PLL_SELFREQDCO bitfield is from bit 3 to 1, but the driver writes bits
from 4 to 1. The bit 4 is 'reserved', so this probably should not cause
any issues, but it's better to fix it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Preload register is dumped twice for video overlays and mflag register
is not dumped for GFX.
Fix the register dump.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
HDMI PLL's REGSD field is only set by the driver if the PLL's output
clock is over 1GHz. This is clearly an error, as REGSD should be set
always.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
PLLB input and output ranges were wrongly copied from at91sam9261 as the
datasheet didn't mention explicitly PLLB. Correct their values.
This fixes USB.
Reported-by: Andreas Henriksson <andreas.henriksson@endian.se>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: Andreas Henriksson <andreas.henriksson@endian.se>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
In the case of at91sam9g45_restart(), the driver is writing
AT91_DDRSDRC_LPCB_POWER_DOWN to AT91_DDRSDRC_RTR, this should actually be
AT91_DDRSDRC_LPR.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The PLL settings are committed by setting GO bit, which is then cleared
by the HW when the settings have been taken into use.
The current PLL code handles this wrong: instead of waiting for the bit
to be cleared, it waits for the bit to be set. Usually, the bit is
always set, as the CPU has just set it before. However, if the CPU takes
enough time between setting the GO bit and checking it, the HW may
already have cleared the bit and this leads to timeout error.
Fix the wait to check the bit properly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapfb disables all the overlays when freeing resources, but it should
also remove those overlays from overlay managers.
Not doing so causes a crash if omapfb is unbound and bound, or omapfb
module is removed and loaded, while keeping omapdss around.
Fix this by calling unset_manager() for all overlays.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When omapfb is shutting down, it will disable all the overlays. However,
instead of actually disabling all the overlays, it disables only all the
overlays that are currently attached to framebuffers.
On OMAP4+, this leaves the fourth overlay left enabled.
Fix the loop so that we actually go through all the overlays.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We should wait for any pending updates when an overlay manager is
about to be disabled, because the updates will never be finished if the
manager is disabled too early.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If we leave __exit annotation, driver can't be unbound
through sysfs.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdss drivers cannot handle devices being unbound while the devices
are part of a connected display pipeline. Module refcounts are used to
prevent unloading the modules, but one can still manually unbind the
devices via sysfs, causing crash.
Set suppress_bind_attrs to disable the bind/unbind support via sysfs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
without MODULE_ALIAS(), omapfb won't get loaded
automatically.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
While the hash function used by the revoke hashtable is good somewhere else,
it's not really good here.
The default hash shift (8) means that one third of the hashing function
gets lost (and is undefined anyways (8 - 12 = negative shift)):
"(block << (hash_shift - 12))) & (table->hash_size - 1)"
Instead, just use the kernel's generic hash function that gets used everywhere
else.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Due to a switched left and right side of an assignment,
dquot_writeback_dquots() never returned error. This could result in
errors during quota writeback to not be reported to userspace properly.
Fix it.
CC: stable@vger.kernel.org
Coverity-id: 1226884
Signed-off-by: Jan Kara <jack@suse.cz>
The check whether quota format is set even though there are no
quota files with journalled quota is pointless and it actually
makes it impossible to turn off journalled quotas (as there's
no way to unset journalled quota format). Just remove the check.
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Remove unnecessary mach/cpu.h header to be able to converge to a multiplatform
kernel.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Resolve shadow warnings that appear in W=2 builds by renaming
the "state" global to "vgastate".
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Since strsep is used to tokenize the options string, after each option
match the code should use "continue" to get the next token from strsep.
This patch applies this pattern consistently.
Previously, for "scrollback:" and "map:" the parse code would return
(unconditionally: strsep ensures *options != ','), causing any
following option to be ignored, while for "vc:" the parse code would
go on to parse further options within the same token, which could lead
to invalid input being accepted.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch wires up the new syscall sys_bpf() on powerpc.
Passes the tests in samples/bpf:
#0 add+sub+mul OK
#1 unreachable OK
#2 unreachable2 OK
#3 out of range jump OK
#4 out of range jump2 OK
#5 test1 ld_imm64 OK
#6 test2 ld_imm64 OK
#7 test3 ld_imm64 OK
#8 test4 ld_imm64 OK
#9 test5 ld_imm64 OK
#10 no bpf_exit OK
#11 loop (back-edge) OK
#12 loop2 (back-edge) OK
#13 conditional loop OK
#14 read uninitialized register OK
#15 read invalid register OK
#16 program doesn't init R0 before exit OK
#17 stack out of bounds OK
#18 invalid call insn1 OK
#19 invalid call insn2 OK
#20 invalid function call OK
#21 uninitialized stack1 OK
#22 uninitialized stack2 OK
#23 check valid spill/fill OK
#24 check corrupted spill/fill OK
#25 invalid src register in STX OK
#26 invalid dst register in STX OK
#27 invalid dst register in ST OK
#28 invalid src register in LDX OK
#29 invalid dst register in LDX OK
#30 junk insn OK
#31 junk insn2 OK
#32 junk insn3 OK
#33 junk insn4 OK
#34 junk insn5 OK
#35 misaligned read from stack OK
#36 invalid map_fd for function call OK
#37 don't check return value before access OK
#38 access memory with incorrect alignment OK
#39 sometimes access memory with incorrect alignment OK
#40 jump test 1 OK
#41 jump test 2 OK
#42 jump test 3 OK
#43 jump test 4 OK
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
[mpe: test using samples/bpf]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Change maintainer of nx-842 compression coprocessor driver
to Dan Streetman.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove the check of CONFIG_PPC_SUBPAGE_PROT when deciding if
is_hugepage_only_range() is extern or inline. The extern version is in
slice.c and is built if CONFIG_PPC_MM_SLICES=y.
There was no build break possible because CONFIG_PPC_SUBPAGE_PROT is
only selectable under conditions which also mean CONFIG_PPC_MM_SLICES
will be selected.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
arch/powerpc/mm/slice.c:704:5: error: expected identifier or ‘(’ before numeric constant
int is_hugepage_only_range(struct mm_struct *mm, unsigned long addr,
^
make[1]: *** [arch/powerpc/mm/slice.o] Error 1
make: *** [arch/powerpc/mm/slice.o] Error 2
This got introduced via 1217d34b53
"powerpc: Ensure global functions include their prototype". We
started including linux/hugetlb.h with that patch and now we have
#define is_hugepage_only_range(mm, addr, len) 0
with hugetlbfs disabled.
Fixes: 1217d34b53 ("powerpc: Ensure global functions include their prototype")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use netdev_alloc_pcpu_stats to allocate percpu stats and initialize syncp.
Fixes: 22e0f8b932 "net: sched: make bstats per cpu and estimator RCU safe"
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
while comparing for verifier state equivalency the comparison
was missing a check for uninitialized register.
Make sure it does so and add a testcase.
Fixes: f1bca824da ("bpf: add search pruning optimization to verifier")
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The synchronize_rcu() in netlink_release() introduces unacceptable
latency. Reintroduce minimal lookup so we can drop the
synchronize_rcu() until socket destruction has been RCUfied.
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Steinar H. Gunderson <sgunderson@bigfoot.com>
Reported-and-tested-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Limit primary to qemu vgamem size, to avoid reaching
qemu guest bug "requested primary larger than framebuffer"
on resizing screen too large to fit.
Remove unneeded and misleading variables.
Related to:
https://bugzilla.redhat.com/show_bug.cgi?id=1127552
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The problem is introduced by commit 764f612c6c3c231b(blk-merge:
don't compute bi_phys_segments from bi_vcnt for cloned bio),
and merge is needed if number of current segment isn't less than
max segments.
Strictly speaking, bio->bi_vcnt shouldn't be used here since
it may not be accurate in cases of both cloned bio or bio cloned
from, but bio_segments() is a bit expensive, and bi_vcnt is still
the biggest number, so the approach should work.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
as per 0c740d0afc (introduce for_each_thread() to replace the buggy
while_each_thread()) get rid of do_each_thread { } while_each_thread()
construct and replace it by a more error prone for_each_thread.
This patch doesn't introduce any user visible change.
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
PM freezer relies on having all tasks frozen by the time devices are
getting frozen so that no task will touch them while they are getting
frozen. But OOM killer is allowed to kill an already frozen task in
order to handle OOM situtation. In order to protect from late wake ups
OOM killer is disabled after all tasks are frozen. This, however, still
keeps a window open when a killed task didn't manage to die by the time
freeze_processes finishes.
Reduce the race window by checking all tasks after OOM killer has been
disabled. This is still not race free completely unfortunately because
oom_killer_disable cannot stop an already ongoing OOM killer so a task
might still wake up from the fridge and get killed without
freeze_processes noticing. Full synchronization of OOM and freezer is,
however, too heavy weight for this highly unlikely case.
Introduce and check oom_kills counter which gets incremented early when
the allocator enters __alloc_pages_may_oom path and only check all the
tasks if the counter changes during the freezing attempt. The counter
is updated so early to reduce the race window since allocator checked
oom_killer_disabled which is set by PM-freezing code. A false positive
will push the PM-freezer into a slow path but that is not a big deal.
Changes since v1
- push the re-check loop out of freeze_processes into
check_frozen_processes and invert the condition to make the code more
readable as per Rafael
Fixes: f660daac47 (oom: thaw threads if oom killed thread is frozen before deferring)
Cc: 3.2+ <stable@vger.kernel.org> # 3.2+
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
__thaw_task() no longer clears frozen flag since commit a3201227f8
(freezer: make freezing() test freeze conditions in effect instead of TIF_FREEZE).
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since f660daac47 (oom: thaw threads if oom killed thread is frozen
before deferring) OOM killer relies on being able to thaw a frozen task
to handle OOM situation but a3201227f8 (freezer: make freezing() test
freeze conditions in effect instead of TIF_FREEZE) has reorganized the
code and stopped clearing freeze flag in __thaw_task. This means that
the target task only wakes up and goes into the fridge again because the
freezing condition hasn't changed for it. This reintroduces the bug
fixed by f660daac47.
Fix the issue by checking for TIF_MEMDIE thread flag in
freezing_slow_path and exclude the task from freezing completely. If a
task was already frozen it would get woken by __thaw_task from OOM killer
and get out of freezer after rechecking freezing().
Changes since v1
- put TIF_MEMDIE check into freezing_slowpath rather than in __refrigerator
as per Oleg
- return __thaw_task into oom_scan_process_thread because
oom_kill_process will not wake task in the fridge because it is
sleeping uninterruptible
[mhocko@suse.cz: rewrote the changelog]
Fixes: a3201227f8 (freezer: make freezing() test freeze conditions in effect instead of TIF_FREEZE)
Cc: 3.3+ <stable@vger.kernel.org> # 3.3+
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most devices are configured for 32-bit DMA addresses.
Setting the mask to 32-bit here removes the need for the
drivers to do it separately.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull SCSI target updates from Nicholas Bellinger:
"Here are the target updates for v3.18-rc2 code. These where
originally destined for -rc1, but due to the combination of travel
last week for KVM Forum and my mistake of taking the three week merge
window literally, the pull request slipped.. Apologies for that.
Things where reasonably quiet this round. The highlights include:
- New userspace backend driver (target_core_user.ko) by Shaohua Li
and Andy Grover
- A number of cleanups in target, iscsi-taret and qla_target code
from Joern Engel
- Fix an OOPs related to queue full handling with CHECK_CONDITION
status from Quinn Tran
- Fix to disable TX completion interrupt coalescing in iser-target,
that was causing problems on some hardware
- Fix for PR APTPL metadata handling with demo-mode ACLs
I'm most excited about the new backend driver that uses UIO + shared
memory ring to dispatch I/O and control commands into user-space.
This was probably the most requested feature by users over the last
couple of years, and opens up a new area of development + porting of
existing user-space storage applications to LIO. Thanks to Shaohua +
Andy for making this happen.
Also another honorable mention, a new Xen PV SCSI driver was merged
via the xen/tip.git tree recently, which puts us now at 10 target
drivers in upstream! Thanks to David Vrabel + Juergen Gross for their
work to get this code merged"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (40 commits)
target/file: fix inclusive vfs_fsync_range() end
iser-target: Disable TX completion interrupt coalescing
target: Add force_pr_aptpl device attribute
target: Fix APTPL metadata handling for dynamic MappedLUNs
qla_target: don't delete changed nacls
target/user: Recalculate pad size inside is_ring_space_avail()
tcm_loop: Fixup tag handling
iser-target: Fix smatch warning
target/user: Fix up smatch warnings in tcmu_netlink_event
target: Add a user-passthrough backstore
target: Add documentation on the target userspace pass-through driver
uio: Export definition of struct uio_device
target: Remove unneeded check in sbc_parse_cdb
target: Fix queue full status NULL pointer for SCF_TRANSPORT_TASK_SENSE
qla_target: rearrange struct qla_tgt_prm
qla_target: improve qlt_unmap_sg()
qla_target: make some global functions static
qla_target: remove unused parameter
target: simplify core_tmr_abort_task
target: encapsulate smp_mb__after_atomic()
...
When quiet_error applies rate limiting to buffer_io_error calls, what the
they apply to is unclear because the name is so generic, particularly
if the messages are interleaved with others:
[ 1936.063572] quiet_error: 664293 callbacks suppressed
[ 1936.065297] Buffer I/O error on dev sdr, logical block 257429952, lost async page write
[ 1936.067814] Buffer I/O error on dev sdr, logical block 257429953, lost async page write
Also, the function uses printk_ratelimit(), although printk.h includes a
comment advising "Please don't use... Instead use printk_ratelimited()."
Change buffer_io_error to check the BH_Quiet bit itself, drop the
printk_ratelimit call, and print using printk_ratelimited.
This makes the messages look like:
[ 387.208839] buffer_io_error: 676394 callbacks suppressed
[ 387.210693] Buffer I/O error on dev sdr, logical block 211291776, lost async page write
[ 387.213432] Buffer I/O error on dev sdr, logical block 211291777, lost async page write
Signed-off-by: Robert Elliott <elliott@hp.com>
Reviewed-by: Webb Scales <webbnh@hp.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
buffer.c uses two printk calls to print these messages:
[67353.422338] Buffer I/O error on device sdr, logical block 212868488
[67353.422338] lost page write due to I/O error on sdr
In a busy system, they may be interleaved with other prints,
losing the context for the second message. Merge them into
one line with one printk call so the prints are atomic.
Also, differentiate between async page writes, sync page writes, and
async page reads.
Also, shorten "device" to "dev" to match the block layer prints:
[67353.467906] blk_update_request: critical target error, dev sdr, sector
1707107328
Also, use %llu rather than %Lu.
Resulting prints look like:
[ 1356.437006] blk_update_request: critical target error, dev sdr, sector 1719693992
[ 1361.383522] quiet_error: 659876 callbacks suppressed
[ 1361.385816] Buffer I/O error on dev sdr, logical block 256902912, lost async page write
[ 1361.385819] Buffer I/O error on dev sdr, logical block 256903644, lost async page write
Signed-off-by: Robert Elliott <elliott@hp.com>
Reviewed-by: Webb Scales <webbnh@hp.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Locking dependency detected below possible unsafe locking scenario:
CPU0 CPU1
T0: tipc_named_rcv() tipc_rcv()
T1: [grab nametble write lock]* [grab node lock]*
T2: tipc_update_nametbl() tipc_node_link_up()
T3: tipc_nodesub_subscribe() tipc_nametbl_publish()
T4: [grab node lock]* [grab nametble write lock]*
The opposite order of holding nametbl write lock and node lock on
above two different paths may result in a deadlock. If we move the
the updating of the name table after link state named out of node
lock, the reverse order of holding locks will be eliminated, and
as a result, the deadlock risk.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Govindarajulu Varadarajan says:
====================
enic: Bug fixes
This series fixes the following problem.
Please apply this to net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The following warning is shown when spinlock debug is enabled.
This occurs when enic_flow_may_expire timer function is running and
enic_stop is called on same CPU.
Fix this by using spink_lock_bh().
=================================
[ INFO: inconsistent lock state ]
3.17.0-netnext-05504-g59f35b8 #268 Not tainted
---------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
ifconfig/443 [HC0[0]:SC0[0]:HE1:SE1] takes:
(&(&enic->rfs_h.lock)->rlock){+.?...}, at:
enic_rfs_flw_tbl_free+0x34/0xd0 [enic]
{IN-SOFTIRQ-W} state was registered at:
[<ffffffff810a25af>] __lock_acquire+0x83f/0x21c0
[<ffffffff810a45f2>] lock_acquire+0xa2/0xd0
[<ffffffff814913fc>] _raw_spin_lock+0x3c/0x80
[<ffffffffa029c3d5>] enic_flow_may_expire+0x25/0x130[enic]
[<ffffffff810bcd07>] call_timer_fn+0x77/0x100
[<ffffffff810bd8e3>] run_timer_softirq+0x1e3/0x270
[<ffffffff8105f9ae>] __do_softirq+0x14e/0x280
[<ffffffff8105fdae>] irq_exit+0x8e/0xb0
[<ffffffff8103da0f>] smp_apic_timer_interrupt+0x3f/0x50
[<ffffffff81493742>] apic_timer_interrupt+0x72/0x80
[<ffffffff81018143>] default_idle+0x13/0x20
[<ffffffff81018a6a>] arch_cpu_idle+0xa/0x10
[<ffffffff81097676>] cpu_startup_entry+0x2c6/0x330
[<ffffffff8103b7ad>] start_secondary+0x21d/0x290
irq event stamp: 2997
hardirqs last enabled at (2997): [<ffffffff81491865>] _raw_spin_unlock_irqrestore+0x65/0x90
hardirqs last disabled at (2996): [<ffffffff814915e6>] _raw_spin_lock_irqsave+0x26/0x90
softirqs last enabled at (2968): [<ffffffff813b57a3>] dev_deactivate_many+0x213/0x260
softirqs last disabled at (2966): [<ffffffff813b5783>] dev_deactivate_many+0x1f3/0x260
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&enic->rfs_h.lock)->rlock);
<Interrupt>
lock(&(&enic->rfs_h.lock)->rlock);
*** DEADLOCK ***
Reported-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CPU1 is brought out of reset, it's MMU is not turned on yet, so it will
only be able to use physical addresses. For systems with that have the
MMU page configured for 0xC0000000, 0x80000000, or 0x40000000
"BIC 0x40000000" will work just fine, as it was just converting the
virtual address of &cpu1start_addr into a physical address, ie. 0xC0000000
became 0x80000000. So for systems where the SDRAM controller was able to do a
wrap-around access, this was working fine, as it was just dropping the MSB,
but for systems where out of bounds memory access is not allowed, this would
not allow CPU1 to correctly fetch &cpu1start_addr.
This patch fixes the secondary_trampoline code to correctly fetch the
physical address of cpu1start_addr directly. The patch will subtract the
correct PAGE_OFFSET from &cpu1start_addr. And since on this platform, the
physical memory will always start at 0x0, subtracting PAGE_OFFSET from
&cpu1start_addr will allow CPU1 to correctly fetch the value of cpu1start_addr.
While at it, change the name of cpu1start_addr to socfpga_cpu1start_addr
to avoid any future naming collisions for multiplatform image.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
---
v4: Updated commit log to correctly lay out the usage of PAGE_OFFSET and
add comments to the same effect.
v3: Used PAGE_OFFSET to get the physical address
v2: Correctly get the physical address instead of just a BIC hack.
Pull mailbox framework from Jassi Brar:
"A framework for Mailbox controllers and clients have been cooking for
more than a year now.
Everybody in the CC list had been copied on patchset revisions and
most of them have made sounds of approval, though just one concrete
Reviewed-by. The patchset has also been in linux-next for a couple of
weeks now and no conflict has been reported. The framework has the
backing of at least 5 platforms, though I can't say if/when they
upstream their drivers (some businesses have 'changed')"
(Further acked-by by Arnd Bergmann and Suman Anna in the pull request
thread)
* 'mailbox-for-linus' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
dt: mailbox: add generic bindings
doc: add documentation for mailbox framework
mailbox: Introduce framework for mailbox
mailbox: rename pl320-ipc specific mailbox.h
As PCM core handles the multiple linked streams in parallel, lockdep
gets confused (partly because of weak annotations) and spews the
false-positive warnings. This hasn't been a problem for long time but
the latest PCM lock path update seems to have woken up a sleeping
dog.
Here is an attempt to paper over this issue: pass the lock subclass
just calculated from the depth in snd_pcm_action_group(). Also, a
(possibly) wrong lock subclass set in snd_pcm_action_lock_mutex() is
dropped, too.
Reported-and-tested-by: Arthur Marsh <arthur.marsh@internode.on.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In file included from ./arch/arm64/include/asm/irq_work.h:4:0,
from include/linux/irq_work.h:46,
from include/linux/perf_event.h:49,
from include/linux/ftrace_event.h:9,
from include/trace/syscall.h:6,
from include/linux/syscalls.h:81,
from init/main.c:18:
./arch/arm64/include/asm/smp.h:24:3:
error: #error "<asm/smp.h> included in non-SMP build"
# error "<asm/smp.h> included in non-SMP build"
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Fixes: 3631073659 ("arm64: Tell irq work about self IPI support")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
GCC 4.9 complains if we take the difference of two pointers, and it's
printed with "%d". Fix this by using the proper flag - "t" for
ptrdiff_t.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The picvue_proc.c file creates the /proc interface for the PICVUE LCD
display driver. As a result of which, it needs to depend on the PROC_FS
symbol to avoid build problems like the following one when
CONFIG_PROC_FS is not enabled.
arch/mips/lasat/picvue_proc.c:26:14: error: 'pvc_linename'
defined but not used [-Werror=unused-variable]
static char *pvc_linename[PVC_NLINES] = {"line1", "line2"};
^
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8174/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
