[ Upstream commit 67793bd3b3948dc8c8384b6430e036a30a0ecb43 ]
The driver currently sets register 0xfb (Low Refresh Rate) based on the
value of mode->vrefresh. Firstly, this field is specified to be in Hz,
but the magic numbers used by the code are Hz * 1000. This essentially
leads to the low refresh rate always being set to 0x01, since the
vrefresh value will always be less than 24000. Fix the magic numbers to
be in Hz.
Secondly, according to the comment in drm_modes.h, the field is not
supposed to be used in a functional way anyway. Instead, use the helper
function drm_mode_vrefresh().
Fixes: 9c8af882bf ("drm: Add adv7511 encoder driver")
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Matt Redfearn <matt.redfearn@thinci.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190424132210.26338-1-matt.redfearn@thinci.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f3417569165a8ee57654217f73e0160312f409c ]
The bridge loses its hw state when the cable is unplugged. If we detect
this case in the hpd handler, reset its state.
Reported-by: Rob Clark <robdclark@gmail.com>
Tested-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180703165648.120401-1-seanpaul@chromium.org
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3587c856675c45809010c2cee5b21096f6e8e938 upstream.
I've found that by just turning the chip on and off via the
POWER_DOWN register, I end up getting i2c_transfer errors on
HiKey.
Investigating further, it turns out that some of the register
state in hardware is getting lost, as the device registers are
reset when the chip is powered down.
Thus this patch simply re-writes the i2c address to the
ADV7511_REG_EDID_I2C_ADDR register to ensure its properly set
before we try to read the EDID data.
Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1484614372-15342-7-git-send-email-john.stultz@linaro.org
Signed-off-by: Thong Ho <thong.ho.px@rvc.renesas.com>
Signed-off-by: Nhan Nguyen <nhan.nguyen.yb@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d5104c5a6b56385426e15047050584794bb6254 upstream.
In chasing down a previous issue with EDID probing from calling
drm_helper_hpd_irq_event() from irq context, Laurent noticed
that the DRM documentation suggests that
drm_kms_helper_hotplug_event() should be used instead.
Thus this patch replaces drm_helper_hpd_irq_event() with
drm_kms_helper_hotplug_event(), which requires we update the
connector.status entry and only call _hotplug_event() when the
status changes.
Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1484614372-15342-3-git-send-email-john.stultz@linaro.org
Signed-off-by: Thong Ho <thong.ho.px@rvc.renesas.com>
Signed-off-by: Nhan Nguyen <nhan.nguyen.yb@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 518cb7057a59b9441336d2e88a396d52b6ab0cce upstream.
I was recently seeing issues with EDID probing, where
the logic to wait for the EDID read bit to be set by the
IRQ wasn't happening and the code would time out and fail.
Digging deeper, I found this was due to the fact that
IRQs were disabled as we were running in IRQ context from
the HPD signal.
Thus this patch changes the logic to handle the HPD signal
via a work_struct so we can be out of irq context.
With this patch, the EDID probing on hotplug does not time
out.
Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1484614372-15342-2-git-send-email-john.stultz@linaro.org
Signed-off-by: Thong Ho <thong.ho.px@rvc.renesas.com>
Signed-off-by: Nhan Nguyen <nhan.nguyen.yb@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0bfcc22d9822947b0ad3095e8363eab5261864c upstream.
When the adv7511 i2c client doesn't have an interrupt line, we observe a
deadlock on caused by trying to lock drm device's mode_config.mutex twice
in the same context.
Here is the sequence that causes it:
ioctl DRM_IOCTL_MODE_GETCONNECTOR from userspace
drm_mode_getconnector (acquires mode_config mutex)
connector->fill_modes()
drm_helper_probe_single_connector_modes
connector_funcs->get_modes
adv7511_encoder_get_modes
adv7511_get_edid_block
adv7511_irq_process
drm_helper_hpd_irq_event (acquires mode_config mutex again)
In adv7511_irq_process, don't call drm_helper_hpd_irq_event when not
called from the interrupt handler. It doesn't serve any purpose there
anyway.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Thong Ho <thong.ho.px@rvc.renesas.com>
Signed-off-by: Nhan Nguyen <nhan.nguyen.yb@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0be8584b01160eb6f49e77f8e9c1da286bb4ffb upstream.
The interrupts for EDID_READY or DDC_ERROR were never enabled in this
driver, so reading EDID always timed out when chip was powered down and
interrupts were used. Fix this and also remove clearing the interrupt
flags, they are cleared in POWER_DOWN mode anyhow (unlike the interrupt
enable flags) according to docs and my tests.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Thong Ho <thong.ho.px@rvc.renesas.com>
Signed-off-by: Nhan Nguyen <nhan.nguyen.yb@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* removes the now unused DRM slave encoder support, which all users have
migrated away from, allowing us to simplify the code.
* ensure all pending interrupts are processed together, rather than
needing the handler to be re-entered each time.
* use more HDMI helpers to setup the info frames.
* fix EDID read handling by ensuring that we always wait the specified time
before attempting to read the EDID, no matter where the EDID read request
came from.
* 'drm-tda998x-devel' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm/i2c: tda998x: clean up after struct tda998x_priv2 removal
drm/i2c: tda998x: kill struct tda998x_priv2
drm/i2c: tda998x: move connector into struct tda998x_priv
drm/i2c: tda998x: remove encoder pointer
drm/i2c: tda998x: remove DRM slave encoder support
drm/i2c: tda998x: use more HDMI helpers
drm/i2c: tda998x: handle all outstanding interrupts
drm/i2c: tda998x: convert to u8/u16/u32 types
drm/i2c: tda998x: re-implement "Fix EDID read timeout on HDMI connect"
drm/i2c: tda998x: report whether we actually handled the IRQ
drm/i2c: tda998x: remove useless NULL checks
We can now kill a number of glue functions which were sitting between
the common tda998x code and the drm encoder/connector methods. This
results in slightly cleaner code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Kill the redundant tda998x_priv2 structure now that its only member is
the struct tda998x_priv.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the encoder pointer from struct tda998x_priv, moving the encoder
itself from struct tda998x_priv2 here.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the DRM slave encoder compatibility from the TDA998x driver. We
now use the component helpers to manage the binding of DRM sub-drivers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJV/yX5AAoJEHm+PkMAQRiGUc4IAIFtSt2EORex45d2c64Varjm
4wVJM6k1xz0e8c5bI5D03y/WaefIC2LlKHtWw4+TytnwWEryuGQ1IitvDPZLIntk
I2tUN1IzyxZrJcG2GyfozjxSxeIcaL7us5j7555kEaRVWMamqDaQgVgEKFRqD43N
M4y8qRUeU3OiaL3OhQ9beSfpI/XqjaT+ECGO5HKC3NOJtTrD+cFqLAG9ScCPhvtk
YrrXx3K6J3mylvdvJ5W6JlxOrhFMO+YzViy2bRY8OnAR2vD88p61eT8V2+ENbnMj
+AqXS4HOBpJ6I1Qhff99r0YyvVT/ln9dW7qLAXK3WG27z6HOSWr8KWNUyQD2VLE=
=9yBb
-----END PGP SIGNATURE-----
Merge tag 'v4.3-rc2' into topic/drm-misc
Backmerge Linux 4.3-rc2 because of conflicts in the dp helper code
between bugfixes and new code. Just adjacent lines really.
On top of that there's a silent conflict in the new fsl-dcu driver
merged into 4.3 and
commit 844f9111f6
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Wed Sep 2 10:42:40 2015 +0200
drm/atomic: Make prepare_fb/cleanup_fb only take state, v3.
which Thierry Reding spotted and provided a fixup for.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
As reading the interrupt registers clears the outstanding interrupts, we
must process all received interrupts to avoid dropping any. Rearrange
the code to achieve this, and properly check for a HPD interrupt from
the CEC_RXSHPDINT register.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
C99 types are against the style of the Linux kernel. Convert to using
Linus-friendly types. See https://lwn.net/Articles/113367/ for more
information.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 6833d26ef8 ("drm: tda998x: Fix EDID read timeout on HDMI
connect") used a weak scheme to try and delay reading EDID on a HDMI
connect event. It is weak because delaying the notification of a
hotplug event does not stop userspace from trying to read the EDID
within the 100ms delay.
The solution provided here solves this issue:
* When a HDMI connection event is detected, mark a blocking flag for
EDID reads, and start a timer for the delay.
* If an EDID read is attempted, and the blocking flag is set, wait
for the blocking flag to clear.
* When the timer expires, clear the blocking flag and wake any thread
waiting for the EDID read.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than always reporting that the interrupt was handled, we should
report whether we did handle the interrupt. Arrange to report IRQ_NONE
for cases where we found nothing to do.
This allows us to (eventually) recover from stuck-IRQ problems, rather
than causing the kernel to solidly lock up.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is no way 'priv' can be NULL in tda998x_irq_thread() - this can
only happen if request_threaded_irq() was passed a NULL priv pointer,
and we would have crashed long before then if that was the case.
We also always ensure that priv->encoder is correctly setup, which
must have been initialised prior to the interrupt being claimed, so we
can remove this check as well.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull TDA998x i2c driver fixes from Russell King:
"This fixes the double-checksumming of the AVI infoframe which was
resulting in the checksum always being zero. It went unnoticed as
none of my HDMI devices had a problem with this"
[ Pulling directly from rmk since Dave Airlie is on vacation - Linus ]
* 'drm-tda998x-fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm/i2c: tda998x: fix bad checksum of the HDMI AVI infoframe
The commit 8c7a075da9
"drm/i2c: tda998x: use drm_hdmi_avi_infoframe_from_display_mode()"
also uses hdmi_avi_infoframe_pack() to create the AVI infoframe.
This function sets the checksum of the frame and this breaks
the second calculation of the checksum done in tda998x_write_if().
Fixes: 8c7a075da9 ("drm/i2c: tda998x: use drm_hdmi_avi_infoframe_from_display_mode()")
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Separate the functionality using sequences of register writes from the
functions that take register defaults. This change renames the arguments
in order to support the extension of reg_sequence to take an optional
delay to be applied after any given register in a sequence is written.
This avoids adding an int to all register defaults, which could
substantially increase memory usage for regmaps with large default tables.
This also updates all the clients of multi_reg_write/register_patch.
Signed-off-by: Nariman Poushin <nariman@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ADV7511 is probed before its slave encoder init function associates
it with an encoder. This creates a time window during which hot plug
detection interrupts can occur with an encoder, resulting in a crash in
the IRQ handler.
Fix this by ignoring hot plug detection IRQs when no encoder is
associated yet.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Stephen Rothwell reports that he sees a compiler warning on x86_64:
drivers/gpu/drm/i2c/tda998x_drv.c: In function 'tda998x_write_avi':
drivers/gpu/drm/i2c/tda998x_drv.c:647:3: warning: format '%d' expects argument of type 'int', but argument 3 has type 'ssize_t' [-Wformat=]
dev_err(&priv->hdmi->dev, "hdmi_avi_infoframe_pack() failed: %d\n", len);
^
Fix this by using the appropriate length modifier.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
tda998x: use helpers for infoframe.
* 'drm-tda998x-devel' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm/i2c: tda998x: use drm_hdmi_avi_infoframe_from_display_mode()
Make use of the DRM HDMI AVI infoframe helper to construct the AVI
infoframe, rather than coding this up ourselves. This allows DRM
to supply proper aspect ratio information derived from the DRM
display mode structure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the internal dependency on DPMS mode for power management by
using a by a powered state boolean instead, and use the new power off
handler at probe time. This ensure that the regmap cache is properly
marked as dirty when the device is probed, and the registers properly
synced during the first power up.
As a side effect this removes the initialization of current_edid_segment
at probe time, as the field will be initialized when the device is
powered on, at the latest right before reading EDID data.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Christian Kohn <christian.kohn@xilinx.com>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
The EDID read code waits for the read completion interrupt to occur
using wait_event_interruptible(). The condition passed to the macro
reads I2C registers. This results in sleeping with the task state set
to TASK_INTERRUPTIBLE, triggering a WARN_ON() introduced in commit
8eb23b9f35 ("sched: Debug nested sleeps").
Fix this by reworking the EDID read code. Instead of checking whether
the read is complete through I2C reads, handle the interrupt registers
in the interrupt handler and update a new edid_read flag accordingly. As
a side effect both the IRQ and polling code paths now process the
interrupt sources through the same code path, simplifying the code.
Cc: stable@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The DDC error interrupt bit is located in REG_INT1, not REG_INT0. Update
both the interrupt wait code and the interrupt sources reset code
accordingly.
Cc: stable@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Change 'pixes' to 'pixels'
Change 'enabel' to 'enable'
Change 'enabeling' to 'enabling'
Signed-off-by: Yannick Guerrini <yguerrini@tomshardware.fr>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A number of TDA998x updates for the next merge window. Patches
included in this set are:
* adding support for finding the attached CRTCs from DT
* a fix function name mis-spelling in a dev_err()
* simplify the EDID reading by using the drm_do_get_edid() function
instead of coding this ourselves.
* 'drm-tda998x-devel' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm/i2c: tda998x: use drm_do_get_edid()
drm/i2c: tda998x: fix misspelling of current function in string
drm/i2c: tda998x: add OF support for finding attached CRTCs
This backmerges drm-fixes into drm-next mainly for the amdkfd
stuff, I'm not 100% confident, but it builds and the amdkfd
folks can fix anything up.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Conflicts:
drivers/gpu/drm/amd/amdkfd/kfd_device_queue_manager.c
drivers/gpu/drm/amd/amdkfd/kfd_device_queue_manager.h
3 fixes for the tda998x.
* 'drm-tda998x-fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm/i2c: tda998x: set the CEC I2C address based on the slave I2C address
drm: tda998x: Fix EDID read timeout on HDMI connect
drm: tda998x: Protect the page register
Replace the internal EDID read implementation by a call to the new EDID
read core function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Tested-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Replace a misspelled function name by %s and then __func__.
This was done using Coccinelle, including the use of Levenshtein distance,
as proposed by Rasmus Villemoes.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The I2C address for the TDA9989 and TDA19989 is fixed at 0x34 but the
two LSBs of the TDA19988's address are set by two configuration pins
on the chip. Irrespective of the chip, the associated CEC peripheral's
I2C address is based upon the main I2C address.
This patch avoids any special handling required to support systems that
contain multiple TDA19988 devices on the same I2C bus.
Signed-off-by: Andrew Jackson <Andrew.Jackson@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ADV7511 supports interlaced modes fine, there's no need to reject
them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
When the HDMI cable is disconnected and reconnected, EDID reading
is called too early raising a EDID read timeout.
This patch uses the system work queue to delay the notification
of the HDMI connect/disconnect event.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As the HDMI registers of the TDA998x chips are accessed by pages,
the page register must be protected.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a driver for the Analog Devices adv7511. The adv7511 is
a standalone HDMI transmitter chip. It features a HDMI output interface
on one end and video and audio input interfaces on the other.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
This builds upon the previous set of fixes which were pulled on 6th July.
Included in this set are:
- an update from Jean-Francois to add the missing reg documentation entry
to the device tree documentation.
- conversion of the tda998x driver to the component helpers.
* 'tda998x-devel' of git://ftp.arm.linux.org.uk/~rmk/linux-cubox:
drm/i2c: tda998x: add component support
drm/i2c: tda998x: allow re-use of tda998x support code
drm/i2c: tda998x: fix lack of required reg in DT documentation
Conflicts:
drivers/gpu/drm/i2c/tda998x_drv.c
Add component helper support to the tda998x driver. This permits the
TDA998x to be declared as a separate device in device tree, and bound
at the appropriate moment with a co-operating card driver.
The existing slave_encoder interfaces are kept while there are existing
users of it in order to prevent regressions.
Tested-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Re-jig the TDA998x code so that we separate the functionality from the
drm slave encoder implementation. In several places, this is pretty
clearly the correct thing to do, because we can avoid repetitively
having to convert from the drm_encoder to the TDA998x private
structure, particularly with the driver internal functions.
The main motivation behind this change is to allow the code to be
re-used with a standard drm_encoder and drm_connector implementation
based on the component helpers, rather than the slave_encoder system.
The addition of this will be in the following patch.
We keep the slave_encoder interface as there are existing users of
this; we need to give them time to convert and test.
Tested-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
