Linux-next has failed to compile for kirkwood since 23 August with:
arch/arm/mach-kirkwood/db88f6281-bp-setup.c:29: error: 'SZ_1M' undeclared here (not in a function)
arch/arm/mach-kirkwood/db88f6281-bp-setup.c:33: error: 'SZ_4M' undeclared here (not in a function)
Add missing <linux/sizes.h>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
renesas_usbhs driver can play role as both Host and Gadget.
In case of Gadget, it requires not only renesas_usbhs
but also usb gadget module (like g_ether).
So, renesas_usbhs driver calls usb_add_gadget_udc() on probe time.
Because of this behavior,
Host port plays also Gadget role if kernel has both Host/Gadget support.
In mackerel case, from 0ada2da518
(ARM: mach-shmobile: mackerel: use renesas_usbhs instead of r8a66597_hcd)
usb0 plays Gadget role, and usb1 plays Host role,
and current mackerel board probes as usb1 -> usb0.
Thus, 1st installed usb gadget module (like g_ether) will be
assigned to usb1 (= usb Host port), and 2nd module to usb0 (= usb Gadget port).
It is very confusable for user.
This patch fixup usb modes probing order as usb0 -> usb1.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Since armadillo800eva has 2 sound cards,
and had reversed deferred probe order issue,
it was purposely registered in reverse order.
But it was solved by
1d29cfa574
(driver core: fixup reversed deferred probe order)
armadillo800eva board is expecting that
FSI-WM8978 is the 1st, and FSI-HDMI is the 2nd sound card.
This patch fixes it up
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Fix inconsistency between mach-types and CONFIG_ name that prevents
touchbook board from booting.
Signed-off-by: Radek Pilar <mrkva@mrkva.eu>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In some OMAP3 HS devices (at least Nokia N9 and N950), the public SRAM
seems to conflict with secure portition of SRAM. When booting the 3.6-rc3
kernel (and also earlier) on these devices, the kernel gets tainted with
tons of the following warnings:
[ 6.894348] In-band Error seen by MPU at address 0
[...]
[ 6.894378] WARNING: at arch/arm/mach-omap2/omap_l3_smx.c:162
Fix this by skipping the first 16K of the public SRAM. (Note that the
mapping could not be changed, as it resulted in secure monitor call
failure in save_secure_sram().)
This will leave 12K SRAM available that should be still sufficient. The
patch has been boot tested with vanilla 3.6-rc3 on N900, N950 and N9.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4-specific code should be executed only if we are running on
OMAP4. Otherwise it may break multi-OMAP kernels. Found by reading
the code.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently, omap2_sync32k_clocksource_init() function initializes the 32K
timer as the system clock source regardless of the CONFIG_OMAP_32K_TIMER
setting.
Fix this by providing a default implementation for
!CONFIG_OMAP_32K_TIMER case.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
dummy_supplies for smsc911x are registered as "smsc911x".
smsc911x driver needs id = -1
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Make use of the same atomic pool as DMA does, and skip a kernel page
mapping which can involve sleep'able operations at allocating a kernel
page table.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Support atomic allocation in __iommu_get_pages().
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
[moved __atomic_get_pages() under #ifdef CONFIG_ARM_DMA_USE_IOMMU
to avoid unused fuction warning for no-IOMMU case]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Check the given range("start", "size") is included in "atomic_pool" or not.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
struct page **pages is necessary to align with non atomic path in
__iommu_get_pages(). atomic_pool() has the intialized **pages instead
of just *page.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
The default 256 KiB coherent pool may be too small for some of the Kirkwood
devices, so increase it to make sure that devices will be able to allocate
their buffers with GFP_ATOMIC flag.
Suggested-by: Josh Coombs <josh.coombs@gmail.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Print a loud warning when system runs out of memory from atomic DMA
coherent pool to let users notice the potential problem.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Some platforms might require to increase atomic coherent pool to make
sure that their device will be able to allocate all their buffers from
atomic context. This function can be also used to decrease atomic
coherent pool size if coherent allocations are not used for the given
sub-platform.
Suggested-by: Josh Coombs <josh.coombs@gmail.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Contiguous Memory Allocator requires only paging and MMU enabled not
particular CPU architectures, so there is no need for strict dependency
on CPU type. This enables to use CMA on some older ARM v5 systems which
also might need large contiguous blocks for the multimedia processing hw
modules.
Reported-by: Prabhakar Lad <prabhakar.lad@ti.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Prabhakar Lad <prabhakar.lad@ti.com>
- move to sparse IRQ: some drivers were forgotten
- a DTS typo
- the delay for removal of old at91_mci driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQOykiAAoJEAf03oE53VmQS0MIALb4N+yRt6+Y3hjvFT386bYb
aA24NJRRn3Lsyldc7lDpKQPsAUdlPWGp6SNdUlfSFFerI2tEtwzCKkSpvN/4vH6f
e5LtlGSRKrzzDjaKl9cLJOKwm2rGPC37VjmdqFE4Mfcl3YzFGKLpvevq8uMBTCEz
6GnODy7njBk62Zzky0NR4SOgrPdI9EO5XZijXWXCfwW6MHjxRBRZf+Hn+LcJvQ5N
gLZfgMCtebsjb2x1pYP+4NfBQQLpx+sHy4on5IPlp1fEYaIaMXKCFGQNhTRqKSSD
xSpBRV/XmzmAWvffQJiiRYR4CG6lKwvhGhuxBUn5z7dRIcSoiRQKB7oISWITZs4=
=Itki
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes' of git://github.com/at91linux/linux-at91 into fixes
Fixes for AT91 related to:
- move to sparse IRQ: some drivers were forgotten
- a DTS typo
- the delay for removal of old at91_mci driver
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91/feature-removal-schedule: delay at91_mci removal
ARM: at91/dts: remove partial parameter in at91sam9g25ek.dts
ARM: at91/clock: fix PLLA overclock warning
ARM: at91: fix rtc-at91sam9 irq issue due to sparse irq support
ARM: at91: fix system timer irq issue due to sparse irq support
Bug fixes for various ARM platforms. About half of these are
for OMAP and submitted before but did not make it into v3.6-rc2.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Tupl
-----END PGP SIGNATURE-----
Merge tag 'fixes-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc fixes from Arnd Bergmann:
"Bug fixes for various ARM platforms. About half of these are for OMAP
and submitted before but did not make it into v3.6-rc2."
* tag 'fixes-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
ARM: ux500: don't select LEDS_GPIO for snowball
ARM: imx: build i.MX6 functions only when needed
ARM: imx: select CPU_FREQ_TABLE when needed
ARM: imx: fix ksz9021rn_phy_fixup
ARM: imx: build pm-imx5 code only when PM is enabled
ARM: omap: allow building omap44xx without SMP
ARM: dts: imx51-babbage: fix esdhc cd/wp properties
ARM: imx6: spin the cpu until hardware takes it down
ARM: ux500: Ensure probing of Audio devices when Device Tree is enabled
ARM: ux500: Fix merge error, no matching driver name for 'snd_soc_u8500'
ARM i.MX6q: Add virtual 1/3.5 dividers in the LDB clock path
ARM: Kirkwood: fix Makefile.boot
ARM: Kirkwood: Fix iconnect leds
ARM: Orion: Set eth packet size csum offload limit
ARM: mv78xx0: fix win_cfg_base prototype
ARM: OMAP: dmtimers: Fix locking issue in omap_dm_timer_request*()
ARM: mmp: fix potential NULL dereference
ARM: OMAP4: Register the OPP table only for 4430 device
cpufreq: OMAP: Handle missing frequency table on SMP systems
ARM: OMAP4: sleep: Save the complete used register stack frame
...
With !HIGHMEM, sanity_check_meminfo checks for banks that completely or
partially overlap the vmalloc region. The test for partial overlap checks
__va(bank->start + bank->size) > vmalloc_min. This is not appropriate if
there is a non-linear translation between virtual and physical addresses,
as bank->start + bank->size is actually in the bank following the one being
interrogated.
In most cases, even when using SPARSEMEM, this is not problematic as the
subsequent bank will start at a higher va than the one in question. However
if the physical to virtual address conversion is not monotonic increasing,
the incorrect test could result in a bank not being truncated when it
should be.
This patch ensures we perform the va-pa conversion on memory from the
bank we are interested in, not the following one.
Reported-by: ??? (Steve) <zhanzhenbo@gmail.com>
Signed-off-by: Jonathan Austin <jonathan.austin@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
LPAE does not use two pmd entries for a pte, so the additional tlb
flushing is not required.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The bfi instruction is not available on ARMv6, so instead use an and/orr
sequence in the contextidr_notifier. This gets rid of the assembler
error:
Assembler messages:
Error: selected processor does not support ARM mode `bfi r3,r2,#0,#8'
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When enabling the MMU for ARMv7 CPUs, the decompressor does not touch
the ttbcr register, assuming that it will be zeroed (N == 0, EAE == 0).
Given that only EAE is defined as 0 for non-secure copies of the
register (and a bootloader such as kexec may leave it set to 1 anyway),
we should ensure that we reset the register ourselves before turning on
the MMU.
This patch zeroes TTBCR.EAE and TTBCR.N prior to enabling the MMU for
ARMv7 cores in the decompressor, configuring us exclusively for 32-bit
translation tables via TTBR0.
Cc: <stable@vger.kernel.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Matthew Leach <matthew.leach@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Breakpoint validation currently fails for single-byte watchpoints on
addresses ending in 11b. There is no reason to forbid such a watchpoint,
so extend the validation code to allow it.
Cc: Ulrich Weigand <Ulrich.Weigand@de.ibm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From ARM debug architecture v7.1 onwards, a watchpoint exception causes
the DFAR to be updated with the faulting data address. However, DFSR.WnR
takes an UNKNOWN value and therefore cannot be used in general to
determine the access type that triggered the watchpoint.
This patch forbids watchpoints without an overflow handler from
specifying a specific access type (load/store). Those with overflow
handlers must be able to handle false positives potentially triggered by
a watchpoint of a different access type on the same address. For
SIGTRAP-based handlers (i.e. ptrace), this should have no impact.
Cc: <stable@vger.kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Murali Nalajala reports a regression that ioremapping address zero
results in an oops dump:
Unable to handle kernel paging request at virtual address fa200000
pgd = d4f80000
[fa200000] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 Tainted: G W (3.4.0-g3b5f728-00009-g638207a #13)
PC is at msm_pm_config_rst_vector_before_pc+0x8/0x30
LR is at msm_pm_boot_config_before_pc+0x18/0x20
pc : [<c0078f84>] lr : [<c007903c>] psr: a0000093
sp : c0837ef0 ip : cfe00000 fp : 0000000d
r10: da7efc17 r9 : 225c4278 r8 : 00000006
r7 : 0003c000 r6 : c085c824 r5 : 00000001 r4 : fa101000
r3 : fa200000 r2 : c095080c r1 : 002250fc r0 : 00000000
Flags: NzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c5387d Table: 25180059 DAC: 00000015
[<c0078f84>] (msm_pm_config_rst_vector_before_pc+0x8/0x30) from [<c007903c>] (msm_pm_boot_config_before_pc+0x18/0x20)
[<c007903c>] (msm_pm_boot_config_before_pc+0x18/0x20) from [<c007a55c>] (msm_pm_power_collapse+0x410/0xb04)
[<c007a55c>] (msm_pm_power_collapse+0x410/0xb04) from [<c007b17c>] (arch_idle+0x294/0x3e0)
[<c007b17c>] (arch_idle+0x294/0x3e0) from [<c000eed8>] (default_idle+0x18/0x2c)
[<c000eed8>] (default_idle+0x18/0x2c) from [<c000f254>] (cpu_idle+0x90/0xe4)
[<c000f254>] (cpu_idle+0x90/0xe4) from [<c057231c>] (rest_init+0x88/0xa0)
[<c057231c>] (rest_init+0x88/0xa0) from [<c07ff890>] (start_kernel+0x3a8/0x40c)
Code: c0704256 e12fff1e e59f2020 e5923000 (e5930000)
This is caused by the 'reserved' entries which we insert (see
19b52abe3c - ARM: 7438/1: fill possible PMD empty section gaps)
which get matched for physical address zero.
Resolve this by marking these reserved entries with a different flag.
Cc: <stable@vger.kernel.org>
Tested-by: Murali Nalajala <mnalajal@codeaurora.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The GPIO buttons are named SW3, SW4, SW5 and SW6 on the board
silkscreen. Update the buttons descriptions accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Small platform specific bug fixes for problems found in randconfig builds.
* randconfig/mach:
ARM: ux500: don't select LEDS_GPIO for snowball
ARM: imx: build i.MX6 functions only when needed
ARM: imx: select CPU_FREQ_TABLE when needed
ARM: imx: fix ksz9021rn_phy_fixup
ARM: imx: build pm-imx5 code only when PM is enabled
ARM: omap: allow building omap44xx without SMP
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Using 'select' in Kconfig is hard, a platform cannot just
enable a driver without also making sure that its subsystem
is there. Also, there is no actual code dependency between
the platform and the gpio leds driver.
Without this patch, building without LEDS_CLASS esults in:
drivers/built-in.o: In function `create_gpio_led.part.2':
governor_userspace.c:(.devinit.text+0x5a58): undefined reference to `led_classdev_register'
drivers/built-in.o: In function `gpio_led_remove':
governor_userspace.c:(.devexit.text+0x6b8): undefined reference to `led_classdev_unregister'
This reverts 8733f53c6 "ARM: ux500: Kconfig: Compile in leds-gpio
support for Snowball" that introduced the regression and did not
provide a helpful explanation.
In order to leave the GPIO LED code still present in normal
builds, this also enables the symbol in u8500_defconfig, in addition
to the other LED drivers that are already selected there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
The head-v7.S contains a call to the generic cpu_suspend function,
which is only available when selected by the i.MX6 code. As
pointed out by Shawn Guo, i.MX5 does not actually use any
functions defined in head-v7.S. It is also needed only for
the i.MX6 power management code and for the SMP code, so
we can restrict building this file to situations in which
at least one of those two is present.
Finally, other platforms with a similar file call it headsmp.S,
so we can rename it to the same for consistency.
Without this patch, building imx5 standalone results in:
arch/arm/mach-imx/built-in.o: In function `v7_cpu_resume':
arch/arm/mach-imx/head-v7.S:104: undefined reference to `cpu_resume'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Eric Miao <eric.miao@linaro.org>
Cc: stable@vger.kernel.org
The i.MX cpufreq implementation uses the CPU_FREQ_TABLE helpers,
so it needs to select that code to be built. This problem has
apparently existed since the i.MX cpufreq code was first merged
in v2.6.37.
Building IMX without CPU_FREQ_TABLE results in:
arch/arm/plat-mxc/built-in.o: In function `mxc_cpufreq_exit':
arch/arm/plat-mxc/cpufreq.c:173: undefined reference to `cpufreq_frequency_table_put_attr'
arch/arm/plat-mxc/built-in.o: In function `mxc_set_target':
arch/arm/plat-mxc/cpufreq.c:84: undefined reference to `cpufreq_frequency_table_target'
arch/arm/plat-mxc/built-in.o: In function `mxc_verify_speed':
arch/arm/plat-mxc/cpufreq.c:65: undefined reference to `cpufreq_frequency_table_verify'
arch/arm/plat-mxc/built-in.o: In function `mxc_cpufreq_init':
arch/arm/plat-mxc/cpufreq.c:154: undefined reference to `cpufreq_frequency_table_cpuinfo'
arch/arm/plat-mxc/cpufreq.c:162: undefined reference to `cpufreq_frequency_table_get_attr'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Yong Shen <yong.shen@linaro.org>
Cc: stable@vger.kernel.org
The ksz9021rn_phy_fixup and mx6q_sabrelite functions try to
set up an ethernet phy if they can. They do check whether
phylib is enabled, but unfortunately the functions can only
be called from platform code if phylib is builtin, not
if it is a module
Without this patch, building with a modular phylib results in:
arch/arm/mach-imx/mach-imx6q.c: In function 'imx6q_sabrelite_init':
arch/arm/mach-imx/mach-imx6q.c:120:5: error: 'ksz9021rn_phy_fixup' undeclared (first use in this function)
arch/arm/mach-imx/mach-imx6q.c:120:5: note: each undeclared identifier is reported only once for each function it appears in
The bug was originally reported by Artem Bityutskiy but only
partially fixed in ef441806 "ARM: imx6q: register phy fixup only when
CONFIG_PHYLIB is enabled".
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
This moves the imx5 pm code out of the list of unconditionally
compiled files for imx5, mirroring what we already do for imx6
and how it was done before the code was move from mach-mx5 to
mach-imx in v3.3.
Without this patch, building with CONFIG_PM disabled results in:
arch/arm/mach-imx/pm-imx5.c:202:116: error: redefinition of 'imx51_pm_init'
arch/arm/mach-imx/include/mach-imx/common.h:154:91: note: previous definition of 'imx51_pm_init' was here
arch/arm/mach-imx/pm-imx5.c:209:116: error: redefinition of 'imx53_pm_init'
arch/arm/mach-imx/include/mach-imx/common.h:155:91: note: previous definition of 'imx53_pm_init' was here
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable@vger.kernel.org
The new omap4 cpuidle implementation currently requires
ARCH_NEEDS_CPU_IDLE_COUPLED, which only works on SMP.
This patch makes it possible to build a non-SMP kernel
for that platform. This is not normally desired for
end-users but can be useful for testing.
Without this patch, building rand-0y2jSKT results in:
drivers/cpuidle/coupled.c: In function 'cpuidle_coupled_poke':
drivers/cpuidle/coupled.c:317:3: error: implicit declaration of function '__smp_call_function_single' [-Werror=implicit-function-declaration]
It's not clear if this patch is the best solution for
the problem at hand. I have made sure that we can now
build the kernel in all configurations, but that does
not mean it will actually work on an OMAP44xx.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=/h+C
-----END PGP SIGNATURE-----
Merge tag 'ux500-fixes-v3.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes
From Linus Walleij <linus.walleij@linaro.org>:
Here are two audio fixes for the ux500 found by Lee Jones.
* tag 'ux500-fixes-v3.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: Ensure probing of Audio devices when Device Tree is enabled
ARM: ux500: Fix merge error, no matching driver name for 'snd_soc_u8500'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Kukjin Kim <kgene.kim@samsung.com>:
For HDMI, already HDMI support for EXYNOS in mainline kernel is broken
because its configuration moved to platform data but regarding platform
data didn't support yet. And others are for fix warnings.
* 'v3.6-samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Set HDMI platform data in Origen board
ARM: EXYNOS: Set HDMI platform data in SMDKV310
ARM: SAMSUNG: Add API to set platform data for s5p-tv driver
ARM: SAMSUNG: Set HDMI platform data for Exynos4x12 SoCs
ARM: Samsung: Make uart_save static in pm.c file
ARM: S3C24XX: Fix s3c2410_dma_enqueue parameters
ARM: S3C24XX: Add missing DMACH_DT_PROP
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'imx/fixes-for-3.6' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: dts: imx51-babbage: fix esdhc cd/wp properties
ARM: imx6: spin the cpu until hardware takes it down
ARM i.MX6q: Add virtual 1/3.5 dividers in the LDB clock path
Also updates to Linux 3.6-rc2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The binding doc and dts use properties "fsl,{cd,wp}-internal" while
esdhc driver uses "fsl,{cd,wp}-controller". Fix binding doc and dts
to get them match driver code.
Reported-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: <stable@vger.kernel.org>
Acked-by: Chris Ball <cjb@laptop.org>
Though commit 602bf40 (ARM: imx6: exit coherency when shutting down
a cpu) improves the stability of imx6q cpu hotplug a lot, there are
still hangs seen with a more stressful hotplug testing.
It's expected that once imx_enable_cpu(cpu, false) is called, the cpu
will be taken down by hardware immediately, and the code after that
will not get any chance to execute. However, this is not always the
case from the testing. The cpu could possibly be alive for a few
cycles before hardware actually takes it down. So rather than letting
cpu execute some code that could cause a hang in these cycles, let's
make the cpu spin there and wait for hardware to take it down.
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Remove the malformed "mem=" bootargs parameter in at91sam9g25ek.dts
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
AT91_ID_SYS as virq is incorrect because of spare irq support which
introduces NR_IRQS_LEGACY offset. It modifies rtc-at91sam9 driver in
order to get irq from resources.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
AT91_ID_SYS as virq is incorrect because of spare irq support which
introduces NR_IRQS_LEGACY offset.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Tested-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
sh73a0 :: intca_irq_pins_desc irq table had conflict
from irq 552 to irq 557 before.
But the second controller was simply trampling the
first one by way of the -EEXIST case from irq_alloc_desc_at().
But now, we have irqdomain support from
1d6a21b0a6
(sh: intc: initial irqdomain support)
The irqdomain code has simply tightened down the sanity checks and
error path. So, sh73a0 CPU board got some WARNING when booting now.
This patch fixup RELOC_BASE to solve this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Pull ARM fixes from Russell King:
"The largest thing in this set of changes is bringing back some of the
ARMv3 code to fix a compile problem noticed on RiscPC, which we still
support, even though we only support ARMv4 there.
(The reason is that the system bus doesn't support ARMv4 half-word
accesses, so we need the ARMv3 library code for this platform.)
The rest are all quite minor fixes."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7490/1: Drop duplicate select for GENERIC_IRQ_PROBE
ARM: Bring back ARMv3 IO and user access code
ARM: 7489/1: errata: fix workaround for erratum #720789 on UP systems
ARM: 7488/1: mm: use 5 bits for swapfile type encoding
ARM: 7487/1: mm: avoid setting nG bit for user mappings that aren't present
ARM: 7486/1: sched_clock: update epoch_cyc on resume
ARM: 7484/1: Don't enable GENERIC_LOCKBREAK with ticket spinlocks
ARM: 7483/1: vfp: only advertise VFPv4 in hwcaps if CONFIG_VFPv3 is enabled
ARM: 7482/1: topology: fix section mismatch warning for init_cpu_topology
Previous attempts to add platform probing of the Audio related devices
only call from non-DT initialisation functions. This patch extends that
functionality to the Device Tree related ones too.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The platform attempts to register platform device 'snd_soc_u8500'
which doesn't actually exist. Here we change the reference to the
correct one 'snd_soc_mop500'.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ldb_di[01]_podf is implemented as a clk-divider that
divides by 1 or 2. In reality, the ldb_di[01]_ipu_div
dividers divide by either 3.5 or 7. Adding a fixed factor
of 1/3.5 fixes their children's clock rates.
This should probably be converted to rate table based dividers,
once available.
Cc: <stable@vger.kernel.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
