The tid_data is not related to the transport layer, so move
the logic that depends on it to the upper layer.
This patch deals with tx AGG alloc.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The tid_data is not related to the transport layer, so move
the logic that depends on it to the upper layer.
This patch deals with tx AGG stop.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
In the same spirit as the previous patch. Eventually this will
allow us to remove the tid_data knowledge from the transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
In the very first implementation of HT, the driver was responsible
for the queueing: stopping and waking the queues while the HW queues
where being drained. In this implementation, we had to deal with the
case where we were draining the AGG queue because we wanted to tear
down the BA agreement.
In the normal flow (when we don't drain any HW queue), when packets
are reclaimed, we wake the SW queue in case the SW queue was stopped
which can happen when the HW queues are too full.
While draining a HW queue, we must make sure that we don't wake the
SW queue, since the whole point of the draining is to empty totally
the HW queue and not only get below a certain threshold.
This is why there is condition in the reclaim function:
if (NOT EMPTYING DELBA)
wake the SW queue is applicable
Since then, a lot has changed and mac80211 is now able to buffer
packets that are being sent to a packet list that will be spliced
after the driver has reported it has drained its HW queues.
Hence, there is no need for the for aforementioned if, and we can
safely wake up the queue even if we are draining HW queues.
Removing this if, also allows us to remove the wake_queue in
check_empty that was there in order to deal with a corner case
created by the if.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Since packets sent to an RA / TID in AGG are sent from a
separate HW Tx queue, we may get into a race:
the regular queue isn't empty while we already begin to
send packets from the AGG queue. This would result in sending
packets out of order.
In order to cope with this, mac80211 waits until the driver
reports that the legacy queue is drained before it can send
packets to the AGG queue. During that time, mac80211 buffers
packets for the driver. These packets will be sent in order
after the driver reports it is ready.
The way this was implemented in the driver is as follows:
We held a counter that monitors the number of packets for
an RA / TID in the HW queues. When this counter reached 0,
we knew that the HW queues were drained and we reported to
mac80211 that were ready to proceed.
This patch changes the implementation described above. We
now remember what is the wifi sequence number of the first
packet that will be sent in the AGG queue (lets' call it
ssn). When we reclaim the packet before ssn, we know that
the queue is drained, and we are ready to proceed.
This will allow us to move this logic in the upper layer and
eventually remove the tid_data from the shared area.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
ba_resp->seq_ctl is __le16, need to translate to cpu endianity.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Replace the engineering names with the marketing names for the
new devices.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Move the configuration pointer from the upper level iwl_priv to the
lower level iwl_shared structure, with associated code fixes.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
My previous patch
34a5b4b6af iwlwifi: do not re-configure
HT40 after associated
Fix the case of HT40 after association on specified AP, but it break the
association for some APs and cause not able to establish connection.
We need to address HT40 before and after addociation.
CC: stable@vger.kernel.org #3.0+
Reported-by: Andrej Gelenberg <andrej.gelenberg@udo.edu>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: Andrej Gelenberg <andrej.gelenberg@udo.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ted reported that he couldn't connect to some APs
and bisected it to the tx_sync implementation.
Disable it for the BSS context to fix this issue.
Reported-by: Ted Ts'o <tytso@mit.edu>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check the IEEE80211_TX_CTL_ASSIGN_SEQ flag from mac80211, then decide how to
set the TX_CMD_FLG_SEQ_CTL_MSK bit. Setting the wrong bit in BAR frame whill
make the firmware to increment the sequence number which is incorrect and
cause unknown behavior.
CC: stable@vger.kernel.org #3.0+
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We track the load only on 8 TIDs, previously this
was TID_MAX_LOAD_COUNT. Since IWL_MAX_TID_COUNT
is now 8 as well, use that to make the code more
easily understandable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Now that I corrected IWL_MAX_TID_COUNT to be 8
instead of 9, we can use it in WoWLAN suspend.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The driver everywhere uses max TID count as 9,
which is wrong, it should be 8.
I think the reason it uses 9 here is off-by-one
confusion by whoever wrote this. We do use the
value IWL_MAX_TID_COUNT for "not QoS/no TID"
but that is completely correct even if it is 8
and not 9 since 0-7 are only valid.
As a side effect, this fixes the following bug:
Open BA session requested for 00:23:cd:16:8a:7e tid 8
------------[ cut here ]------------
kernel BUG at drivers/net/wireless/iwlwifi/iwl-trans-pcie-int.h:350!
...
when you do
echo "tx start 8" > /sys/kernel/debug/ieee80211/*/*/*/*/agg_status
Cc: stable@vger.kernel.org
Reported-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Move the calib_results list from the upper layer iwl_priv structure
to the lower layer iwl_trans structure.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Move the low level ucode device_pointers structure to iwl_shared.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The eeprom image is a device level component, move from iwl_priv
to iwl_shared, with associated code changes.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
P2P still under development. it will not enabled by default, but user
always can enable it manually for testing.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Create new tm command to report devce ID information to userspace
- IWL_TM_CMD_APP2DEV_GET_DEVICE_ID
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
When uCode encounter problem, it pass a lot of debug data to help debugging
the issue. We only show partial data before, why not display all of those.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Because the testmode support should be the mandatory foundation
of test functionality, it is better to set kernel option
IWLWIFI_DEVICE_SVTOOL automatically instead of user configuration.
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Create new tm command to report uCode version to userspace
- IWL_TM_CMD_APP2DEV_GET_FW_VERSION
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Move the notification structures for ucode operations from the
iwl_priv structure to the iwl_shared structure, with associated
code changes.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the ucode_type variable from the iwl_priv to the iwl_shared
structure with associated code changes.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace the references to the iwl_priv structure with the iwl_trans
structure as the priv structure is never referenced other than to
access the trans structure. Rename from iwlagn to iwl.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl-agn-ucode is generic ucode operations, not limited just to iwlagn.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The file dealing with all the operations through testmode, rename it.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Create new tm command for WOWLAN uCode loading to support
further debugging function in userspace.
- IWL_TM_CMD_APP2DEV_LOAD_WOWLAN_FW
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using the actual shifted constants here allows
one to read and or them more easily.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is only used for TX debugging where there
already is more debugging and tracing is more
useful anyway, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This debug level is unused, remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This macro is unused right now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use generic chunk size of dumpit packet for
all necessary testmode commands instead of
add declaration individually.
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The size of sram may alter according to ucode type.
Retrieve the maximum sram size by current ucode
type for range checking to prevent wrong data access.
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Create new testmode commands and attributes to suppot
sram data reading. Because the amount of sram data
may exceed single skb packet size. Using the nl80211
dump it funtion to deliver sram data to userspace.
- IWL_TM_CMD_APP2DEV_READ_SRAM
- IWL_TM_CMD_APP2DEV_DUMP_SRAM
- IWL_TM_ATTR_SRAM_ADDR
- IWL_TM_ATTR_SRAM_SIZE
- IWL_TM_ATTR_SRAM_DUMP
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current default watchdog timer is enabled, but we are seeing issues on
legacy devices. So change the default setting of watchdog timer to per
device based. But user still can use the "wd_disable" module parameter
to overwrite the system setting
Cc: stable@vger.kernel.org #3.0+
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Group keys in IBSS or AP mode are not programmed
into the device since we give the key to it with
every TX packet. However, we do need mac80211 to
create the MMIC & PN in all cases. Move the code
around to set the key flags all the time. We set
them even when the key is removed again but that
is obviously harmless.
Cc: stable@vger.kernel.org
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the notification structures for ucode operations from the
iwl_priv structure to the iwl_shared structure, with associated
code changes.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Move the ucode_type variable from the iwl_priv to the iwl_shared
structure with associated code changes.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Replace the references to the iwl_priv structure with the iwl_trans
structure as the priv structure is never referenced other than to
access the trans structure. Rename from iwlagn to iwl.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
iwl-agn-ucode is generic ucode operations, not limited just to iwlagn.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
