In some cases the kernel needs to execute an instruction from the delay
slot of an emulated branch instruction. These cases include:
- Emulated floating point branch instructions (bc1[ft]l?) for systems
which don't include an FPU, or upon which the kernel is run with the
"nofpu" parameter.
- MIPSr6 systems running binaries targeting older revisions of the
architecture, which may include branch instructions whose encodings
are no longer valid in MIPSr6.
Executing instructions from such delay slots is done by writing the
instruction to memory followed by a trap, as part of an "emuframe", and
executing it. This avoids the requirement of an emulator for the entire
MIPS instruction set. Prior to this patch such emuframes are written to
the user stack and executed from there.
This patch moves FP branch delay emuframes off of the user stack and
into a per-mm page. Allocating a page per-mm leaves userland with access
to only what it had access to previously, and compared to other
solutions is relatively simple.
When a thread requires a delay slot emulation, it is allocated a frame.
A thread may only have one frame allocated at any one time, since it may
only ever be executing one instruction at any one time. In order to
ensure that we can free up allocated frame later, its index is recorded
in struct thread_struct. In the typical case, after executing the delay
slot instruction we'll execute a break instruction with the BRK_MEMU
code. This traps back to the kernel & leads to a call to do_dsemulret
which frees the allocated frame & moves the user PC back to the
instruction that would have executed following the emulated branch.
In some cases the delay slot instruction may be invalid, such as a
branch, or may trigger an exception. In these cases the BRK_MEMU break
instruction will not be hit. In order to ensure that frames are freed
this patch introduces dsemul_thread_cleanup() and calls it to free any
allocated frame upon thread exit. If the instruction generated an
exception & leads to a signal being delivered to the thread, or indeed
if a signal simply happens to be delivered to the thread whilst it is
executing from the struct emuframe, then we need to take care to exit
the frame appropriately. This is done by either rolling back the user PC
to the branch or advancing it to the continuation PC prior to signal
delivery, using dsemul_thread_rollback(). If this were not done then a
sigreturn would return to the struct emuframe, and if that frame had
meanwhile been used in response to an emulated branch instruction within
the signal handler then we would execute the wrong user code.
Whilst a user could theoretically place something like a compact branch
to self in a delay slot and cause their thread to become stuck in an
infinite loop with the frame never being deallocated, this would:
- Only affect the users single process.
- Be architecturally invalid since there would be a branch in the
delay slot, which is forbidden.
- Be extremely unlikely to happen by mistake, and provide a program
with no more ability to harm the system than a simple infinite loop
would.
If a thread requires a delay slot emulation & no frame is available to
it (ie. the process has enough other threads that all frames are
currently in use) then the thread joins a waitqueue. It will sleep until
a frame is freed by another thread in the process.
Since we now know whether a thread has an allocated frame due to our
tracking of its index, the cookie field of struct emuframe is removed as
we can be more certain whether we have a valid frame. Since a thread may
only ever have a single frame at any given time, the epc field of struct
emuframe is also removed & the PC to continue from is instead stored in
struct thread_struct. Together these changes simplify & shrink struct
emuframe somewhat, allowing twice as many frames to fit into the page
allocated for them.
The primary benefit of this patch is that we are now free to mark the
user stack non-executable where that is possible.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: Maciej Rozycki <maciej.rozycki@imgtec.com>
Cc: Faraz Shahbazker <faraz.shahbazker@imgtec.com>
Cc: Raghu Gandham <raghu.gandham@imgtec.com>
Cc: Matthew Fortune <matthew.fortune@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13764/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
(cherry picked from commit 432c6bacbd0c16ec210c43da411ccc3855c4c010)
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
exit_thread() is empty now. Therefore remove it and get rid of a
pointless branch.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
(cherry picked from commit 59a19ea9a0b3b0ee69887b6a5015aee3a3c7e527)
Conflicts:
arch/s390/Kconfig
arch/s390/kernel/process.c
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Avoids function calls to an empty function.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
(cherry picked from commit 04cc89d120f94131de89a6e20da27016db4782ce)
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
start_thread() (called for execve(2)) clears the TIF_USEDFPU flag
without atomically disabling the FPU. With a preemptive kernel, an
unfortunately timed preemption after this could result in another
task (or KVM guest) being scheduled in with the FPU still enabled, since
lose_fpu_inatomic() only turns it off if TIF_USEDFPU is set.
Use lose_fpu(0) instead of the separate FPU / MSA management, which
should do the right thing (drop FPU properly and atomically without
saving state) and will be more future proof.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12302/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
(cherry picked from commit 76e5846d3bdf59eb1010d5607003da2dc3910bb1)
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Per the subject, always select HANDLE_DOMAIN_IRQ, and implement
set_irq_regs() so that it actually works.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12496/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
(cherry picked from commit 1d2753a66acbb101a0ec495cd13b9031ac1b171f)
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Avoid a reader's confusion, as the calculation is correct either way.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12283/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
(cherry picked from commit 036aff91c30a6f15d5bf25f22827abc26b6d06c1)
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Remove irrelevant content from the description of the emulation frame in
`mips_dsemul', referring to bare-metal configurations. Update the text,
reflecting the change made with commit ba3049ed40 ("MIPS: Switch FPU
emulator trap to BREAK instruction."), where we switched from using an
address error exception on an unaligned access to the use of a BREAK 514
instruction causing a breakpoint exception instead.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12176/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
(cherry picked from commit 6e1715f7c34d00dc94f3cecb2526ae3ff0b0649f)
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Emulate the microMIPS ADDIUPC instruction directly in `mips_dsemul'. If
executed in the emulation frame, this instruction produces an incorrect
result, because the value of the PC there is not the same as where the
instruction originated.
Reshape code so as to handle all microMIPS cases together.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12175/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
(cherry picked from commit 69a1e6cbdf1f40d5dcae84c5a538d390b6d2c307)
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Complement commit 102cedc32a ("MIPS: microMIPS: Floating point
support.") which introduced microMIPS FPU emulation, but did not adjust
the encoding of the BREAK instruction used to terminate the branch delay
slot emulation frame. Consequently the execution of any such frame is
indeterminate and, depending on CPU configuration, will result in random
code execution or an offending program being terminated with SIGILL.
This is because the regular MIPS BREAK instruction is encoded with the 0
major and the 0xd minor opcode, however in the microMIPS instruction set
this major/minor opcode pair denotes an encoding reserved for the DSP
ASE. Instead the microMIPS BREAK instruction is encoded with the 0
major and the 0x7 minor opcode.
Use the correct BREAK encoding for microMIPS FPU emulation then.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12174/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
(cherry picked from commit 733b8bc183f491e8263009edf8ef184fb44a6882)
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Correct formatting breakage introduced with commit 102cedc32a ("MIPS:
microMIPS: Floating point support."), so that further changes to this
code can be consistent.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12173/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
(cherry picked from commit a87265cfedce49fa362030ae3e6ef047e08bc12c)
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Fix an issue introduced with commit 9ab4471c9f ("MIPS: math-emu:
Correct delay-slot exception propagation") where the emulation of a NOP
instruction signals the need to terminate the emulation loop. This in
turn, if the PC has not changed from the entry to the loop, will cause
the kernel to terminate the program with SIGILL.
Consider this program:
static double div(double d)
{
do
d /= 2.0;
while (d > .5);
return d;
}
int main(int argc, char **argv)
{
return div(argc);
}
which gets compiled to the following binary code:
00400490 <main>:
400490: 44840000 mtc1 a0,$f0
400494: 3c020040 lui v0,0x40
400498: d44207f8 ldc1 $f2,2040(v0)
40049c: 46800021 cvt.d.w $f0,$f0
4004a0: 46220002 mul.d $f0,$f0,$f2
4004a4: 4620103c c.lt.d $f2,$f0
4004a8: 4501fffd bc1t 4004a0 <main+0x10>
4004ac: 00000000 nop
4004b0: 4620000d trunc.w.d $f0,$f0
4004b4: 03e00008 jr ra
4004b8: 44020000 mfc1 v0,$f0
4004bc: 00000000 nop
Where the FPU emulator is used, depending on the number of command-line
arguments this code will either run to completion or terminate with
SIGILL.
If no arguments are specified, then BC1T will not be taken, NOP will not
be emulated and code will complete successfully.
If one argument is specified, then BC1T will be taken once and NOP will
be emulated. At this point the entry PC value will be 0x400498 and the
new PC value, set by `mips_dsemul' will be 0x4004a0, the target of BC1T.
The emulation loop will terminate, but SIGILL will not be issued,
because the PC has changed. The FPU emulator will be entered again and
on the second execution BC1T will not be taken, NOP will not be emulated
and code will complete successfully.
If two or more arguments are specified, then the first execution of BC1T
will proceed as above. Upon reentering the FPU emulator the emulation
loop will continue to BC1T, at which point the branch will be taken and
NOP emulated again. At this point however the entry PC value will be
0x4004a0, the same as the target of BC1T. This will make the emulator
conclude that execution has not advanced and therefore an unsupported
FPU instruction has been encountered, and SIGILL will be sent to the
process.
Fix the problem by extending the internal API of `mips_dsemul', making
it return -1 if no delay slot emulation frame has been made, the
instruction has been handled and execution of the emulation loop needs
to continue as if nothing happened. Remove code from `mips_dsemul' to
reproduce steps made by the emulation loop at the conclusion of each
iteration, as those will be reached normally now. Adjust call sites
accordingly. Document the API.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12172/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
(cherry picked from commit e4553573b37c3f72533683cb5f3a1ad300b18d37)
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
-----BEGIN PGP SIGNATURE-----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=ViWs
-----END PGP SIGNATURE-----
Merge 4.4.115 into android-4.4
Changes in 4.4.115
loop: fix concurrent lo_open/lo_release
bpf: fix branch pruning logic
x86: bpf_jit: small optimization in emit_bpf_tail_call()
bpf: fix bpf_tail_call() x64 JIT
bpf: introduce BPF_JIT_ALWAYS_ON config
bpf: arsh is not supported in 32 bit alu thus reject it
bpf: avoid false sharing of map refcount with max_entries
bpf: fix divides by zero
bpf: fix 32-bit divide by zero
bpf: reject stores into ctx via st and xadd
x86/pti: Make unpoison of pgd for trusted boot work for real
kaiser: fix intel_bts perf crashes
ALSA: seq: Make ioctls race-free
crypto: aesni - handle zero length dst buffer
crypto: af_alg - whitelist mask and type
power: reset: zx-reboot: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE
gpio: iop: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE
gpio: ath79: add missing MODULE_DESCRIPTION/LICENSE
mtd: nand: denali_pci: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE
igb: Free IRQs when device is hotplugged
KVM: x86: emulator: Return to user-mode on L1 CPL=0 emulation failure
KVM: x86: Don't re-execute instruction when not passing CR2 value
KVM: X86: Fix operand/address-size during instruction decoding
KVM: x86: ioapic: Fix level-triggered EOI and IOAPIC reconfigure race
KVM: x86: ioapic: Clear Remote IRR when entry is switched to edge-triggered
KVM: x86: ioapic: Preserve read-only values in the redirection table
ACPI / bus: Leave modalias empty for devices which are not present
cpufreq: Add Loongson machine dependencies
bcache: check return value of register_shrinker
drm/amdgpu: Fix SDMA load/unload sequence on HWS disabled mode
drm/amdkfd: Fix SDMA ring buffer size calculation
drm/amdkfd: Fix SDMA oversubsription handling
openvswitch: fix the incorrect flow action alloc size
mac80211: fix the update of path metric for RANN frame
btrfs: fix deadlock when writing out space cache
KVM: VMX: Fix rflags cache during vCPU reset
xen-netfront: remove warning when unloading module
nfsd: CLOSE SHOULD return the invalid special stateid for NFSv4.x (x>0)
nfsd: Ensure we check stateid validity in the seqid operation checks
grace: replace BUG_ON by WARN_ONCE in exit_net hook
nfsd: check for use of the closed special stateid
lockd: fix "list_add double add" caused by legacy signal interface
hwmon: (pmbus) Use 64bit math for DIRECT format values
net: ethernet: xilinx: Mark XILINX_LL_TEMAC broken on 64-bit
quota: Check for register_shrinker() failure.
SUNRPC: Allow connect to return EHOSTUNREACH
kmemleak: add scheduling point to kmemleak_scan()
drm/omap: Fix error handling path in 'omap_dmm_probe()'
xfs: ubsan fixes
scsi: aacraid: Prevent crash in case of free interrupt during scsi EH path
scsi: ufs: ufshcd: fix potential NULL pointer dereference in ufshcd_config_vreg
media: usbtv: add a new usbid
usb: gadget: don't dereference g until after it has been null checked
staging: rtl8188eu: Fix incorrect response to SIOCGIWESSID
usb: option: Add support for FS040U modem
USB: serial: pl2303: new device id for Chilitag
USB: cdc-acm: Do not log urb submission errors on disconnect
CDC-ACM: apply quirk for card reader
USB: serial: io_edgeport: fix possible sleep-in-atomic
usbip: prevent bind loops on devices attached to vhci_hcd
usbip: list: don't list devices attached to vhci_hcd
USB: serial: simple: add Motorola Tetra driver
usb: f_fs: Prevent gadget unbind if it is already unbound
usb: uas: unconditionally bring back host after reset
selinux: general protection fault in sock_has_perm
serial: imx: Only wakeup via RTSDEN bit if the system has RTS/CTS
spi: imx: do not access registers while clocks disabled
Linux 4.4.115
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
commit d593574aff0ab846136190b1729c151c736727ec upstream.
Since clocks are disabled except during message transfer clocks
are also disabled when spi_imx_remove gets called. Accessing
registers leads to a freeeze at least on a i.MX 6ULL. Enable
clocks before disabling accessing the MXC_CSPICTRL register.
Fixes: 9e556dcc55 ("spi: spi-imx: only enable the clocks when we start to transfer a message")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38b1f0fb42f772b8c9aac53593883a18ff5eb9d7 upstream.
The wakeup mechanism via RTSDEN bit relies on the system using the RTS/CTS
lines, so only allow such wakeup method when the system actually has
RTS/CTS support.
Fixes: bc85734b12 ("serial: imx: allow waking up on RTSD")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Martin Kaiser <martin@kaiser.cx>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the absence of commit a4298e4522d6 ("net: add SOCK_RCU_FREE socket
flag") and all the associated infrastructure changes to take advantage
of a RCU grace period before freeing, there is a heightened
possibility that a security check is performed while an ill-timed
setsockopt call races in from user space. It then is prudent to null
check sk_security, and if the case, reject the permissions.
Because of the nature of this problem, hard to duplicate, no clear
path, this patch is a simplified band-aid for stable trees lacking the
infrastructure for the series of commits leading up to providing a
suitable RCU grace period. This adjustment is orthogonal to
infrastructure improvements that may nullify the needed check, but
could be added as good code hygiene in all trees.
general protection fault: 0000 [#1] PREEMPT SMP KASAN
CPU: 1 PID: 14233 Comm: syz-executor2 Not tainted 4.4.112-g5f6325b #28
task: ffff8801d1095f00 task.stack: ffff8800b5950000
RIP: 0010:[<ffffffff81b69b7e>] [<ffffffff81b69b7e>] sock_has_perm+0x1fe/0x3e0 security/selinux/hooks.c:4069
RSP: 0018:ffff8800b5957ce0 EFLAGS: 00010202
RAX: dffffc0000000000 RBX: 1ffff10016b2af9f RCX: ffffffff81b69b51
RDX: 0000000000000002 RSI: 0000000000000000 RDI: 0000000000000010
RBP: ffff8800b5957de0 R08: 0000000000000001 R09: 0000000000000001
R10: 0000000000000000 R11: 1ffff10016b2af68 R12: ffff8800b5957db8
R13: 0000000000000000 R14: ffff8800b7259f40 R15: 00000000000000d7
FS: 00007f72f5ae2700(0000) GS:ffff8801db300000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000a2fa38 CR3: 00000001d7980000 CR4: 0000000000160670
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Stack:
ffffffff81b69a1f ffff8800b5957d58 00008000b5957d30 0000000041b58ab3
ffffffff83fc82f2 ffffffff81b69980 0000000000000246 ffff8801d1096770
ffff8801d3165668 ffffffff8157844b ffff8801d1095f00
ffff880000000001
Call Trace:
[<ffffffff81b6a19d>] selinux_socket_setsockopt+0x4d/0x80 security/selinux/hooks.c:4338
[<ffffffff81b4873d>] security_socket_setsockopt+0x7d/0xb0 security/security.c:1257
[<ffffffff82df1ac8>] SYSC_setsockopt net/socket.c:1757 [inline]
[<ffffffff82df1ac8>] SyS_setsockopt+0xe8/0x250 net/socket.c:1746
[<ffffffff83776499>] entry_SYSCALL_64_fastpath+0x16/0x92
Code: c2 42 9b b6 81 be 01 00 00 00 48 c7 c7 a0 cb 2b 84 e8
f7 2f 6d ff 49 8d 7d 10 48 b8 00 00 00 00 00 fc ff df 48 89
fa 48 c1 ea 03 <0f> b6 04 02 84 c0 74 08 3c 03 0f 8e 83 01 00
00 41 8b 75 10 31
RIP [<ffffffff81b69b7e>] sock_has_perm+0x1fe/0x3e0 security/selinux/hooks.c:4069
RSP <ffff8800b5957ce0>
---[ end trace 7b5aaf788fef6174 ]---
Signed-off-by: Mark Salyzyn <salyzyn@android.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: selinux@tycho.nsa.gov
Cc: linux-security-module@vger.kernel.org
Cc: Eric Paris <eparis@parisplace.org>
Cc: Serge E. Hallyn <serge@hallyn.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbeef22fd611c4f47c494b821b2b105b8af970bb upstream.
Quoting Hans:
If we return 1 from our post_reset handler, then our disconnect handler
will be called immediately afterwards. Since pre_reset blocks all scsi
requests our disconnect handler will then hang in the scsi_remove_host
call.
This is esp. bad because our disconnect handler hanging for ever also
stops the USB subsys from enumerating any new USB devices, causes commands
like lsusb to hang, etc.
In practice this happens when unplugging some uas devices because the hub
code may see the device as needing a warm-reset and calls usb_reset_device
before seeing the disconnect. In this case uas_configure_endpoints fails
with -ENODEV. We do not want to print an error for this, so this commit
also silences the shost_printk for -ENODEV.
ENDQUOTE
However, if we do that we better drop any unconditional execution
and report to the SCSI subsystem that we have undergone a reset
but we are not operational now.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce5bf9a50daf2d9078b505aca1cea22e88ecb94a upstream.
Upon usb composition switch there is possibility of ep0 file
release happening after gadget driver bind. In case of composition
switch from adb to a non-adb composition gadget will never gets
bound again resulting into failure of usb device enumeration. Fix
this issue by checking FFS_FL_BOUND flag and avoid extra
gadget driver unbind if it is already done as part of composition
switch.
This fixes adb reconnection error reported on Android running
v4.4 and above kernel versions. Verified on Hikey running vanilla
v4.15-rc7 + few out of tree Mali patches.
Reviewed-at: https://android-review.googlesource.com/#/c/582632/
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg KH <gregkh@linux-foundation.org>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Dmitry Shmidt <dimitrysh@google.com>
Cc: Badhri <badhri@google.com>
Cc: Android Kernel Team <kernel-team@android.com>
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
[AmitP: Cherry-picked it from android-4.14 and updated the commit log]
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef824501f50846589f02173d73ce3fe6021a9d2a upstream.
usbip host lists devices attached to vhci_hcd on the same server
when user does attach over localhost or specifies the server as the
remote.
usbip attach -r localhost -b busid
or
usbip attach -r servername (or server IP)
Fix it to check and not list devices that are attached to vhci_hcd.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef54cf0c600fb8f5737fb001a9e357edda1a1de8 upstream.
usbip host binds to devices attached to vhci_hcd on the same server
when user does attach over localhost or specifies the server as the
remote.
usbip attach -r localhost -b busid
or
usbip attach -r servername (or server IP)
Unbind followed by bind works, however device is left in a bad state with
accesses via the attached busid result in errors and system hangs during
shutdown.
Fix it to check and bail out if the device is already attached to vhci_hcd.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7b8f77872c73f69a16528a9eb87afefcccdc18b upstream.
According to drivers/usb/serial/io_edgeport.c, the driver may sleep
under a spinlock.
The function call path is:
edge_bulk_in_callback (acquire the spinlock)
process_rcvd_data
process_rcvd_status
change_port_settings
send_iosp_ext_cmd
write_cmd_usb
usb_kill_urb --> may sleep
To fix it, the redundant usb_kill_urb() is removed from the error path
after usb_submit_urb() fails.
This possible bug is found by my static analysis tool (DSAC) and checked
by my code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df1cc78a52491f71d8170d513d0f6f114faa1bda upstream.
This devices drops random bytes from messages if you talk to it
too fast.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0386c083c2ce85284dc0b419d7b89c8e567c09f upstream.
When disconnected sometimes the cdc-acm driver logs errors like these:
[20278.039417] cdc_acm 2-2:2.1: urb 9 failed submission with -19
[20278.042924] cdc_acm 2-2:2.1: urb 10 failed submission with -19
[20278.046449] cdc_acm 2-2:2.1: urb 11 failed submission with -19
[20278.049920] cdc_acm 2-2:2.1: urb 12 failed submission with -19
[20278.053442] cdc_acm 2-2:2.1: urb 13 failed submission with -19
[20278.056915] cdc_acm 2-2:2.1: urb 14 failed submission with -19
[20278.060418] cdc_acm 2-2:2.1: urb 15 failed submission with -19
Silence these by not logging errors when the result is -ENODEV.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d08dd3f3dd2ae351b793fc5b76abdbf0fd317b12 upstream.
This adds a new device id for Chilitag devices to the pl2303 driver.
Reported-by: "Chu.Mike [朱堅宜]" <Mike-Chu@prolific.com.tw>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 69341bd15018da0a662847e210f9b2380c71e623 upstream.
FS040U modem is manufactured by omega, and sold by Fujisoft. This patch
adds ID of the modem to use option1 driver. Interface 3 is used as
qmi_wwan, so the interface is ignored.
Signed-off-by: Yoshiaki Okamoto <yokamoto@allied-telesis.co.jp>
Signed-off-by: Hiroyuki Yamamoto <hyamamo@allied-telesis.co.jp>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b77992d2df9e47144354d1b25328b180afa33442 ]
When not associated with an AP, wifi device drivers should respond to the
SIOCGIWESSID ioctl with a zero-length string for the SSID, which is the
behavior expected by dhcpcd.
Currently, this driver returns an error code (-1) from the ioctl call,
which causes dhcpcd to assume that the device is not a wireless interface
and therefore it fails to work correctly with it thereafter.
This problem was reported and tested at
https://github.com/lwfinger/rtl8188eu/issues/234.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b2fc059fa549fe6881d4c1f8d698b0f50bcd16ec ]
Avoid dereferencing pointer g until after g has been sanity null checked;
move the assignment of cdev much later when it is required into a more
local scope.
Detected by CoverityScan, CID#1222135 ("Dereference before null check")
Fixes: b785ea7ce6 ("usb: gadget: composite: fix ep->maxburst initialization")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 04226916d2360f56d57ad00bc48d2d1854d1e0b0 ]
A new usbid of UTV007 is found in a newly bought device.
The usbid is 1f71:3301.
The ID on the chip is:
UTV007
A89029.1
1520L18K1
Both video and audio is tested with the modified usbtv driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 727535903bea924c4f73abb202c4b3e85fff0ca4 ]
_vreg_ is being dereferenced before it is null checked, hence there is a
potential null pointer dereference.
Fix this by moving the pointer dereference after _vreg_ has been null
checked.
This issue was detected with the help of Coccinelle.
Fixes: aa49761309 ("ufs: Add regulator enable support")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e4717292ddebcfe231651b5aff9fa19ca158d178 ]
As part of the scsi EH path, aacraid performs a reinitialization of the
adapter, which encompass freeing resources and IRQs, NULLifying lots of
pointers, and then initialize it all over again. We've identified a
problem during the free IRQ portion of this path if CONFIG_DEBUG_SHIRQ
is enabled on kernel config file.
Happens that, in case this flag was set, right after free_irq()
effectively clears the interrupt, it checks if it was requested as
IRQF_SHARED. In positive case, it performs another call to the IRQ
handler on driver. Problem is: since aacraid currently free some
resources *before* freeing the IRQ, once free_irq() path calls the
handler again (due to CONFIG_DEBUG_SHIRQ), aacraid crashes due to NULL
pointer dereference with the following trace:
aac_src_intr_message+0xf8/0x740 [aacraid]
__free_irq+0x33c/0x4a0
free_irq+0x78/0xb0
aac_free_irq+0x13c/0x150 [aacraid]
aac_reset_adapter+0x2e8/0x970 [aacraid]
aac_eh_reset+0x3a8/0x5d0 [aacraid]
scsi_try_host_reset+0x74/0x180
scsi_eh_ready_devs+0xc70/0x1510
scsi_error_handler+0x624/0xa20
This patch prevents the crash by changing the order of the
deinitialization in this path of aacraid: first we clear the IRQ, then
we free other resources. No functional change intended.
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 22a6c83777ac7c17d6c63891beeeac24cf5da450 ]
Fix some complaints from the UBSAN about signed integer addition overflows.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8677b1ac2db021ab30bb1fa34f1e56ebe0051ec3 ]
If we don't find a matching device node, we must free the memory allocated
in 'omap_dmm' a few lines above.
Fixes: 7cb0d6c17b ("drm/omap: fix TILER on OMAP5")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bde5f6bc68db51128f875a756e9082a6c6ff7b4c ]
kmemleak_scan() will scan struct page for each node and it can be really
large and resulting in a soft lockup. We have seen a soft lockup when
do scan while compile kernel:
watchdog: BUG: soft lockup - CPU#53 stuck for 22s! [bash:10287]
[...]
Call Trace:
kmemleak_scan+0x21a/0x4c0
kmemleak_write+0x312/0x350
full_proxy_write+0x5a/0xa0
__vfs_write+0x33/0x150
vfs_write+0xad/0x1a0
SyS_write+0x52/0xc0
do_syscall_64+0x61/0x1a0
entry_SYSCALL64_slow_path+0x25/0x25
Fix this by adding cond_resched every MAX_SCAN_SIZE.
Link: http://lkml.kernel.org/r/1511439788-20099-1-git-send-email-xieyisheng1@huawei.com
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 88bc0ede8d35edc969350852894dc864a2dc1859 ]
register_shrinker() might return -ENOMEM error since Linux 3.12.
Call panic() as with other failure checks in this function if
register_shrinker() failed.
Fixes: 1d3d4437ea ("vmscan: per-node deferred work")
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Jan Kara <jack@suse.com>
Cc: Michal Hocko <mhocko@suse.com>
Reviewed-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 15bfe05c8d6386f1a90e9340d15336e85e32aad6 ]
On 64-bit (e.g. powerpc64/allmodconfig):
drivers/net/ethernet/xilinx/ll_temac_main.c: In function 'temac_start_xmit_done':
drivers/net/ethernet/xilinx/ll_temac_main.c:633:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
dev_kfree_skb_irq((struct sk_buff *)cur_p->app4);
^
cdmac_bd.app4 is u32, so it is too small to hold a kernel pointer.
Note that several other fields in struct cdmac_bd are also too small to
hold physical addresses on 64-bit platforms.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bd467e4eababe4c04272c1e646f066db02734c79 ]
Power values in the 100s of watt range can easily blow past
32bit math limits when processing everything in microwatts.
Use 64bit math instead to avoid these issues on common 32bit ARM
BMC platforms.
Fixes: 442aba7872 ("hwmon: PMBus device driver")
Signed-off-by: Robert Lippert <rlippert@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 81833de1a46edce9ca20cfe079872ac1c20ef359 ]
restart_grace() uses hardcoded init_net.
It can cause to "list_add double add" in following scenario:
1) nfsd and lockd was started in several net namespaces
2) nfsd in init_net was stopped (lockd was not stopped because
it have users from another net namespaces)
3) lockd got signal, called restart_grace() -> set_grace_period()
and enabled lock_manager in hardcoded init_net.
4) nfsd in init_net is started again,
its lockd_up() calls set_grace_period() and tries to add
lock_manager into init_net 2nd time.
Jeff Layton suggest:
"Make it safe to call locks_start_grace multiple times on the same
lock_manager. If it's already on the global grace_list, then don't try
to add it again. (But we don't intentionally add twice, so for now we
WARN about that case.)
With this change, we also need to ensure that the nfsd4 lock manager
initializes the list before we call locks_start_grace. While we're at
it, move the rest of the nfsd_net initialization into
nfs4_state_create_net. I see no reason to have it spread over two
functions like it is today."
Suggested patch was updated to generate warning in described situation.
Suggested-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ae254dac721d44c0bfebe2795df87459e2e88219 ]
Prevent the use of the closed (invalid) special stateid by clients.
Signed-off-by: Andrew Elble <aweits@rit.edu>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9271d7e509c1bfc0b9a418caec29ec8d1ac38270 ]
After taking the stateid st_mutex, we want to know that the stateid
still represents valid state before performing any non-idempotent
actions.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5b5971df3bc2775107ddad164018a8a8db633b81 ]
v2:
* Replace busy wait with wait_event()/wake_up_all()
* Cannot garantee that at the time xennet_remove is called, the
xen_netback state will not be XenbusStateClosed, so added a
condition for that
* There's a small chance for the xen_netback state is
XenbusStateUnknown by the time the xen_netfront switches to Closed,
so added a condition for that.
When unloading module xen_netfront from guest, dmesg would output
warning messages like below:
[ 105.236836] xen:grant_table: WARNING: g.e. 0x903 still in use!
[ 105.236839] deferring g.e. 0x903 (pfn 0x35805)
This problem relies on netfront and netback being out of sync. By the time
netfront revokes the g.e.'s netback didn't have enough time to free all of
them, hence displaying the warnings on dmesg.
The trick here is to make netfront to wait until netback frees all the g.e.'s
and only then continue to cleanup for the module removal, and this is done by
manipulating both device states.
Signed-off-by: Eduardo Otubo <otubo@redhat.com>
Acked-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c37c28730bb031cc8a44a130c2555c0f3efbe2d0 ]
Reported by syzkaller:
*** Guest State ***
CR0: actual=0x0000000080010031, shadow=0x0000000060000010, gh_mask=fffffffffffffff7
CR4: actual=0x0000000000002061, shadow=0x0000000000000000, gh_mask=ffffffffffffe8f1
CR3 = 0x000000002081e000
RSP = 0x000000000000fffa RIP = 0x0000000000000000
RFLAGS=0x00023000 DR7 = 0x00000000000000
^^^^^^^^^^
------------[ cut here ]------------
WARNING: CPU: 6 PID: 24431 at /home/kernel/linux/arch/x86/kvm//x86.c:7302 kvm_arch_vcpu_ioctl_run+0x651/0x2ea0 [kvm]
CPU: 6 PID: 24431 Comm: reprotest Tainted: G W OE 4.14.0+ #26
RIP: 0010:kvm_arch_vcpu_ioctl_run+0x651/0x2ea0 [kvm]
RSP: 0018:ffff880291d179e0 EFLAGS: 00010202
Call Trace:
kvm_vcpu_ioctl+0x479/0x880 [kvm]
do_vfs_ioctl+0x142/0x9a0
SyS_ioctl+0x74/0x80
entry_SYSCALL_64_fastpath+0x23/0x9a
The failed vmentry is triggered by the following beautified testcase:
#include <unistd.h>
#include <sys/syscall.h>
#include <string.h>
#include <stdint.h>
#include <linux/kvm.h>
#include <fcntl.h>
#include <sys/ioctl.h>
long r[5];
int main()
{
struct kvm_debugregs dr = { 0 };
r[2] = open("/dev/kvm", O_RDONLY);
r[3] = ioctl(r[2], KVM_CREATE_VM, 0);
r[4] = ioctl(r[3], KVM_CREATE_VCPU, 7);
struct kvm_guest_debug debug = {
.control = 0xf0403,
.arch = {
.debugreg[6] = 0x2,
.debugreg[7] = 0x2
}
};
ioctl(r[4], KVM_SET_GUEST_DEBUG, &debug);
ioctl(r[4], KVM_RUN, 0);
}
which testcase tries to setup the processor specific debug
registers and configure vCPU for handling guest debug events through
KVM_SET_GUEST_DEBUG. The KVM_SET_GUEST_DEBUG ioctl will get and set
rflags in order to set TF bit if single step is needed. All regs' caches
are reset to avail and GUEST_RFLAGS vmcs field is reset to 0x2 during vCPU
reset. However, the cache of rflags is not reset during vCPU reset. The
function vmx_get_rflags() returns an unreset rflags cache value since
the cache is marked avail, it is 0 after boot. Vmentry fails if the
rflags reserved bit 1 is 0.
This patch fixes it by resetting both the GUEST_RFLAGS vmcs field and
its cache to 0x2 during vCPU reset.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Tested-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b77000ed558daa3bef0899d29bf171b8c9b5e6a8 ]
If we fail to prepare our pages for whatever reason (out of memory in
our case) we need to make sure to drop the block_group->data_rwsem,
otherwise hilarity ensues.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ add label and use existing unlocking code ]
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
