This patch corrects addresses of acceptance filters. These registers are not in
use, but values should be correct. Tested with MCP2515 and am3352 and also
checked datasheets for MCP2515 and MCP2510.
Signed-off-by: Tomas Krcka <tomas.krcka@nkgroup.cz>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Passive DP->DVI/HDMI dongles on DP++ ports show up to the system as HDMI
devices, as they do not have a sink device in them to respond to any AUX
traffic. When probing these dongles over the DDC, sometimes they will
NAK the first attempt even though the transaction is valid and they
support the DDC protocol. The retry loop inside of
drm_do_probe_ddc_edid() would normally catch this case and try the
transaction again, resulting in success.
That, however, was thwarted by the fix for [1]:
commit 9292f37e1f
Author: Eugeni Dodonov <eugeni.dodonov@intel.com>
Date: Thu Jan 5 09:34:28 2012 -0200
drm: give up on edid retries when i2c bus is not responding
This added code to exit immediately if the return code from the
i2c_transfer function was -ENXIO in order to reduce the amount of time
spent in waiting for unresponsive or disconnected devices. That was
possible because the underlying i2c bit banging algorithm had retries of
its own (which, of course, were part of the reason for the bug the
commit fixes).
Since its introduction in
commit f899fc64cd
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Jul 20 15:44:45 2010 -0700
drm/i915: use GMBUS to manage i2c links
we've been flipping back and forth enabling the GMBUS transfers, but
we've settled since then. The GMBUS implementation does not do any
retries, however, bailing out of the drm_do_probe_ddc_edid() retry loop
on first encounter of -ENXIO. This, combined with Eugeni's commit, broke
the retry on -ENXIO.
Retry GMBUS once on -ENXIO on first message to mitigate the issues with
passive adapters.
This patch is based on the work, and commit message, by Todd Previte
<tprevite@gmail.com>.
[1] https://bugs.freedesktop.org/show_bug.cgi?id=41059
v2: Don't retry if using bit banging.
v3: Move retry within gmbux_xfer, retry only on first message.
v4: Initialize GMBUS0 on retry (Ville).
v5: Take index reads into account (Ville).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85924
Cc: Todd Previte <tprevite@gmail.com>
Cc: stable@vger.kernel.org
Tested-by: Oliver Grafe <oliver.grafe@ge.com> (v2)
Tested-by: Jim Bride <jim.bride@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Pull networking fixes from David Miller:
1) Fix stack allocation in s390 BPF JIT, from Michael Holzheu.
2) Disable LRO on openvswitch paths, from Jiri Benc.
3) UDP early demux doesn't handle multicast group membership properly,
fix from Shawn Bohrer.
4) Fix TX queue hang due to incorrect handling of mixed sized fragments
and linearlization in i40e driver, from Anjali Singhai Jain.
5) Cannot use disable_irq() in timer handler of AMD xgbe driver, from
Thomas Lendacky.
6) b2net driver improperly assumes pci_alloc_consistent() gives zero'd
out memory, use dma_zalloc_coherent(). From Sriharsha Basavapatna.
7) Fix use-after-free in MPLS and ipv6, from Robert Shearman.
8) Missing neif_napi_del() calls in cleanup paths of b44 driver, from
Hauke Mehrtens.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: replace last open coded skb_orphan_frags with function call
net: bcmgenet: power on MII block for all MII modes
ipv6: Fix protocol resubmission
ipv6: fix possible use after free of dev stats
b44: call netif_napi_del()
bridge: disable softirqs around br_fdb_update to avoid lockup
Revert "bridge: use _bh spinlock variant for br_fdb_update to avoid lockup"
mpls: fix possible use after free of device
be2net: Replace dma/pci_alloc_coherent() calls with dma_zalloc_coherent()
bridge: use _bh spinlock variant for br_fdb_update to avoid lockup
amd-xgbe: Use disable_irq_nosync from within timer function
rhashtable: add missing import <linux/export.h>
i40e: Make sure to be in VEB mode if SRIOV is enabled at probe
i40e: start up in VEPA mode by default
i40e/i40evf: Fix mixed size frags and linearization
ipv4/udp: Verify multicast group is ours in upd_v4_early_demux()
openvswitch: disable LRO
s390/bpf: fix bpf frame pointer setup
s390/bpf: fix stack allocation
This fixes a minor issue affecting multiqueue virtio net
when user keeps changing the number of active queues
and CPUs are added and removed by hotplug.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVdgTnAAoJECgfDbjSjVRpP0IIAKfJaaxXKJEzHQ8k/8w8MNI3
xqyDV53kvWWHgwLTw1IxrLs0J2hkwdCnEnuRbwEm5XT9n2MoZDh3hC5A9gDN9NkW
rGDL2zX63gsdNyv5cxeXHWPLaph1NAL1Ausf0SEwLm7mTPbd6wJETITpdlV3dhLF
00NrlrF+0O3SlWHX7eVHWC1sI4Uc7BNXMuj4TZ0xv64xbuoTCsJeaij2t/ptqpwS
ao8trxbL3OcAY7wxeVsDz6sjkKE4+qlpgfXC8nw8+waFPrH3xfylo123qyeRWm3b
qqLxmCq2J0s3LUBCgvn4lKJdHGZEKtrUGbQ+qhYBrvCcMC+sOrbOv9kS3JwTC+E=
=zOjK
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull last-minute virtio fix from Michael Tsirkin:
"This fixes a minor issue affecting multiqueue virtio net when user
keeps changing the number of active queues and CPUs are added and
removed by hotplug"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_pci: Clear stale cpumask when setting irq affinity
Vendor commands are passed from userspace through the
NFC_CMD_VENDOR netlink command, allowing driver and hardware
specific operations implementations like for example RF tuning
or production line calibration.
Drivers will associate a set of vendor commands to a vendor
id, which could typically be an OUI. The netlink kernel
implementation will try to match the received vendor id
and sub command attributes with the registered ones. When
such match is found, the driver defined sub command routine
is called.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Together with inline routines to associate a vendor commands
array with an NFC device.
Vendor commands allow vendors to implement their very specific
operations from driver code instead of adding new stack ops
for non NFC generic commands.
Vendors need to select their own unique IDs and use that as a
namespace for defining sub commands.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fix the device tree entries to modify the '_' to '-'.
Also changes the names of the internal delay properties
from -int- to -internal- as the -int- appeared as a keyword.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
API compliance scanning with coccinelle flagged:
./drivers/atm/iphase.c:2621:4-20:
WARNING: timeout (50) seems HZ dependent
Numeric constants passed to schedule_timeout() make the effective
timeout HZ dependent which does not seem intended.
Fixed up by converting the constant to jiffies with msecs_to_jiffies()
As this driver was introduced in the early 2.3 series it is most
likely assuming HZ=100 so the constant 50 is converted to 500ms.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to prevent any NFC feature when NFC is disable and
to save power, (down to 4uA) put the CLF in hibernate mode
with RF deactivated.
Add the equivalent to enable the NFC feature when initiating
the st21nfcb driver.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When st21nfcb is disabled, the irq line may remain active
while no data are available, flooding the system with
irrelevant i2c transaction.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The powered flag can be set from the ndlc_open and ndlc_close layer.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Removing st21nfcb may need to execute some specific commands before
stopping the ndlc state machine.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When closing the device some data (proprietary commands)
might be sent. The core state machine needs to be set for
correct command execution.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
On st21nfcb, nci proprietary commands are available to run
specific chip operations (for example: power management)
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When closing st21nfcb driver, flag ST21NFCB_NCI_RUNNING can be cleared
only once the ndlc and the transport (i2c or spi) layers are released.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to release the st21nfcb properly close the ndlc
layer first.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
ndlc_remove already calls st21nfcb_nci_i2c_disable and
phy->powered is already set to 0.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Once the data is sent, we need to preserve the full frame for
the ndlc state machine. If the NDLC ACK is not received in time,
the ndlc layer will resend the same frame.
Having the header byte pulled will corrupt the frame.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since ndev->driver_data is allocated by devm_kzalloc(), we do not
need the inappropriate kfree to free it in driver's remove function.
Freeing will trigger when driver unloads.
Cc: stable@vger.kernel.org
Acked-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Firo Yang <firogm@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Handle allowing to send proprietary nci commands anywhere in the nci
state machine.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some device may need to execute some proprietary commands
in order to "wake-up"; Before the nci state initialization.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
setup was executed in any case, even if NCI_RESET failed.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Allow for drivers to explicitly define handlers for each
proprietary notifications and responses they expect to support.
Reviewed-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Several of these goto exit; uses should be direct returns
as skb is not yet initialized by nci_hci_get_param().
Miscellanea:
o Use !memcmp instead of memcmp() == 0
o Remove unnecessary goto from if () {... goto exit;} else {...} exit:
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*()
functions) which appeared in v3.17-rc1, the gpiod_get* functions
take an additional parameter that allows to specify direction and
initial value for output.
Use this to simplify the driver. Furthermore this is one caller less
that stops us making the flags argument to gpiod_get*() mandatory.
While touching this also do some minor coding style fixes.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In microread_i2c_irq_thread_fn 'client' set but not used
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
CONFIG_DYNAMIC_DEBUG is the right toggle to enable pr_debug().
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The current versions of the trf7970a has an erratum where it returns
an extra byte in the response to 'Read Multiple Block' (RMB) commands.
This command is issued to Type 5 tags (i.e., ISO/IEC 15693 tags) by
the neard daemon.
To handle this, define a new Device Tree property,
't5t-rmb-extra-byte-quirk', which indicates that the associated
trf7970a device has this erratum. The trf7970a device driver
will then ensure that the response length to RMB commands is
reduced by one byte (for devices with the erratum).
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When GPIO is not enabled we hit this kind of warning:
drivers/nfc/nxp-nci/i2c.c: In function 'nxp_nci_i2c_acpi_config':
drivers/nfc/nxp-nci/i2c.c:320:2: error: implicit declaration of function 'devm_gpiod_get_index' [-Werror=implicit-function-declaration]
gpiod_en = devm_gpiod_get_index(&client->dev, NULL, 2);
This is fixed by explicitely including gpio/consumer.h.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
About 10 days worth of small bug fixes, and the (hopefully) final
round fixes for from arm-soc land for the -rc cycle. Nothing special
to note, but here's a brief summary of fixes by SoC type:
- OMAP: small set of misc. DT fixes; boot fix for THUMB2 kernel
- mediatek: PMIC fixes; DT fix for model name
- exynos: wakeup interupt fixes for 3250
- mvebu: revert mbus patch which broke DMA masters
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gSjy
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Kevin Hilman:
"About 10 days worth of small bug fixes, and the (hopefully) final
round fixes for from arm-soc land for the -rc cycle. Nothing special
to note, but here's a brief summary of fixes by SoC type:
- OMAP:
small set of misc DT fixes; boot fix for THUMB2 kernel
- mediatek:
PMIC fixes; DT fix for model name
- exynos:
wakeup interupt fixes for 3250
- mvebu:
revert mbus patch which broke DMA masters
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: am335x-boneblack: disable RTC-only sleep to avoid hardware damage
ARM: dts: AM35xx: fix system control module clocks
arm64: dts: mt8173-evb: fix model name
ARM: exynos: Fix wake-up interrupts for Exynos3250
ARM: dts: Fix n900 dts file to work around 4.1 touchscreen regression on n900
ARM: dts: Fix dm816x to use right compatible flag for MUSB
ARM: OMAP3: Fix booting with thumb2 kernel
Revert "bus: mvebu-mbus: make sure SDRAM CS for DMA don't overlap the MBus bridge window"
bus: mvebu-mbus: do not set WIN_CTRL_SYNCBARRIER on non io-coherent platforms.
ARM: mvebu: armada-xp-linksys-mamba: Disable internal RTC
soc: mediatek: Add compile dependency to pmic-wrapper
soc: mediatek: PMIC wrap: Fix register state machine handling
soc: mediatek: PMIC wrap: Fix clock rate handling
Update the AFE_TX_CONFIG value to solve marginal rise/fall issues
observed when the link is operating in 100BaseT. This workaround applies
to GPHY revisions D0, E0 and newer.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 70008aa50e ("skbuff: convert to skb_orphan_frags") replaced
open coded tests of SKBTX_DEV_ZEROCOPY and skb_copy_ubufs with calls
to helper function skb_orphan_frags. Apply that to the last remaining
open coded site.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RGMII block is currently only powered on when using RGMII or
RGMII_NO_ID, which is not correct when using the GENET interface in MII
or Reverse MII modes. We always need to power on the RGMII interface for
this block to properly work, regardless of the MII mode in which we
operate.
Fixes: aa09677cba ("net: bcmgenet: add MDIO routines")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP encapsulation is broken on IPv6. This is because the logic to resubmit
the nexthdr is inverted, checking for a ret value > 0 instead of < 0. Also,
the resubmit label is in the wrong position since we already get the
nexthdr value when performing decapsulation. In addition the skb pull is no
longer necessary either.
This changes the return value check to look for < 0, using it for the
nexthdr on the next iteration, and moves the resubmit label to the proper
location.
With these changes the v6 code now matches what we do in the v4 ip input
code wrt resubmitting when decapsulating.
Signed-off-by: Josh Hunt <johunt@akamai.com>
Acked-by: "Tom Herbert" <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The memory pointed to by idev->stats.icmpv6msgdev,
idev->stats.icmpv6dev and idev->stats.ipv6 can each be used in an RCU
read context without taking a reference on idev. For example, through
IP6_*_STATS_* calls in ip6_rcv. These memory blocks are freed without
waiting for an RCU grace period to elapse. This could lead to the
memory being written to after it has been freed.
Fix this by using call_rcu to free the memory used for stats, as well
as idev after an RCU grace period has elapsed.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
breakage on BeagleBones:
- BeagleBones don't support RTC-only mode, it can cause hardware
damage if system-power-controller is specified without
ti,pmic-shutdown-controller
- Fix a recent regression to am3517 SoCs caused by the recent clock
move that was not noticed until now despite automated boot
testing
- Fix a regression for n900 touchscreen triggered by recent
recent input changes
- Fix compatible property for dm816x USB to avoid errors with
USB Ethernet
- Fix oops for omap3 when built with CONFIG_THUMB2_KERNEL
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVbLwXAAoJEBvUPslcq6VzGnoQANbB1fMm74/aMuyVW4LoErio
ii83kk2pX8EWbePle0rUrrre55LzRhJRr2Mcj4bSniafNqkYr36dQrxErnqwmBtA
XawjoVPQB3mG/tBD0oVkzmJtaAXW3GA8IkmQrVe4jUqCh7AjnHYZ5IYjFtGxbJey
oyHI48jcxQE1hhNfeTwHOlLhIIPGpRfdE8vYWOlM+rvm/7ZmKCNmnfZzx0XAyLjq
rXw3IEgyIMbrbHy8fvdE/t2paWV+kb7urVzS/eu7Zn60CpZ9gwWFz4uENvvN2mDk
L78Jz6uxxNrSmGCY+A1LBNWdt7KgiK1GqX/NkI9yc3vvkaJ/aYUh/1zae3pcofpY
HNPcGWNAszDpP1xxCvwhNdJWaKWytZbHadTuVcyU86bKnEiu8Ph3Nh//EizNk/fK
gpSEzRNPP8oVKY3iUIwtG8CfeiKZHI3EjyYTYM+Z9wg0OMpospX4A6VAiyUpuNO+
DeuAMGC46OhxOperErl4R+qomx2nf7d2FLvJnes/cp5sxM97Qeu7XYqzoqKVyJyU
uLKNKmRS71Q1yddQKBVT5nCh5lTw/Mm+qCTHmeelRj52HbtxoT44EzdOr/OhY/0z
td07Y+B1SANLrq5r/tBPBrYc0imJPKzD9Woyab7PASE0KxhNqkyAG0zA/9b/zLYo
cqnk7D22Hs5ZOm4LyY3Q
=Saui
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.1/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge omap fixes for v4.1, urgent fix to avoid potential hardware damage From Tony Lindgren:
Omap fixes for the -rc cycle, including a fix for potential hardware
breakage on BeagleBones:
- BeagleBones don't support RTC-only mode, it can cause hardware
damage if system-power-controller is specified without
ti,pmic-shutdown-controller
- Fix a recent regression to am3517 SoCs caused by the recent clock
move that was not noticed until now despite automated boot
testing
- Fix a regression for n900 touchscreen triggered by recent
recent input changes
- Fix compatible property for dm816x USB to avoid errors with
USB Ethernet
- Fix oops for omap3 when built with CONFIG_THUMB2_KERNEL
* tag 'omap-for-v4.1/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-boneblack: disable RTC-only sleep to avoid hardware damage
ARM: dts: AM35xx: fix system control module clocks
ARM: dts: Fix n900 dts file to work around 4.1 touchscreen regression on n900
ARM: dts: Fix dm816x to use right compatible flag for MUSB
ARM: OMAP3: Fix booting with thumb2 kernel
Pull Intel IOMMU fix from David Woodhouse:
"This fixes an oops when attempting to enable 1:1 passthrough mode for
devices on which VT-d translation was disabled anyway.
It's actually a long-standing bug but recent changes (commit
18436afdc1: "iommu/vt-d: Allow RMRR on graphics devices too") have
made it much easier to trigger with 'iommu=pt intel_iommu=igfx_off' on
the command line"
* git://git.infradead.org/intel-iommu:
iommu/vt-d: Fix passthrough mode with translation-disabled devices
Pull libata fixes from Tejun Heo:
"Two driver fixes. One is for an ahci_mvebu controller config bug and
the other fixes pata_octeon_cf build issue"
* 'for-4.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
pata_octeon_cf: fix broken build
ata: ahci_mvebu: Fix wrongly set base address for the MBus window setting
In the commit below, I missed the connector allocation in the function
intel_sdvo_analog_init(), leading to those connectors to have a NULL
state pointer.
commit 08d9bc920d
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Fri Apr 10 10:59:10 2015 +0300
drm/i915: Allocate connector state together with the connectors
Reported-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
MODULE_DEVICE_TABLE is referring to wrong driver's table and breaks the
build. Fix that.
Cc: stable@vger.kernel.org
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Jaeden Amero says:
====================
net/phy: micrel: Center FLP timing at 16ms
In v2, we add an additional cleanup commit to make an array of strings
static const and to improve const correctness generally. We also no longer
unnecessarily initialize the result variable in
ksz9031_center_flp_timing().
In v3, we remove the unnecessary result variable from ksz9031_config_init()
introduced by a previous version of "net/phy: micrel: Center FLP timing at
16ms".
In v4, we modify the commit message of "net/phy: micrel: Center FLP timing
at 16ms" to replace the awkward quotation of the data sheet's programming
procedure with an explanation of why we program the FLP burst registers and
restart auto-negotiation where we do (config_init).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Link failures have been observed when using the KSZ9031 with HP 1810-8G
and HP 1910-8G network switches. Center the FLP timing at 16ms to help
avoid intermittent link failures.
>From the KSZ9031RNX and KSZ9031MNX data sheets revision 2.2, section
"Auto-Negotiation Timing":
The KSZ9031[RNX or MNX] Fast Link Pulse (FLP) burst-to-burst
transmit timing for Auto-Negotiation defaults to 8ms. IEEE 802.3
Standard specifies this timing to be 16ms +/-8ms. Some PHY link
partners need to receive the FLP with 16ms centered timing;
otherwise, there can be intermittent link failures and long
link-up times.
The PHY data sheet recommends configuring the FLP burst registers after
power-up/reset and immediately thereafter restarting auto-negotiation, so
we center the FLP timing at 16ms and then restart auto-negotiation in the
config_init for KSZ9031.
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some defines for a few pad skew related extended registers.
Specify for which MMD Address (dev_addr) they are for.
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a few places in this driver, we weren't using const where we could
have. Use const more.
In addition, change the arrays of strings in ksz9031_config_init() to be
not only const, but also static.
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Alexander Duyck pointed out that:
struct tnode {
...
struct key_vector kv[1];
}
The kv[1] member of struct tnode is an arry that refernced by
a null pointer will not crash the system, like this:
struct tnode *p = NULL;
struct key_vector *kv = p->kv;
As such p->kv doesn't actually dereference anything, it is simply a
means for getting the offset to the array from the pointer p.
This patch make the code more regular to avoid making people feel
odd when they look at the code.
Signed-off-by: Firo Yang <firogm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
API compliance scanning with coccinelle flagged:
./drivers/net/wan/dscc4.c:1036:1-33:
WARNING: timeout (10) seems HZ dependent
./drivers/net/wan/dscc4.c:554:2-34:
WARNING: timeout (10) seems HZ dependent
./drivers/net/wan/dscc4.c:599:2-34:
WARNING: timeout (10) seems HZ dependent
Numeric constants passed to schedule_timeout_*() make the effective
timeout HZ dependent which does not seem to be the intent here.
Fixed up by converting the constant to jiffies with msecs_to_jiffies(),
passing 100ms (assuming HZ==100 in the original code).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
