* tmp-917a9:
ARM/vdso: Mark the vDSO code read-only after init
x86/vdso: Mark the vDSO code read-only after init
lkdtm: Verify that '__ro_after_init' works correctly
arch: Introduce post-init read-only memory
x86/mm: Always enable CONFIG_DEBUG_RODATA and remove the Kconfig option
mm/init: Add 'rodata=off' boot cmdline parameter to disable read-only kernel mappings
asm-generic: Consolidate mark_rodata_ro()
Linux 4.4.6
ld-version: Fix awk regex compile failure
target: Drop incorrect ABORT_TASK put for completed commands
block: don't optimize for non-cloned bio in bio_get_last_bvec()
MIPS: smp.c: Fix uninitialised temp_foreign_map
MIPS: Fix build error when SMP is used without GIC
ovl: fix getcwd() failure after unsuccessful rmdir
ovl: copy new uid/gid into overlayfs runtime inode
userfaultfd: don't block on the last VM updates at exit time
powerpc/powernv: Fix OPAL_CONSOLE_FLUSH prototype and usages
powerpc/powernv: Add a kmsg_dumper that flushes console output on panic
powerpc: Fix dedotify for binutils >= 2.26
Revert "drm/radeon/pm: adjust display configuration after powerstate"
drm/radeon: Fix error handling in radeon_flip_work_func.
drm/amdgpu: Fix error handling in amdgpu_flip_work_func.
Revert "drm/radeon: call hpd_irq_event on resume"
x86/mm: Fix slow_virt_to_phys() for X86_PAE again
gpu: ipu-v3: Do not bail out on missing optional port nodes
mac80211: Fix Public Action frame RX in AP mode
mac80211: check PN correctly for GCMP-encrypted fragmented MPDUs
mac80211: minstrel_ht: fix a logic error in RTS/CTS handling
mac80211: minstrel_ht: set default tx aggregation timeout to 0
mac80211: fix use of uninitialised values in RX aggregation
mac80211: minstrel: Change expected throughput unit back to Kbps
iwlwifi: mvm: inc pending frames counter also when txing non-sta
can: gs_usb: fixed disconnect bug by removing erroneous use of kfree()
cfg80211/wext: fix message ordering
wext: fix message delay/ordering
ovl: fix working on distributed fs as lower layer
ovl: ignore lower entries when checking purity of non-directory entries
ASoC: wm8958: Fix enum ctl accesses in a wrong type
ASoC: wm8994: Fix enum ctl accesses in a wrong type
ASoC: samsung: Use IRQ safe spin lock calls
ASoC: dapm: Fix ctl value accesses in a wrong type
ncpfs: fix a braino in OOM handling in ncp_fill_cache()
jffs2: reduce the breakage on recovery from halfway failed rename()
dmaengine: at_xdmac: fix residue computation
tracing: Fix check for cpu online when event is disabled
s390/dasd: fix diag 0x250 inline assembly
s390/mm: four page table levels vs. fork
KVM: MMU: fix reserved bit check for ept=0/CR0.WP=0/CR4.SMEP=1/EFER.NX=0
KVM: MMU: fix ept=0/pte.u=1/pte.w=0/CR0.WP=0/CR4.SMEP=1/EFER.NX=0 combo
KVM: PPC: Book3S HV: Sanitize special-purpose register values on guest exit
KVM: s390: correct fprs on SIGP (STOP AND) STORE STATUS
KVM: VMX: disable PEBS before a guest entry
kvm: cap halt polling at exactly halt_poll_ns
PCI: Allow a NULL "parent" pointer in pci_bus_assign_domain_nr()
ARM: OMAP2+: hwmod: Introduce ti,no-idle dt property
ARM: dts: dra7: do not gate cpsw clock due to errata i877
ARM: mvebu: fix overlap of Crypto SRAM with PCIe memory window
arm64: account for sparsemem section alignment when choosing vmemmap offset
Linux 4.4.5
drm/amdgpu: fix topaz/tonga gmc assignment in 4.4 stable
modules: fix longstanding /proc/kallsyms vs module insertion race.
drm/i915: refine qemu south bridge detection
drm/i915: more virtual south bridge detection
block: get the 1st and last bvec via helpers
block: check virt boundary in bio_will_gap()
drm/amdgpu: Use drm_calloc_large for VM page_tables array
thermal: cpu_cooling: fix out of bounds access in time_in_idle
i2c: brcmstb: allocate correct amount of memory for regmap
ubi: Fix out of bounds write in volume update code
cxl: Fix PSL timebase synchronization detection
MIPS: traps: Fix SIGFPE information leak from `do_ov' and `do_trap_or_bp'
MIPS: scache: Fix scache init with invalid line size.
USB: serial: option: add support for Quectel UC20
USB: serial: option: add support for Telit LE922 PID 0x1045
USB: qcserial: add Sierra Wireless EM74xx device ID
USB: qcserial: add Dell Wireless 5809e Gobi 4G HSPA+ (rev3)
USB: cp210x: Add ID for Parrot NMEA GPS Flight Recorder
usb: chipidea: otg: change workqueue ci_otg as freezable
ALSA: timer: Fix broken compat timer user status ioctl
ALSA: hdspm: Fix zero-division
ALSA: hdsp: Fix wrong boolean ctl value accesses
ALSA: hdspm: Fix wrong boolean ctl value accesses
ALSA: seq: oss: Don't drain at closing a client
ALSA: pcm: Fix ioctls for X32 ABI
ALSA: timer: Fix ioctls for X32 ABI
ALSA: rawmidi: Fix ioctls X32 ABI
ALSA: hda - Fix mic issues on Acer Aspire E1-472
ALSA: ctl: Fix ioctls for X32 ABI
ALSA: usb-audio: Add a quirk for Plantronics DA45
adv7604: fix tx 5v detect regression
dmaengine: pxa_dma: fix cyclic transfers
Fix directory hardlinks from deleted directories
jffs2: Fix page lock / f->sem deadlock
Revert "jffs2: Fix lock acquisition order bug in jffs2_write_begin"
Btrfs: fix loading of orphan roots leading to BUG_ON
pata-rb532-cf: get rid of the irq_to_gpio() call
tracing: Do not have 'comm' filter override event 'comm' field
ata: ahci: don't mark HotPlugCapable Ports as external/removable
PM / sleep / x86: Fix crash on graph trace through x86 suspend
arm64: vmemmap: use virtual projection of linear region
Adding Intel Lewisburg device IDs for SATA
writeback: flush inode cgroup wb switches instead of pinning super_block
block: bio: introduce helpers to get the 1st and last bvec
libata: Align ata_device's id on a cacheline
libata: fix HDIO_GET_32BIT ioctl
drm/amdgpu: return from atombios_dp_get_dpcd only when error
drm/amdgpu/gfx8: specify which engine to wait before vm flush
drm/amdgpu: apply gfx_v8 fixes to gfx_v7 as well
drm/amdgpu/pm: update current crtc info after setting the powerstate
drm/radeon/pm: update current crtc info after setting the powerstate
drm/ast: Fix incorrect register check for DRAM width
target: Fix WRITE_SAME/DISCARD conversion to linux 512b sectors
iommu/vt-d: Use BUS_NOTIFY_REMOVED_DEVICE in hotplug path
iommu/amd: Fix boot warning when device 00:00.0 is not iommu covered
iommu/amd: Apply workaround for ATS write permission check
arm/arm64: KVM: Fix ioctl error handling
KVM: x86: fix root cause for missed hardware breakpoints
vfio: fix ioctl error handling
Fix cifs_uniqueid_to_ino_t() function for s390x
CIFS: Fix SMB2+ interim response processing for read requests
cifs: fix out-of-bounds access in lease parsing
fbcon: set a default value to blink interval
kvm: x86: Update tsc multiplier on change.
mips/kvm: fix ioctl error handling
parisc: Fix ptrace syscall number and return value modification
PCI: keystone: Fix MSI code that retrieves struct pcie_port pointer
block: Initialize max_dev_sectors to 0
drm/amdgpu: mask out WC from BO on unsupported arches
btrfs: async-thread: Fix a use-after-free error for trace
btrfs: Fix no_space in write and rm loop
Btrfs: fix deadlock running delayed iputs at transaction commit time
drivers: sh: Restore legacy clock domain on SuperH platforms
use ->d_seq to get coherency between ->d_inode and ->d_flags
Linux 4.4.4
iwlwifi: mvm: don't allow sched scans without matches to be started
iwlwifi: update and fix 7265 series PCI IDs
iwlwifi: pcie: properly configure the debug buffer size for 8000
iwlwifi: dvm: fix WoWLAN
security: let security modules use PTRACE_MODE_* with bitmasks
IB/cma: Fix RDMA port validation for iWarp
x86/irq: Plug vector cleanup race
x86/irq: Call irq_force_move_complete with irq descriptor
x86/irq: Remove outgoing CPU from vector cleanup mask
x86/irq: Remove the cpumask allocation from send_cleanup_vector()
x86/irq: Clear move_in_progress before sending cleanup IPI
x86/irq: Remove offline cpus from vector cleanup
x86/irq: Get rid of code duplication
x86/irq: Copy vectormask instead of an AND operation
x86/irq: Check vector allocation early
x86/irq: Reorganize the search in assign_irq_vector
x86/irq: Reorganize the return path in assign_irq_vector
x86/irq: Do not use apic_chip_data.old_domain as temporary buffer
x86/irq: Validate that irq descriptor is still active
x86/irq: Fix a race in x86_vector_free_irqs()
x86/irq: Call chip->irq_set_affinity in proper context
x86/entry/compat: Add missing CLAC to entry_INT80_32
x86/mpx: Fix off-by-one comparison with nr_registers
hpfs: don't truncate the file when delete fails
do_last(): ELOOP failure exit should be done after leaving RCU mode
should_follow_link(): validate ->d_seq after having decided to follow
xen/pcifront: Fix mysterious crashes when NUMA locality information was extracted.
xen/pciback: Save the number of MSI-X entries to be copied later.
xen/pciback: Check PF instead of VF for PCI_COMMAND_MEMORY
xen/scsiback: correct frontend counting
xen/arm: correctly handle DMA mapping of compound pages
ARM: at91/dt: fix typo in sama5d2 pinmux descriptions
ARM: OMAP2+: Fix onenand initialization to avoid filesystem corruption
do_last(): don't let a bogus return value from ->open() et.al. to confuse us
kernel/resource.c: fix muxed resource handling in __request_region()
sunrpc/cache: fix off-by-one in qword_get()
tracing: Fix showing function event in available_events
powerpc/eeh: Fix partial hotplug criterion
KVM: x86: MMU: fix ubsan index-out-of-range warning
KVM: x86: fix conversion of addresses to linear in 32-bit protected mode
KVM: x86: fix missed hardware breakpoints
KVM: arm/arm64: vgic: Ensure bitmaps are long enough
KVM: async_pf: do not warn on page allocation failures
of/irq: Fix msi-map calculation for nonzero rid-base
NFSv4: Fix a dentry leak on alias use
nfs: fix nfs_size_to_loff_t
block: fix use-after-free in dio_bio_complete
bio: return EINTR if copying to user space got interrupted
i2c: i801: Adding Intel Lewisburg support for iTCO
phy: core: fix wrong err handle for phy_power_on
writeback: keep superblock pinned during cgroup writeback association switches
cgroup: make sure a parent css isn't offlined before its children
cpuset: make mm migration asynchronous
PCI/AER: Flush workqueue on device remove to avoid use-after-free
ARCv2: SMP: Emulate IPI to self using software triggered interrupt
ARCv2: STAR 9000950267: Handle return from intr to Delay Slot #2
libata: fix sff host state machine locking while polling
qla2xxx: Fix stale pointer access.
spi: atmel: fix gpio chip-select in case of non-DT platform
target: Fix race with SCF_SEND_DELAYED_TAS handling
target: Fix remote-port TMR ABORT + se_cmd fabric stop
target: Fix TAS handling for multi-session se_node_acls
target: Fix LUN_RESET active TMR descriptor handling
target: Fix LUN_RESET active I/O handling for ACK_KREF
ALSA: hda - Fixing background noise on Dell Inspiron 3162
ALSA: hda - Apply clock gate workaround to Skylake, too
Revert "workqueue: make sure delayed work run in local cpu"
workqueue: handle NUMA_NO_NODE for unbound pool_workqueue lookup
mac80211: Requeue work after scan complete for all VIF types.
rfkill: fix rfkill_fop_read wait_event usage
tick/nohz: Set the correct expiry when switching to nohz/lowres mode
perf stat: Do not clean event's private stats
cdc-acm:exclude Samsung phone 04e8:685d
Revert "Staging: panel: usleep_range is preferred over udelay"
Staging: speakup: Fix getting port information
sd: Optimal I/O size is in bytes, not sectors
libceph: don't spam dmesg with stray reply warnings
libceph: use the right footer size when skipping a message
libceph: don't bail early from try_read() when skipping a message
libceph: fix ceph_msg_revoke()
seccomp: always propagate NO_NEW_PRIVS on tsync
cpufreq: Fix NULL reference crash while accessing policy->governor_data
cpufreq: pxa2xx: fix pxa_cpufreq_change_voltage prototype
hwmon: (ads1015) Handle negative conversion values correctly
hwmon: (gpio-fan) Remove un-necessary speed_index lookup for thermal hook
hwmon: (dell-smm) Blacklist Dell Studio XPS 8000
Thermal: do thermal zone update after a cooling device registered
Thermal: handle thermal zone device properly during system sleep
Thermal: initialize thermal zone device correctly
IB/mlx5: Expose correct maximum number of CQE capacity
IB/qib: Support creating qps with GFP_NOIO flag
IB/qib: fix mcast detach when qp not attached
IB/cm: Fix a recently introduced deadlock
dmaengine: dw: disable BLOCK IRQs for non-cyclic xfer
dmaengine: at_xdmac: fix resume for cyclic transfers
dmaengine: dw: fix cyclic transfer callbacks
dmaengine: dw: fix cyclic transfer setup
nfit: fix multi-interface dimm handling, acpi6.1 compatibility
ACPI / PCI / hotplug: unlock in error path in acpiphp_enable_slot()
ACPI: Revert "ACPI / video: Add Dell Inspiron 5737 to the blacklist"
ACPI / video: Add disable_backlight_sysfs_if quirk for the Toshiba Satellite R830
ACPI / video: Add disable_backlight_sysfs_if quirk for the Toshiba Portege R700
lib: sw842: select crc32
uapi: update install list after nvme.h rename
ideapad-laptop: Add Lenovo Yoga 700 to no_hw_rfkill dmi list
ideapad-laptop: Add Lenovo ideapad Y700-17ISK to no_hw_rfkill dmi list
toshiba_acpi: Fix blank screen at boot if transflective backlight is supported
make sure that freeing shmem fast symlinks is RCU-delayed
drm/radeon/pm: adjust display configuration after powerstate
drm/radeon: Don't hang in radeon_flip_work_func on disabled crtc. (v2)
drm: Fix treatment of drm_vblank_offdelay in drm_vblank_on() (v2)
drm: Fix drm_vblank_pre/post_modeset regression from Linux 4.4
drm: Prevent vblank counter bumps > 1 with active vblank clients. (v2)
drm: No-Op redundant calls to drm_vblank_off() (v2)
drm/radeon: use post-decrement in error handling
drm/qxl: use kmalloc_array to alloc reloc_info in qxl_process_single_command
drm/i915: fix error path in intel_setup_gmbus()
drm/i915/dsi: don't pass arbitrary data to sideband
drm/i915/dsi: defend gpio table against out of bounds access
drm/i915/skl: Don't skip mst encoders in skl_ddi_pll_select()
drm/i915: Don't reject primary plane windowing with color keying enabled on SKL+
drm/i915/dp: fall back to 18 bpp when sink capability is unknown
drm/i915: Make sure DC writes are coherent on flush.
drm/i915: Init power domains early in driver load
drm/i915: intel_hpd_init(): Fix suspend/resume reprobing
drm/i915: Restore inhibiting the load of the default context
drm: fix missing reference counting decrease
drm/radeon: hold reference to fences in radeon_sa_bo_new
drm/radeon: mask out WC from BO on unsupported arches
drm: add helper to check for wc memory support
drm/radeon: fix DP audio support for APU with DCE4.1 display engine
drm/radeon: Add a common function for DFS handling
drm/radeon: cleaned up VCO output settings for DP audio
drm/radeon: properly byte swap vce firmware setup
drm/radeon: clean up fujitsu quirks
drm/radeon: Fix "slow" audio over DP on DCE8+
drm/radeon: call hpd_irq_event on resume
drm/radeon: Fix off-by-one errors in radeon_vm_bo_set_addr
drm/dp/mst: deallocate payload on port destruction
drm/dp/mst: Reverse order of MST enable and clearing VC payload table.
drm/dp/mst: move GUID storage from mgr, port to only mst branch
drm/dp/mst: Calculate MST PBN with 31.32 fixed point
drm: Add drm_fixp_from_fraction and drm_fixp2int_ceil
drm/dp/mst: fix in RAD element access
drm/dp/mst: fix in MSTB RAD initialization
drm/dp/mst: always send reply for UP request
drm/dp/mst: process broadcast messages correctly
drm/nouveau: platform: Fix deferred probe
drm/nouveau/disp/dp: ensure sink is powered up before attempting link training
drm/nouveau/display: Enable vblank irqs after display engine is on again.
drm/nouveau/kms: take mode_config mutex in connector hotplug path
drm/amdgpu/pm: adjust display configuration after powerstate
drm/amdgpu: Don't hang in amdgpu_flip_work_func on disabled crtc.
drm/amdgpu: use post-decrement in error handling
drm/amdgpu: fix issue with overlapping userptrs
drm/amdgpu: hold reference to fences in amdgpu_sa_bo_new (v2)
drm/amdgpu: remove unnecessary forward declaration
drm/amdgpu: fix s4 resume
drm/amdgpu: remove exp hardware support from iceland
drm/amdgpu: don't load MEC2 on topaz
drm/amdgpu: drop topaz support from gmc8 module
drm/amdgpu: pull topaz gmc bits into gmc_v7
drm/amdgpu: The VI specific EXE bit should only apply to GMC v8.0 above
drm/amdgpu: iceland use CI based MC IP
drm/amdgpu: move gmc7 support out of CIK dependency
drm/amdgpu: no need to load MC firmware on fiji
drm/amdgpu: fix amdgpu_bo_pin_restricted VRAM placing v2
drm/amdgpu: fix tonga smu resume
drm/amdgpu: fix lost sync_to if scheduler is enabled.
drm/amdgpu: call hpd_irq_event on resume
drm/amdgpu: Fix off-by-one errors in amdgpu_vm_bo_map
drm/vmwgfx: respect 'nomodeset'
drm/vmwgfx: Fix a width / pitch mismatch on framebuffer updates
drm/vmwgfx: Fix an incorrect lock check
virtio_pci: fix use after free on release
virtio_balloon: fix race between migration and ballooning
virtio_balloon: fix race by fill and leak
regulator: mt6311: MT6311_REGULATOR needs to select REGMAP_I2C
regulator: axp20x: Fix GPIO LDO enable value for AXP22x
clk: exynos: use irqsave version of spin_lock to avoid deadlock with irqs
cxl: use correct operator when writing pcie config space values
sparc64: fix incorrect sign extension in sys_sparc64_personality
EDAC, mc_sysfs: Fix freeing bus' name
EDAC: Robustify workqueues destruction
MIPS: Fix buffer overflow in syscall_get_arguments()
MIPS: Fix some missing CONFIG_CPU_MIPSR6 #ifdefs
MIPS: hpet: Choose a safe value for the ETIME check
MIPS: Loongson-3: Fix SMP_ASK_C0COUNT IPI handler
Revert "MIPS: Fix PAGE_MASK definition"
cputime: Prevent 32bit overflow in time[val|spec]_to_cputime()
time: Avoid signed overflow in timekeeping_get_ns()
Bluetooth: 6lowpan: Fix handling of uncompressed IPv6 packets
Bluetooth: 6lowpan: Fix kernel NULL pointer dereferences
Bluetooth: Fix incorrect removing of IRKs
Bluetooth: Add support of Toshiba Broadcom based devices
Bluetooth: Use continuous scanning when creating LE connections
Drivers: hv: vmbus: Fix a Host signaling bug
tools: hv: vss: fix the write()'s argument: error -> vss_msg
mmc: sdhci: Allow override of get_cd() called from sdhci_request()
mmc: sdhci: Allow override of mmc host operations
mmc: sdhci-pci: Fix card detect race for Intel BXT/APL
mmc: pxamci: fix again read-only gpio detection polarity
mmc: sdhci-acpi: Fix card detect race for Intel BXT/APL
mmc: mmci: fix an ages old detection error
mmc: core: Enable tuning according to the actual timing
mmc: sdhci: Fix sdhci_runtime_pm_bus_on/off()
mmc: mmc: Fix incorrect use of driver strength switching HS200 and HS400
mmc: sdio: Fix invalid vdd in voltage switch power cycle
mmc: sdhci: Fix DMA descriptor with zero data length
mmc: sdhci-pci: Do not default to 33 Ohm driver strength for Intel SPT
mmc: usdhi6rol0: handle NULL data in timeout
clockevents/tcb_clksrc: Prevent disabling an already disabled clock
posix-clock: Fix return code on the poll method's error path
irqchip/gic-v3-its: Fix double ICC_EOIR write for LPI in EOImode==1
irqchip/atmel-aic: Fix wrong bit operation for IRQ priority
irqchip/mxs: Add missing set_handle_irq()
irqchip/omap-intc: Add support for spurious irq handling
coresight: checking for NULL string in coresight_name_match()
dm: fix dm_rq_target_io leak on faults with .request_fn DM w/ blk-mq paths
dm snapshot: fix hung bios when copy error occurs
dm space map metadata: remove unused variable in brb_pop()
tda1004x: only update the frontend properties if locked
vb2: fix a regression in poll() behavior for output,streams
gspca: ov534/topro: prevent a division by 0
si2157: return -EINVAL if firmware blob is too big
media: dvb-core: Don't force CAN_INVERSION_AUTO in oneshot mode
rc: sunxi-cir: Initialize the spinlock properly
namei: ->d_inode of a pinned dentry is stable only for positives
mei: validate request value in client notify request ioctl
mei: fix fasync return value on error
rtlwifi: rtl8723be: Fix module parameter initialization
rtlwifi: rtl8188ee: Fix module parameter initialization
rtlwifi: rtl8192se: Fix module parameter initialization
rtlwifi: rtl8723ae: Fix initialization of module parameters
rtlwifi: rtl8192de: Fix incorrect module parameter descriptions
rtlwifi: rtl8192ce: Fix handling of module parameters
rtlwifi: rtl8192cu: Add missing parameter setup
rtlwifi: rtl_pci: Fix kernel panic
locks: fix unlock when fcntl_setlk races with a close
um: link with -lpthread
uml: fix hostfs mknod()
uml: flush stdout before forking
s390/fpu: signals vs. floating point control register
s390/compat: correct restore of high gprs on signal return
s390/dasd: fix performance drop
s390/dasd: fix refcount for PAV reassignment
s390/dasd: prevent incorrect length error under z/VM after PAV changes
s390: fix normalization bug in exception table sorting
btrfs: initialize the seq counter in struct btrfs_device
Btrfs: Initialize btrfs_root->highest_objectid when loading tree root and subvolume roots
Btrfs: fix transaction handle leak on failure to create hard link
Btrfs: fix number of transaction units required to create symlink
Btrfs: send, don't BUG_ON() when an empty symlink is found
btrfs: statfs: report zero available if metadata are exhausted
Btrfs: igrab inode in writepage
Btrfs: add missing brelse when superblock checksum fails
KVM: s390: fix memory overwrites when vx is disabled
s390/kvm: remove dependency on struct save_area definition
clocksource/drivers/vt8500: Increase the minimum delta
genirq: Validate action before dereferencing it in handle_irq_event_percpu()
mm: numa: quickly fail allocations for NUMA balancing on full nodes
mm: thp: fix SMP race condition between THP page fault and MADV_DONTNEED
ocfs2: unlock inode if deleting inode from orphan fails
drm/i915: shut up gen8+ SDE irq dmesg noise
iw_cxgb3: Fix incorrectly returning error on success
spi: omap2-mcspi: Prevent duplicate gpio_request
drivers: android: correct the size of struct binder_uintptr_t for BC_DEAD_BINDER_DONE
USB: option: add "4G LTE usb-modem U901"
USB: option: add support for SIM7100E
USB: cp210x: add IDs for GE B650V3 and B850V3 boards
usb: dwc3: Fix assignment of EP transfer resources
can: ems_usb: Fix possible tx overflow
dm thin: fix race condition when destroying thin pool workqueue
bcache: Change refill_dirty() to always scan entire disk if necessary
bcache: prevent crash on changing writeback_running
bcache: allows use of register in udev to avoid "device_busy" error.
bcache: unregister reboot notifier if bcache fails to unregister device
bcache: fix a leak in bch_cached_dev_run()
bcache: clear BCACHE_DEV_UNLINK_DONE flag when attaching a backing device
bcache: Add a cond_resched() call to gc
bcache: fix a livelock when we cause a huge number of cache misses
lib/ucs2_string: Correct ucs2 -> utf8 conversion
efi: Add pstore variables to the deletion whitelist
efi: Make efivarfs entries immutable by default
efi: Make our variable validation list include the guid
efi: Do variable name validation tests in utf8
efi: Use ucs2_as_utf8 in efivarfs instead of open coding a bad version
lib/ucs2_string: Add ucs2 -> utf8 helper functions
ARM: 8457/1: psci-smp is built only for SMP
drm/gma500: Use correct unref in the gem bo create function
devm_memremap: Fix error value when memremap failed
KVM: s390: fix guest fprs memory leak
arm64: errata: Add -mpc-relative-literal-loads to build flags
ARM: debug-ll: fix BCM63xx entry for multiplatform
ext4: fix bh->b_state corruption
sctp: Fix port hash table size computation
unix_diag: fix incorrect sign extension in unix_lookup_by_ino
tipc: unlock in error path
rtnl: RTM_GETNETCONF: fix wrong return value
IFF_NO_QUEUE: Fix for drivers not calling ether_setup()
tcp/dccp: fix another race at listener dismantle
route: check and remove route cache when we get route
net_sched fix: reclassification needs to consider ether protocol changes
pppoe: fix reference counting in PPPoE proxy
l2tp: Fix error creating L2TP tunnels
net/mlx4_en: Avoid changing dev->features directly in run-time
net/mlx4_en: Choose time-stamping shift value according to HW frequency
net/mlx4_en: Count HW buffer overrun only once
qmi_wwan: add "4G LTE usb-modem U901"
tcp: md5: release request socket instead of listener
tipc: fix premature addition of node to lookup table
af_unix: Guard against other == sk in unix_dgram_sendmsg
af_unix: Don't set err in unix_stream_read_generic unless there was an error
ipv4: fix memory leaks in ip_cmsg_send() callers
bonding: Fix ARP monitor validation
bpf: fix branch offset adjustment on backjumps after patching ctx expansion
flow_dissector: Fix unaligned access in __skb_flow_dissector when used by eth_get_headlen
net: Copy inner L3 and L4 headers as unaligned on GRE TEB
sctp: translate network order to host order when users get a hmacid
enic: increment devcmd2 result ring in case of timeout
tg3: Fix for tg3 transmit queue 0 timed out when too many gso_segs
net:Add sysctl_max_skb_frags
tcp: do not drop syn_recv on all icmp reports
unix: correctly track in-flight fds in sending process user_struct
ipv6: fix a lockdep splat
ipv6: addrconf: Fix recursive spin lock call
ipv6/udp: use sticky pktinfo egress ifindex on connect()
ipv6: enforce flowi6_oif usage in ip6_dst_lookup_tail()
tcp: beware of alignments in tcp_get_info()
switchdev: Require RTNL mutex to be held when sending FDB notifications
inet: frag: Always orphan skbs inside ip_defrag()
tipc: fix connection abort during subscription cancel
net: dsa: fix mv88e6xxx switches
sctp: allow setting SCTP_SACK_IMMEDIATELY by the application
pptp: fix illegal memory access caused by multiple bind()s
af_unix: fix struct pid memory leak
tcp: fix NULL deref in tcp_v4_send_ack()
lwt: fix rx checksum setting for lwt devices tunneling over ipv6
tunnels: Allow IPv6 UDP checksums to be correctly controlled.
net: dp83640: Fix tx timestamp overflow handling.
gro: Make GRO aware of lightweight tunnels.
af_iucv: Validate socket address length in iucv_sock_bind()
Conflicts:
arch/arm64/Makefile
arch/arm64/include/asm/cacheflush.h
drivers/mmc/host/sdhci.c
drivers/usb/dwc3/ep0.c
drivers/usb/dwc3/gadget.c
kernel/module.c
sound/core/pcm_compat.c
CRs-Fixed: 1010239
Signed-off-by: Runmin Wang <runminw@codeaurora.org>
Change-Id: I41a28636fc9ad91f9d979b191784609476294cdf
Currently kmemleak scans module memory as provided
in the area list. This takes up lot of time with
irq's and preemption disabled. Provide a compile
time configurable config to enable this functionality.
Change-Id: I5117705e7e6726acdf492e7f87c0703bc1f28da0
Signed-off-by: Vignesh Radhakrishnan <vigneshr@codeaurora.org>
Signed-off-by: Prasad Sodagudi <psodagud@codeaurora.org>
[satyap: trivial merge conflict resolution and remove duplicate entry]
Signed-off-by: Satya Durga Srinivasu Prabhala <satyap@codeaurora.org>
For CONFIG_KALLSYMS, we keep two symbol tables and two string tables.
There's one full copy, marked SHF_ALLOC and laid out at the end of the
module's init section. There's also a cut-down version that only
contains core symbols and strings, and lives in the module's core
section.
After module init (and before we free the module memory), we switch
the mod->symtab, mod->num_symtab and mod->strtab to point to the core
versions. We do this under the module_mutex.
However, kallsyms doesn't take the module_mutex: it uses
preempt_disable() and rcu tricks to walk through the modules, because
it's used in the oops path. It's also used in /proc/kallsyms.
There's nothing atomic about the change of these variables, so we can
get the old (larger!) num_symtab and the new symtab pointer; in fact
this is what I saw when trying to reproduce.
By grouping these variables together, we can use a
carefully-dereferenced pointer to ensure we always get one or the
other (the free of the module init section is already done in an RCU
callback, so that's safe). We allocate the init one at the end of the
module init section, and keep the core one inside the struct module
itself (it could also have been allocated at the end of the module
core, but that's probably overkill).
CRs-Fixed: 982779
Change-Id: I519f081967785e44a6ea33b16b1da64b14979963
Reported-by: Weilong Chen <chenweilong@huawei.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=111541
Cc: stable@kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Git-commit: 8244062ef1e54502ef55f54cced659913f244c3e
Git-repo: git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
[salvares@codeaurora.org: resolved context conflicts in module.c]
Signed-off-by: Sanrio Alvares <salvares@codeaurora.org>
commit 8244062ef1e54502ef55f54cced659913f244c3e upstream.
For CONFIG_KALLSYMS, we keep two symbol tables and two string tables.
There's one full copy, marked SHF_ALLOC and laid out at the end of the
module's init section. There's also a cut-down version that only
contains core symbols and strings, and lives in the module's core
section.
After module init (and before we free the module memory), we switch
the mod->symtab, mod->num_symtab and mod->strtab to point to the core
versions. We do this under the module_mutex.
However, kallsyms doesn't take the module_mutex: it uses
preempt_disable() and rcu tricks to walk through the modules, because
it's used in the oops path. It's also used in /proc/kallsyms.
There's nothing atomic about the change of these variables, so we can
get the old (larger!) num_symtab and the new symtab pointer; in fact
this is what I saw when trying to reproduce.
By grouping these variables together, we can use a
carefully-dereferenced pointer to ensure we always get one or the
other (the free of the module init section is already done in an RCU
callback, so that's safe). We allocate the init one at the end of the
module init section, and keep the core one inside the struct module
itself (it could also have been allocated at the end of the module
core, but that's probably overkill).
[ Rebased for 4.4-stable and older, because the following changes aren't
in the older trees:
- e0224418516b4d8a6c2160574bac18447c354ef0: adds arg to is_core_symbol
- 7523e4dc5057e157212b4741abd6256e03404cf1: module_init/module_core/init_size/core_size
become init_layout.base/core_layout.base/init_layout.size/core_layout.size.
]
Reported-by: Weilong Chen <chenweilong@huawei.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=111541
Cc: stable@kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4355efbd80482a961cae849281a8ef866e53d55c upstream.
Commit f2411da746 ("driver-core: add driver module
asynchronous probe support") added async probe support,
in two forms:
* in-kernel driver specification annotation
* generic async_probe module parameter (modprobe foo async_probe)
To support the generic kernel parameter parse_args() was
extended via commit ecc8617053 ("module: add extra
argument for parse_params() callback") however commit
failed to f2411da746 failed to add the required argument.
This causes a crash then whenever async_probe generic
module parameter is used. This was overlooked when the
form in which in-kernel async probe support was reworked
a bit... Fix this as originally intended.
Cc: Hannes Reinecke <hare@suse.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> [minimized]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e7bac536106236104e9e339531ff0fcdb7b8147 upstream.
This trivial wrapper adds clarity and makes the following patch
smaller.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the module init code fails after calling ftrace_module_init() and before
calling do_init_module(), we can suffer from a memory leak. This is because
ftrace_module_init() allocates pages to store the locations that ftrace
hooks are placed in the module text. If do_init_module() fails, it still
calls the MODULE_GOING notifiers which will tell ftrace to do a clean up of
the pages it allocated for the module. But if load_module() fails before
then, the pages allocated by ftrace_module_init() will never be freed.
Call ftrace_release_mod() on the module if load_module() fails before
getting to do_init_module().
Link: http://lkml.kernel.org/r/567CEA31.1070507@intel.com
Reported-by: "Qiu, PeiyangX" <peiyangx.qiu@intel.com>
Fixes: a949ae560a "ftrace/module: Hardcode ftrace_module_init() call into load_module()"
Cc: stable@vger.kernel.org # v2.6.38+
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Poma (on the way to another bug) reported an assertion triggering:
[<ffffffff81150529>] module_assert_mutex_or_preempt+0x49/0x90
[<ffffffff81150822>] __module_address+0x32/0x150
[<ffffffff81150956>] __module_text_address+0x16/0x70
[<ffffffff81150f19>] symbol_put_addr+0x29/0x40
[<ffffffffa04b77ad>] dvb_frontend_detach+0x7d/0x90 [dvb_core]
Laura Abbott <labbott@redhat.com> produced a patch which lead us to
inspect symbol_put_addr(). This function has a comment claiming it
doesn't need to disable preemption around the module lookup
because it holds a reference to the module it wants to find, which
therefore cannot go away.
This is wrong (and a false optimization too, preempt_disable() is really
rather cheap, and I doubt any of this is on uber critical paths,
otherwise it would've retained a pointer to the actual module anyway and
avoided the second lookup).
While its true that the module cannot go away while we hold a reference
on it, the data structure we do the lookup in very much _CAN_ change
while we do the lookup. Therefore fix the comment and add the
required preempt_disable().
Reported-by: poma <pomidorabelisima@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Fixes: a6e6abd575 ("module: remove module_text_address()")
Cc: stable@kernel.org
We don't actually hold the module_mutex when calling find_module_all
from module_kallsyms_lookup_name: that's because it's used by the oops
code and we don't want to deadlock.
However, access to the list read-only is safe if preempt is disabled,
so we can weaken the assertion. Keep a strong version for external
callers though.
Fixes: 0be964be0d ("module: Sanitize RCU usage and locking")
Reported-by: He Kuang <hekuang@huawei.com>
Cc: stable@kernel.org
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The load_module() error path frees a module but forgot to take it out
of the mod_tree, leaving a dangling entry in the tree, causing havoc.
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Reported-by: Arthur Marsh <arthur.marsh@internode.on.net>
Tested-by: Arthur Marsh <arthur.marsh@internode.on.net>
Fixes: 93c2e105f6 ("module: Optimize __module_address() using a latched RB-tree")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Main excitement here is Peter Zijlstra's lockless rbtree optimization to
speed module address lookup. He found some abusers of the module lock
doing that too.
A little bit of parameter work here too; including Dan Streetman's breaking
up the big param mutex so writing a parameter can load another module (yeah,
really). Unfortunately that broke the usual suspects, !CONFIG_MODULES and
!CONFIG_SYSFS, so those fixes were appended too.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVkgKHAAoJENkgDmzRrbjxQpwQAJVmBN6jF3SnwbQXv9vRixjH
58V33sb1G1RW+kXxQ3/e8jLX/4VaN479CufruXQp+IJWXsN/CH0lbC3k8m7u50d7
b1Zeqd/Yrh79rkc11b0X1698uGCSMlzz+V54Z0QOTEEX+nSu2ZZvccFS4UaHkn3z
rqDo00lb7rxQz8U25qro2OZrG6D3ub2q20TkWUB8EO4AOHkPn8KWP2r429Axrr0K
wlDWDTTt8/IsvPbuPf3T15RAhq1avkMXWn9nDXDjyWbpLfTn8NFnWmtesgY7Jl4t
GjbXC5WYekX3w2ZDB9KaT/DAMQ1a7RbMXNSz4RX4VbzDl+yYeSLmIh2G9fZb1PbB
PsIxrOgy4BquOWsJPm+zeFPSC3q9Cfu219L4AmxSjiZxC3dlosg5rIB892Mjoyv4
qxmg6oiqtc4Jxv+Gl9lRFVOqyHZrTC5IJ+xgfv1EyP6kKMUKLlDZtxZAuQxpUyxR
HZLq220RYnYSvkWauikq4M8fqFM8bdt6hLJnv7bVqllseROk9stCvjSiE3A9szH5
OgtOfYV5GhOeb8pCZqJKlGDw+RoJ21jtNCgOr6DgkNKV9CX/kL/Puwv8gnA0B0eh
dxCeB7f/gcLl7Cg3Z3gVVcGlgak6JWrLf5ITAJhBZ8Lv+AtL2DKmwEWS/iIMRmek
tLdh/a9GiCitqS0bT7GE
=tWPQ
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Main excitement here is Peter Zijlstra's lockless rbtree optimization
to speed module address lookup. He found some abusers of the module
lock doing that too.
A little bit of parameter work here too; including Dan Streetman's
breaking up the big param mutex so writing a parameter can load
another module (yeah, really). Unfortunately that broke the usual
suspects, !CONFIG_MODULES and !CONFIG_SYSFS, so those fixes were
appended too"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (26 commits)
modules: only use mod->param_lock if CONFIG_MODULES
param: fix module param locks when !CONFIG_SYSFS.
rcu: merge fix for Convert ACCESS_ONCE() to READ_ONCE() and WRITE_ONCE()
module: add per-module param_lock
module: make perm const
params: suppress unused variable error, warn once just in case code changes.
modules: clarify CONFIG_MODULE_COMPRESS help, suggest 'N'.
kernel/module.c: avoid ifdefs for sig_enforce declaration
kernel/workqueue.c: remove ifdefs over wq_power_efficient
kernel/params.c: export param_ops_bool_enable_only
kernel/params.c: generalize bool_enable_only
kernel/module.c: use generic module param operaters for sig_enforce
kernel/params: constify struct kernel_param_ops uses
sysfs: tightened sysfs permission checks
module: Rework module_addr_{min,max}
module: Use __module_address() for module_address_lookup()
module: Make the mod_tree stuff conditional on PERF_EVENTS || TRACING
module: Optimize __module_address() using a latched RB-tree
rbtree: Implement generic latch_tree
seqlock: Introduce raw_read_seqcount_latch()
...
As Dan Streetman points out, the entire point of locking for is to
stop sysfs accesses, so they're elided entirely in the !SYSFS case.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Here is the driver core / firmware changes for 4.2-rc1.
A number of small changes all over the place in the driver core, and in
the firmware subsystem. Nothing really major, full details in the
shortlog. Some of it is a bit of churn, given that the platform driver
probing changes was found to not work well, so they were reverted.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlWNoCQACgkQMUfUDdst+ym4JACdFrrXoMt2pb8nl5gMidGyM9/D
jg8AnRgdW8ArDA/xOarULd/X43eA3J3C
=Al2B
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the driver core / firmware changes for 4.2-rc1.
A number of small changes all over the place in the driver core, and
in the firmware subsystem. Nothing really major, full details in the
shortlog. Some of it is a bit of churn, given that the platform
driver probing changes was found to not work well, so they were
reverted.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (31 commits)
Revert "base/platform: Only insert MEM and IO resources"
Revert "base/platform: Continue on insert_resource() error"
Revert "of/platform: Use platform_device interface"
Revert "base/platform: Remove code duplication"
firmware: add missing kfree for work on async call
fs: sysfs: don't pass count == 0 to bin file readers
base:dd - Fix for typo in comment to function driver_deferred_probe_trigger().
base/platform: Remove code duplication
of/platform: Use platform_device interface
base/platform: Continue on insert_resource() error
base/platform: Only insert MEM and IO resources
firmware: use const for remaining firmware names
firmware: fix possible use after free on name on asynchronous request
firmware: check for file truncation on direct firmware loading
firmware: fix __getname() missing failure check
drivers: of/base: move of_init to driver_init
drivers/base: cacheinfo: fix annoying typo when DT nodes are absent
sysfs: disambiguate between "error code" and "failure" in comments
driver-core: fix build for !CONFIG_MODULES
driver-core: make __device_attach() static
...
"monitonic raw". Also some enhancements to make the ring buffer even
faster. But the biggest and most noticeable change is the renaming of
the ftrace* files, structures and variables that have to deal with
trace events.
Over the years I've had several developers tell me about their confusion
with what ftrace is compared to events. Technically, "ftrace" is the
infrastructure to do the function hooks, which include tracing and also
helps with live kernel patching. But the trace events are a separate
entity altogether, and the files that affect the trace events should
not be named "ftrace". These include:
include/trace/ftrace.h -> include/trace/trace_events.h
include/linux/ftrace_event.h -> include/linux/trace_events.h
Also, functions that are specific for trace events have also been renamed:
ftrace_print_*() -> trace_print_*()
(un)register_ftrace_event() -> (un)register_trace_event()
ftrace_event_name() -> trace_event_name()
ftrace_trigger_soft_disabled()-> trace_trigger_soft_disabled()
ftrace_define_fields_##call() -> trace_define_fields_##call()
ftrace_get_offsets_##call() -> trace_get_offsets_##call()
Structures have been renamed:
ftrace_event_file -> trace_event_file
ftrace_event_{call,class} -> trace_event_{call,class}
ftrace_event_buffer -> trace_event_buffer
ftrace_subsystem_dir -> trace_subsystem_dir
ftrace_event_raw_##call -> trace_event_raw_##call
ftrace_event_data_offset_##call-> trace_event_data_offset_##call
ftrace_event_type_funcs_##call -> trace_event_type_funcs_##call
And a few various variables and flags have also been updated.
This has been sitting in linux-next for some time, and I have not heard
a single complaint about this rename breaking anything. Mostly because
these functions, variables and structures are mostly internal to the
tracing system and are seldom (if ever) used by anything external to that.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJViYhVAAoJEEjnJuOKh9ldcJ0IAI+mytwoMAN/CWDE8pXrTrgs
aHlcr1zorSzZ0Lq6lKsWP+V0VGVhP8KWO16vl35HaM5ZB9U+cDzWiGobI8JTHi/3
eeTAPTjQdgrr/L+ZO1ApzS1jYPhN3Xi5L7xublcYMJjKfzU+bcYXg/x8gRt0QbG3
S9QN/kBt0JIIjT7McN64m5JVk2OiU36LxXxwHgCqJvVCPHUrriAdIX7Z5KRpEv13
zxgCN4d7Jiec/FsMW8dkO0vRlVAvudZWLL7oDmdsvNhnLy8nE79UOeHos2c1qifQ
LV4DeQ+2Hlu7w9wxixHuoOgNXDUEiQPJXzPc/CuCahiTL9N/urQSGQDoOVMltR4=
=hkdz
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"This patch series contains several clean ups and even a new trace
clock "monitonic raw". Also some enhancements to make the ring buffer
even faster. But the biggest and most noticeable change is the
renaming of the ftrace* files, structures and variables that have to
deal with trace events.
Over the years I've had several developers tell me about their
confusion with what ftrace is compared to events. Technically,
"ftrace" is the infrastructure to do the function hooks, which include
tracing and also helps with live kernel patching. But the trace
events are a separate entity altogether, and the files that affect the
trace events should not be named "ftrace". These include:
include/trace/ftrace.h -> include/trace/trace_events.h
include/linux/ftrace_event.h -> include/linux/trace_events.h
Also, functions that are specific for trace events have also been renamed:
ftrace_print_*() -> trace_print_*()
(un)register_ftrace_event() -> (un)register_trace_event()
ftrace_event_name() -> trace_event_name()
ftrace_trigger_soft_disabled() -> trace_trigger_soft_disabled()
ftrace_define_fields_##call() -> trace_define_fields_##call()
ftrace_get_offsets_##call() -> trace_get_offsets_##call()
Structures have been renamed:
ftrace_event_file -> trace_event_file
ftrace_event_{call,class} -> trace_event_{call,class}
ftrace_event_buffer -> trace_event_buffer
ftrace_subsystem_dir -> trace_subsystem_dir
ftrace_event_raw_##call -> trace_event_raw_##call
ftrace_event_data_offset_##call-> trace_event_data_offset_##call
ftrace_event_type_funcs_##call -> trace_event_type_funcs_##call
And a few various variables and flags have also been updated.
This has been sitting in linux-next for some time, and I have not
heard a single complaint about this rename breaking anything. Mostly
because these functions, variables and structures are mostly internal
to the tracing system and are seldom (if ever) used by anything
external to that"
* tag 'trace-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (33 commits)
ring_buffer: Allow to exit the ring buffer benchmark immediately
ring-buffer-benchmark: Fix the wrong type
ring-buffer-benchmark: Fix the wrong param in module_param
ring-buffer: Add enum names for the context levels
ring-buffer: Remove useless unused tracing_off_permanent()
ring-buffer: Give NMIs a chance to lock the reader_lock
ring-buffer: Add trace_recursive checks to ring_buffer_write()
ring-buffer: Allways do the trace_recursive checks
ring-buffer: Move recursive check to per_cpu descriptor
ring-buffer: Add unlikelys to make fast path the default
tracing: Rename ftrace_get_offsets_##call() to trace_event_get_offsets_##call()
tracing: Rename ftrace_define_fields_##call() to trace_event_define_fields_##call()
tracing: Rename ftrace_event_type_funcs_##call to trace_event_type_funcs_##call
tracing: Rename ftrace_data_offset_##call to trace_event_data_offset_##call
tracing: Rename ftrace_raw_##call event structures to trace_event_raw_##call
tracing: Rename ftrace_trigger_soft_disabled() to trace_trigger_soft_disabled()
tracing: Rename FTRACE_EVENT_FL_* flags to EVENT_FILE_FL_*
tracing: Rename struct ftrace_subsystem_dir to trace_subsystem_dir
tracing: Rename ftrace_event_name() to trace_event_name()
tracing: Rename FTRACE_MAX_EVENT to TRACE_EVENT_TYPE_MAX
...
Add a "param_lock" mutex to each module, and update params.c to use
the correct built-in or module mutex while locking kernel params.
Remove the kparam_block_sysfs_r/w() macros, replace them with direct
calls to kernel_param_[un]lock(module).
The kernel param code currently uses a single mutex to protect
modification of any and all kernel params. While this generally works,
there is one specific problem with it; a module callback function
cannot safely load another module, i.e. with request_module() or even
with indirect calls such as crypto_has_alg(). If the module to be
loaded has any of its params configured (e.g. with a /etc/modprobe.d/*
config file), then the attempt will result in a deadlock between the
first module param callback waiting for modprobe, and modprobe trying to
lock the single kernel param mutex to set the new module's param.
This fixes that by using per-module mutexes, so that each individual module
is protected against concurrent changes in its own kernel params, but is
not blocked by changes to other module params. All built-in modules
continue to use the built-in mutex, since they will always be loaded at
runtime and references (e.g. request_module(), crypto_has_alg()) to them
will never cause load-time param changing.
This also simplifies the interface used by modules to block sysfs access
to their params; while there are currently functions to block and unblock
sysfs param access which are split up by read and write and expect a single
kernel param to be passed, their actual operation is identical and applies
to all params, not just the one passed to them; they simply lock and unlock
the global param mutex. They are replaced with direct calls to
kernel_param_[un]lock(THIS_MODULE), which locks THIS_MODULE's param_lock, or
if the module is built-in, it locks the built-in mutex.
Suggested-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
There's no need to require an ifdef over the declaration
of sig_enforce as IS_ENABLED() can be used. While at it,
there's no harm in exposing this kernel parameter outside of
CONFIG_MODULE_SIG as it'd be a no-op on non module sig
kernels.
Now, technically we should in theory be able to remove
the #ifdef'ery over the declaration of the module parameter
as we are also trusting the bool_enable_only code for
CONFIG_MODULE_SIG kernels but for now remain paranoid
and keep it.
With time if no one can put a bullet through bool_enable_only
and if there are no technical requirements over not exposing
CONFIG_MODULE_SIG_FORCE with the measures in place by
bool_enable_only we could remove this last ifdef.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: linux-kernel@vger.kernel.org
Cc: cocci@systeme.lip6.fr
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This takes out the bool_enable_only implementation from
the module loading code and generalizes it so that others
can make use of it.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: linux-kernel@vger.kernel.org
Cc: cocci@systeme.lip6.fr
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We're directly checking and modifying sig_enforce when needed instead
of using the generic helpers. This prevents us from generalizing this
helper so that others can use it. Use indirect helpers to allow us
to generalize this code a bit and to make it a bit more clear what
this is doing.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: linux-kernel@vger.kernel.org
Cc: cocci@systeme.lip6.fr
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
__module_address() does an initial bound check before doing the
{list/tree} iteration to find the actual module. The bound variables
are nowhere near the mod_tree cacheline, in fact they're nowhere near
one another.
module_addr_min lives in .data while module_addr_max lives in .bss
(smarty pants GCC thinks the explicit 0 assignment is a mistake).
Rectify this by moving the two variables into a structure together
with the latch_tree_root to guarantee they all share the same
cacheline and avoid hitting two extra cachelines for the lookup.
While reworking the bounds code, move the bound update from allocation
to insertion time, this avoids updating the bounds for a few error
paths.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Use the generic __module_address() addr to struct module lookup
instead of open coding it once more.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Andrew worried about the overhead on small systems; only use the fancy
code when either perf or tracing is enabled.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Requested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Currently __module_address() is using a linear search through all
modules in order to find the module corresponding to the provided
address. With a lot of modules this can take a lot of time.
One of the users of this is kernel_text_address() which is employed
in many stack unwinders; which in turn are used by perf-callchain and
ftrace (possibly from NMI context).
So by optimizing __module_address() we optimize many stack unwinders
which are used by both perf and tracing in performance sensitive code.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Currently the RCU usage in module is an inconsistent mess of RCU and
RCU-sched, this is broken for CONFIG_PREEMPT where synchronize_rcu()
does not imply synchronize_sched().
Most usage sites use preempt_{dis,en}able() which is RCU-sched, but
(most of) the modification sites use synchronize_rcu(). With the
exception of the module bug list, which actually uses RCU.
Convert everything over to RCU-sched.
Furthermore add lockdep asserts to all sites, because it's not at all
clear to me the required locking is observed, esp. on exported
functions.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Some init systems may wish to express the desire to have device drivers
run their probe() code asynchronously. This implements support for this
and allows userspace to request async probe as a preference through a
generic shared device driver module parameter, async_probe.
Implementation for async probe is supported through a module parameter
given that since synchronous probe has been prevalent for years some
userspace might exist which relies on the fact that the device driver
will probe synchronously and the assumption that devices it provides
will be immediately available after this.
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The term "ftrace" is really the infrastructure of the function hooks,
and not the trace events. Rename ftrace_event.h to trace_events.h to
represent the trace_event infrastructure and decouple the term ftrace
from it.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The module notifier call chain for MODULE_STATE_COMING was moved up before
the parsing of args, into the complete_formation() call. But if the module failed
to load after that, the notifier call chain for MODULE_STATE_GOING was
never called and that prevented the users of those call chains from
cleaning up anything that was allocated.
Link: http://lkml.kernel.org/r/554C52B9.9060700@gmail.com
Reported-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Fixes: 4982223e51 "module: set nx before marking module MODULE_STATE_COMING"
Cc: stable@vger.kernel.org # 3.16+
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
but most architectures seem fixed now. Thanks to all involved.
Last minute rebase because I noticed a "[PATCH]" had snuck into a commit
message somehow.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=EYrW
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Quentin opened a can of worms by adding extable entry checking to
modpost, but most architectures seem fixed now. Thanks to all
involved.
Last minute rebase because I noticed a "[PATCH]" had snuck into a
commit message somehow"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
modpost: don't emit section mismatch warnings for compiler optimizations
modpost: expand pattern matching to support substring matches
modpost: do not try to match the SHT_NUL section.
modpost: fix extable entry size calculation.
modpost: fix inverted logic in is_extable_fault_address().
modpost: handle -ffunction-sections
modpost: Whitelist .text.fixup and .exception.text
params: handle quotes properly for values not of form foo="bar".
modpost: document the use of struct section_check.
modpost: handle relocations mismatch in __ex_table.
scripts: add check_extable.sh script.
modpost: mismatch_handler: retrieve tosym information only when needed.
modpost: factorize symbol pretty print in get_pretty_name().
modpost: add handler function pointer to sectioncheck.
modpost: add .sched.text and .kprobes.text to the TEXT_SECTIONS list.
modpost: add strict white-listing when referencing sections.
module: do not print allocation-fail warning on bogus user buffer size
kernel/module.c: fix typos in message about unused symbols
of the TRACE_DEFINE_ENUM() macro that can be used by tracepoints.
Tracepoints have helper functions for the TP_printk() called
__print_symbolic() and __print_flags() that lets a numeric number be
displayed as a a human comprehensible text. What is placed in the
TP_printk() is also shown in the tracepoint format file such that
user space tools like perf and trace-cmd can parse the binary data
and express the values too. Unfortunately, the way the TRACE_EVENT()
macro works, anything placed in the TP_printk() will be shown pretty
much exactly as is. The problem arises when enums are used. That's
because unlike macros, enums will not be changed into their values
by the C pre-processor. Thus, the enum string is exported to the
format file, and this makes it useless for user space tools.
The TRACE_DEFINE_ENUM() solves this by converting the enum strings
in the TP_printk() format into their number, and that is what is
shown to user space. For example, the tracepoint tlb_flush currently
has this in its format file:
__print_symbolic(REC->reason,
{ TLB_FLUSH_ON_TASK_SWITCH, "flush on task switch" },
{ TLB_REMOTE_SHOOTDOWN, "remote shootdown" },
{ TLB_LOCAL_SHOOTDOWN, "local shootdown" },
{ TLB_LOCAL_MM_SHOOTDOWN, "local mm shootdown" })
After adding:
TRACE_DEFINE_ENUM(TLB_FLUSH_ON_TASK_SWITCH);
TRACE_DEFINE_ENUM(TLB_REMOTE_SHOOTDOWN);
TRACE_DEFINE_ENUM(TLB_LOCAL_SHOOTDOWN);
TRACE_DEFINE_ENUM(TLB_LOCAL_MM_SHOOTDOWN);
Its format file will contain this:
__print_symbolic(REC->reason,
{ 0, "flush on task switch" },
{ 1, "remote shootdown" },
{ 2, "local shootdown" },
{ 3, "local mm shootdown" })
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVLBTuAAoJEEjnJuOKh9ldjHMIALdRS755TXCZGOf0r7O2akOR
wMPeum7C+ae1mH+jCsJKUC0/jUfQKaMt/UxoHlipDgcGg8kD2jtGnGCw4Xlwvdsr
y4rFmcTRSl1mo0zDSsg6ujoupHlVYN0+JPjrd7S3cv/llJoY49zcanNLF7S2XLeM
dZCtWRLWYpBiWO68ai6AqJTnE/eGFIqBI048qb5Eg8dbK243SSeSIf9Ywhb+VsA+
aq6F7cWI/H6j4tbeza8tAN19dcwenDro5EfCDY8ARQHJu1f6Y3+DLf2imjkd6Aiu
JVAoGIjHIpI+djwCZC1u4gi4urjfOqYartrM3Q54tb3YWYqHeNqP2ASI2a4EpYk=
=Ixwt
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"Some clean ups and small fixes, but the biggest change is the addition
of the TRACE_DEFINE_ENUM() macro that can be used by tracepoints.
Tracepoints have helper functions for the TP_printk() called
__print_symbolic() and __print_flags() that lets a numeric number be
displayed as a a human comprehensible text. What is placed in the
TP_printk() is also shown in the tracepoint format file such that user
space tools like perf and trace-cmd can parse the binary data and
express the values too. Unfortunately, the way the TRACE_EVENT()
macro works, anything placed in the TP_printk() will be shown pretty
much exactly as is. The problem arises when enums are used. That's
because unlike macros, enums will not be changed into their values by
the C pre-processor. Thus, the enum string is exported to the format
file, and this makes it useless for user space tools.
The TRACE_DEFINE_ENUM() solves this by converting the enum strings in
the TP_printk() format into their number, and that is what is shown to
user space. For example, the tracepoint tlb_flush currently has this
in its format file:
__print_symbolic(REC->reason,
{ TLB_FLUSH_ON_TASK_SWITCH, "flush on task switch" },
{ TLB_REMOTE_SHOOTDOWN, "remote shootdown" },
{ TLB_LOCAL_SHOOTDOWN, "local shootdown" },
{ TLB_LOCAL_MM_SHOOTDOWN, "local mm shootdown" })
After adding:
TRACE_DEFINE_ENUM(TLB_FLUSH_ON_TASK_SWITCH);
TRACE_DEFINE_ENUM(TLB_REMOTE_SHOOTDOWN);
TRACE_DEFINE_ENUM(TLB_LOCAL_SHOOTDOWN);
TRACE_DEFINE_ENUM(TLB_LOCAL_MM_SHOOTDOWN);
Its format file will contain this:
__print_symbolic(REC->reason,
{ 0, "flush on task switch" },
{ 1, "remote shootdown" },
{ 2, "local shootdown" },
{ 3, "local mm shootdown" })"
* tag 'trace-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (27 commits)
tracing: Add enum_map file to show enums that have been mapped
writeback: Export enums used by tracepoint to user space
v4l: Export enums used by tracepoints to user space
SUNRPC: Export enums in tracepoints to user space
mm: tracing: Export enums in tracepoints to user space
irq/tracing: Export enums in tracepoints to user space
f2fs: Export the enums in the tracepoints to userspace
net/9p/tracing: Export enums in tracepoints to userspace
x86/tlb/trace: Export enums in used by tlb_flush tracepoint
tracing/samples: Update the trace-event-sample.h with TRACE_DEFINE_ENUM()
tracing: Allow for modules to convert their enums to values
tracing: Add TRACE_DEFINE_ENUM() macro to map enums to their values
tracing: Update trace-event-sample with TRACE_SYSTEM_VAR documentation
tracing: Give system name a pointer
brcmsmac: Move each system tracepoints to their own header
iwlwifi: Move each system tracepoints to their own header
mac80211: Move message tracepoints to their own header
tracing: Add TRACE_SYSTEM_VAR to xhci-hcd
tracing: Add TRACE_SYSTEM_VAR to kvm-s390
tracing: Add TRACE_SYSTEM_VAR to intel-sst
...
Unlike most (all?) other copies from user space, kernel module loading
is almost unlimited in size. So we do a potentially huge
"copy_from_user()" when we copy the module data from user space to the
kernel buffer, which can be a latency concern when preemption is
disabled (or voluntary).
Also, because 'copy_from_user()' clears the tail of the kernel buffer on
failures, even a *failed* copy can end up wasting a lot of time.
Normally neither of these are concerns in real life, but they do trigger
when doing stress-testing with trinity. Running in a VM seems to add
its own overheadm causing trinity module load testing to even trigger
the watchdog.
The simple fix is to just chunk up the module loading, so that it never
tries to copy insanely big areas in one go. That bounds the latency,
and also the amount of (unnecessarily, in this case) cleared memory for
the failure case.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the infrastructure such that modules that declare TRACE_DEFINE_ENUM()
will have those enums converted into their values in the tracepoint
print fmt strings.
Link: http://lkml.kernel.org/r/87vbhjp74q.fsf@rustcorp.com.au
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
init_module(2) passes user-specified buffer length directly to
vmalloc(). It makes warn_alloc_failed() to print out a lot of info into
dmesg if user specified insane size, like -1.
Let's silence the warning. It doesn't add much value to -ENOMEM return
code. Without the patch the syscall is prohibitive noisy for testing
with trinity.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Module unload calls lockdep_free_key_range(), which removes entries
from the data structures. Most of the lockdep code OTOH assumes the
data structures are append only; in specific see the comments in
add_lock_to_list() and look_up_lock_class().
Clearly this has only worked by accident; make it work proper. The
actual scenario to make it go boom would involve the memory freed by
the module unlock being re-allocated and re-used for a lock inside of
a rcu-sched grace period. This is a very unlikely scenario, still
better plug the hole.
Use RCU list iteration in all places and ammend the comments.
Change lockdep_free_key_range() to issue a sync_sched() between
removal from the lists and returning -- which results in the memory
being freed. Further ensure the callers are placed correctly and
comment the requirements.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrey Tsyvarev <tsyvarev@ispras.ru>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Current approach in handling shadow memory for modules is broken.
Shadow memory could be freed only after memory shadow corresponds it is no
longer used. vfree() called from interrupt context could use memory its
freeing to store 'struct llist_node' in it:
void vfree(const void *addr)
{
...
if (unlikely(in_interrupt())) {
struct vfree_deferred *p = this_cpu_ptr(&vfree_deferred);
if (llist_add((struct llist_node *)addr, &p->list))
schedule_work(&p->wq);
Later this list node used in free_work() which actually frees memory.
Currently module_memfree() called in interrupt context will free shadow
before freeing module's memory which could provoke kernel crash.
So shadow memory should be freed after module's memory. However, such
deallocation order could race with kasan_module_alloc() in module_alloc().
Free shadow right before releasing vm area. At this point vfree()'d
memory is not used anymore and yet not available for other allocations.
New VM_KASAN flag used to indicate that vm area has dynamically allocated
shadow memory so kasan frees shadow only if it was previously allocated.
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When CONFIG_DEBUG_SET_MODULE_RONX is enabled, the sizes of
module sections are aligned up so appropriate permissions can
be applied. Adjusting for the symbol table may cause them to
become unaligned. Make sure to re-align the sizes afterward.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This provides a reliable breakpoint target, required for automatic symbol
loading via the gdb helper command 'lx-symbols'.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This feature let us to detect accesses out of bounds of global variables.
This will work as for globals in kernel image, so for globals in modules.
Currently this won't work for symbols in user-specified sections (e.g.
__init, __read_mostly, ...)
The idea of this is simple. Compiler increases each global variable by
redzone size and add constructors invoking __asan_register_globals()
function. Information about global variable (address, size, size with
redzone ...) passed to __asan_register_globals() so we could poison
variable's redzone.
This patch also forces module_alloc() to return 8*PAGE_SIZE aligned
address making shadow memory handling (
kasan_module_alloc()/kasan_module_free() ) more simple. Such alignment
guarantees that each shadow page backing modules address space correspond
to only one module_alloc() allocation.
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Konstantin Serebryany <kcc@google.com>
Cc: Dmitry Chernenkov <dmitryc@google.com>
Signed-off-by: Andrey Konovalov <adech.fo@gmail.com>
Cc: Yuri Gribov <tetra2005@gmail.com>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since the introduction of the nested sleep warning; we've established
that the occasional sleep inside a wait_event() is fine.
wait_event() loops are invariant wrt. spurious wakeups, and the
occasional sleep has a similar effect on them. As long as its occasional
its harmless.
Therefore replace the 'correct' but verbose wait_woken() thing with
a simple annotation to shut up the warning.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Because wait_event() loops are safe vs spurious wakeups we can allow the
occasional sleep -- which ends up being very similar.
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The warning message when loading modules with a wrong signature has
two spaces in it:
"module verification failed: signature and/or required key missing"
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
parse_args call module parameters' .set handlers, which may use locks defined in the module.
So, these classes should be freed in case parse_args returns error(e.g. due to incorrect parameter passed).
Signed-off-by: Andrey Tsyvarev <tsyvarev@ispras.ru>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
James Bottomley points out that it will be -1 during unload. It's
only used for diagnostics, so let's not hide that as it could be a
clue as to what's gone wrong.
Cc: Jason Wessel <jason.wessel@windriver.com>
Acked-and-documention-added-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Masami Hiramatsu <maasami.hiramatsu.pt@hitachi.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The kallsyms routines (module_symbol_name, lookup_module_* etc) disable
preemption to walk the modules rather than taking the module_mutex:
this is because they are used for symbol resolution during oopses.
This works because there are synchronize_sched() and synchronize_rcu()
in the unload and failure paths. However, there's one case which doesn't
have that: the normal case where module loading succeeds, and we free
the init section.
We don't want a synchronize_rcu() there, because it would slow down
module loading: this bug was introduced in 2009 to speed module
loading in the first place.
Thus, we want to do the free in an RCU callback. We do this in the
simplest possible way by allocating a new rcu_head: if we put it in
the module structure we'd have to worry about that getting freed.
Reported-by: Rui Xiang <rui.xiang@huawei.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Nothing needs the module pointer any more, and the next patch will
call it from RCU, where the module itself might no longer exist.
Removing the arg is the safest approach.
This just codifies the use of the module_alloc/module_free pattern
which ftrace and bpf use.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: x86@kernel.org
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: linux-cris-kernel@axis.com
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: nios2-dev@lists.rocketboards.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: sparclinux@vger.kernel.org
Cc: netdev@vger.kernel.org
Archs have been abusing module_free() to clean up their arch-specific
allocations. Since module_free() is also (ab)used by BPF and trace code,
let's keep it to simple allocations, and provide a hook called before
that.
This means that avr32, ia64, parisc and s390 no longer need to implement
their own module_free() at all. avr32 doesn't need module_finalize()
either.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-ia64@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Cc: linux-s390@vger.kernel.org
removal. This is possible by using a simple atomic_t for the counter,
rather than our fancy per-cpu counter: it turns out that no one is doing
a module increment per net packet, so the slowdown should be in the noise.
Also, script fixed for new git version.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=rDum
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"The exciting thing here is the getting rid of stop_machine on module
removal. This is possible by using a simple atomic_t for the counter,
rather than our fancy per-cpu counter: it turns out that no one is
doing a module increment per net packet, so the slowdown should be in
the noise"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
param: do not set store func without write perm
params: cleanup sysfs allocation
kernel:module Fix coding style errors and warnings.
module: Remove stop_machine from module unloading
module: Replace module_ref with atomic_t refcnt
lib/bug: Use RCU list ops for module_bug_list
module: Unlink module with RCU synchronizing instead of stop_machine
module: Wait for RCU synchronizing before releasing a module
