9f13ee6f83
(ARM: shmobile: r8a7790: add div4 clocks)
added r8a7790 DIV4 clock support.
But, it is missing
"0x0100: x 1/8" division ratio.
This patch fixes hidden bug.
It is based on R-Car H2 v0.7, R-Car M2 v0.9.
Reported-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commit 91ebb929b6 ("bnx2x: Add support for Multi-Function UNDI") [which was
later supposedly fixed by de682941ee ("bnx2x: Fix UNDI driver unload")]
introduced a bug in which in some [yet-to-be-determined] scenarios the
alternative flushing mechanism which was to guarantee the Rx buffers are
empty before resetting them during device probe will fail.
If this happens, when device will be loaded once more a fatal attention will
occur; Since this most likely happens in boot from SAN scenarios, the machine
will fail to load.
Notice this may occur not only in the 'Multi-Function' scenario but in the
regular scenario as well, i.e., this introduced a regression in the driver's
ability to perform boot from SAN.
The patch reverts the mechanism and applies the old scheme to multi-function
devices as well as to single-function devices.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shahed Shaikh says:
====================
qlcnic: Bug fixes
This series fixes some bugs related to endianess.
Please apply this series to net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware binary file is in little endian. On big-endian architecture, while
writing this binary FW file to adapters memory, writel() swaps the data resulting into
corruption of FW image. So, swap the data before writing into adapters memory.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware dump template header is read from adapter using
readl() which swaps the data. So, adjust structure
element on the boundary of 32bit dword.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Application expects flash data in little endian, but driver reads/writes
flash data using readl()/writel() APIs which swaps data on big endian machine.
So, swap the data after reading from and before writing to flash memory.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alan is the original author of the driver. This change was discussed
with the 802.15.4 subsystem maintainer, Alexander Aring.
Signed-off-by: Alan Ott <alan@signal11.us>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, macvlan code restricts multicast and unicast
filter setting only to passthru devices. As a result,
if a guest using macvtap wants to receive multicast
traffic, it has to set IFF_ALLMULTI or IFF_PROMISC.
This patch makes it possible to use the fdb interface
to add multicast addresses to the filter thus allowing
a guest to receive only targeted multicast traffic.
CC: John Fastabend <john.r.fastabend@intel.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Jason Wang <jasowang@redhat.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
af_packet can currently overwrite kernel memory by out of bound
accesses, because it assumed a [new] block can always hold one frame.
This is not generally the case, even if most existing tools do it right.
This patch clamps too long frames as API permits, and issue a one time
error on syslog.
[ 394.357639] tpacket_rcv: packet too big, clamped from 5042 to 3966. macoff=82
In this example, packet header tp_snaplen was set to 3966,
and tp_len was set to 5042 (skb->len)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: f6fb8f100b ("af-packet: TPACKET_V3 flexible buffer implementation.")
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LECS response contains the MTU that should be used. Correctly
synchronize with other layers when updating.
Signed-off-by: Chas Williams - CONTRACTOR <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Display fixes from Ville and Imre, all cc: stable.
* tag 'drm-intel-fixes-2014-08-21' of git://anongit.freedesktop.org/drm-intel:
drm/i915: don't try to retrain a DP link on an inactive CRTC
drm/i915: make sure VDD is turned off during system suspend
drm/i915: cancel hotplug and dig_port work during suspend and unload
drm/i915: fix HPD IRQ reenable work cancelation
drm/i915: take display port power domain in DP HPD handler
drm/i915: Don't try to enable cursor from setplane when crtc is disabled
drm/i915: Skip load detect when intel_crtc->new_enable==true
drm/i915: Fix locking for intel_enable_pipe_a()
more radeon fixes
* 'drm-fixes-3.17' of git://people.freedesktop.org/~agd5f/linux:
Revert "drm/radeon: Use write-combined CPU mappings of ring buffers with PCIe"
drm/radeon: fix active_cu mask on SI and CIK after re-init (v3)
drm/radeon: fix active cu count for SI and CIK
drm/radeon: re-enable selective GPUVM flushing
drm/radeon: Sync ME and PFP after CP semaphore waits v4
drm/radeon: fix display handling in radeon_gpu_reset
drm/radeon: fix pm handling in radeon_gpu_reset
drm/radeon: Only flush HDP cache for indirect buffers from userspace
drm/radeon: properly document reloc priority mask
Pull libata fixes from Tejun Heo:
"Nothing drastic but pushing out early due to build breakage in the new
tegra platform.
Additionally:
- M550 tagged trim blacklist pattern is widened so that it matches
the new 1TB model
- three controller specific fixes"
* 'for-3.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: widen Crucial M550 blacklist matching
pata_scc: propagate return value of scc_wait_after_reset
ata: ahci_tegra: Change include to fix compilation
pata_samsung_cf: change ret type to signed
ahci_xgene: Removing NCQ support from the APM X-Gene SoC AHCI SATA Host Controller driver.
Pull HID fixes from Jiri Kosina:
- fixes for a couple potential memory corruption problems (the HW would
have to be manufactured to be deliberately evil to trigger those)
found by Ben Hawkes
- fix for potential infinite loop when using sysfs interface of
logitech driver, from Simon Wood
- a couple more simple driver fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: fix a couple of off-by-ones
HID: logitech: perform bounds checking on device_id early enough
HID: logitech: fix bounds checking on LED report size
HID: logitech: Prevent possibility of infinite loop when using /sys interface
HID: rmi: print an error if F11 is not found instead of stopping the device
HID: hid-sensor-hub: use devm_ functions consistently
HID: huion: Use allocated buffer for DMA
HID: huion: Fail on parameter retrieval errors
A bunch of ASoC fixes with a few HD-audio fixes in this pull request.
All fairly small, boring and device-specific fixes, in addition to
MAINTAINERS update for better reviewing.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=x5gm
-----END PGP SIGNATURE-----
Merge tag 'sound-3.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A bunch of ASoC fixes with a few HD-audio fixes in this pull request.
All fairly small, boring and device-specific fixes, in addition to
MAINTAINERS update for better reviewing"
* tag 'sound-3.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/hdmi - apply Valleyview fix-ups to Cherryview display codec
ALSA: hda/hdmi - set depop_delay for haswell plus
ALSA: hda - restore the gpio led after resume
ALSA: hda/realtek - Avoid setting wrong COEF on ALC269 & co
ASoC: pxa-ssp: drop SNDRV_PCM_FMTBIT_S24_LE
ASoC: fsl-esai: Revert .xlate_tdm_slot_mask() support
ASoC: mcasp: Fix implicit BLCK divider setting
ASoC: arizona: Fix TDM slot length handling in arizona_hw_params
ASoC: pcm512x: Correct Digital Playback control names
ASoC: dapm: Fix uninitialized variable in snd_soc_dapm_get_enum_double()
ASoC: Intel: Restore Baytrail ADSP streams only when ADSP was in reset
ASoC: Intel: Wait Baytrail ADSP boot at resume_early stage
ASoC: Intel: Merge Baytrail ADSP suspend_noirq into suspend_late
MAINTAINERS: Add i.MX maintainers and paths to Freescale ASoC entry
ASoC: Intel: Update Baytrail ADSP firmware name
Pull i2c fixes from Wolfram Sang:
"Here is the fixup for the 'lowlight' of my last pull request. I2C is
not selected anymore by I2C_ACPI. Instead, the code in question now
depends on I2C=y.
Also, Mika has agreed to support me and be the maintainer for I2C-ACPI
related patches. Finally, a new-ID-patch came along last week"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: add maintainer for ACPI parts of I2C
i2c: i801: Add PCI ID for Intel Braswell
i2c: rework kernel config I2C_ACPI
This patch introduce need_do_checkpoint() to include numerous judgment condition
for readability.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Theoretically, our total inodes number is the same as total node number, but
there are three node ids are reserved in f2fs, they are 0, 1 (node nid), and 2
(meta nid), and they should never be used by user, so our total/free inode
number calculated in ->statfs is wrong.
This patch indroduces F2FS_RESERVED_NODE_NUM and then fixes this issue by
recalculating total/free inode number with the macro.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch checks inline_data one more time under the inode page lock whether
its inline_data is converted or not.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
I think we need to let the dirty node pages remain in the page cache instead
of rewriting them in their places.
So, after done with successful recovery, write_checkpoint will flush all of them
through the normal write path.
Through this, we can avoid potential error cases in terms of block allocation.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
The init_inode_metadata calls truncate_blocks when error is occurred.
The callers holds f2fs_lock_op, so we should not call it again in
truncate_blocks.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Any checkpoint should not be done during the core roll-forward procedure.
Especially, it includes error cases too.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
There are two rules when EIO is occurred.
1. don't write any checkpoint data to preserve the previous checkpoint
2. don't lose the cached dentry/node/meta pages
So, at first, this patch adds set_page_dirty in f2fs_write_end_io's failure.
Then, writing checkpoint/dentry/node blocks is not allowed.
Note that, for the data pages, we can't just throw away by redirtying them.
Otherwise, kworker can fall into infinite loop to flush them.
(Ref. xfstests/019)
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
The driver should not touch CS lines if SPI_NO_CS flag is set.
This patch fixes it as this functionality was broken accidentally
by
commit a88e34ea21 ("spi: davinci: add support to configure gpio cs through dt").
Fixes: a88e34ea21 ("spi: davinci: add support to configure gpio cs through dt")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
It needs to check s_dirty under cp_mutex, since s_dirty is reset under that
mutex.
And previous condition was not correct, since we can omit doing checkpoint
when checkpoint was done followed by all the node pages were written back.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch gives another chance to try mount process when we encounter an error.
This makes an effect on the roll-forward recovery failures as well.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
The generic_shutdown_super calls sync_filesystem, evict_inode, and then
f2fs_put_super. In f2fs_evict_inode, we remain some dirty inode information
so we should release them at f2fs_put_super.
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
There are a few very theoretical off-by-one bugs in report descriptor size
checking when performing a pre-parsing fixup. Fix those.
Cc: stable@vger.kernel.org
Reported-by: Ben Hawkes <hawkes@google.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
device_index is a char type and the size of paired_dj_deivces is 7
elements, therefore proper bounds checking has to be applied to
device_index before it is used.
We are currently performing the bounds checking in
logi_dj_recv_add_djhid_device(), which is too late, as malicious device
could send REPORT_TYPE_NOTIF_DEVICE_UNPAIRED early enough and trigger the
problem in one of the report forwarding functions called from
logi_dj_raw_event().
Fix this by performing the check at the earliest possible ocasion in
logi_dj_raw_event().
Cc: stable@vger.kernel.org
Reported-by: Ben Hawkes <hawkes@google.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The check on report size for REPORT_TYPE_LEDS in logi_dj_ll_raw_request()
is wrong; the current check doesn't make any sense -- the report allocated
by HID core in hid_hw_raw_request() can be much larger than
DJREPORT_SHORT_LENGTH, and currently logi_dj_ll_raw_request() doesn't
handle this properly at all.
Fix the check by actually trimming down the report size properly if it is
too large.
Cc: stable@vger.kernel.org
Reported-by: Ben Hawkes <hawkes@google.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We should only be flushing on close if the file was flagged as needing
it during truncate. I broke this with my ordered data vs transaction
commit deadlock fix.
Thanks to Miao Xie for catching this.
Signed-off-by: Chris Mason <clm@fb.com>
Reported-by: Miao Xie <miaox@cn.fujitsu.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
The crash is
------------[ cut here ]------------
kernel BUG at fs/btrfs/extent_io.c:2124!
[...]
Workqueue: btrfs-endio normal_work_helper [btrfs]
RIP: 0010:[<ffffffffa02d6055>] [<ffffffffa02d6055>] end_bio_extent_readpage+0xb45/0xcd0 [btrfs]
This is in fact a regression.
It is because we forgot to increase @offset properly in reading corrupted block,
so that the @offset remains, and this leads to checksum errors while reading
left blocks queued up in the same bio, and then ends up with hiting the above
BUG_ON.
Reported-by: Chris Murphy <lists@colorremedies.com>
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <clm@fb.com>
Coverity pointed this out; in the newly added
qgroup_subtree_accounting(), if btrfs_find_all_roots()
returns an error, we leak at least the parents pointer,
and possibly the roots pointer, depending on what failure
occurs.
If btrfs_find_all_roots() returns an error, we need to
free up all allocations before we return. "roots" is
initialized to NULL, so it should be safe to free
it unconditionally (ulist_free() handles that case).
Cc: Mark Fasheh <mfasheh@suse.de>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Mark Fasheh <mfasheh@suse.de>
Signed-off-by: Chris Mason <clm@fb.com>
When current btrfs finds that a new extent map is going to be insereted
but failed with -EEXIST, it will try again to insert the extent map
but with the length of sectorsize.
This is OK if we don't enable 'no-holes' feature since all extent space
is continuous, we will not go into the not found->insert routine.
But if we enable 'no-holes' feature, it will make things out of control.
e.g. in 4K sectorsize, we pass the following args to btrfs_get_extent():
btrfs_get_extent() args: start: 27874 len 4100
28672 27874 28672 27874+4100 32768
|-----------------------|
|---------hole--------------------|---------data----------|
1) not found and insert
Since no extent map containing the range, btrfs_get_extent() will go
into the not_found and insert routine, which will try to insert the
extent map (27874, 27847 + 4100).
2) first overlap
But it overlaps with (28672, 32768) extent, so -EEXIST will be returned
by add_extent_mapping().
3) retry but still overlap
After catching the -EEXIST, then btrfs_get_extent() will try insert it
again but with 4K length, which still overlaps, so -EEXIST will be
returned.
This makes the following patch fail to punch hole.
d77815461f btrfs: Avoid trucating page or punching hole in a already existed hole.
This patch will use the right length, which is the (exsisting->start -
em->start) to insert, making the above patch works in 'no-holes' mode.
Also, some small code style problems in above patch is fixed too.
Reported-by: Filipe David Manana <fdmanana@gmail.com>
Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Reviewed-by: Filipe David Manana <fdmanana@suse.com>
Tested-by: Filipe David Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
When cloning a file that consists of an inline extent, we were creating
an extent map that represents a non-existing trailing hole starting at a
file offset that isn't a multiple of the sector size. This happened because
when processing an inline extent we weren't aligning the extent's length to
the sector size, and therefore incorrectly treating the range
[inline_extent_length; sector_size[ as a hole.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
If an inode has a very large number of extent maps, we can spend
a lot of time freeing them, which triggers a soft lockup warning.
Therefore reschedule if we need to when freeing the extent maps
while evicting the inode.
I could trigger this all the time by running xfstests/generic/299 on
a file system with the no-holes feature enabled. That test creates
an inode with 11386677 extent maps.
$ mkfs.btrfs -f -O no-holes $TEST_DEV
$ MKFS_OPTIONS="-O no-holes" ./check generic/299
generic/299 382s ...
Message from syslogd@debian-vm3 at Aug 7 10:44:29 ...
kernel:[85304.208017] BUG: soft lockup - CPU#0 stuck for 22s! [umount:25330]
384s
Ran: generic/299
Passed all 1 tests
$ dmesg
(...)
[86304.300017] BUG: soft lockup - CPU#0 stuck for 23s! [umount:25330]
(...)
[86304.300036] Call Trace:
[86304.300036] [<ffffffff81698ba9>] __slab_free+0x54/0x295
[86304.300036] [<ffffffffa02ee9cc>] ? free_extent_map+0x5c/0xb0 [btrfs]
[86304.300036] [<ffffffff811a6cd2>] kmem_cache_free+0x282/0x2a0
[86304.300036] [<ffffffffa02ee9cc>] free_extent_map+0x5c/0xb0 [btrfs]
[86304.300036] [<ffffffffa02e3775>] btrfs_evict_inode+0xd5/0x660 [btrfs]
[86304.300036] [<ffffffff811e7c8d>] ? __inode_wait_for_writeback+0x6d/0xc0
[86304.300036] [<ffffffff816a389b>] ? _raw_spin_unlock+0x2b/0x40
[86304.300036] [<ffffffff811d8cbb>] evict+0xab/0x180
[86304.300036] [<ffffffff811d8dce>] dispose_list+0x3e/0x60
[86304.300036] [<ffffffff811d9b04>] evict_inodes+0xf4/0x110
[86304.300036] [<ffffffff811bd953>] generic_shutdown_super+0x53/0x110
[86304.300036] [<ffffffff811bdaa6>] kill_anon_super+0x16/0x30
[86304.300036] [<ffffffffa02a78ba>] btrfs_kill_super+0x1a/0xa0 [btrfs]
[86304.300036] [<ffffffff811bd3a9>] deactivate_locked_super+0x59/0x80
[86304.300036] [<ffffffff811be44e>] deactivate_super+0x4e/0x70
[86304.300036] [<ffffffff811dec14>] mntput_no_expire+0x174/0x1f0
[86304.300036] [<ffffffff811deab7>] ? mntput_no_expire+0x17/0x1f0
[86304.300036] [<ffffffff811e0517>] SyS_umount+0x97/0x100
(...)
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Tested-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
The file hole detection logic during a file fsync wasn't correct,
because it didn't look back (in a previous leaf) for the last file
extent item that can be in a leaf to the left of our leaf and that
has a generation lower than the current transaction id. This made it
assume that a hole exists when it really doesn't exist in the file.
Such false positive hole detection happens in the following scenario:
* We have a file that has many file extent items, covering 3 or more
btree leafs (the first leaf must contain non file extent items too).
* Two ranges of the file are modified, with their extent items being
located at 2 different leafs and those leafs aren't consecutive.
* When processing the second modified leaf, we weren't checking if
some file extent item exists that is located in some leaf that is
between our 2 modified leafs, and therefore assumed the range defined
between the last file extent item in the first leaf and the first file
extent item in the second leaf matched a hole.
Fortunately this didn't result in overriding the log with wrong data,
instead it made the last loop in copy_items() attempt to insert a
duplicated key (for a hole file extent item), which makes the file
fsync code return with -EEXIST to file.c:btrfs_sync_file() which in
turn ends up doing a full transaction commit, which is much more
expensive then writing only to the log tree and wait for it to be
durably persisted (as well as the file's modified extents/pages).
Therefore fix the hole detection logic, so that we don't pay the
cost of doing full transaction commits.
I could trigger this issue with the following test for xfstests (which
never fails, either without or with this patch). The last fsync call
results in a full transaction commit, due to the -EEXIST error mentioned
above. I could also observe this behaviour happening frequently when
running xfstests/generic/075 in a loop.
Test:
_cleanup()
{
_cleanup_flakey
rm -fr $tmp
}
# get standard environment, filters and checks
. ./common/rc
. ./common/filter
. ./common/dmflakey
# real QA test starts here
_supported_fs btrfs
_supported_os Linux
_require_scratch
_require_dm_flakey
_need_to_be_root
rm -f $seqres.full
# Create a file with many file extent items, each representing a 4Kb extent.
# These items span 3 btree leaves, of 16Kb each (default mkfs.btrfs leaf size
# as of btrfs-progs 3.12).
_scratch_mkfs -l 16384 >/dev/null 2>&1
_init_flakey
SAVE_MOUNT_OPTIONS="$MOUNT_OPTIONS"
MOUNT_OPTIONS="$MOUNT_OPTIONS -o commit=999"
_mount_flakey
# First fsync, inode has BTRFS_INODE_NEEDS_FULL_SYNC flag set.
$XFS_IO_PROG -f -c "pwrite -S 0x01 -b 4096 0 4096" -c "fsync" \
$SCRATCH_MNT/foo | _filter_xfs_io
# For any of the following fsync calls, inode doesn't have the flag
# BTRFS_INODE_NEEDS_FULL_SYNC set.
for ((i = 1; i <= 500; i++)); do
OFFSET=$((4096 * i))
LEN=4096
$XFS_IO_PROG -c "pwrite -S 0x01 $OFFSET $LEN" -c "fsync" \
$SCRATCH_MNT/foo | _filter_xfs_io
done
# Commit transaction and bump next transaction's id (to 7).
sync
# Truncate will set the BTRFS_INODE_NEEDS_FULL_SYNC flag in the btrfs's
# inode runtime flags.
$XFS_IO_PROG -c "truncate 2048000" $SCRATCH_MNT/foo
# Commit transaction and bump next transaction's id (to 8).
sync
# Touch 1 extent item from the first leaf and 1 from the last leaf. The leaf
# in the middle, containing only file extent items, isn't touched. So the
# next fsync, when calling btrfs_search_forward(), won't visit that middle
# leaf. First and 3rd leaf have now a generation with value 8, while the
# middle leaf remains with a generation with value 6.
$XFS_IO_PROG \
-c "pwrite -S 0xee -b 4096 0 4096" \
-c "pwrite -S 0xff -b 4096 2043904 4096" \
-c "fsync" \
$SCRATCH_MNT/foo | _filter_xfs_io
_load_flakey_table $FLAKEY_DROP_WRITES
md5sum $SCRATCH_MNT/foo | _filter_scratch
_unmount_flakey
_load_flakey_table $FLAKEY_ALLOW_WRITES
# During mount, we'll replay the log created by the fsync above, and the file's
# md5 digest should be the same we got before the unmount.
_mount_flakey
md5sum $SCRATCH_MNT/foo | _filter_scratch
_unmount_flakey
MOUNT_OPTIONS="$SAVE_MOUNT_OPTIONS"
status=0
exit
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
If we open a file with O_TMPFILE, don't do any further operation on
it (so that the inode item isn't updated) and then force a transaction
commit, we get a persisted inode item with a link count of 1, and not 0
as it should be.
Steps to reproduce it (requires a modern xfs_io with -T support):
$ mkfs.btrfs -f /dev/sdd
$ mount -o /dev/sdd /mnt
$ xfs_io -T /mnt &
$ sync
Then btrfs-debug-tree shows the inode item with a link count of 1:
$ btrfs-debug-tree /dev/sdd
(...)
fs tree key (FS_TREE ROOT_ITEM 0)
leaf 29556736 items 4 free space 15851 generation 6 owner 5
fs uuid f164d01b-1b92-481d-a4e4-435fb0f843d0
chunk uuid 0e3d0e56-bcca-4a1c-aa5f-cec2c6f4f7a6
item 0 key (256 INODE_ITEM 0) itemoff 16123 itemsize 160
inode generation 3 transid 6 size 0 block group 0 mode 40755 links 1
item 1 key (256 INODE_REF 256) itemoff 16111 itemsize 12
inode ref index 0 namelen 2 name: ..
item 2 key (257 INODE_ITEM 0) itemoff 15951 itemsize 160
inode generation 6 transid 6 size 0 block group 0 mode 100600 links 1
item 3 key (ORPHAN ORPHAN_ITEM 257) itemoff 15951 itemsize 0
orphan item
checksum tree key (CSUM_TREE ROOT_ITEM 0)
(...)
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
This is a better solution for the problem addressed in the following
commit:
Btrfs: update commit root on snapshot creation after orphan cleanup
(3821f34888)
The previous solution wasn't the best because of 2 reasons:
1) It added another full transaction commit, which is more expensive
than just swapping the commit root with the root;
2) If a reboot happened after the first transaction commit (the one
that creates the snapshot) and before the second transaction commit,
then we would end up with the same problem if a send using that
snapshot was requested before the first transaction commit after
the reboot.
This change addresses those 2 issues. The second issue is addressed by
switching the commit root in the dentry lookup VFS callback, which is
also called by the snapshot/subvol creation ioctl and performs orphan
cleanup if needed. Like the vfs, the ioctl locks the parent inode too,
preventing race issues between a dentry lookup and snapshot creation.
Cc: Alex Lyakas <alex.btrfs@zadarastorage.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Commit 49c6f736f34f901117c20960ebd7d5e60f12fcac(
btrfs: dev replace should replace the sysfs entry) added the missing sysfs entry
in the process of device replace, but didn't take missing devices into account,
so now we have
BUG: unable to handle kernel NULL pointer dereference at 0000000000000088
IP: [<ffffffffa0268551>] btrfs_kobj_rm_device+0x21/0x40 [btrfs]
...
To reproduce it,
1. mkfs.btrfs -f disk1 disk2
2. mkfs.ext4 disk1
3. mount disk2 /mnt -odegraded
4. btrfs replace start -B 1 disk3 /mnt
--------------------------
This fixes the problem.
Reported-by: Chris Murphy <lists@colorremedies.com>
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Tested-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
It appears that input sensing bit might be reset during
suspend/resume. Set input sensing again for all requested gpios
in resume
Tested-by: Jerome Blin <jerome.blin@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIOD flags are defined inside the #ifdef CONFIG_GPIOLIB
switch, making the gpiolib stubs fail if these flags are used
by a consumer. This is not correct: the stubs should compile
fine without GPIOLIB.
Reported-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The example in the binding document indicates that interrupt 32 is used
for the TLMM summary IRQ. Correct this to reduce the confusion.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
