Since version 7.4 the FW configures in the pci config space the max
number of interrupts available to the physical function, instead of
the exact number to use.
This causes a false warning in driver when comparing the number of
configured interrupts to the number about to be used.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the modes of Huawei E367 has this QMI/wwan interface:
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=07 Driver=(none)
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
Huawei use subclass and protocol to identify vendor specific
functions, so adding a new vendor rule for this combination.
The Pantech devices UML290 (106c:3718) and P4200 (106c:3721) use
the same subclass to identify the QMI/wwan function. Replace the
existing device specific UML290 entries with generic vendor matching,
adding support for the Pantech P4200.
The ZTE MF683 has 6 vendor specific interfaces, all using
ff/ff/ff for cls/sub/prot. Adding a match on interface #5 which
is a QMI/wwan interface.
Cc: Fangxiaozhi (Franko) <fangxiaozhi@huawei.com>
Cc: Thomas Schäfer <tschaefer@t-online.de>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Shawn J. Goff <shawn7400@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Revision 1.0 Janz CMOD-IO Carrier Board does not have support for
the reset registers. To support older hardware, the code is changed to
use the hardware reset register on the Janz VMOD-ICAN3 hardware itself.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
socfpga, picoxcell, and vexpress.
Multi-platform support is dependent on mach/gpio.h removal and
restructuring of DEBUG_LL and dtb build rules included in this branch.
This has been built for all defconfigs, and booted on highbank with
all 5 platforms enabled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQU4miAAoJEMhvYp4jgsXi1vMH/A4JJXe24cyo31rHJspZDSFg
nnCbnGKfDEOIHwLA8C3OeJuhswMlP/vWlGC512QXL8903XpZ2VJe63f2CLo1mN7Z
hg3JPWrp2VXZ/bqdMnUcw2CtlylrhyG9MUPapkcp+5Agjz2lwaJtRNL6LRRQX4Ei
cWjsJtaFpRj1QraFna0hpTQNO640je6s1rAIJl6eNOuX08l12ZAGDUA+IUUsa1cA
0OGeOAjH6gmkpMI89j1VPPKVRLHIdP4QcxmAZCHJ2LtvylyrlmYskctpAYibobvt
JPLnZgzMFAegnWtJhOYodhBJlfyypEeh2fsZVyDPowqRz9vaAWRjs6u/I4GYaME=
=HR3H
-----END PGP SIGNATURE-----
Merge tag 'multi-platform-for-3.7' of git://sources.calxeda.com/kernel/linux into next/multiplatform
Enable initial ARM multi-platform support for highbank, mvebu,
socfpga, picoxcell, and vexpress.
Multi-platform support is dependent on mach/gpio.h removal and
restructuring of DEBUG_LL and dtb build rules included in this branch.
This has been built for all defconfigs, and booted on highbank with
all 5 platforms enabled.
By Rob Herring (18) and Arnd Bergmann (1)
via Rob Herring
* tag 'multi-platform-for-3.7' of git://sources.calxeda.com/kernel/linux:
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
ARM: orion: move custom gpio functions to orion-gpio.h
ARM: shmobile: move custom gpio functions to sh-gpio.h
ARM: pxa: use gpio_to_irq for sharppm_sl
net: pxaficp_ir: add irq resources
usb: pxa27x_udc: remove IRQ_USB define
staging: ste_rmi4: remove gpio.h include
Conflicts due to addition of bcm2835 and removal of pnx4008 in:
arch/arm/Kconfig
arch/arm/Makefile
Conflicts due to new dtb targets, moved to arch/arm/boot/dts/Makefile in:
arch/arm/mach-imx/Makefile.boot
arch/arm/mach-mxs/Makefile.boot
arch/arm/mach-tegra/Makefile.boot
Signed-off-by: Olof Johansson <olof@lixom.net>
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
The branch is based on v3.6-rc6 in order to pick up a bug-fix to the
ASoC Tegra PCM driver that's required for audio to work correctly when
using dmaengine.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=4eRL
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup
ARM: tegra: switch to dmaengine
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
* tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ASoC: tegra: remove support of legacy DMA driver based access
spi: tegra: remove support of legacy DMA driver based access
ARM: tegra: apbio: remove support of legacy DMA driver based access
ARM: tegra: dma: remove legacy APB DMA driver
ARM: tegra: config: enable dmaengine based APB DMA driver
+ sync to 3.6-rc6
Jeff Kirsher says:
====================
This series contains updates to igb and ixgbevf.
v2: updated patch description in 04 patch (ixgbevf: scheduling while
atomic in reset hw path)
...
Akeem G. Abodunrin (1):
igb: Support to enable EEE on all eee_supported devices
Alexander Duyck (2):
igb: Remove artificial restriction on RQDPC stat reading
ixgbevf: Add support for VF API negotiation
John Fastabend (1):
ixgbevf: scheduling while atomic in reset hw path
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
we are currently returning ENODEV, as the clk_get may give a exact
error code in its returned pointer, assign it to the ret by using the
PTR_ERR function, so that the subsequent goto label will jump to the
error path and clean the driver and return the error correctly.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary temporary variable and #ifdef DEBUG block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the modes of Huawei E367 has this QMI/wwan interface:
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=07 Driver=(none)
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
Huawei use subclass and protocol to identify vendor specific
functions, so adding a new vendor rule for this combination.
The Pantech devices UML290 (106c:3718) and P4200 (106c:3721) use
the same subclass to identify the QMI/wwan function. Replace the
existing device specific UML290 entries with generic vendor matching,
adding support for the Pantech P4200.
The ZTE MF683 has 6 vendor specific interfaces, all using
ff/ff/ff for cls/sub/prot. Adding a match on interface #5 which
is a QMI/wwan interface.
Cc: Fangxiaozhi (Franko) <fangxiaozhi@huawei.com>
Cc: Thomas Schäfer <tschaefer@t-online.de>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Shawn J. Goff <shawn7400@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dbg() USB macro is so old, it predates me. The USB networking drivers are
the last hold-out using this macro, and we want to get rid of it, so replace
the usage of it with the proper netdev_dbg() or dev_dbg() (depending on the
context) calls.
Some places we end up using a local variable for the debug call, so also
convert the other existing dev_* calls to use it as well, to save tiny amounts
of code space.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
1. Extension to PPS/PTP to allow for PHC devices where pulses are
subject to a variable but measurable delay.
2. PPS/PTP/PHC support for Solarflare boards with a timestamping
peripheral.
3. MTD support for updating the timestamping peripheral on those boards.
4. Fix for potential over-length requests to firmware.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Before Emmanuel's change to use a copy of the command
("iwlwifi: get the correct HCMD in the response handler")
the iwl_add_sta_callback() function would have used a
random pointer to somewhere when processing responses
to an async command, while that wasn't valid data it
was at least a valid pointer. Now, the pointer will be
NULL in this case, thus crashing.
Fix this by exiting the function early if no command
is passed back which means it was sent asynchronously.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This change makes it so that the VF can support the PF/VF API negotiation
protocol. Specifically in this case we are adding support for API 1.0
which will mean that the VF is capable of cleaning up buffers that span
multiple descriptors without triggering an error.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Current implementation enables EEE on only i350 device. This patch enables
EEE on all eee_supported devices. Also, configured LPI clock to keep
running before EEE is enabled on i210 and i211 devices.
Signed-off-by: Akeem G. Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For some reason the reading of the RQDPC register was being artificially
limited to 4K. Instead of limiting the value we should read the value and
add the full amount. Otherwise this can lead to a misleading number of
dropped packets when the actual value is in fact much higher.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The r8169 driver currently limits the DMA burst for TX to 1024 bytes. I have
a box where this prevents the interface from using the gigabit line to its full
potential. This patch solves the problem by setting TX_DMA_BURST to unlimited.
The box has an ASRock B75M motherboard with on-board RTL8168evl/8111evl
(XID 0c900880). TSO is enabled.
I used netperf (TCP_STREAM test) to measure the dependency of TX throughput
on MTU. I did it for three different values of TX_DMA_BURST ('5'=512, '6'=1024,
'7'=unlimited). This chart shows the results:
http://michich.fedorapeople.org/r8169/r8169-effects-of-TX_DMA_BURST.png
Interesting points:
- With the current DMA burst limit (1024):
- at the default MTU=1500 I get only 842 Mbit/s.
- when going from small MTU, the performance rises monotonically with
increasing MTU only up to a peak at MTU=1076 (908 MBit/s). Then there's
a sudden drop to 762 MBit/s from which the throughput rises monotonically
again with further MTU increases.
- With a smaller DMA burst limit (512):
- there's a similar peak at MTU=1076 and another one at MTU=564.
- With unlimited DMA burst:
- at the default MTU=1500 I get nice 940 Mbit/s.
- the throughput rises monotonically with increasing MTU with no strange
peaks.
Notice that the peaks occur at MTU sizes that are multiples of the DMA burst
limit plus 52. Why 52? Because:
20 (IP header) + 20 (TCP header) + 12 (TCP options) = 52
The Realtek-provided r8168 driver (v8.032.00) uses unlimited TX DMA burst too,
except for CFG_METHOD_1 where the TX DMA burst is set to 512 bytes.
CFG_METHOD_1 appears to be the oldest MAC version of "RTL8168B/8111B",
i.e. RTL_GIGA_MAC_VER_11 in r8169. Not sure if this MAC version really needs
the smaller burst limit, or if any other versions have similar requirements.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal functions for add/deleting addresses don't change
their argument.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building 64-bit kernel with this driver we get following warnings from
the compiler:
drivers/net/ethernet/i825xx/znet.c: In function ‘hardware_init’:
drivers/net/ethernet/i825xx/znet.c:863:29: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/net/ethernet/i825xx/znet.c:870:29: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
Fix these by calling isa_virt_to_bus() before passing the pointers to
set_dma_addr().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ARM is moving to stricter checks on readl/write functions,
so we need to use the correct types everywhere.
Cc: netdev@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Instead of memcpy() from a static array, just use
the new helper function eth_broadcast_addr().
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
MCDI supports requests up to 252 bytes long, which is only enough to
pass 63 RX queue IDs to MC_CMD_FLUSH_RX_QUEUES. However a VF may have
up to 64 RX queues, and if we try to flush them all we will generate
an over-length request and BUG() in efx_mcdi_copyin(). Currently
all VF drivers limit themselves to 32 RX queues, so reducing the
limit to 63 does no harm.
Also add a BUILD_BUG_ON in efx_mcdi_flush_rxqs() so we remember to
deal with the same problem there if EFX_MAX_CHANNELS is increased.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
On big-endian systems the MTD partition names currently have mangled
subtype numbers and are not recognised by the firmware update tool
(sfupdate).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Add PTP IEEE-1588 support and make accesible via the PHC subsystem.
This work is based on prior code by Andrew Jackson
Signed-off-by: Stuart Hodgson <smhodgson@solarflare.com>
[bwh:
- Add byte order conversion in efx_ptp_send_times()
- Simplify conversion of PPS event times
- Add the built-in vs module check to CONFIG_SFC_PTP dependencies]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The maximum array sizes have been calculated on the basis of a maximum
SDU size of 255 bytes, whereas the actual maximum is 252 bytes.
Constructing a larger SDU will result in a BUG_ON in efx_mcdi_copyin.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
When the driver can't get the HW ready, we would release
the interrupt twice which made the kernel complain loudly.
Cc: stable@vger.kernel.org
Reported-by: Brian Cockrell <brian.cockrell@intel.com>
Tested-by: Brian Cockrell <brian.cockrell@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On PCI/PCI-X HW, if packet size is less than ETH_ZLEN,
packets may get corrupted during padding by HW.
To WA this issue, pad all small packets manually.
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a check if pdev->bus->self == NULL (root bus). When attaching
a netxen NIC to a VM it can be on the root bus and the guest would
crash in netxen_mask_aer_correctable() because of a NULL pointer
dereference if CONFIG_PCIEAER is present.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d6cb3e41 "bnx2x: fix checksum validation" caused a performance
regression for IPv6. Rx checksum offload does not work. IPv6 packets
are passed to the stack with CHECKSUM_NONE.
The hardware obviously cannot perform IP checksum validation for IPv6,
because there is no checksum in the IPv6 header. This should not prevent
us from setting CHECKSUM_UNNECESSARY.
Tested on BCM57711.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Couple more IPoIB fixes for regressions introduced by path database conversion
- Minor other fixes to low-level drivers (cxgb4, mlx4, qib, ocrdma)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=nqvR
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA fixes from Roland Dreier:
- A couple more IPoIB fixes for regressions introduced by path database
conversion
- Minor other fixes to low-level drivers (cxgb4, mlx4, qib, ocrdma)
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/qib: Fix failure of compliance test C14-024#06_LocalPortNum
RDMA/ocrdma: Fix CQE expansion of unsignaled WQE
mlx4_core: Fix integer overflows so 8TBs of memory registration works
IPoIB: Fix AB-BA deadlock when deleting neighbours
IPoIB: Fix memory leak in the neigh table deletion flow
RDMA/cxgb4: Move dereference below NULL test
Previously I210/I211 followed the same code flow as 82580/I350 for 1588.
However, since the register sets have changed, we must update the
implementation to accommodate the register changes.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In rare circumstances, it's possible a descriptor writeback will occur
before a timestamped Tx packet will go out on the wire, leading to the
driver believing the hardware failed to timestamp the packet. Schedule a
work item for 82576 and use the available time sync interrupt registers
on 82580 and above to account for this.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change the name of the adapter in the PTP struct to enable easier
correlation between interface and PTP device.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update ethtool_get_ts_info to not report any supported functionality on
82575 and add support for V2 Sync and V2 Delay packets. In the case
where CONFIG_IGB_PTP is not defined, we should be reporting default
values.
v2: Correct the function to return EOPNOTSUPP when there is no PTP support
or the device does not support PTP. Also fix minor whitespace issue.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Where possible, move PTP-related functions into igb_ptp.c and update the
names of functions and variables to match the established coding style
in the files and specify that they are PTP-specific.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For users without CONFIG_IGB_PTP=y, we should not be compiling any PTP
code into the driver. Tidy up the wrapping in igb to support this.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
John W. Linville says:
====================
This is another batch of updates intended for the 3.7 stream.
There are not a lot of large items, but iwlwifi, mwifiex, rt2x00,
ath9k, and brcmfmac all get some attention. Wei Yongjun also provides
a series of small maintenance fixes.
This also includes a pull of the wireless tree in order to satisfy
some prerequisites for later patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This part of the tty tree (unfortunately with all the preceding patches
as well) is a dependency for some of the OMAP cleanups, so we've pulled
it in as a dependency based on agreement with Greg.
Signed-off-by: Olof Johansson <olof@lixom.net>
Noticed that the byte and packet count statistics are under-
counting traffic handled by the DDP offload when there is more
than one DDP completion processed in a single call to
ixgbe_clean_rx_irq. This patch fixes that.
I tried to optimize the setting of the rss value so that it
only would have to be computed once, and only when there is
a DDP completion present.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Added the reg_ops file to debugfs with commands to read and write
a register to give users the ability to read and write individual
registers on the fly.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Added the netdev_ops file to debugfs with a command to call the
ndo_tx_timeout function to give users the ability to simulate a
tx_timeout call made by the kernel.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds debugfs support to the ixgbe driver to give
users the ability to access kernel information and to
simulate kernel events.
The filesystem is set up in the following driver/PCI-instance
hierarchy:
<debugfs>
|-- ixgbe
|-- PCI instance
| |-- attribute files
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
