icsk_rto is a 32bit field, and icsk_backoff can reach 15 by default,
or more if some sysctl (eg tcp_retries2) are changed.
Better use 64bit to perform icsk_rto << icsk_backoff operations
As Joe Perches suggested, add a helper for this.
Yuchung spotted the tcp_v4_err() case.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC2710 (MLDv1), section 3.7. says:
The length of a received MLD message is computed by taking the
IPv6 Payload Length value and subtracting the length of any IPv6
extension headers present between the IPv6 header and the MLD
message. If that length is greater than 24 octets, that indicates
that there are other fields present *beyond* the fields described
above, perhaps belonging to a *future backwards-compatible* version
of MLD. An implementation of the version of MLD specified in this
document *MUST NOT* send an MLD message longer than 24 octets and
MUST ignore anything past the first 24 octets of a received MLD
message.
RFC3810 (MLDv2), section 8.2.1. states for *listeners* regarding
presence of MLDv1 routers:
In order to be compatible with MLDv1 routers, MLDv2 hosts MUST
operate in version 1 compatibility mode. [...] When Host
Compatibility Mode is MLDv2, a host acts using the MLDv2 protocol
on that interface. When Host Compatibility Mode is MLDv1, a host
acts in MLDv1 compatibility mode, using *only* the MLDv1 protocol,
on that interface. [...]
While section 8.3.1. specifies *router* behaviour regarding presence
of MLDv1 routers:
MLDv2 routers may be placed on a network where there is at least
one MLDv1 router. The following requirements apply:
If an MLDv1 router is present on the link, the Querier MUST use
the *lowest* version of MLD present on the network. This must be
administratively assured. Routers that desire to be compatible
with MLDv1 MUST have a configuration option to act in MLDv1 mode;
if an MLDv1 router is present on the link, the system administrator
must explicitly configure all MLDv2 routers to act in MLDv1 mode.
When in MLDv1 mode, the Querier MUST send periodic General Queries
truncated at the Multicast Address field (i.e., 24 bytes long),
and SHOULD also warn about receiving an MLDv2 Query (such warnings
must be rate-limited). The Querier MUST also fill in the Maximum
Response Delay in the Maximum Response Code field, i.e., the
exponential algorithm described in section 5.1.3. is not used. [...]
That means that we should not get queries from different versions of
MLD. When there's a MLDv1 router present, MLDv2 enforces truncation
and MRC == MRD (both fields are overlapping within the 24 octet range).
Section 8.3.2. specifies behaviour in the presence of MLDv1 multicast
address *listeners*:
MLDv2 routers may be placed on a network where there are hosts
that have not yet been upgraded to MLDv2. In order to be compatible
with MLDv1 hosts, MLDv2 routers MUST operate in version 1 compatibility
mode. MLDv2 routers keep a compatibility mode per multicast address
record. The compatibility mode of a multicast address is determined
from the Multicast Address Compatibility Mode variable, which can be
in one of the two following states: MLDv1 or MLDv2.
The Multicast Address Compatibility Mode of a multicast address
record is set to MLDv1 whenever an MLDv1 Multicast Listener Report is
*received* for that multicast address. At the same time, the Older
Version Host Present timer for the multicast address is set to Older
Version Host Present Timeout seconds. The timer is re-set whenever a
new MLDv1 Report is received for that multicast address. If the Older
Version Host Present timer expires, the router switches back to
Multicast Address Compatibility Mode of MLDv2 for that multicast
address. [...]
That means, what can happen is the following scenario, that hosts can
act in MLDv1 compatibility mode when they previously have received an
MLDv1 query (or, simply operate in MLDv1 mode-only); and at the same
time, an MLDv2 router could start up and transmits MLDv2 startup query
messages while being unaware of the current operational mode.
Given RFC2710, section 3.7 we would need to answer to that with an MLDv1
listener report, so that the router according to RFC3810, section 8.3.2.
would receive that and internally switch to MLDv1 compatibility as well.
Right now, I believe since the initial implementation of MLDv2, Linux
hosts would just silently drop such MLDv2 queries instead of replying
with an MLDv1 listener report, which would prevent a MLDv2 router going
into fallback mode (until it receives other MLDv1 queries).
Since the mapping of MRC to MRD in exactly such cases can make use of
the exponential algorithm from 5.1.3, we cannot [strictly speaking] be
aware in MLDv1 of the encoding in MRC, it seems also not mentioned by
the RFC. Since encodings are the same up to 32767, assume in such a
situation this value as a hard upper limit we would clamp. We have asked
one of the RFC authors on that regard, and he mentioned that there seem
not to be any implementations that make use of that exponential algorithm
on startup messages. In any case, this patch fixes this MLD
interoperability issue.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clock is disabled when the device is blocked.
So, clock_enabled is the logical negation of "blocked".
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changes to the cls_u32 classifier must appear atomic to the
readers. Before this patch if a change is requested for both
the exts and ifindex, first the ifindex is updated then the
exts with tcf_exts_change(). This opens a small window where
a reader can have a exts chain with an incorrect ifindex. This
violates the the RCU semantics.
Here we resolve this by always passing u32_set_parms() a copy
of the tc_u_knode to work on and then inserting it into the hash
table after the updates have been successfully applied.
Tested with the following short script:
#tc filter add dev p3p2 parent 8001:0 protocol ip prio 99 handle 1: \
u32 divisor 256
#tc filter add dev p3p2 parent 8001:0 protocol ip prio 99 \
u32 link 1: hashkey mask ffffff00 at 12 \
match ip src 192.168.8.0/2
#tc filter add dev p3p2 parent 8001:0 protocol ip prio 102 \
handle 1::10 u32 classid 1:2 ht 1: \
match ip src 192.168.8.0/8 match ip tos 0x0a 1e
#tc filter change dev p3p2 parent 8001:0 protocol ip prio 102 \
handle 1::10 u32 classid 1:2 ht 1: \
match ip src 1.1.0.0/8 match ip tos 0x0b 1e
CC: Eric Dumazet <edumazet@google.com>
CC: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a missed free_percpu in the unwind code path and when
keys are destroyed.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unable to load various tunneling modules without this:
[ 80.679049] fou: Unknown symbol udp_sock_create6 (err 0)
[ 91.439939] ip6_udp_tunnel: Unknown symbol ip6_local_out (err 0)
[ 91.439954] ip6_udp_tunnel: Unknown symbol __put_net (err 0)
[ 91.457792] vxlan: Unknown symbol udp_sock_create6 (err 0)
[ 91.457831] vxlan: Unknown symbol udp_tunnel6_xmit_skb (err 0)
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ce93718fb7 ("net: Don't keep
around original SKB when we software segment GSO frames") frees the
original skb after software GSO even for dodgy gso skbs. This breaks
the stream throughput from untrusted sources, since only header
checking was done during software GSO instead of a true
segmentation. This patch fixes this by freeing the original gso skb
only when it was really segmented by software.
Fixes ce93718fb7 ("net: Don't keep
around original SKB when we software segment GSO frames.")
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow switch drivers to implement per-port Wake-on-LAN getter and
setters.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an abstraction layer to suspend/resume switch devices, doing the
following split:
- suspend/resume the slave network devices and their corresponding PHY
devices
- suspend/resume the switch hardware using switch driver callbacks
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We cannot make struct qdisc_skb_cb bigger without impacting IPoIB,
or increasing skb->cb[] size.
Commit e0f31d8498 ("flow_keys: Record IP layer protocol in
skb_flow_dissect()") broke IPoIB.
Only current offender is sch_choke, and this one do not need an
absolutely precise flow key.
If we store 17 bytes of flow key, its more than enough. (Its the actual
size of flow_keys if it was a packed structure, but we might add new
fields at the end of it later)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: e0f31d8498 ("flow_keys: Record IP layer protocol in skb_flow_dissect()")
Signed-off-by: David S. Miller <davem@davemloft.net>
Functions supplied in ip6_udp_tunnel.c are only needed when IPV6 is
selected. When IPV6 is not selected, those functions are stubbed out
in udp_tunnel.h.
==================================================================
net/ipv6/ip6_udp_tunnel.c:15:5: error: redefinition of 'udp_sock_create6'
int udp_sock_create6(struct net *net, struct udp_port_cfg *cfg,
In file included from net/ipv6/ip6_udp_tunnel.c:9:0:
include/net/udp_tunnel.h:36:19: note: previous definition of 'udp_sock_create6' was here
static inline int udp_sock_create6(struct net *net, struct udp_port_cfg *cfg,
==================================================================
Fixes: fd384412e udp_tunnel: Seperate ipv6 functions into its own file
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit fb5d1e9e12 ("openvswitch: Build flow cmd netlink reply only if needed."),
the new flows are not notified to the listeners of OVS_FLOW_MCGROUP.
This commit fixes the problem by using the genl function, ie
genl_has_listerners() instead of netlink_has_listeners().
Signed-off-by: Samuel Gauthier <samuel.gauthier@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added netlink attrs to configure FOU encapsulation for GRE, netlink
handling of these flags, and properly adjust MTU for encapsulation.
ip_tunnel_encap is called from ip_tunnel_xmit to actually perform FOU
encapsulation.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netlink handling for IP tunnel encapsulation parameters and
and adjustment of MTU for encapsulation. ip_tunnel_encap is called
from ip_tunnel_xmit to actually perform FOU encapsulation.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added netlink handling of IP tunnel encapulation paramters, properly
adjust MTU for encapsulation. Added ip_tunnel_encap call to
ipip6_tunnel_xmit to actually perform FOU encapsulation.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes IP tunnel to support (secondary) encapsulation,
Foo-over-UDP. Changes include:
1) Adding tun_hlen as the tunnel header length, encap_hlen as the
encapsulation header length, and hlen becomes the grand total
of these.
2) Added common netlink define to support FOU encapsulation.
3) Routines to perform FOU encapsulation.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement fou_gro_receive and fou_gro_complete, and populate these
in the correponsing udp_offloads for the socket. Added ipproto to
udp_offloads and pass this from UDP to the fou GRO routine in proto
field of napi_gro_cb structure.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides a receive path for foo-over-udp. This allows
direct encapsulation of IP protocols over UDP. The bound destination
port is used to map to an IP protocol, and the XFRM framework
(udp_encap_rcv) is used to receive encapsulated packets. Upon
reception, the encapsulation header is logically removed (pointer
to transport header is advanced) and the packet is reinjected into
the receive path with the IP protocol indicated by the mapping.
Netlink is used to configure FOU ports. The configuration information
includes the port number to bind to and the IP protocol corresponding
to that port.
This should support GRE/UDP
(http://tools.ietf.org/html/draft-yong-tsvwg-gre-in-udp-encap-02),
as will as the other IP tunneling protocols (IPIP, SIT).
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Want to be able to use these in foo-over-udp offloads, etc.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tc_u32_sel 'sel' in tc_u_knode expects to be the last element in the
structure and pads the structure with tc_u32_key fields for each key.
kzalloc(sizeof(*n) + s->nkeys*sizeof(struct tc_u32_key), GFP_KERNEL)
CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-09-17
Please pull this batch of fixes intended for the 3.17 stream...
Arend van Spriel sends a trio of minor brcmfmac fixes, including a
fix for a Kconfig/build issue, a fix for a crash (null reference),
and a regression fix related to event handling on a P2P interface.
Hante Meuleman follows-up with a brcmfmac fix for a memory leak.
Johannes Stezenbach brings an ath9k_htc fix for a regression related
to hardware decryption offload.
Marcel Holtmann delivers a one-liner to properly mark a device ID
table in rfkill-gpio.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
pfifo_fast and htb use skb lists, without needing their spinlocks.
(They instead use the standard qdisc lock)
We can use __skb_queue_head_init() instead of skb_queue_head_init()
to be consistent.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switch drivers (e.g: bcm_sf2) may have to communicate specific
workarounds or flags towards the PHY device driver. Allow switches
driver to be delegated that task by introducing a get_phy_flags()
callback which will do just that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract from sock_alloc_send_pskb() code building skb with frags,
so that we can reuse this in other contexts.
Intent is to use it from tcp_send_rcvq(), tcp_collapse(), ...
We also want to replace some skb_linearize() calls to a more reliable
strategy in pathological cases where we need to reduce number of frags.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now we no longer rely on having tcp headers for skbs in receive queue,
tcp repair do not need to build fake ones.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify l2tp implementation using common UDP tunnel APIs.
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added a few more UDP tunnel APIs that can be shared by UDP based
tunnel protocol implementation. The main ones are highlighted below.
setup_udp_tunnel_sock() configures UDP listener socket for
receiving UDP encapsulated packets.
udp_tunnel_xmit_skb() and upd_tunnel6_xmit_skb() transmit skb
using UDP encapsulation.
udp_tunnel_sock_release() closes the UDP tunnel listener socket.
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ip6_udp_tunnel.c for ipv6 UDP tunnel functions to avoid ifdefs
in udp_tunnel.c
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch exposes the ruleset generation ID in three ways:
1) The new command NFT_MSG_GETGEN that exposes the 32-bits ruleset
generation ID. This ID is incremented in every commit and it
should be large enough to avoid wraparound problems.
2) The less significant 16-bits of the generation ID are exposed through
the nfgenmsg->res_id header field. This allows us to quickly catch
if the ruleset has change between two consecutive list dumps from
different object lists (in this specific case I think the risk of
wraparound is unlikely).
3) Userspace subscribers may receive notifications of new rule-set
generation after every commit. This also provides an alternative
way to monitor the generation ID. If the events are lost, the
userspace process hits a overrun error, so it knows that it is
working with a stale ruleset anyway.
Patrick spotted that rule-set transformations in userspace may take
quite some time. In that case, it annotates the 32-bits generation ID
before fetching the rule-set, then:
1) it compares it to what we obtain after the transformation to
make sure it is not working with a stale rule-set and no wraparound
has ocurred.
2) it subscribes to ruleset notifications, so it can watch for new
generation ID.
This is complementary to the NLM_F_DUMP_INTR approach, which allows
us to detect an interference in the middle one single list dumping.
There is no way to explicitly check that an interference has occurred
between two list dumps from the kernel, since it doesn't know how
many lists the userspace client is actually going to dump.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Simon Horman says:
====================
This pull requests makes the following changes:
* Add simple weighted fail-over scheduler.
- Unlike other IPVS schedulers this offers fail-over rather than load
balancing. Connections are directed to the appropriate server based
solely on highest weight value and server availability.
- Thanks to Kenny Mathis
* Support IPv6 real servers in IPv4 virtual-services and vice versa
- This feature is supported in conjunction with the tunnel (IPIP)
forwarding mechanism. That is, IPv4 may be forwarded in IPv6 and
vice versa.
- The motivation for this is to allow more flexibility in the
choice of IP version offered by both virtual-servers and
real-servers as they no longer need to match: An IPv4 connection from an
end-user may be forwarded to a real-server using IPv6 and vice versa.
- Further work need to be done to support this feature in conjunction
with connection synchronisation. For now such configurations are
not allowed.
- This change includes update to netlink protocol, adding a new
destination address family attribute. And the necessary changes
to plumb this information throughout IPVS.
- Thanks to Alex Gartrell and Julian Anastasov
====================
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
While tracking down the MAX_AH_AUTH_LEN crash in an old kernel
I thought that this limit was rather arbitrary and we should
just get rid of it.
In fact it seems that we've already done all the work needed
to remove it apart from actually removing it. This limit was
there in order to limit stack usage. Since we've already
switched over to allocating scratch space using kmalloc, there
is no longer any need to limit the authentication length.
This patch kills all references to it, including the BUG_ONs
that led me here.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Remove the temporary consistency check and add a case statement to only
allow ipip mixed dests.
Signed-off-by: Alex Gartrell <agartrell@fb.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Use the new address family field cp->daf when printing
cp->daddr in logs or connection listing.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Alex Gartrell <agartrell@fb.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Needed to support svc->af != dest->af.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Alex Gartrell <agartrell@fb.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
This ensures the tcf_exts_init() is called for all cases.
Fixes: 952313bd62 ("net: sched: cls_cgroup use RCU")
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pravin B Shelar says:
====================
Open vSwitch
Following patches adds recirculation and hash action to OVS.
First patch removes pointer to stack object. Next three patches
does code restructuring which is required for last patch.
Recirculation implementation is changed, according to comments from
David Miller, to avoid using recursive calls in OVS. It is using
queue to record recirc action and deferred recirc is executed at
the end of current actions execution.
v1-v2:
Changed subsystem name in subject to openvswitch
v2-v3:
Added patch to remove pkt_key pointer from skb->cb.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For the ACPI based switches the MODULE_DEVICE_TABLE is missing to
export the entries for module auto-loading.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When allocating a new structure we also need to call tcf_exts_init
to initialize exts.
A follow up patch might be in order to remove some of this code
and do tcf_exts_assign(). With this we could remove the
tcf_exts_init/tcf_exts_change pattern for some of the classifiers.
As part of the future tcf_actions RCU series this will need to be
done. For now fix the call here.
Fixes e35a8ee599 ("net: sched: fw use RCU")
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tree: git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next.git master
head: 54996b529a
commit: c7953ef230 [625/646] net: sched: cls_cgroup use RCU
net/sched/cls_cgroup.c:130 cls_cgroup_change() warn: possible memory leak of 'new'
net/sched/cls_cgroup.c:135 cls_cgroup_change() warn: possible memory leak of 'new'
net/sched/cls_cgroup.c:139 cls_cgroup_change() warn: possible memory leak of 'new'
Fixes: c7953ef230 ("net: sched: cls_cgroup use RCU")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kbuild test robot reported an unused variable cpu in cls_u32.c
after the patch below. This happens when PERF and MARK config
variables are disabled
Fix this is to use separate variables for perf and mark
and define the cpu variable inside the ifdef logic.
Fixes: 459d5f626d ("net: sched: make cls_u32 per cpu")'
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: commit 331b72922c ("net: sched: RCU cls_tcindex")
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-By: John Fastabend <john.r.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we genarate a queueing route if we have matching policies
but can not resolve the states and the sysctl xfrm_larval_drop is
disabled. Here we assume that dst_output() is called to kill the
queued packets. Unfortunately this assumption is not true in all
cases, so it is possible that these packets leave the system unwanted.
We fix this by generating queueing routes only from the
route lookup functions, here we can guarantee a call to
dst_output() afterwards.
Fixes: a0073fe18e ("xfrm: Add a state resolution packet queue")
Reported-by: Konstantinos Kolelis <k.kolelis@sirrix.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Currently we genarate a blackhole route route whenever we have
matching policies but can not resolve the states. Here we assume
that dst_output() is called to kill the balckholed packets.
Unfortunately this assumption is not true in all cases, so
it is possible that these packets leave the system unwanted.
We fix this by generating blackhole routes only from the
route lookup functions, here we can guarantee a call to
dst_output() afterwards.
Fixes: 2774c131b1 ("xfrm: Handle blackhole route creation via afinfo.")
Reported-by: Konstantinos Kolelis <k.kolelis@sirrix.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Recirc action allows a packet to reenter openvswitch processing.
currently openvswitch lookup flow for packet received and execute
set of actions on that packet, with help of recirc action we can
process/modify the packet and recirculate it back in openvswitch
for another pass.
OVS hash action calculates 5-tupple hash and set hash in flow-key
hash. This can be used along with recirculation for distributing
packets among different ports for bond devices.
For example:
OVS bonding can use following actions:
Match on: bond flow; Action: hash, recirc(id)
Match on: recirc-id == id and hash lower bits == a;
Action: output port_bond_a
Signed-off-by: Andy Zhou <azhou@nicira.com>
Acked-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
The current sample() function implementation is more complicated
than necessary in handling single user space action optimization
and skb reference counting. There is no functional changes.
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Currently tun_key is used for passing tunnel information
on ingress and egress path, this cause confusion. Following
patch removes its use on ingress path make it egress only parameter.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Andy Zhou <azhou@nicira.com>
OVS flow extract is called on packet receive or packet
execute code path. Following patch defines separate API
for extracting flow-key in packet execute code path.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Andy Zhou <azhou@nicira.com>
