AM33XX only supports DT boot mode and with addition of
extracting module resources like, irq, dma and address space
from DT block, so now we can remove duplicate information from
hwmod data file.
This patch cleanups-up/deletes,
- All references to "omap_hwmod_irq_info" data.
- All references to "omap_hwmod_dma_info" data.
- References to "omap_hwmod_addr_space" of the modules
for which DT node is available with required address
space information.
- For the modules where "sysc" field is not applicable,
we don't need module address space, so remove them as well.
- The hwmod like firewall etc which are not useful are also
deleted.
This cleanup gets us around ~1100 LOC of negative diff.
Patch is boot tested on AM335x-EVM along with below modules -
- Matrix-keypad
- Volume up/down keys
- Ethernet
- RTC
- WDT
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap36xx_pwrdn_clk_enable_with_hsdiv_restore expects the parent hw of
the clock to be a clk_hw_omap. However, looking at cclock3xxx_data.c,
all concerned clock have parent defined as clk_divider. Fix the
function to use clk_divider. Tested with 3.9 on dm3730.
Signed-off-by: Jean-Philippe François <jp.francois@cynove.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The "runtime idle" helper routine, rpm_idle(), currently ignores
return values from .runtime_idle() callbacks executed by it.
However, it turns out that many subsystems use
pm_generic_runtime_idle() which checks the return value of the
driver's callback and executes pm_runtime_suspend() for the device
unless that value is not 0. If that logic is moved to rpm_idle()
instead, pm_generic_runtime_idle() can be dropped and its users
will not need any .runtime_idle() callbacks any more.
Moreover, the PCI, SCSI, and SATA subsystems' .runtime_idle()
routines, pci_pm_runtime_idle(), scsi_runtime_idle(), and
ata_port_runtime_idle(), respectively, as well as a few drivers'
ones may be simplified if rpm_idle() calls rpm_suspend() after 0 has
been returned by the .runtime_idle() callback executed by it.
To reduce overall code bloat, make the changes described above.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
The UART2 hwmod structure is pointing to the EDMA channels of UART1,
which doesn't look right. This patch fixes this by making the UART2
hwmod structure to a new structure that lists the EDMA channels to be
used by the UART2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This is omap4+ only and no longer needed as omap4+ can be booted
using device tree.
Also remove the related pdata handling from the driver and the
now unneeded platform_data/omap_ocp2scp.h.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now boot with device tree. If you don't want to update u-boot,
you can boot with appended DTB with the following instructions:
1. Make sure you have the appended DTB support in .config
CONFIG_ARM_APPENDED_DTB=y
CONFIG_ARM_ATAG_DTB_COMPAT=y
CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND=y
2. Build the zImage
$ ARCH=arm CROSS_COMPILE=... make zImage
3. Build the device tree blobs
$ ARCH=arm CROSS_COMPILE=... make dtbs
4. Append the correct panda dtb to zImage
Depending on your hardware it's omap4-panda.dtb, omap4-panda-a4.dtb
or omap4-panda-es.dtb.
$ cat arch/arm/boot/zImage arch/arm/boot/dts/omap4-panda-es.dtb > /tmp/appended
5. Use mkimage to produce the appended device tree uImage
$ mkimage -A arm -O linux -T kernel -C none -a 0x80008000 -e 0x80008000 \
-n "Linux" -d /tmp/appended /tmp/uImage
Signed-off-by: Tony Lindgren <tony@atomide.com
We can now boot with device tree. If you don't want to update u-boot,
you can boot with appended DTB with the following instructions:
1. Make sure you have the appended DTB support in .config
CONFIG_ARM_APPENDED_DTB=y
CONFIG_ARM_ATAG_DTB_COMPAT=y
CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND=y
2. Build the zImage
$ ARCH=arm CROSS_COMPILE=... make zImage
3. Build the device tree blobs
$ ARCH=arm CROSS_COMPILE=... make dtbs
4. Append the dtb to zImage
$ cat arch/arm/boot/zImage arch/arm/boot/dts/omap4-sdp.dtb > /tmp/appended
5. Use mkimage to produce the appended device tree uImage
$ mkimage -A arm -O linux -T kernel -C none -a 0x80008000 -e 0x80008000 \
-n "Linux" -d /tmp/appended /tmp/uImage
Signed-off-by: Tony Lindgren <tony@atomide.com>
Without WLAN we cannot switch omap4 to use device tree
only booting. This patch can be reverted when the
binding for wl12xx is added.
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: devicetree-discuss@lists.ozlabs.org
Tested-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit a819c4f1 (ARM: OMAP3: PM: Only access IVA if one exists)
changed PM to not access IVA registers on omaps that don't have
them. Turns out we still need to idle iva2 as otherwise
iva2_pwrdm will stay on and block deeper idle states.
It seems that the only part of the reset that may not be needed
is the setting of the iva2 boot mode to idle. But as that register
seems to be there and is harmless if no iva2 is on the SoC, it's
probably safest to do the complete reset.
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
with DT.
Basic build, boot, and PM test logs are here - unfortunately, not for
the DT case yet:
http://www.pwsan.com/omap/testlogs/uart_idle_fix_v3.10-rc/20130519164010/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJRmVyFAAoJEMePsQ0LvSpL7esP/3Jxl0XhCHnZdS19Ts+wg3Uj
u1kfLN5WVaPEuXbBEuM/wEnMcSuWeAxhJEwEFvVURfVmUkbSWpQ9vRtXNFlbKAro
qiAG7Rc+9dqZqzpgSn7iV/KhxZiYu7du1zMJP1tR15QLlswJtuLhG4D3im6SZ7qh
QQ/iESsQp7fzASguv6Bo8piw3M7PIF7zgRw5zki2dQBowGqHqQcKFcQgDADeeIg/
dToCKRJb91F9/von8D7D8TvRLo0DS/uxTVLvXLteB8hqIbLXJel6llYanw3JFZyt
1D6Ygml4RQUlLYhq4ERkAsMtb8s9cwk/IvkAyksCytORG7s5+4jFxKhAu+6P8tjv
caf5yQNT8qtRgyB7QGA0F75tNKV8Nm4j3BpyYLz1690ZC6tDV3+9QQOnEj6YR6bJ
X7+x0eoRrJS3ZUakTdDZSBXW4YxWZUHNzbpSpwDEQKaMgR2FLq0dbDYMqYUkMHNH
FL+0mfeXMcg8NBaZfGyxwjsxme6aN4LuJ3SsLVSFjDA9qNXqFE4DARAZwyiQixGG
f8z5KfLhKr+zI+iiuK439U4f6AW7uguHHvUL8eEzyjEA++TvSm0TzZURafX5Ldhh
U8y3vudHAszZr6gLEBqUsvJZBmNWPVhkL5m8PRFOBIJqjqS3dyh/zbA+gB3TNRcM
gLdggBxEL2w8ESpWj+UH
=DRuE
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-a-for-3.10-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
From Paul Walmsley:
Fix the OMAP serial driver to work correctly on OMAP4 when booting
with DT.
* tag 'omap-fixes-a-for-3.10-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: OMAP2+: hwmod: Remove sysc slave idle and auto idle apis
SERIAL: OMAP: Remove the slave idle handling from the driver
ARM: OMAP2+: serial: Remove the un-used slave idle hooks
ARM: OMAP2+: hwmod-data: UART IP needs software control to manage sidle modes
ARM: OMAP2+: hwmod: Add a new flag to handle SIDLE in SWSUP only in active
ARM: OMAP2+: hwmod: Fix sidle programming in _enable_sysc()/_idle_sysc()
Signed-off-by: Olof Johansson <olof@lixom.net>
With the OMAP serial driver sysc cleanup patches in this series, we can
now remove the hwmod external apis for sysc fiddling.
While at this, also remove unused sysc auto idle api from hwmod code.
Tested-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Rajendra nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org> # OMAP4/Panda
Signed-off-by: Paul Walmsley <paul@pwsan.com>
UART IP idle handling now taken care by runtime pm backend(hwmod) indirectly
and OMAP serial driver is also cleaned up accordingly.
So remove the un-used slave idle platforms hooks now.
Tested-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Rajendra nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org> # OMAP4/Panda
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP UART IP needs software control for slave idle modes based on functional
state of the IP. i.e The IP slave idle settings should be set to 'noidle' when
being used and then put back to 'smart_idle' when unused. Currently this is
handled by the driver with function pointers implemented in platform code.
This however breaks in case of device tree because of missing idle handling
APIs.
Previous patches in this series added a flag HWMOD_SWSUP_SIDLE_ACTIVE which
takes care of the mentioned requirement. Hence add the flag for all UART IPs
to take advantage of feature supported by framework.
Subsequent patches removes the slave idle handling from driver code.
Tested-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org> # OMAP4/Panda
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some IPs (like UART) need the sidle mode to be controlled in SW only
while they are active. Once they go inactive, they need the IP to be
put back in HW control so they are also wakeup capable.
The flag HWMOD_SWSUP_SIDLE takes care of IPs which need the sidle
mode to be *always* controlled in SWSUP. We now have a need to control
IPs sidle mode in SWSUP only while its active.
So define a new flag 'HWMOD_SWSUP_SIDLE_ACT' to help the framework
know about these new IP requirements.
Tested-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org> # OMAP4/Panda
Signed-off-by: Paul Walmsley <paul@pwsan.com>
_enable_sysc() and _idle_sysc() handle the midle mode programming correctly
and program HWMOD_IDLEMODE_SMART or HWMOD_IDLEMODE_SMART_WKUP respectively
for supported IPs (The ones which support hardware controlled midle modes)
However the same programming logic is missing when it comes to sidle mode
programming. Here they seem to just set HWMOD_IDLEMODE_SMART (Again for the
ones which support hardware controlled sidle modes)
This problem was hidden due to the fact that a call to _enable_wakeup()
in those same functions would overwrite the idlemodes and program them
correctly (to HWMOD_IDLEMODE_SMART_WKUP in the supported cases)
So fix the sidlemode handling correctly in these functions and handle the
_enable_wakeup() for SIDLEMODE supported IPs same as the way its handled
for MIDLEMODE supported ones.
Tested-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org> # OMAP4/Panda
Signed-off-by: Paul Walmsley <paul@pwsan.com>
It is required to enable respective clock-domain before
enabling any clock/module inside that clock-domain.
During common-clock migration, .clkdm_name field got missed
for "clkdiv32k_ick" clock, which leaves "clk_24mhz_clkdm"
unused; so it will be disabled even if childs of this clock-domain
is enabled, which keeps child modules in idle mode.
This fixes the kernel crash observed on AM335xEVM-SK platform,
where clkdiv32_ick clock is being used as a gpio debounce clock
and since clkdiv32k_ick is in idle mode it leads to below crash -
Crash Log:
==========
[ 2.598347] Unhandled fault: external abort on non-linefetch (0x1028) at
0xfa1ac150
[ 2.606434] Internal error: : 1028 [#1] SMP ARM
[ 2.611207] Modules linked in:
[ 2.614449] CPU: 0 Not tainted (3.8.4-01382-g1f449cd-dirty #4)
[ 2.620973] PC is at _set_gpio_debounce+0x60/0x104
[ 2.626025] LR is at clk_enable+0x30/0x3c
Cc: stable@vger.kernel.org # v3.9
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 8c8a777 (ARM: OMAP2+: Add function to read GPMC settings from
device-tree) added a device-tree property "gpmc,device-nand" to indicate
is the GPMC child device is NAND. This commit should have updated the
GPMC NAND documentation (Documentation/devicetree/bindings/mtd/gpmc-nand.txt)
to list the property "gpmc,device-nand" as a required property and also
updated the example. However, this property is redundant and not needed
because the GPMC child device node for NAND is called "nand". Therefore,
remove this property.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP devices support various NAND transfer modes.
Currently all device-tree definitions will use the default "prefetch
polled" mode, so this patch enables the transfer mode to be specified
in the device-tree.
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
Acked-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch removes omap2_nand_gpmc_retime() which was used to quirk
some timing values before gpmc_cs_set_timings(). Due to recent changes,
gpmc_cs_set_timings() has evolved so that there is no more need for a
retime function.
To keep the gpmc configuration consistent for legacy board files, this
patch also adds oe_on and we_on to nand_default_timings[] as they
would be by the retime function.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Support for OMAP5 is added to the omap_dsp_ctrl_write_boot_addr()
to enable the DSP boot.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove "no_idle_on_suspend" check, since respective
driver should be able to prevent idling of an
omap device whenever required.
Driver's can get same behavior by just returning -EBUSY
from their ->runtime_suspend only during suspend.
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Rajendra nayak <rnayak@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
"no_console_suspend" is no longer handled in platform file,
Since the omap serial driver is now adapted to prevent
console UART idleing during suspend.
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Rajendra nayak <rnayak@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
- Few GPMC fixes and binding doc updates noted after sending
pull requests for the GPMC branch.
- Board fixes for beagle usb host and rx51 spi probe order
- SoC fixes dt earlyprintk, omap1 dma and omap2+ id.c error
handling fixes
Then few minor things that are not strictly fixes but are good
to get out of the way:
- Add missing legacy mux registers for am/dm73x gpio
- Add detection for am33xx pg2.1 silicon
- Enable twl4030 audio modules in defconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=lnij
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.10/fixes-for-merge-window-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Omap fixes for things that were discovered during the merge window:
- Few GPMC fixes and binding doc updates noted after sending
pull requests for the GPMC branch.
- Board fixes for beagle usb host and rx51 spi probe order
- SoC fixes dt earlyprintk, omap1 dma and omap2+ id.c error
handling fixes
Then few minor things that are not strictly fixes but are good
to get out of the way:
- Add missing legacy mux registers for am/dm73x gpio
- Add detection for am33xx pg2.1 silicon
- Enable twl4030 audio modules in defconfig
* tag 'omap-for-v3.10/fixes-for-merge-window-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove bogus IS_ERR_OR_NULL checking from id.c
ARM: OMAP4+: omap2plus_defconfig: Enable audio via TWL6040 as module
ARM: OMAP2: AM33XX: id: Add support for new AM335x PG2.1 Si
omap: mux: add AM/DM37x gpios
ARM: OMAP1: DMA: fix error handling in omap1_system_dma_init()
ARM: OMAP2+: omap_device: use late_initcall_sync
ARM: OMAP: RX-51: change probe order of touchscreen and panel SPI devices
ARM: OMAP3: Beagle: Fix USB Host on beagle xM Ax/Bx
ARM: OMAP2+: only WARN if a GPMC child probe function fail
ARM: OMAP2+: only search for GPMC DT child nodes on probe
Documentation: dt: update properties in TI GPMC NAND example
Documentation: dt: update TI GPMC ethernet binding properties
Signed-off-by: Olof Johansson <olof@lixom.net>
* late/fixes:
ARM: OMAP2+: Fix unmet direct dependencies for SERIAL_OMAP
ARM: ux500: always select ABX500_CORE
ARM: SIRF: select SMP_ON_UP only on SMP builds
ARM: SPEAr: conditionalize l2x0 support
ARM: imx: build CPU suspend code only when needed
ARM: OMAP: build SMP code only for OMAP4/5
ARM: tegra: Tegra114 needs CPU_FREQ_TABLE
ARM: default machine descriptor for multiplatform
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull slave-dmaengine updates from Vinod Koul:
"This time we have dmatest improvements from Andy along with dw_dmac
fixes. He has also done support for acpi for dmanegine.
Also we have bunch of fixes going in DT support for dmanegine for
various folks. Then Haswell and other ioat changes from Dave and
SUDMAC support from Shimoda."
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (53 commits)
dma: tegra: implement suspend/resume callbacks
dma:of: Use a mutex to protect the of_dma_list
dma: of: Fix of_node reference leak
dmaengine: sirf: move driver init from module_init to subsys_initcall
sudmac: add support for SUDMAC
dma: sh: add Kconfig
at_hdmac: move to generic DMA binding
ioatdma: ioat3_alloc_sed can be static
ioatdma: Adding write back descriptor error status support for ioatdma 3.3
ioatdma: S1200 platforms ioatdma channel 2 and 3 falsely advertise RAID cap
ioatdma: Adding support for 16 src PQ ops and super extended descriptors
ioatdma: Removing hw bug workaround for CB3.x .2 and earlier
dw_dmac: add ACPI support
dmaengine: call acpi_dma_request_slave_channel as well
dma: acpi-dma: introduce ACPI DMA helpers
dma: of: Remove unnecessary list_empty check
DMA: OF: Check properties value before running be32_to_cpup() on it
DMA: of: Constant names
ioatdma: skip silicon bug workaround for pq_align for cb3.3
ioatdma: Removing PQ val disable for cb3.3
...
Commit 6770b211 (ARM: OMAP2+: Export SoC information to userspace)
had some broken return value handling as noted by Russell King:
+ soc_dev = soc_device_register(soc_dev_attr);
+ if (IS_ERR_OR_NULL(soc_dev)) {
+ kfree(soc_dev_attr);
+ return;
+ }
+
+ parent = soc_device_to_device(soc_dev);
+ if (!IS_ERR_OR_NULL(parent))
+ device_create_file(parent, &omap_soc_attr);
This is nonsense. For the first, IS_ERR() is sufficient. For the second,
tell me what error checking is required in the return value of this
function:
struct device *soc_device_to_device(struct soc_device *soc_dev)
{
return &soc_dev->dev;
}
when you've already determined that the passed soc_dev is a valid pointer.
If you read the comments against the prototype:
/**
* soc_device_to_device - helper function to fetch struct device
* @soc: Previously registered SoC device container
*/
struct device *soc_device_to_device(struct soc_device *soc);
if "soc" is valid, it means the "previously registered SoC device container"
must have succeeded and that can only happen if the struct device has been
registered. Ergo, there will always be a valid struct device pointer for
any registered SoC device container. Therefore, if soc_device_register()
succeeds, then the return value from soc_device_to_device() will always be
valid and no error checking of it is required.
Simples. The rule as ever applies here: get to know the APIs your using
and don't fumble around in the dark hoping that you'll get this stuff
right.
Fix it as noted by Russell.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for chip id detection of AM335x PG2.1 Silicon.
Currently omap3xxx_check_revision() detects PG1.0 and PG2.0 only,
this patch extends it by adding PG2.1 Si support.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If DEBUG_LL and earlyprintk are enabled, and omap-serial.c is compiled
as a module, the kernel boot hangs early as the clocks for serial port
are cut while earlyprintk still uses the port.
The problem is a race between the late_initcall for omap_device (which
idles devices that have no drivers) and the late_initcall in
kernel/printk.c which turns off the earlyconsole. Any printks
that happen between this omap_device late initcall and the earlyconsole
late initcall will crash when accessing the UART.
The fix is to ensure the omap_device initcall happens after the
earlyconsole initcall.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 9fdca9df (spi: omap2-mcspi: convert to module_platform_driver)
broke the SPI display/panel driver probe on RX-51/N900. The exact cause is
not fully understood, but it seems to be related to the probe order. SPI
communication to the panel driver (spi1.2) fails unless the touchscreen
(spi1.0) has been probed/initialized before. When the omap2-mcspi driver
was converted to a platform driver, it resulted in that the devices are
probed immediately after the board registers them in the order they are
listed in the board file.
Fix the issue by moving the touchscreen before the panel in the SPI
device list.
The patch fixes the following failure:
[ 1.260955] acx565akm spi1.2: invalid display ID
[ 1.265899] panel-acx565akm display0: acx_panel_probe panel detect error
[ 1.273071] omapdss CORE error: driver probe failed: -19
Tested-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Joni Lapilainen <joni.lapilainen@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
On Beagle xM Rev. Ax/Bx, the USB power enable GPIO logic is
reversed when compared to other revisions i.e. it is
active high instead of active low.
Use the beagle_config.usb_pwr_level flag correctly so that
the power regulator can be configured at runtime.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
I badly screwed up the merge in commit 6fa52ed33b ("Merge tag
'drivers-for-linus' of git://git.kernel.org/pub/.../arm-soc") by
incorrectly taking the arch/arm/mach-omap2/* data fully from the merge
target because the 'drivers-for-linus' branch seemed to be a proper
superset of the duplicate ARM commits.
That was bogus: commit ff931c821b ("ARM: OMAP: clocks: Delay clk inits
atleast until slab is initialized") only existed in head, and the
changes to arch/arm/mach-omap2/timer.c from that commit got list.
Re-doing the merge more carefully, I do think this part was the only
thing I screwed up. Knock wood.
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These are cleanups and smaller changes that either depend on earlier
feature branches or came in late during the development cycle.
We normally try to get all cleanups early, so these are the exceptions:
- A follow-up on the clocksource reworks, hopefully the last time
we need to merge clocksource subsystem changes through arm-soc.
A first set of patches was part of the original 3.10 arm-soc cleanup
series because of interdependencies with timer drivers now moved out
of arch/arm.
- Migrating the SPEAr13xx platform away from using auxdata for DMA
channel descriptions towards using information in device tree,
based on the earlier SPEAr multiplatform series
- A few follow-ups on the Atmel SAMA5 support and other changes
for Atmel at91 based on the larger at91 reworks.
- Moving the armada irqchip implementation to drivers/irqchip
- Several OMAP cleanups following up on the larger series already
merged in 3.10.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=HWfp
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late cleanups from Arnd Bergmann:
"These are cleanups and smaller changes that either depend on earlier
feature branches or came in late during the development cycle. We
normally try to get all cleanups early, so these are the exceptions:
- A follow-up on the clocksource reworks, hopefully the last time we
need to merge clocksource subsystem changes through arm-soc.
A first set of patches was part of the original 3.10 arm-soc
cleanup series because of interdependencies with timer drivers now
moved out of arch/arm.
- Migrating the SPEAr13xx platform away from using auxdata for DMA
channel descriptions towards using information in device tree,
based on the earlier SPEAr multiplatform series
- A few follow-ups on the Atmel SAMA5 support and other changes for
Atmel at91 based on the larger at91 reworks.
- Moving the armada irqchip implementation to drivers/irqchip
- Several OMAP cleanups following up on the larger series already
merged in 3.10."
* tag 'cleanup-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
ARM: OMAP4: change the device names in usb_bind_phy
ARM: OMAP2+: Fix mismerge for timer.c between ff931c82 and da4a686a
ARM: SPEAr: conditionalize SMP code
ARM: arch_timer: Silence debug preempt warnings
ARM: OMAP: remove unused variable
serial: amba-pl011: fix !CONFIG_DMA_ENGINE case
ata: arasan: remove the need for platform_data
ARM: at91/sama5d34ek.dts: remove not needed compatibility string
ARM: at91: dts: add MCI DMA support
ARM: at91: dts: add i2c dma support
ARM: at91: dts: set #dma-cells to the correct value
ARM: at91: suspend both memory controllers on at91sam9263
irqchip: armada-370-xp: slightly cleanup irq controller driver
irqchip: armada-370-xp: move IRQ handler to avoid forward declaration
irqchip: move IRQ driver for Armada 370/XP
ARM: mvebu: move L2 cache initialization in init_early()
devtree: add binding documentation for sp804
ARM: integrator-cp: convert use CLKSRC_OF for timer init
ARM: versatile: use OF init for sp804 timer
ARM: versatile: add versatile dtbs to dtbs target
...
These are mostly new device tree bindings for existing drivers, as well
as changes to the device tree source files to add support for those
devices, and a couple of new boards, most notably Samsung's Exynos5
based Chromebook.
The changes depend on earlier platform specific updates and touch
the usual platforms: omap, exynos, tegra, mxs, mvebu and davinci.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G60S
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates (part 2) from Arnd Bergmann:
"These are mostly new device tree bindings for existing drivers, as
well as changes to the device tree source files to add support for
those devices, and a couple of new boards, most notably Samsung's
Exynos5 based Chromebook.
The changes depend on earlier platform specific updates and touch the
usual platforms: omap, exynos, tegra, mxs, mvebu and davinci."
* tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: add mshc controller node for Exynos4x12 SoCs
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
ARM: davinci: da850-evm: add SPI flash support
ARM: davinci: da850: override SPI DT node device name
ARM: davinci: da850: add SPI1 DT node
spi/davinci: add DT binding documentation
spi/davinci: no wildcards in DT compatible property
ARM: dts: mvebu: Convert mvebu device tree files to 64 bits
ARM: dts: mvebu: introduce internal-regs node
ARM: dts: mvebu: Convert all the mvebu files to use the range property
ARM: dts: mvebu: move all peripherals inside soc
ARM: dts: mvebu: fix cpus section indentation
ARM: davinci: da850: add EHRPWM & ECAP DT node
ARM/dts: OMAP3: fix pinctrl-single configuration
ARM: dts: Add OMAP3430 SDP NOR flash memory binding
ARM: dts: Add NOR flash bindings for OMAP2420 H4
...
musb device naming change.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=FjKm
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.10/fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into late/cleanup
From Tony Lindgren <tony@atomide.com>:
An urgent fix for a timer mismerge for and a regression fix for
musb device naming change.
* tag 'omap-for-v3.10/fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4: change the device names in usb_bind_phy
ARM: OMAP2+: Fix mismerge for timer.c between ff931c82 and da4a686a
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
After the device names are created using PLATFORM_DEVID_AUTO, the old
device names given in usb_bind_phy are no longer valid causing the musb
controller not to get the phy reference. Updated the usb_bind_phy with
the new device names to get MUSB functional in omap4 panda.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like the timer.c fixes in commit ff931c82 (ARM: OMAP: clocks:
Delay clk inits atleast until slab is initialized) got lost in a
merge with da4a686a (ARM: smp_twd: convert to use CLKSRC_OF init).
Without the omap_clk_init() calls none of OMAP family of devices
boot.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
[tony@atomide.com: updated comments to describe merge error]
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is no reason to keep the clksrc cleanups separate from the
other cleanups, and this resolves some merge conflicts.
Conflicts:
arch/arm/mach-spear/spear13xx.c
drivers/irqchip/Makefile
This is support for the ARM Chromebook, originally scheduled
as a "late" pull request. Since it's already late now, we
can combine this into the existing next/dt2 branch.
* late/dt:
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
These changes are all for board specific files. These used to make up a
large portion of the ARM changes in the past, but as we are generalizing
the support and moving to device tree probing, this has gotten
significantly smaller. The only platform actually adding new code here
at the moment is Renesas shmobile, as they are still busy converting
their code to device tree and have not come far enough to not need it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=2cfP
-----END PGP SIGNATURE-----
Merge tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board specific changes (part 1) from Olof Johansson:
"These changes are all for board specific files. These used to make up
a large portion of the ARM changes in the past, but as we are
generalizing the support and moving to device tree probing, this has
gotten significantly smaller.
The only platform actually adding new code here at the moment is
Renesas shmobile, as they are still busy converting their code to
device tree and have not come far enough to not need it."
* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
ARM: msm: USB_MSM_OTG needs USB_PHY
ARM: davinci: da850 evm: fix const qualifier placement
ARM: davinci: da850 board: add remoteproc support
ARM: pxa: move debug uart code
ARM: pxa: select PXA935 on saar & tavorevb
ARM: mmp: add more compatible names in gpio driver
ARM: pxa: move PXA_GPIO_TO_IRQ macro
ARM: pxa: remove cpu_is_xxx in gpio driver
ARM: Kirkwood: update Network Space Mini v2 description
ARM: Kirkwood: DT board setup for CloudBox
ARM: Kirkwood: sort board entries by ASCII-code order
ARM: OMAP: board-4430sdp: Provide regulator to pwm-backlight
ARM: OMAP: zoom: Use pwm stack for lcd and keyboard backlight
ARM: OMAP2+: omap2plus_defconfig: Add support for BMP085 pressure sensor
omap2+: Remove useless Makefile line
omap2+: Remove useless Makefile line
ARM: OMAP: RX-51: add missing regulator supply definitions for lis3lv02d
ARM: OMAP1: fix omap_udc registration
ARM: davinci: use is IS_ENABLED macro
ARM: kirkwood: add MACH_GURUPLUG_DT to defconfig
...
This is a rather large set of patches for device drivers that for one
reason or another the subsystem maintainer preferred to get merged
through the arm-soc tree. There are both new drivers as well as
existing drivers that are getting converted from platform-specific
code into standalone drivers using the appropriate subsystem
specific interfaces.
In particular, we can now have pinctrl, clk, clksource and irqchip
drivers in one file per driver, without the need to call into
platform specific interface, or to get called from platform specific
code, as long as all information about the hardware is provided
through a device tree.
Most of the drivers we touch this time are for clocksource. Since
now most of them are part of drivers/clocksource, I expect that we
won't have to touch these again from arm-soc and can let the
clocksource maintainers take care of these in the future.
Another larger part of this series is specific to the exynos platform,
which is seeing some significant effort in upstreaming and
modernization of its device drivers this time around, which
unfortunately is also the cause for the churn and a lot of the
merge conflicts.
There is one new subsystem that gets merged as part of this series:
the reset controller interface, which is a very simple interface
for taking devices on the SoC out of reset or back into reset.
Patches to use this interface on i.MX follow later in this merge
window, and we are going to have other platforms (at least tegra
and sirf) get converted in 3.11. This will let us get rid of
platform specific callbacks in a number of platform independent
device drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ZWk9
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Olof Johansson:
"This is a rather large set of patches for device drivers that for one
reason or another the subsystem maintainer preferred to get merged
through the arm-soc tree. There are both new drivers as well as
existing drivers that are getting converted from platform-specific
code into standalone drivers using the appropriate subsystem specific
interfaces.
In particular, we can now have pinctrl, clk, clksource and irqchip
drivers in one file per driver, without the need to call into platform
specific interface, or to get called from platform specific code, as
long as all information about the hardware is provided through a
device tree.
Most of the drivers we touch this time are for clocksource. Since now
most of them are part of drivers/clocksource, I expect that we won't
have to touch these again from arm-soc and can let the clocksource
maintainers take care of these in the future.
Another larger part of this series is specific to the exynos platform,
which is seeing some significant effort in upstreaming and
modernization of its device drivers this time around, which
unfortunately is also the cause for the churn and a lot of the merge
conflicts.
There is one new subsystem that gets merged as part of this series:
the reset controller interface, which is a very simple interface for
taking devices on the SoC out of reset or back into reset. Patches to
use this interface on i.MX follow later in this merge window, and we
are going to have other platforms (at least tegra and sirf) get
converted in 3.11. This will let us get rid of platform specific
callbacks in a number of platform independent device drivers."
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (256 commits)
irqchip: s3c24xx: add missing __init annotations
ARM: dts: Disable the RTC by default on exynos5
clk: exynos5250: Fix parent clock for sclk_mmc{0,1,2,3}
ARM: exynos: restore mach/regs-clock.h for exynos5
clocksource: exynos_mct: fix build error on non-DT
pinctrl: vt8500: wmt: Fix checking return value of pinctrl_register()
irqchip: vt8500: Convert arch-vt8500 to new irqchip infrastructure
reset: NULL deref on allocation failure
reset: Add reset controller API
dt: describe base reset signal binding
ARM: EXYNOS: Add arm-pmu DT binding for exynos421x
ARM: EXYNOS: Add arm-pmu DT binding for exynos5250
ARM: EXYNOS: Enable PMUs for exynos4
irqchip: exynos-combiner: Correct combined IRQs for exynos4
irqchip: exynos-combiner: Add set_irq_affinity function for combiner_irq
ARM: EXYNOS: fix compilation error introduced due to common clock migration
clk: exynos5250: Fix divider values for sclk_mmc{0,1,2,3}
clk: exynos4: export clocks required for fimc-is
clk: samsung: Fix compilation error
clk: tegra: fix enum tegra114_clk to match binding
...
Commit 8a6201b9 (ARM: OMAP2+: Fix unmet direct dependencies for zoom
for 8250 serial) fixed unmet direct dependencies for 8250, but failed
to do the same for omap serial. This can cause the following warning:
warning: (ARCH_OMAP2PLUS_TYPICAL) selects SERIAL_OMAP which has
unmet direct dependencies (TTY && HAS_IOMEM && GENERIC_HARDIRQS &&
ARCH_OMAP2PLUS).
We should not select drivers, they should be selected by the
user. Fix the issue by removing the select and adding them to
omap2plus_defconfig instead.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The OMAP platform code assumes that SMP is only ever enabled when
CONFIG_ARCH_OMAP4 or CONFIG_SOC_OMAP5 is enabled, which is not
necessarirly true in a multiplatform configuration.
arch/arm/mach-omap2/built-in.o: In function `omap4_smp_prepare_cpus':
:(.init.text+0x413c): undefined reference to `omap_get_wakeupgen_base'
:(.init.text+0x415c): undefined reference to `omap_secure_apis_support'
arch/arm/mach-omap2/built-in.o: In function `omap4_boot_secondary':
:(.cpuinit.text+0x28): undefined reference to `omap_get_wakeupgen_base'
:(.cpuinit.text+0x3c): undefined reference to `omap_secure_apis_support'
arch/arm/mach-omap2/built-in.o: In function `omap4_cpu_die':
:(.ref.text+0x8): undefined reference to `omap_get_wakeupgen_base'
:(.ref.text+0x10): undefined reference to `omap_secure_apis_support'
:(.ref.text+0x4c): undefined reference to `omap4_hotplug_cpu'
:(.ref.text+0x50): undefined reference to `omap_secure_apis_support'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Pull ARM updates from Russell King:
"The major items included in here are:
- MCPM, multi-cluster power management, part of the infrastructure
required for ARMs big.LITTLE support.
- A rework of the ARM KVM code to allow re-use by ARM64.
- Error handling cleanups of the IS_ERR_OR_NULL() madness and fixes
of that stuff for arch/arm
- Preparatory patches for Cortex-M3 support from Uwe Kleine-König.
There is also a set of three patches in here from Hugh/Catalin to
address freeing of inappropriate page tables on LPAE. You already
have these from akpm, but they were already part of my tree at the
time he sent them, so unfortunately they'll end up with duplicate
commits"
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (77 commits)
ARM: EXYNOS: remove unnecessary use of IS_ERR_VALUE()
ARM: IMX: remove unnecessary use of IS_ERR_VALUE()
ARM: OMAP: use consistent error checking
ARM: cleanup: OMAP hwmod error checking
ARM: 7709/1: mcpm: Add explicit AFLAGS to support v6/v7 multiplatform kernels
ARM: 7700/2: Make cpu_init() notrace
ARM: 7702/1: Set the page table freeing ceiling to TASK_SIZE
ARM: 7701/1: mm: Allow arch code to control the user page table ceiling
ARM: 7703/1: Disable preemption in broadcast_tlb*_a15_erratum()
ARM: mcpm: provide an interface to set the SMP ops at run time
ARM: mcpm: generic SMP secondary bringup and hotplug support
ARM: mcpm_head.S: vlock-based first man election
ARM: mcpm: Add baremetal voting mutexes
ARM: mcpm: introduce helpers for platform coherency exit/setup
ARM: mcpm: introduce the CPU/cluster power API
ARM: multi-cluster PM: secondary kernel entry code
ARM: cacheflush: add synchronization helpers for mixed cache state accesses
ARM: cpu hotplug: remove majority of cache flushing from platforms
ARM: smp: flush L1 cache in cpu_die()
ARM: tegra: remove tegra specific cpu_disable()
...
