This patch fixes a possible problem in the resume from
hibenration. It temporaneally saves the clk->rate on the
stack to avoid any possible change during the clk->set_parent(..)
call.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Improve the ap325 board code to allow the lcd panel
and backlight to be powered off.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains CONFIG_SUSPEND support to the SuperH
architecture. If enabled, SuperH Mobile processors will
register their suspend callbacks during boot.
To suspend, use "echo mem > /sys/power/state". To allow
wakeup, make sure "/sys/device/platform/../power/wakeup"
contains "enabled". Additional per-device driver patches
are most likely needed.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
dma-sh's get_dma_error_irq() is only used by SH4, as the SH3
doesn't have the DMA Error interrupt.
Disable it out for non-SH4 builds.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements preliminary suspend/resume support for the PMB.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This new compiler warning:
arch/powerpc/platforms/cell/interrupt.c: In function 'handle_iic_irq':
arch/powerpc/platforms/cell/interrupt.c:240: warning: unused variable 'cpu'
Triggers because the local variable 'cpu' became unused due to commit:
dee4102: sparseirq: use kstat_irqs_cpu instead
Remove the variable.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: ppc-dev <linuxppc-dev@ozlabs.org>
LKML-Reference: <20090316185256.4a160374.sfr@canb.auug.org.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It is trivial to merge the non-MMU and MMU versions of sigcontext.h.
Without a single file "make headers_install" is broken for m68k
(since each of the sub-varients of sigconext.h are not installed).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
It is trivial to merge the non-MMU and MMU versions of swab.h.
Without a single file "make headers_install" is broken for m68k
(since each of the sub-varients of swab.h are not installed).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
It is trivial to merge the non-MMU and MMU versions of param.h.
Without a single file "make headers_install" is broken for m68k
(since each of the sub-varients of param.h are not installed).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Ideally, the default should be set to 0 and let the EHCI driver turn
it on as needed. This makes USB usable in the mean time.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Here it is... HIGHMEM for the ARM architecture. :-)
If you don't have enough ram for highmem pages to be allocated and still
want to test this, then the cmdline option "vmalloc=" can be used with
a value large enough to force the highmem threshold down.
Successfully tested on a Marvell DB-78x00-BP Development Board with
2 GB of RAM.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
VIPT aliasing caches have issues of their own which are not yet handled.
Usage of discard_old_kernel_data() in copypage-v6.c is not highmem ready,
kmap/fixmap stuff doesn't take account of cache colouring, etc.
If/when those issues are handled then this could be reverted.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
On xsc3, L2 cache ops are possible only on virtual addresses. The code
is rearranged so to have a linear progression requiring the least amount
of pte setups in the highmem case. To protect the virtual mapping so
created, interrupts must be disabled currently up to a page worth of
address range.
The interrupt disabling is done in a way to minimize the overhead within
the inner loop. The alternative would consist in separate code for
the highmem and non highmem compilation which is less preferable.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The choice is between looping over the physical range and performing
single cache line operations, or to map highmem pages somewhere, as
cache range ops are possible only on virtual addresses.
Because L2 range ops are much faster, we go with the later by factoring
the physical-to-virtual address conversion and use a fixmap entry for it
in the HIGHMEM case.
Possible future optimizations to avoid the pte setup cost:
- do the pte setup for highmem pages only
- determine a threshold for doing a line-by-line processing on physical
addresses when the range is small
Signed-off-by: Nicolas Pitre <nico@marvell.com>
If a machine class has a custom __virt_to_bus() implementation then it
must provide a __arch_page_to_dma() implementation as well which is
_not_ based on page_address() to support highmem.
This patch fixes existing __arch_page_to_dma() and provide a default
implementation otherwise. The default implementation for highmem is
based on __pfn_to_bus() which is defined only when no custom
__virt_to_bus() is provided by the machine class.
That leaves only ebsa110 and footbridge which cannot support highmem
until they provide their own __arch_page_to_dma() implementation.
But highmem support on those legacy platforms with limited memory is
certainly not a priority.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This is a helper to be used by the DMA mapping API to handle cache
maintenance for memory identified by a page structure instead of a
virtual address. Those pages may or may not be highmem pages, and
when they're highmem pages, they may or may not be virtually mapped.
When they're not mapped then there is no L1 cache to worry about. But
even in that case the L2 cache must be processed since unmapped highmem
pages can still be L2 cached.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The kmap virtual area borrows a 2MB range at the top of the 16MB area
below PAGE_OFFSET currently reserved for kernel modules and/or the
XIP kernel. This 2MB corresponds to the range covered by 2 consecutive
second-level page tables, or a single pmd entry as seen by the Linux
page table abstraction. Because XIP kernels are unlikely to be seen
on systems needing highmem support, there shouldn't be any shortage of
VM space for modules (14 MB for modules is still way more than twice the
typical usage).
Because the virtual mapping of highmem pages can go away at any moment
after kunmap() is called on them, we need to bypass the delayed cache
flushing provided by flush_dcache_page() in that case.
The atomic kmap versions are based on fixmaps, and
__cpuc_flush_dcache_page() is used directly in that case.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This is the minimum fixmap interface expected to be implemented by
architectures supporting highmem.
We have a second level page table already allocated and covering
0xfff00000-0xffffffff because the exception vector page is located
at 0xffff0000, and various cache tricks already use some entries above
0xffff0000. Therefore the PTEs covering 0xfff00000-0xfffeffff are free
to be used.
However the XScale cache flushing code already uses virtual addresses
between 0xfffe0000 and 0xfffeffff.
So this reserves the 0xfff00000-0xfffdffff range for fixmap stuff.
The Documentation/arm/memory.txt information is updated accordingly,
including the information about the actual top of DMA memory mapping
region which didn't match the code.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
* master.kernel.org:/home/rmk/linux-2.6-arm: (23 commits)
[ARM] Fix virtual to physical translation macro corner cases
[ARM] update mach-types
[ARM] 5421/1: ftrace: fix crash due to tracing of __naked functions
MX1 fix include
[ARM] 5419/1: ep93xx: fix build warnings about struct i2c_board_info
[ARM] 5418/1: restore lr before leaving mcount
ARM: OMAP: board-omap3beagle: set i2c-3 to 100kHz
ARM: OMAP: Allow I2C bus driver to be compiled as a module
ARM: OMAP: sched_clock() corrected
ARM: OMAP: Fix compile error if pm.h is included
[ARM] orion5x: pass dram mbus data to xor driver
[ARM] S3C64XX: Fix s3c64xx_setrate_clksrc
[ARM] S3C64XX: sparse warnings in arch/arm/plat-s3c64xx/irq.c
[ARM] S3C64XX: sparse warnings in arch/arm/plat-s3c64xx/s3c6400-clock.c
[ARM] S3C64XX: Fix USB host clock mux list
[ARM] S3C64XX: Fix name of USB host clock.
[ARM] S3C64XX: Rename IRQ_UHOST to IRQ_USBH
[ARM] S3C64XX: Do gpiolib configuration earlier
[ARM] S3C64XX: Staticise s3c64xx_init_irq_eint()
[ARM] SMDK6410: Declare iodesc table static
...
Since now ipaq_model_ops used only for accessing h3600 EGPIOs,
drop it completely and use assign_h3600_egpio() directly.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Replace all occurences with assign_h3600_egpio.
Also simplify code a bit by replacing couple of if-else
statements with one-line equivalents.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove unused fields and associated funtions-accesors.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Right now iPaq h3600's default MTD partitions table is a mess. It has
two #ifdefs with #else, giving total 3 variants, depending on your
kernel config. Replace all this with simple two-partitions scheme
(bootloader + rootfs), that used by both shipped WindowsCE and
most of the linux distributions (Familiar, Angstrom)
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no actual code for iPAQ sleeves support in kernel that depends
on this config option.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: Mark Eins: Fix configuration.
MIPS: Fix TIF_32BIT undefined problem when seccomp is disabled
This patch adds basic support for Dave/DENX QongEVB-LITE i.MX31-based
board. It includes support for clocks initialization, UART1, NOR-flash,
FPGA-attached NAND flash and DNET ethernet controller (inside FPGA).
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds clkdev support for i.MX31. This is done in a
similar way done previously for i.MX27
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The UART3 had a copy-paste bug. instead of claiming rxd, txd, rts and
cts pins, cts and rts were claimed twice
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On MX31 we can't do much without mapping the AIPS1/2 register space.
Move these mappings from individual boards to plat-mxc/mm.c
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
