The ">" should be ">=" so that we don't read past the end of the array.
Fixes: 9d9a113e3695 ('Bluetooth: btusb: Add Realtek 8723A/8723B/8761A/8821A support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
ERROR: spaces required around that '<' (ctx:WxV)
+ if (err <0)
^
ERROR: code indent should use tabs where possible
+^I^I^I^I sizeof(ver));$
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Realtek ship a variety of bluetooth USB devices that identify
themselves with standard USB Bluetooth device class values, but
require a special driver to actually work. Without that driver,
you never get any scan results.
More recently however, Realtek appear to have wisened up and simply
posted a firmware update that makes these devices comply with
normal btusb protocols. The firmware needs to be uploaded on each boot.
Based on Realtek code from https://github.com/lwfinger/rtl8723au_bt
('new' branch).
This enables bluetooth support in the Gigabyte Brix GB-BXBT-2807 which
has this RTL8723BE USB device:
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 2.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3410 Rev= 2.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
There is no change to the USB descriptor after firmware update,
however the version read by HCI_OP_READ_LOCAL_VERSION changes from
0x8723 to 0x3083.
This has also been tested on RTL8723AE and RTL8821AE. Support for
RTL8761A has also been added, but that is untested.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Atheros support for missing the support for configuration of the
Bluetooth public address. Add support for the vendor specific command.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The driver callbacks in the Atheros support were all in a random order
and did not help readability of this driver. So reorder them to make
them aligned with what other Bluetooth UART drivers do. This patch is
not changing any actual code.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This isolates the Broadcom patchram download procedure as separate
function so that it can be easily used from USB and UART based drivers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
I think the comments are used to debug, and we don't need them in
mainline code
Signed-off-by: DingXiang <dingxiang@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Unregister GPIOs requested through sysfs at chip remove to avoid leaking
the associated memory and sysfs entries.
The stale sysfs entries prevented the gpio numbers from being exported
when the gpio range was later reused (e.g. at device reconnect).
This also fixes the related module-reference leak.
Note that kernfs makes sure that any on-going sysfs operations finish
before the class devices are unregistered and that further accesses
fail.
The chip exported flag is used to prevent gpiod exports during removal.
This also makes it harder to trigger, but does not fix, the related race
between gpiochip_remove and export_store, which is really a race with
gpiod_request that needs to be addressed separately.
Also note that this would prevent the crashes (e.g. NULL-dereferences)
at reconnect that affects pre-3.18 kernels, as well as use-after-free on
operations on open attribute files on pre-3.14 kernels (prior to
kernfs).
Fixes: d8f388d8dc ("gpio: sysfs interface")
Cc: stable <stable@vger.kernel.org> # v2.6.27: 01cca93a94
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
tcp_mark_lost_retrans is not used when FACK is disabled. Since
tcp_update_reordering may disable FACK, it should be called first
before tcp_mark_lost_retrans.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Congestion Control modules can provide per flow information,
but current way to get this information is to use netlink.
Like TCP_INFO, let's add TCP_CC_INFO so that applications can
issue a getsockopt() if they have a socket file descriptor,
instead of playing complex netlink games.
Sample usage would be :
union tcp_cc_info info;
socklen_t len = sizeof(info);
if (getsockopt(fd, SOL_TCP, TCP_CC_INFO, &info, &len) == -1)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We would like that optional info provided by Congestion Control
modules using netlink can also be read using getsockopt()
This patch changes get_info() to put this information in a buffer,
instead of skb, like tcp_get_info(), so that following patch
can reuse this common infrastructure.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch tracks total number of payload bytes received on a TCP socket.
This is the sum of all changes done to tp->rcv_nxt
RFC4898 named this : tcpEStatsAppHCThruOctetsReceived
This is a 64bit field, and can be fetched both from TCP_INFO
getsockopt() if one has a handle on a TCP socket, or from inet_diag
netlink facility (iproute2/ss patch will follow)
Note that tp->bytes_received was placed near tp->rcv_nxt for
best data locality and minimal performance impact.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Matt Mathis <mattmathis@google.com>
Cc: Eric Salo <salo@google.com>
Cc: Martin Lau <kafai@fb.com>
Cc: Chris Rapier <rapier@psc.edu>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch tracks total number of bytes acked for a TCP socket.
This is the sum of all changes done to tp->snd_una, and allows
for precise tracking of delivered data.
RFC4898 named this : tcpEStatsAppHCThruOctetsAcked
This is a 64bit field, and can be fetched both from TCP_INFO
getsockopt() if one has a handle on a TCP socket, or from inet_diag
netlink facility (iproute2/ss patch will follow)
Note that tp->bytes_acked was placed near tp->snd_una for
best data locality and minimal performance impact.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Cc: Matt Mathis <mattmathis@google.com>
Cc: Eric Salo <salo@google.com>
Cc: Martin Lau <kafai@fb.com>
Cc: Chris Rapier <rapier@psc.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
btrfs_release_extent_buffer_page() can't handle dummy extent that
allocated by btrfs_clone_extent_buffer() properly. That is because
reference count of pages that allocated by btrfs_clone_extent_buffer()
was 2, 1 by alloc_page(), and another by attach_extent_buffer_page().
Running following command repeatly can check this memory leak problem
btrfs inspect-internal inode-resolve 256 /mnt/btrfs
Signed-off-by: Chien-Kuan Yeh <ckya@synology.com>
Signed-off-by: Forrest Liu <forrestl@synology.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Tested-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Commit 6559a7e829 ("cxgb4: Cleanup macros so they follow the same
style and look consistent") introduced a regression where reading MC1
memory in adapters where MC0 isn't present or MC0 size is not equal to MC1
size caused the adapter to crash due to incorrect computation of memoffset.
Fix is to read the size of MC0 instead of MC1 for offset calculation
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a kdump environment interfaces might be re-loaded without a proper
unload sequence in the previous running kernel.
bnx2x management FW and driver maintains a `pulse' that notifies the FW
that the driver is still up and running.
Driver load on the kdump kernel should be performed only after the pulse
has been out-of-sync long enough for the management FW to identify that
the driver has crashed, on which point it will perform some necessary
cleanup of the HW.
In today's distros kdump loading is quite fast, sometimes too fast for our
FW to get out-of-sync. This patch delays the bnx2x's probe during kdump
to allow a proper re-load on the kdump kernel.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a Kernel Panic in bonding driver debugfs file: rlb_hash_table.
$> modprobe bonding mode=6
$> cat /sys/kernel/debug/bonding/bond0/rlb_hash_table
This will crash the kernel. The struct alb_bond_info is initialized only when
the bonding interface is initialized (ip link set bond0 up) and not at the time
it is allocated. If we try to read the table before that, it'll result in a
kernel panic.
The patch applies against both net and net-next
Signed-off-by: Vishwanath Pai <vpai@akamai.com>
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eeprom-length is a switch property, not a dsa property, and thus
needs to be attached to the switch node, not to the dsa node.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 6793abb4e8 ("net: dsa: Add support for switch EEPROM access")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under heavy Rx load, observed that the Hw is updating the USED bit
and it is not updating the received frame status to the BD control
field. This could be lack of resources for processing the BDs at high
data rates. Driver drops the frame associated with this BD but not
clearing the USED bit. So, this is causing hang condition as Hw
expects USED bit to be cleared for this BD.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b08cc79155 eliminated memory
allocation in the packet send path:
"hv_netvsc: Eliminate memory allocation in the packet send path
The network protocol used to communicate with the host is the remote ndis (rndis)
protocol. We need to decorate each outgoing packet with a rndis header and
additional rndis state (rndis per-packet state). To manage this state, we
currently allocate memory in the transmit path. Eliminate this allocation by
requesting additional head room in the skb."
This commit introduced a bug since it did not account for the case if the skb
was cloned. Fix this bug.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Tested-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Altera TSE MAC rx DMA transfer starts with the 2 additional bytes for IP
payload alignment. This patch fixes tse_rx() function loop which reads DMA
rx status and extracts packet length from it. Status signalises a whole DMA
transfer length, which is 2 bytes longer than the packet itself.
Signed-off-by: Vlastimil Setka <setka@vsis.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, the number of tx queues is limited by the number of online cpus
in mlx4_en_get_profile(). However, this limit no longer holds after the
ethtool .set_channels method has been called. In that situation, the driver
may access invalid bits of certain cpumask variables when queue_index >=
nr_cpu_ids.
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Acked-by: Ido Shamay <idos@mellanox.com>
Fixes: d03a68f ("net/mlx4_en: Configure the XPS queue mapping on driver load")
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we try to accumulate arrived packets in the links's
'deferred' queue during the parallel link syncronization phase.
This entails two problems:
- With an unlucky combination of arriving packets the algorithm
may go into a lockstep with the out-of-sequence handling function,
where the synch mechanism is adding a packet to the deferred queue,
while the out-of-sequence handling is retrieving it again, thus
ending up in a loop inside the node_lock scope.
- Even if this is avoided, the link will very often send out
unnecessary protocol messages, in the worst case leading to
redundant retransmissions.
We fix this by just dropping arriving packets on the upcoming link
during the synchronization phase, thus relying on the retransmission
protocol to resolve the situation once the two links have arrived to
a synchronized state.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.
Libraries like libnl will wait forever for NLMSG_DONE.
Fixes: 35b9dd7607 ("tipc: add bearer get/dump to new netlink api")
Fixes: 7be57fc691 ("tipc: add link get/dump to new netlink api")
Fixes: 46f15c6794 ("tipc: add media get/dump to new netlink api")
CC: Richard Alpe <richard.alpe@ericsson.com>
CC: Jon Maloy <jon.maloy@ericsson.com>
CC: Ying Xue <ying.xue@windriver.com>
CC: tipc-discussion@lists.sourceforge.net
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.
Libraries like libnl will wait forever for NLMSG_DONE.
Fixes: e5a55a8987 ("net: create generic bridge ops")
Fixes: 815cccbf10 ("ixgbe: add setlink, getlink support to ixgbe and ixgbevf")
CC: John Fastabend <john.r.fastabend@intel.com>
CC: Sathya Perla <sathya.perla@emulex.com>
CC: Subbu Seetharaman <subbu.seetharaman@emulex.com>
CC: Ajit Khaparde <ajit.khaparde@emulex.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: intel-wired-lan@lists.osuosl.org
CC: Jiri Pirko <jiri@resnulli.us>
CC: Scott Feldman <sfeldma@gmail.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: bridge@lists.linux-foundation.org
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.
Libraries like libnl will wait forever for NLMSG_DONE.
Fixes: 37a393bc49 ("bridge: notify mdb changes via netlink")
CC: Cong Wang <amwang@redhat.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: bridge@lists.linux-foundation.org
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This action is meant to be passive, i.e. we should not alter
skb->nfct: If nfct is present just leave it alone.
Compile tested only.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the 0x0x prefix in an integer constant.
In this case, while at it, also fix a typo (s/unitcast/unicast/).
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the 0x0x prefix in an integer constant.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <chris.snook@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Schmidt says:
====================
bnx2x: minor cleanups related to TPA bits
I noticed some simplification possibilities while looking into the bug
fixed by "bnx2x: really disable TPA if 'disable_tpa' is set'.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
These flags are redundant with dev->features. Remove them.
Just make sure to set dev->features ourselves in bnx2x_set_features()
before performing the reload of the card.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is simpler to have the TPA mode as one three-state variable.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If disable_tpa is set, remove NETIF_F_LRO from hw_features, so ethtool sees
it as "off [fixed]".
Note that setting the NETIF_F_LRO bit in dev->features in the 'else'
branch is not needed, because the bit was already set by
bnx2x_init_dev().
Then the check for disable_tpa in in bnx2x_fix_features() becomes unnecessary.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Introduce netif-msg to netvsc to control debug logging output
and keep msg_enable in netvsc_device_context so that it is
kept persistently.
2. Only call dump_rndis_message() when NETIF_MSG_RX_ERR or above
is specified in netvsc module debug param.
In non-debug mode, in current code, dump_rndis_message() will not
dump anything but it still initialize some local variables and
process the switch logic which is unnecessary, especially in
high network throughput situation.
Signed-off-by: Simon Xiao <sixiao@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 3cdaa5be9e ("ipv4: Don't
increase PMTU with Datagram Too Big message") broke PMTU in cases
where the rt_pmtu value has expired but is smaller than the new
PMTU value.
This obsolete rt_pmtu then prevents the new PMTU value from being
installed.
Fixes: 3cdaa5be9e ("ipv4: Don't increase PMTU with Datagram Too Big message")
Reported-by: Gerd v. Egidy <gerd.von.egidy@intra2net.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
__dma_alloc() does a PAGE_ALIGN() on the passed in size argument before
doing anything else. __dma_free() does not. And because it doesn't, it is
possible to leak memory should size not be an integer multiple of PAGE_SIZE.
The solution is to add a PAGE_ALIGN() to __dma_free() like is done in
__dma_alloc().
Additionally, this patch removes a redundant PAGE_ALIGN() from
__dma_alloc_coherent(), since __dma_alloc_coherent() can only be called
from __dma_alloc(), which already does a PAGE_ALIGN() before the call.
Cc: stable@vger.kernel.org
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The variable for the 'permissive' module parameter used to be static
but was recently changed to be extern. This puts it in the kernel
global namespace if the driver is built-in, so its name should begin
with a prefix identifying the driver.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: af6fc858a3 ("xen-pciback: limit guest control of command register")
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Commit 77e32c89a7 ("clockevents: Manage device's state separately for
the core") decouples clockevent device's modes from states. With this
change when a Xen guest tries to resume, it won't be calling its
set_mode op which needs to be done on each VCPU in order to make the
hypervisor aware that we are in oneshot mode.
This happens because clockevents_tick_resume() (which is an intermediate
step of resuming ticks on a processor) doesn't call clockevents_set_state()
anymore and because during suspend clockevent devices on all VCPUs (except
for the one doing the suspend) are left in ONESHOT state. As result, during
resume the clockevents state machine will assume that device is already
where it should be and doesn't need to be updated.
To avoid this problem we should suspend ticks on all VCPUs during
suspend.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Commit 335f49196f (sched/idle: Use explicit broadcast oneshot
control function) replaced clockevents_notify() invocations in
cpuidle_idle_call() with direct calls to tick_broadcast_enter()
and tick_broadcast_exit(), but it overlooked the fact that
interrupts were already enabled before calling the latter which
led to functional breakage on systems using idle states with the
CPUIDLE_FLAG_TIMER_STOP flag set.
Fix that by moving the invocations of tick_broadcast_enter()
and tick_broadcast_exit() down into cpuidle_enter_state() where
interrupts are still disabled when tick_broadcast_exit() is
called. Also ensure that interrupts will be disabled before
running tick_broadcast_exit() even if they have been enabled by
the idle state's ->enter callback. Trigger a WARN_ON_ONCE() in
that case, as we generally don't want that to happen for states
with CPUIDLE_FLAG_TIMER_STOP set.
Fixes: 335f49196f (sched/idle: Use explicit broadcast oneshot control function)
Reported-and-tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reported-and-tested-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
DMIC clock source is not from codec system clock directly. it is
generated from the division of system clock. And it should be 256 *
sample rate of AIF1.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Channels allocated via dma_get_any_slave_channel were not increasing
the counter tracking private allocations. When these channels were
released, privatecnt may erroneously fall to zero. The DMA device
would then lose its DMA_PRIVATE cap and fail to allocate future private
channels (via private_candidate) as any allocations still outstanding
would incorrectly be seen as public allocations.
Signed-off-by: Christopher Freeman <cfreeman@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Samsung has just released a portable USB3 SSD, coming in a very small
and nice form factor. It's USB ID is 04e8:8001, which unfortunately is
already used by the Palm Visor driver for the Samsung I330 phone cradle.
Having pl2303 or visor pick up this device ID results in conflicts with
the usb-storage driver, which handles the newly released portable USB3
SSD.
To work around this conflict, I've dug up a mailing list post [1] from a
long time ago, in which a user posts the full USB descriptor
information. The most specific value in this appears to be the interface
class, which has value 255 (0xff). Since usb-storage requires an
interface class of 0x8, I believe it's correct to disambiguate the two
devices by matching on 0xff inside visor.
[1] http://permalink.gmane.org/gmane.linux.usb.user/4264
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This phone is already supported by the visor driver.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Added the USB serial console device ID for KCF Technologies PRN device
which has a USB port for its serial console.
Signed-off-by: Mark Edwards <sonofaforester@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
