bus.
CRs-Fixed: 1045916
Change-Id: I1936bb0542bcd531726bf987ef806969ce96d498
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Array overflow can occur in firmware_name_store(), if the variable
buf contains the string larger than size of subsys->desc->fw_name
CRs-Fixed: 1050153
Change-Id: Ice39d7a1eb0b5f53125cc5d528021a99b9f7ff90
Signed-off-by: Srinivasarao P <spathi@codeaurora.org>
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
