commit 303911cfc5b95d33687d9046133ff184cf5043ff upstream.
The syzbot fuzzer has found two (!) races in the USB character device
registration and deregistration routines. This patch fixes the races.
The first race results from the fact that usb_deregister_dev() sets
usb_minors[intf->minor] to NULL before calling device_destroy() on the
class device. This leaves a window during which another thread can
allocate the same minor number but will encounter a duplicate name
error when it tries to register its own class device. A typical error
message in the system log would look like:
sysfs: cannot create duplicate filename '/class/usbmisc/ldusb0'
The patch fixes this race by destroying the class device first.
The second race is in usb_register_dev(). When that routine runs, it
first allocates a minor number, then drops minor_rwsem, and then
creates the class device. If the device creation fails, the minor
number is deallocated and the whole routine returns an error. But
during the time while minor_rwsem was dropped, there is a window in
which the minor number is allocated and so another thread can
successfully open the device file. Typically this results in
use-after-free errors or invalid accesses when the other thread closes
its open file reference, because the kernel then tries to release
resources that were already deallocated when usb_register_dev()
failed. The patch fixes this race by keeping minor_rwsem locked
throughout the entire routine.
Reported-and-tested-by: syzbot+30cf45ebfe0b0c4847a1@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1908121607590.1659-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 561759292774707b71ee61aecc07724905bb7ef1 ]
If the device rejects the control transfer to enable device-initiated
U1/U2 entry, then the device will not initiate U1/U2 transition. To
improve the performance, the downstream port should not initate
transition to U1/U2 to avoid the delay from the device link command
response (no packet can be transmitted while waiting for a response from
the device). If the device has some quirks and does not implement U1/U2,
it may reject all the link state change requests, and the downstream
port may resend and flood the bus with more requests. This will affect
the device performance even further. This patch disables the
hub-initated U1/U2 if the device-initiated U1/U2 entry fails.
Reference: USB 3.2 spec 7.2.4.2.3
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e244c4699f859cf7149b0781b1894c7996a8a1df upstream.
With Link Power Management (LPM) enabled USB3 links transition to low
power U1/U2 link states from U0 state automatically.
Current hub code detects USB3 remote wakeups by checking if the software
state still shows suspended, but the link has transitioned from suspended
U3 to enabled U0 state.
As it takes some time before the hub thread reads the port link state
after a USB3 wake notification, the link may have transitioned from U0
to U1/U2, and wake is not detected by hub code.
Fix this by handling U1/U2 states in the same way as U0 in USB3 wakeup
handling
This patch should be added to stable kernels since 4.13 where LPM was
kept enabled during suspend/resume
Cc: <stable@vger.kernel.org> # v4.13+
Signed-off-by: Lee, Chiasheng <chiasheng.lee@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd21f0222adab64974b7d1b4b8c7ce6b23e9ea4d upstream.
This patch fixes the chipmunk-like voice that manifets randomly when
using the integrated mic of the Logitech Webcam HD C270.
The issue was solved initially for this device by commit 2394d67e44
("USB: add RESET_RESUME for webcams shown to be quirky") but it was then
reintroduced by e387ef5c47 ("usb: Add USB_QUIRK_RESET_RESUME for all
Logitech UVC webcams"). This patch is to have the fix back.
Signed-off-by: Marco Zatta <marco@zatta.me>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea261113385ac0a71c2838185f39e8452d54b152 upstream.
Without USB_QUIRK_NO_LPM ethernet will not work and rtl8152 will
complain with
r8152 <device...>: Stop submitting intr, status -71
Adding the quirk resolves this. As the dock is externally powered, this
should not have any drawbacks.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a03ff54460817c76105f81f3aa8ef655759ccc9a upstream.
The syzkaller USB fuzzer found a slab-out-of-bounds write bug in the
USB core, caused by a failure to check the actual size of a BOS
descriptor. This patch adds a check to make sure the descriptor is at
least as large as it is supposed to be, so that the code doesn't
inadvertently access memory beyond the end of the allocated region
when assigning to dev->bos->desc->bNumDeviceCaps later on.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+71f1e64501a309fcc012@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8ead7e817224d7832fe51a19783cb8fcadc79467 ]
If ohci-platform is runtime suspended, we can currently get an "imprecise
external abort" on reboot with ohci-platform loaded when PM runtime
is implemented for the SoC.
Let's fix this by adding PM runtime support to usb_hcd_platform_shutdown.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 381419fa720060ba48b7bbc483be787d5b1dca6f ]
The SCSI core does not like to have devices or hosts unregistered
while error recovery is in progress. Trying to do so can lead to
self-deadlock: Part of the removal code tries to obtain a lock already
held by the error handler.
This can cause problems for the usb-storage and uas drivers, because
their error handler routines perform a USB reset, and if the reset
fails then the USB core automatically goes on to unbind all drivers
from the device's interfaces -- all while still in the context of the
SCSI error handler.
As it turns out, practically all the scenarios leading to a USB reset
failure end up causing a device disconnect (the main error pathway in
usb_reset_and_verify_device(), at the end of the routine, calls
hub_port_logical_disconnect() before returning). As a result, the
hub_wq thread will soon become aware of the problem and will unbind
all the device's drivers in its own context, not in the
error-handler's context.
This means that usb_reset_device() does not need to call
usb_unbind_and_rebind_marked_interfaces() in cases where
usb_reset_and_verify_device() has returned an error, because hub_wq
will take care of everything anyway.
This particular problem was observed in somewhat artificial
circumstances, by using usbfs to tell a hub to power-down a port
connected to a USB-3 mass storage device using the UAS protocol. With
the port turned off, the currently executing command timed out and the
error handler started running. The USB reset naturally failed,
because the hub port was off, and the error handler deadlocked as
described above. Not carrying out the call to
usb_unbind_and_rebind_marked_interfaces() fixes this issue.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Kento Kobayashi <Kento.A.Kobayashi@sony.com>
Tested-by: Kento Kobayashi <Kento.A.Kobayashi@sony.com>
CC: Bart Van Assche <bvanassche@acm.org>
CC: Martin K. Petersen <martin.petersen@oracle.com>
CC: Jacky Cao <Jacky.Cao@sony.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c2b71462d294cf517a0bc6e4fd6424d7cee5596f upstream.
The syzkaller fuzzer reported a bug in the USB hub driver which turned
out to be caused by a negative runtime-PM usage counter. This allowed
a hub to be runtime suspended at a time when the driver did not expect
it. The symptom is a WARNING issued because the hub's status URB is
submitted while it is already active:
URB 0000000031fb463e submitted while active
WARNING: CPU: 0 PID: 2917 at drivers/usb/core/urb.c:363
The negative runtime-PM usage count was caused by an unfortunate
design decision made when runtime PM was first implemented for USB.
At that time, USB class drivers were allowed to unbind from their
interfaces without balancing the usage counter (i.e., leaving it with
a positive count). The core code would take care of setting the
counter back to 0 before allowing another driver to bind to the
interface.
Later on when runtime PM was implemented for the entire kernel, the
opposite decision was made: Drivers were required to balance their
runtime-PM get and put calls. In order to maintain backward
compatibility, however, the USB subsystem adapted to the new
implementation by keeping an independent usage counter for each
interface and using it to automatically adjust the normal usage
counter back to 0 whenever a driver was unbound.
This approach involves duplicating information, but what is worse, it
doesn't work properly in cases where a USB class driver delays
decrementing the usage counter until after the driver's disconnect()
routine has returned and the counter has been adjusted back to 0.
Doing so would cause the usage counter to become negative. There's
even a warning about this in the USB power management documentation!
As it happens, this is exactly what the hub driver does. The
kick_hub_wq() routine increments the runtime-PM usage counter, and the
corresponding decrement is carried out by hub_event() in the context
of the hub_wq work-queue thread. This work routine may sometimes run
after the driver has been unbound from its interface, and when it does
it causes the usage counter to go negative.
It is not possible for hub_disconnect() to wait for a pending
hub_event() call to finish, because hub_disconnect() is called with
the device lock held and hub_event() acquires that lock. The only
feasible fix is to reverse the original design decision: remove the
duplicate interface-specific usage counter and require USB drivers to
balance their runtime PM gets and puts. As far as I know, all
existing drivers currently do this.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+7634edaea4d0b341c625@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c01c348ecdc66085e44912c97368809612231520 upstream.
Some drivers (such as the vub300 MMC driver) expect usb_string() to
return a properly NUL-terminated string, even when an error occurs.
(In fact, vub300's probe routine doesn't bother to check the return
code from usb_string().) When the driver goes on to use an
unterminated string, it leads to kernel errors such as
stack-out-of-bounds, as found by the syzkaller USB fuzzer.
An out-of-range string index argument is not at all unlikely, given
that some devices don't provide string descriptors and therefore list
0 as the value for their string indexes. This patch makes
usb_string() return a properly terminated empty string along with the
-EINVAL error code when an out-of-range index is encountered.
And since a USB string index is a single-byte value, indexes >= 256
are just as invalid as values of 0 or below.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+b75b85111c10b8d680f1@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d7a6c0ce8d26412903c7981503bad9e1cc7c45d2 upstream.
USB Bluetooth controller QCA ROME (0cf3:e007) sometimes stops working
after S3:
[ 165.110742] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[ 168.432065] Bluetooth: hci0: Failed to send body at 4 of 1953 (-110)
After some experiments, I found that disabling LPM can workaround the
issue.
On some platforms, the USB power is cut during S3, so the driver uses
reset-resume to resume the device. During port resume, LPM gets enabled
twice, by usb_reset_and_verify_device() and usb_port_resume().
Consolidate all checks into new LPM helpers to make sure LPM only gets
enabled once.
Fixes: de68bab4fa ("usb: Don't enable USB 2.0 Link PM by default.”)
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org> # after much soaking
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7529b2574a7aaf902f1f8159fbc2a7caa74be559 upstream.
Use new helpers to make LPM enabling/disabling more clear.
This is a preparation to subsequent patch.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org> # after much soaking
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32fd87b3bbf5f7a045546401dfe2894dbbf4d8c3 upstream.
When cleaning up the configurations, make sure we only free the number
of configurations and interfaces that we could have allocated.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e86108940e541febf35813402ff29fa6f4a9ac0b ]
When initializing a hub we want to give a USB3 port in link training
the same debounce delay time before autosuspening the hub as already
trained, connected enabled ports.
USB3 ports won't reach the enabled state with "current connect status" and
"connect status change" bits set until the USB3 link training finishes.
Catching the port in link training (polling) and adding the debounce delay
prevents unnecessary failed attempts to autosuspend the hub.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3483254b89438e60f719937376c5e0ce2bc46761 upstream.
To match the Corsair Strafe RGB, the Corsair K70 RGB also requires
USB_QUIRK_DELAY_CTRL_MSG to completely resolve boot connection issues
discussed here: https://github.com/ckb-next/ckb-next/issues/42.
Otherwise roughly 1 in 10 boots the keyboard will fail to be detected.
Patch that applied delay control quirk for Corsair Strafe RGB:
cb88a0588717 ("usb: quirks: add control message delay for 1b1c:1b20")
Previous K70 RGB patch to add delay-init quirk:
7a1646d92257 ("Add delay-init quirk for Corsair K70 RGB keyboards")
Signed-off-by: Jack Stocker <jackstocker.93@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 704620afc70cf47abb9d6a1a57f3825d2bca49cf upstream.
When reading an extra descriptor, we need to properly check the minimum
and maximum size allowed, to prevent from invalid data being sent by a
device.
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Co-developed-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Hui Peng <benquike@gmail.com>
Signed-off-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f2dde6ba89b1ef1fe23c1138131b315d9aa4019 upstream.
Some lower volume SanDisk Ultra Flair in 16GB, which the VID:PID is
in 0781:5591, will aggressively request LPM of U1/U2 during runtime,
when using this thumb drive as the OS installation key we found the
device will generate failure during U1 exit path making it dropped
from the USB bus, this causes a corrupted installation in system at
the end.
i.e.,
[ 166.918296] hub 2-0:1.0: state 7 ports 7 chg 0000 evt 0004
[ 166.918327] usb usb2-port2: link state change
[ 166.918337] usb usb2-port2: do warm reset
[ 166.970039] usb usb2-port2: not warm reset yet, waiting 50ms
[ 167.022040] usb usb2-port2: not warm reset yet, waiting 200ms
[ 167.276043] usb usb2-port2: status 02c0, change 0041, 5.0 Gb/s
[ 167.276050] usb 2-2: USB disconnect, device number 2
[ 167.276058] usb 2-2: unregistering device
[ 167.276060] usb 2-2: unregistering interface 2-2:1.0
[ 167.276170] xhci_hcd 0000:00:15.0: shutdown urb ffffa3c7cc695cc0 ep1in-bulk
[ 167.284055] sd 0:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 167.284064] sd 0:0:0:0: [sda] tag#0 CDB: Read(10) 28 00 00 33 04 90 00 01 00 00
...
Analyzed the USB trace in the link layer we realized it is because
of the 6-ms timer of tRecoveryConfigurationTimeout which documented
on the USB 3.2 Revision 1.0, the section 7.5.10.4.2 of "Exit from
Recovery.Configuration"; device initiates U1 exit -> Recovery.Active
-> Recovery.Configuration, then the host timer timeout makes the link
transits to eSS.Inactive -> Rx.Detect follows by a Warm Reset.
Interestingly, the other higher volume of SanDisk Ultra Flair sharing
the same VID:PID, such as 64GB, would not request LPM during runtime,
it sticks at U0 always, thus disabling LPM does not affect those thumb
drives at all.
The same odd occures in SanDisk Ultra Fit 16GB, VID:PID in 0781:5583.
Signed-off-by: Harry Pan <harry.pan@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit effd14f66cc1ef6701a19c5a56e39c35f4d395a5 upstream.
Cherry G230 Stream 2.0 (G85-231) and 3.0 (G85-232) need this quirk to
function correctly. This fixes a but where double pressing numlock locks
up the device completely with need to replug the keyboard.
Signed-off-by: Michael Niewöhner <linux@mniewoehner.de>
Tested-by: Michael Niewöhner <linux@mniewoehner.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22454b79e6de05fa61a2a72d00d2eed798abbb75 upstream.
This will clear the USB_PORT_FEAT_C_CONNECTION bit in case of a hub port reset
only if a device is was attached to the hub port before resetting the hub port.
Using a Lenovo T480s attached to the ultra dock it was not possible to detect
some usb-c devices at the dock usb-c ports because the hub_port_reset code
will clear the USB_PORT_FEAT_C_CONNECTION bit after the actual hub port reset.
Using this device combo the USB_PORT_FEAT_C_CONNECTION bit was set between the
actual hub port reset and the clear of the USB_PORT_FEAT_C_CONNECTION bit.
This ends up with clearing the USB_PORT_FEAT_C_CONNECTION bit after the
new device was attached such that it was not detected.
This patch will not clear the USB_PORT_FEAT_C_CONNECTION bit if there is
currently no device attached to the port before the hub port reset.
This will avoid clearing the connection bit for new attached devices.
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a77112577667cbda7c6292c52d909636aef31fd9 upstream.
Following on from this patch: https://lkml.org/lkml/2017/11/3/516,
Corsair K70 LUX RGB keyboards also require the DELAY_INIT quirk to
start correctly at boot.
Dmesg output:
usb 1-6: string descriptor 0 read error: -110
usb 1-6: New USB device found, idVendor=1b1c, idProduct=1b33
usb 1-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-6: can't set config #1, error -110
Signed-off-by: Emmanuel Pescosta <emmanuelpescosta099@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit deefd24228a172d1b27d4a9adbfd2cdacd60ae64 upstream.
Raydium USB touchscreen fails to set config if LPM is enabled:
[ 2.030658] usb 1-8: New USB device found, idVendor=2386, idProduct=3119
[ 2.030659] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.030660] usb 1-8: Product: Raydium Touch System
[ 2.030661] usb 1-8: Manufacturer: Raydium Corporation
[ 7.132209] usb 1-8: can't set config #1, error -110
Same behavior can be observed on 2386:3114.
Raydium claims the touchscreen supports LPM under Windows, so I used
Microsoft USB Test Tools (MUTT) [1] to check its LPM status. MUTT shows
that the LPM doesn't work under Windows, either. So let's just disable LPM
for Raydium touchscreens.
[1] https://docs.microsoft.com/en-us/windows-hardware/drivers/usbcon/usb-test-tools
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 665c365a77fbfeabe52694aedf3446d5f2f1ce42 upstream.
Commit 7a68d9fb8510 ("USB: usbdevfs: sanitize flags more") checks the
transfer flags for URBs submitted from userspace via usbfs. However,
the check for whether the USBDEVFS_URB_SHORT_NOT_OK flag should be
allowed for a control transfer was added in the wrong place, before
the code has properly determined the direction of the control
transfer. (Control transfers are special because for them, the
direction is set by the bRequestType byte of the Setup packet rather
than direction bit of the endpoint address.)
This patch moves code which sets up the allow_short flag for control
transfers down after is_in has been set to the correct value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+24a30223a4b609bb802e@syzkaller.appspotmail.com
Fixes: 7a68d9fb8510 ("USB: usbdevfs: sanitize flags more")
CC: Oliver Neukum <oneukum@suse.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c183813fcee44a249339b7c46e1ad271ca1870aa upstream.
usb_driver_claim_interface() disables and re-enables Link Power
Management, but it shouldn't do either one, for the reasons listed
below. This patch removes the two LPM-related function calls from the
routine.
The reason for disabling LPM in the analogous function
usb_probe_interface() is so that drivers won't have to deal with
unwanted LPM transitions in their probe routine. But
usb_driver_claim_interface() doesn't call the driver's probe routine
(or any other callbacks), so that reason doesn't apply here.
Furthermore, no driver other than usbfs will ever call
usb_driver_claim_interface() unless it is already bound to another
interface in the same device, which means disabling LPM here would be
redundant. usbfs doesn't interact with LPM at all.
Lastly, the error return from usb_unlocked_disable_lpm() isn't handled
properly; the code doesn't clean up its earlier actions before
returning.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 8306095fd2 ("USB: Disable USB 3.0 LPM in critical sections.")
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81e0403b26d94360abd1f6a57311337973bc82cd upstream.
If we filter flags before they reach the core we need to generate our
own warnings.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 0cb54a3e47 ("USB: debugging code shouldn't alter control flow")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a68d9fb851012829c29e770621905529bd9490b upstream.
Requesting a ZERO_PACKET or not is sensible only for output.
In the input direction the device decides.
Likewise accepting short packets makes sense only for input.
This allows operation with panic_on_warn without opening up
a local DOS.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: syzbot+843efa30c8821bd69f53@syzkaller.appspotmail.com
Fixes: 0cb54a3e47 ("USB: debugging code shouldn't alter control flow")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9a4cb204e9eb7fa7dfbe3f7d3a674fa530aa193 upstream.
usb_find_alt_setting() takes a pointer to a struct usb_host_config as
an argument; it searches for an interface with specified interface and
alternate setting numbers in that config. However, it crashes if the
usb_host_config pointer argument is NULL.
Since this is a general-purpose routine, available for use in many
places, we want to to be more robust. This patch makes it return NULL
whenever the config argument is NULL.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+19c3aaef85a89d451eac@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd729f9d67aa9a303d8925bb8c4f06af25f407d1 upstream.
The syzbot fuzzing project found a use-after-free bug in the USB
core. The bug was caused by usbfs not unbinding from an interface
when the USB device file was closed, which led another process to
attempt the unbind later on, after the private data structure had been
deallocated.
The reason usbfs did not unbind the interface at the appropriate time
was because it thought the interface had never been claimed in the
first place. This was caused by the fact that
usb_driver_claim_interface() does not clean up properly when
device_bind_driver() returns an error. Although the error code gets
passed back to the caller, the iface->dev.driver pointer remains set
and iface->condition remains equal to USB_INTERFACE_BOUND.
This patch adds proper error handling to usb_driver_claim_interface().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+f84aa7209ccec829536f@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b83a1c301ad6d24988a128c69b42cbaaf537d82 upstream.
WORLDE Controller KS49 or Prodipe MIDI 49C USB controller
cause a -EPROTO error, a communication restart and loop again.
This issue has already been fixed for KS25.
https://lore.kernel.org/patchwork/patch/753077/
I just add device 201 for KS49 in quirks.c to get it works.
Signed-off-by: Laurent Roux <xpros64@hotmail.fr>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9a5b4f58b280c1d26255376713c132f93837621 upstream.
The steps taken by usb core to set a new interface is very different from
what is done on the xHC host side.
xHC hardware will do everything in one go. One command is used to set up
new endpoints, free old endpoints, check bandwidth, and run the new
endpoints.
All this is done by xHC when usb core asks the hcd to check for
available bandwidth. At this point usb core has not yet flushed the old
endpoints, which will cause use-after-free issues in xhci driver as
queued URBs are cancelled on a re-allocated endpoint.
To resolve this add a call to usb_disable_interface() which will flush
the endpoints before calling usb_hcd_alloc_bandwidth()
Additional checks in xhci driver will also be implemented to gracefully
handle stale URB cancel on freed and re-allocated endpoints
Cc: <stable@vger.kernel.org>
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f45681f9becaa65111ed0a691ccf080a0cd5feb8 upstream.
This device does not correctly handle the LPM operations.
Also, the device cannot handle ATA pass-through commands
and locks up when attempted while running in super speed.
This patch adds the equivalent quirk logic as found in uas.
Signed-off-by: Tim Anderson <tsa@biglakesoftware.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3dc41c5d22b2ca14a0802a65d8cdc33a3882d4e upstream.
usb_hc_died() should only be called once, and with the primary HCD
as parameter. It will mark both primary and secondary hcd's dead.
Remove the extra call to usb_cd_died with the shared hcd as parameter.
Fixes: ff9d78b36f ("USB: Set usb_hcd->state and flags for shared roothubs")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5d111f5190848d6fb1c414dc57797efea3526a2f ]
wait_for_connected() wait till a port change status to
USB_PORT_STAT_CONNECTION, but this is not possible if
the port is unpowered. The loop will only exit at timeout.
Such case take place if an over-current incident happen
while system is in S3. Then during resume wait_for_connected()
will wait 2s, which may be noticeable by the user.
Signed-off-by: Dominik Bozek <dominikx.bozek@intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 249a32b7eeb3edb6897dd38f89651a62163ac4ed upstream.
Based on USB2.0 Spec Section 11.12.5,
"If a hub has per-port power switching and per-port current limiting,
an over-current on one port may still cause the power on another port
to fall below specific minimums. In this case, the affected port is
placed in the Power-Off state and C_PORT_OVER_CURRENT is set for the
port, but PORT_OVER_CURRENT is not set."
so let's check C_PORT_OVER_CURRENT too for over current condition.
Fixes: 08d1dec6f4 ("usb:hub set hub->change_bits when over-current happens")
Cc: <stable@vger.kernel.org>
Tested-by: Alessandro Antenucci <antenucci@korg.it>
Signed-off-by: Bin Liu <b-liu@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bba57eddadda936c94b5dccf73787cb9e159d0a5 upstream.
Corsair Strafe appears to suffer from the same issues
as the Corsair Strafe RGB.
Apply the same quirks (control message delay and init delay)
that the RGB version has to 1b1c:1b15.
With these quirks in place the keyboard works correctly upon
booting the system, and no longer requires reattaching the device.
Signed-off-by: Nico Sneck <snecknico@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e01827ed93947895680fbdad68c072a0f4e2450 upstream.
Some low-speed and full-speed devices (for example, bluetooth)
do not have time to initialize. For them, ETIMEDOUT is a valid error.
We need to give them another try. Otherwise, they will
never be initialized correctly and in dmesg will be messages
"Bluetooth: hci0 command 0x1002 tx timeout" or similars.
Fixes: 264904ccc33c ("usb: retry reset if a device times out")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Maxim Moseychuk <franchesko.salias.hudro.pedros@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb5ee84ea72c5f1b6cabdd1c9d6e8648995ca7c6 upstream.
Some non-compliant high-speed USB devices have bulk endpoints with a
1024-byte maxpacket size. Although such endpoints don't work with
xHCI host controllers, they do work with EHCI controllers. We used to
accept these invalid sizes (with a warning), but we no longer do
because of an unintentional change introduced by commit aed9d65ac327
("USB: validate wMaxPacketValue entries in endpoint descriptors").
This patch restores the old behavior, so that people with these
peculiar devices can use them without patching their kernels by hand.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Elvinas <elvinas@veikia.lt>
Fixes: aed9d65ac327 ("USB: validate wMaxPacketValue entries in endpoint descriptors")
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83a62c51ba7b3c0bf45150c4eac7aefc6c785e94 upstream.
On chromebooks we depend on wakeup count to identify the wakeup source.
But currently USB devices do not increment the wakeup count when they
trigger the remote wake. This patch addresses the same.
Resume condition is reported differently on USB 2.0 and USB 3.0 devices.
On USB 2.0 devices, a wake capable device, if wake enabled, drives
resume signal to indicate a remote wake (USB 2.0 spec section 7.1.7.7).
The upstream facing port then sets C_PORT_SUSPEND bit and reports a
port change event (USB 2.0 spec section 11.24.2.7.2.3). Thus if a port
has resumed before driving the resume signal from the host and
C_PORT_SUSPEND is set, then the device attached to the given port might
be the reason for the last system wakeup. Increment the wakeup count for
the same.
On USB 3.0 devices, a function may signal that it wants to exit from device
suspend by sending a Function Wake Device Notification to the host (USB3.0
spec section 8.5.6.4) Thus on receiving the Function Wake, increment the
wakeup count.
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3180dabe08e3653bf0a838553905d88f3773f29c upstream.
Add DELAY_INIT quirk to fix the following problem with HP
v222w 16GB Mini:
usb 1-3: unable to read config index 0 descriptor/start: -110
usb 1-3: can't read configurations, error -110
usb 1-3: can't set config #1, error -110
Signed-off-by: Kamil Lulko <kamilx.lulko@intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64627388b50158fd24d6ad88132525b95a5ef573 upstream.
USB3 hubs don't support global suspend.
USB3 specification 10.10, Enhanced SuperSpeed hubs only support selective
suspend and resume, they do not support global suspend/resume where the
hub downstream facing ports states are not affected.
When system enters hibernation it first enters freeze process where only
the root hub enters suspend, usb_port_suspend() is not called for other
devices, and suspend status flags are not set for them. Other devices are
expected to suspend globally. Some external USB3 hubs will suspend the
downstream facing port at global suspend. These devices won't be resumed
at thaw as the suspend status flag is not set.
A USB3 removable hard disk connected through a USB3 hub that won't resume
at thaw will fail to synchronize SCSI cache, return “cmd cmplt err -71”
error, and needs a 60 seconds timeout which causing system hang for 60s
before the USB host reset the port for the USB3 removable hard disk to
recover.
Fix this by always calling usb_port_suspend() during freeze for USB3
devices.
Signed-off-by: Zhengjun Xing <zhengjun.xing@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb88a0588717ba6c756cb5972d75766b273a6817 upstream.
Corsair Strafe RGB keyboard does not respond to usb control messages
sometimes and hence generates timeouts.
Commit de3af5bf259d ("usb: quirks: add delay init quirk for Corsair
Strafe RGB keyboard") tried to fix those timeouts by adding
USB_QUIRK_DELAY_INIT.
Unfortunately, even with this quirk timeouts of usb_control_msg()
can still be seen, but with a lower frequency (approx. 1 out of 15):
[ 29.103520] usb 1-8: string descriptor 0 read error: -110
[ 34.363097] usb 1-8: can't set config #1, error -110
Adding further delays to different locations where usb control
messages are issued just moves the timeouts to other locations,
e.g.:
[ 35.400533] usbhid 1-8:1.0: can't add hid device: -110
[ 35.401014] usbhid: probe of 1-8:1.0 failed with error -110
The only way to reliably avoid those issues is having a pause after
each usb control message. In approx. 200 boot cycles no more timeouts
were seen.
Addionaly, keep USB_QUIRK_DELAY_INIT as it turned out to be necessary
to have the delay in hub_port_connect() after hub_port_init().
The overall boot time seems not to be influenced by these additional
delays, even on fast machines and lightweight distributions.
Fixes: de3af5bf259d ("usb: quirks: add delay init quirk for Corsair Strafe RGB keyboard")
Cc: stable@vger.kernel.org
Signed-off-by: Danilo Krummrich <danilokrummrich@dk-develop.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a1646d922577b5b48c0d222e03831141664bb59 upstream.
Following on from this patch: https://lkml.org/lkml/2017/11/3/516,
Corsair K70 RGB keyboards also require the DELAY_INIT quirk to
start correctly at boot.
Device ids found here:
usb 3-3: New USB device found, idVendor=1b1c, idProduct=1b13
usb 3-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 3-3: Product: Corsair K70 RGB Gaming Keyboard
Signed-off-by: Jack Stocker <jackstocker.93@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07b9f12864d16c3a861aef4817eb1efccbc5d0e6 upstream.
USB 3.1 devices are not detected as 3.1 capable since 4.15-rc3 due to a
off by one in commit 81cf4a45360f ("USB: core: Add type-specific length
check of BOS descriptors")
It uses USB_DT_USB_SSP_CAP_SIZE() to get SSP capability size which takes
the zero based SSAC as argument, not the actual count of sublink speed
attributes.
USB3 spec 9.6.2.5 says "The number of Sublink Speed Attributes = SSAC + 1."
The type-specific length check patch was added to stable and needs to be
fixed there as well
Fixes: 81cf4a45360f ("USB: core: Add type-specific length check of BOS descriptors")
CC: Masakazu Mokuno <masakazu.mokuno@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b9096d9f15c142574ebebe8fbb137012bb9d99c2 upstream.
This modem needs this quirk to operate. It produces timeouts when
resumed without reset.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f038d256c723dd390d2fca942919573995f4cfd upstream.
Commit e0429362ab
("usb: Add device quirk for Logitech HD Pro Webcams C920 and C930e")
introduced quirk to workaround an issue with some Logitech webcams.
There is one more model that has the same issue - C925e, so applying
the same quirk as well.
See aforementioned commit message for detailed explanation of the problem.
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 48a4ff1c7bb5a32d2e396b03132d20d552c0eca7 upstream.
A malicious USB device with crafted descriptors can cause the kernel
to access unallocated memory by setting the bNumInterfaces value too
high in a configuration descriptor. Although the value is adjusted
during parsing, this adjustment is skipped in one of the error return
paths.
This patch prevents the problem by setting bNumInterfaces to 0
initially. The existing code already sets it to the proper value
after parsing is complete.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 446f666da9f019ce2ffd03800995487e79a91462 upstream.
USBDEVFS_URB_ISO_ASAP must be accepted only for ISO endpoints.
Improve sanity checking.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57999d1107c1e60c2ca7088f2ac0f819e2f554b3 upstream.
There used to be an integer overflow check in proc_do_submiturb() but
we removed it. It turns out that it's still required. The
uurb->buffer_length variable is a signed integer and it's controlled by
the user. It can lead to an integer overflow when we do:
num_sgs = DIV_ROUND_UP(uurb->buffer_length, USB_SG_SIZE);
If we strip away the macro then that line looks like this:
num_sgs = (uurb->buffer_length + USB_SG_SIZE - 1) / USB_SG_SIZE;
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
It's the first addition which can overflow.
Fixes: 1129d270cbfb ("USB: Increase usbfs transfer limit")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1129d270cbfbb7e2b1ec3dede4a13930bdd10e41 upstream.
Promote a variable keeping track of USB transfer memory usage to a
wider data type and allow for higher bandwidth transfers from a large
number of USB devices connected to a single host.
Signed-off-by: Mateusz Berezecki <mateuszb@fastmail.fm>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81cf4a45360f70528f1f64ba018d61cb5767249a upstream.
As most of BOS descriptors are longer in length than their header
'struct usb_dev_cap_header', comparing solely with it is not sufficient
to avoid out-of-bounds access to BOS descriptors.
This patch adds descriptor type specific length check in
usb_get_bos_descriptor() to fix the issue.
Signed-off-by: Masakazu Mokuno <masakazu.mokuno@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
