migrate_vmas() should check "vma" not "vma->vm_next" for for-loop condition.
Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 5a6fe12595 brought hugetlbfs more
in line with the core VM by obeying VM_NORESERVE and not reserving
hugepages for both shared and private mappings when [SHM|MAP]_NORESERVE
are specified. However, it is still taking filesystem quota
unconditionally.
At fault time, if there are no reserves and attempt is made to allocate
the page and account for filesystem quota. If either fail, the fault
fails. The impact is that quota is getting accounted for twice. This
patch partially reverts 5a6fe12595. To
help prevent this mistake happening again, it improves the documentation
of hugetlb_reserve_pages()
Reported-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Catalin noticed that (38d47c1b70: futex: rely on get_user_pages() for
shared futexes) caused an mm_struct leak.
Some tracing with the function graph tracer quickly pointed out that
futex_wait() has exit paths with unbalanced reference counts.
This regression was discovered by kmemleak.
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Tested-by: "Pallipadi, Venkatesh" <venkatesh.pallipadi@intel.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Here we do two things:
First, revert "iwlwifi: save PCI state before suspend, restore after
resume". That misguided patch led to being unable to use iwlwifi
devices after resume.
Next, indicate to PCI driver that the saved PCI state is valid during suspend.
We restore PCI state and enable the device when network interface is created,
similarly PCI state is saved and the device is disabled when network interface
is removed. Thus, when .suspend is called the PCI state is saved and device
is disabled. This is the case even if an interface is never created as PCI
state is saved and device disabled during .probe.
PCI driver assumes PCI state is saved in .suspend. Saving the state at this
time will save state of disabled device and thus cause problems during
resume (resuming a disabled device). We thus indicate directly to PCI
driver that current PCI saved state is valid.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Alex Riesen <fork0@users.sf.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Three people (Petr Mensik <pihhan@cipis.net>
["si" should be U+0161 U+00ED], Stephen Ho <stephenhoinhk@gmail.com>
on zd1211-devs and Ismael Ojeda Perez <iojedaperez@gmail.com>
on linux-wireless) reported success in getting TP-Link WN322G/WN422G
working by treating MAXIM_NEW_RF(0x08) as UW2453_RF(0x09) for rf
chip hardware initialization.
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Tested-by: Petr Mensik <pihhan@cipis.net>
Tested-by: Stephen Ho <stephenhoinhk@gmail.com>
Tested-by: Ismael Ojeda Perez <iojedaperez@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Christoph Biedl <sourceforge.bnwi@manchmal.in-ulm.de> reported success
in the sourceforge zd1211 mailing list on this addition. This product ID
was supported by the vendor driver ZD1211LnxDrv 2.22.0.0 (and possibly
earlier) and it probably should have been added earlier.
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Tested-by: Christoph Biedl <sourceforge.bnwi@manchmal.in-ulm.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We try to find the correct outgoing interface for injected frames
based on the TA, but since this is a hack for hostapd 11w, restrict
the heuristic to AP mode interfaces. At some point we'll add the
ability to give an interface index in radiotap or so and just
remove this heuristic again.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.28.x]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Under memory pressure, we may not be able to allocate a new skb for
new packets. If the allocation fails, ath5k_tasklet_rx will exit but
will leave a buffer in the list with a NULL skb, eventually triggering
a BUG_ON.
Extract the skb allocation from ath5k_rxbuf_setup() and change the
tasklet to allocate the next skb before accepting a packet.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
timers: fix TIMER_ABSTIME for process wide cpu timers
timers: split process wide cpu clocks/timers, fix
x86: clean up hpet timer reinit
timers: split process wide cpu clocks/timers, remove spurious warning
timers: split process wide cpu clocks/timers
signal: re-add dead task accumulation stats.
x86: fix hpet timer reinit for x86_64
sched: fix nohz load balancer on cpu offline
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ptrace, x86: fix the usage of ptrace_fork()
i8327: fix outb() parameter order
x86: fix math_emu register frame access
x86: math_emu info cleanup
x86: include correct %gs in a.out core dump
x86, vmi: put a missing paravirt_release_pmd in pgd_dtor
x86: find nr_irqs_gsi with mp_ioapic_routing
x86: add clflush before monitor for Intel 7400 series
x86: disable intel_iommu support by default
x86: don't apply __supported_pte_mask to non-present ptes
x86: fix grammar in user-visible BIOS warning
x86/Kconfig.cpu: make Kconfig help readable in the console
x86, 64-bit: print DMI info in the oops trace
Ptrace_detach() races with __ptrace_unlink() if the traced task is
reaped while detaching. This might cause a double-free of the BTS
buffer.
Change the ptrace_detach() path to only do the memory accounting in
ptrace_bts_detach() and leave the buffer free to ptrace_bts_untrace()
which will be called from __ptrace_unlink().
The fix follows a proposal from Oleg Nesterov.
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Intel reported a 10% regression (mysql+sysbench) on a 16-way machine
with these patches:
1596e29: sched: symmetric sync vs avg_overlap
d942fb6: sched: fix sync wakeups
Revert them.
Reported-by: "Zhang, Yanmin" <yanmin_zhang@linux.intel.com>
Bisected-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The POSIX timer interface allows for absolute time expiry values through the
TIMER_ABSTIME flag, therefore we have to synchronize the timer to the clock
every time we start it.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
To decrease the chance of a missed enable, always enable the timer when we
sample it, we'll always disable it when we find that there are no active timers
in the jiffy tick.
This fixes a flood of warnings reported by Mike Galbraith.
Reported-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In dasd_device_set_timer and dasd_block_set_timer we interpret the
return value of mod_timer in a wrong way. If the timer expires in
the small window between our check of timer_pending and the call to
mod_timer, then the timer will be set, mod_timer returns zero and
we will call add_timer for a timer that is already pending.
As del_timer and mod_timer do all the necessary checking themselves,
we can simplify our code and remove the race a the same time.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The vdso_per_cpu_data entry in the lowcore structure uses __u32
instead of __u64. If the data page is above 4GB the pointer is
truncated and the kernel crashes.
Reported-by: Mijo Safradin <mijo@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
I noticed by pure accident we have ptrace_fork() and friends. This was
added by "x86, bts: add fork and exit handling", commit
bf53de907d.
I can't test this, ds_request_bts() returns -EOPNOTSUPP, but I strongly
believe this needs the fix. I think something like this program
int main(void)
{
int pid = fork();
if (!pid) {
ptrace(PTRACE_TRACEME, 0, NULL, NULL);
kill(getpid(), SIGSTOP);
fork();
} else {
struct ptrace_bts_config bts = {
.flags = PTRACE_BTS_O_ALLOC,
.size = 4 * 4096,
};
wait(NULL);
ptrace(PTRACE_SETOPTIONS, pid, NULL, PTRACE_O_TRACEFORK);
ptrace(PTRACE_BTS_CONFIG, pid, &bts, sizeof(bts));
ptrace(PTRACE_CONT, pid, NULL, NULL);
sleep(1);
}
return 0;
}
should crash the kernel.
If the task is traced by its natural parent ptrace_reparented() returns 0
but we should clear ->btsxxx anyway.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The constraint used for retrieving and restoring the parent function
pointer is incorrect. The parent variable is a pointer, and the
address of the pointer is modified by the asm statement and not
the pointer itself. It is incorrect to pass it in as an output
constraint since the asm will never update the pointer.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We found that enabling/disabling HDMI audio pin out at stream start/stop
time will kill the leading 500ms or so sound samples. Avoid this by enabling
pin out once and for ever at module loading time.
The leading ~500ms audio samples will still be lost when switching from
X-channel playback to Y-channel playback where X != Y. However there's no
much we can do about it: the audio infoframe has to change and it looks like
either G45 or YAMAHA requires some time to switch the configuration.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The YAMAHA AV-X1800 requires audio infoframe to include speaker-channel
mapping to play >2 channel HDMI audio. In theory that mapping should be
derived from its speaker configurations contained in its ELD. However we
currently cannot get ELD in console before the KMS functionalities are ready.
This is a more or less general issue at least in the near future. As a
workaround, we propose to allow playback of mult-channel audio when ELD
is not available.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added a device tree that should be identical to mpc8572ds.dtb except
the physical addresses for all IO are above the 4G boundary.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The following commit:
commit 64b3d0e812
Author: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Date: Thu Dec 18 19:13:51 2008 +0000
powerpc/mm: Rework usage of _PAGE_COHERENT/NO_CACHE/GUARDED
broke setting of the _PAGE_COHERENT bit in the PPC HW PTE. Since we now
actually set _PAGE_COHERENT in the Linux PTE we shouldn't be clearing it
out before we propogate it to the PPC HW PTE.
Reported-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch reworks the way we do I and D cache coherency on PowerPC.
The "old" way was split in 3 different parts depending on the processor type:
- Hash with per-page exec support (64-bit and >= POWER4 only) does it
at hashing time, by preventing exec on unclean pages and cleaning pages
on exec faults.
- Everything without per-page exec support (32-bit hash, 8xx, and
64-bit < POWER4) does it for all page going to user space in update_mmu_cache().
- Embedded with per-page exec support does it from do_page_fault() on
exec faults, in a way similar to what the hash code does.
That leads to confusion, and bugs. For example, the method using update_mmu_cache()
is racy on SMP where another processor can see the new PTE and hash it in before
we have cleaned the cache, and then blow trying to execute. This is hard to hit but
I think it has bitten us in the past.
Also, it's inefficient for embedded where we always end up having to do at least
one more page fault.
This reworks the whole thing by moving the cache sync into two main call sites,
though we keep different behaviours depending on the HW capability. The call
sites are set_pte_at() which is now made out of line, and ptep_set_access_flags()
which joins the former in pgtable.c
The base idea for Embedded with per-page exec support, is that we now do the
flush at set_pte_at() time when coming from an exec fault, which allows us
to avoid the double fault problem completely (we can even improve the situation
more by implementing TLB preload in update_mmu_cache() but that's for later).
If for some reason we didn't do it there and we try to execute, we'll hit
the page fault, which will do a minor fault, which will hit ptep_set_access_flags()
to do things like update _PAGE_ACCESSED or _PAGE_DIRTY if needed, we just make
this guys also perform the I/D cache sync for exec faults now. This second path
is the catch all for things that weren't cleaned at set_pte_at() time.
For cpus without per-pag exec support, we always do the sync at set_pte_at(),
thus guaranteeing that when the PTE is visible to other processors, the cache
is clean.
For the 64-bit hash with per-page exec support case, we keep the old mechanism
for now. I'll look into changing it later, once I've reworked a bit how we
use _PAGE_EXEC.
This is also a first step for adding _PAGE_EXEC support for embedded platforms
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CONFIG_CC_OPTIMIZE_FOR_SIZE is selected, because otherwise the kernel
wouldn't boot. The AmigaOne's U-boot firmware seems to have a problem
loading uImages bigger than 1.8 MB.
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds the bootwrapper for the cuImage target and a compatible property
check for "pnpPNP,501" to the generic serial console support code.
The default link address for the cuImage target is set to 0x800000. This
allows to boot the kernel with AmigaOS4's second level bootloader, which
always loads a uImage at 0x500000.
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This device tree does not provide the correct CPU name, as various CPU
models and revisions are used in AmigaOnes. Also the PCI root node does
not contain a interrupt mapping property, as all boards have different
interrupt routing. However the kernel can do a 1:1 mapping of all PCI
interrupts, as only i8259 legacy interrupts are used.
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This commit adds the setup code for booting Linux on AmigaOne G3SE (G3
only), AmigaOne XE and uA1 (G3/G4) desktop computers. These boards were
sold by Eyetech and are based on MAI Logic's Teron boards and its
Articia S northbridge.
The AmigaOne uses U-boot as firmware, which doesn't support a flattened
device tree yet. The northbridge has some design flaws, which makes it
necessary to use non cacheable memory for DMA operations
(CONFIG_NOT_COHERENT_CACHE) and to avoid setting the coherence (M) flag
for memory pages.
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The EEH code disables and enables interrupts during the
device recovery process. This is unnecessary for MSI
and MSI-X interrupts because they are effectively disabled
by the DMA Stopped state when an EEH error occurs. The
current code is also incorrect for MSI-X interrupts. It
doesn't take into account that MSI-X interrupts are tracked
in a different way than LSI/MSI interrupts. This patch
ensures only LSI interrupts are disabled/enabled.
Signed-off-by: Mike Mason <mmlnx@us.ibm.com>
Acked-by: Linas Vepstas <linasvepstas@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
After the last changes, the mv643xx_eth driver now detects
a spurious interface on port 0. Since only port 1 is actually
connected to a PHY, remove its description.
Signed-off-by: Gabriel Paubert <paubert@iram.es>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As suggested, this is used for signed rather than unsigned
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
move the definition of hose_list next to its hotplug spinlock.
create pcibios_io_size to encapsulate ifdef in existing pci-common
function pcibios_vaddr_is_ioport
move pci_address_to_pio to pci-common, using new pcibios_io_size, and
protect this GPL exported function against concurrent hotplug removal
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we can't allocate the requested number of MSIs, we can still tell the
generic code how many we were able to allocate. That can then be passed
onto the driver, allowing it to request that many in future, and
probably succeeed.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We also need to check that the device isn't using MSI-X in the irq fixup
routine, otherwise we might leave MSI-Xs configured at boot.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Firmware encodes the number of MSI-X requested by a device in a
different property than for MSI. Pull the property name out as a
parameter and share the logic for both cases.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to increment i in the loop that queries what interrupts firmware
gave us, otherwise we'll incorrectly use the first value over and over.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The lmb_dump_all() output didn't include the RMO size, which is
interesting on powerpc. The output was also a bit spacey and not well
aligned, and didn't show you the end addresses.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The lmb debugging can be turned on at boottime with lmb=debug on the
command line. However on powerpc that doesn't work, because we don't
necessarily call lmb_dump_all().
So always call lmb_dump_all() after lmb_analyze(), no output is
generated unless lmb=debug is found on the command line.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
