[ Upstream commit 105f5528b9bbaa08b526d3405a5bcd2ff0c953c8 ]
In situations where an skb is paged, the transport header pointer and
tail pointer can be the same because the skb contents are in frags.
This results in ioctl(SIOCINQ/FIONREAD) incorrectly returning a
length of 0 when the length to receive is actually greater than zero.
skb->len is already correctly set in ip6_input_finish() with
pskb_pull(), so use skb->len as it always returns the correct result
for both linear and paged data.
Signed-off-by: Jamie Bainbridge <jbainbri@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 199ab00f3cdb6f154ea93fa76fd80192861a821d ]
Andrey reported a out-of-bound access in ip6_tnl_xmit(), this
is because we use an ipv4 dst in ip6_tnl_xmit() and cast an IPv4
neigh key as an IPv6 address:
neigh = dst_neigh_lookup(skb_dst(skb),
&ipv6_hdr(skb)->daddr);
if (!neigh)
goto tx_err_link_failure;
addr6 = (struct in6_addr *)&neigh->primary_key; // <=== HERE
addr_type = ipv6_addr_type(addr6);
if (addr_type == IPV6_ADDR_ANY)
addr6 = &ipv6_hdr(skb)->daddr;
memcpy(&fl6->daddr, addr6, sizeof(fl6->daddr));
Also the network header of the skb at this point should be still IPv4
for 4in6 tunnels, we shold not just use it as IPv6 header.
This patch fixes it by checking if skb->protocol is ETH_P_IPV6: if it
is, we are safe to do the nexthop lookup using skb_dst() and
ipv6_hdr(skb)->daddr; if not (aka IPv4), we have no clue about which
dest address we can pick here, we have to rely on callers to fill it
from tunnel config, so just fall to ip6_route_output() to make the
decision.
Fixes: ea3dc9601b ("ip6_tunnel: Add support for wildcard tunnel endpoints.")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 557c44be917c322860665be3d28376afa84aa936 ]
Andrey reported a fault in the IPv6 route code:
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN
Modules linked in:
CPU: 1 PID: 4035 Comm: a.out Not tainted 4.11.0-rc7+ #250
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
task: ffff880069809600 task.stack: ffff880062dc8000
RIP: 0010:ip6_rt_cache_alloc+0xa6/0x560 net/ipv6/route.c:975
RSP: 0018:ffff880062dced30 EFLAGS: 00010206
RAX: dffffc0000000000 RBX: ffff8800670561c0 RCX: 0000000000000006
RDX: 0000000000000003 RSI: ffff880062dcfb28 RDI: 0000000000000018
RBP: ffff880062dced68 R08: 0000000000000001 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
R13: ffff880062dcfb28 R14: dffffc0000000000 R15: 0000000000000000
FS: 00007feebe37e7c0(0000) GS:ffff88006cb00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000205a0fe4 CR3: 000000006b5c9000 CR4: 00000000000006e0
Call Trace:
ip6_pol_route+0x1512/0x1f20 net/ipv6/route.c:1128
ip6_pol_route_output+0x4c/0x60 net/ipv6/route.c:1212
...
Andrey's syzkaller program passes rtmsg.rtmsg_flags with the RTF_PCPU bit
set. Flags passed to the kernel are blindly copied to the allocated
rt6_info by ip6_route_info_create making a newly inserted route appear
as though it is a per-cpu route. ip6_rt_cache_alloc sees the flag set
and expects rt->dst.from to be set - which it is not since it is not
really a per-cpu copy. The subsequent call to __ip6_dst_alloc then
generates the fault.
Fix by checking for the flag and failing with EINVAL.
Fixes: d52d3997f8 ("ipv6: Create percpu rt6_info")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2ed1880fd61a998e3ce40254a99a2ad000f1a7d upstream.
The protocol field is checked when deleting IPv4 routes, but ignored for
IPv6, which causes problems with routing daemons accidentally deleting
externally set routes (observed by multiple bird6 users).
This can be verified using `ip -6 route del <prefix> proto something`.
Signed-off-by: Mantas Mikulėnas <grawity@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 45caeaa5ac0b4b11784ac6f932c0ad4c6b67cda0 ]
As Eric Dumazet pointed out this also needs to be fixed in IPv6.
v2: Contains the IPv6 tcp/Ipv6 dccp patches as well.
We have seen a few incidents lately where a dst_enty has been freed
with a dangling TCP socket reference (sk->sk_dst_cache) pointing to that
dst_entry. If the conditions/timings are right a crash then ensues when the
freed dst_entry is referenced later on. A Common crashing back trace is:
#8 [] page_fault at ffffffff8163e648
[exception RIP: __tcp_ack_snd_check+74]
.
.
#9 [] tcp_rcv_established at ffffffff81580b64
#10 [] tcp_v4_do_rcv at ffffffff8158b54a
#11 [] tcp_v4_rcv at ffffffff8158cd02
#12 [] ip_local_deliver_finish at ffffffff815668f4
#13 [] ip_local_deliver at ffffffff81566bd9
#14 [] ip_rcv_finish at ffffffff8156656d
#15 [] ip_rcv at ffffffff81566f06
#16 [] __netif_receive_skb_core at ffffffff8152b3a2
#17 [] __netif_receive_skb at ffffffff8152b608
#18 [] netif_receive_skb at ffffffff8152b690
#19 [] vmxnet3_rq_rx_complete at ffffffffa015eeaf [vmxnet3]
#20 [] vmxnet3_poll_rx_only at ffffffffa015f32a [vmxnet3]
#21 [] net_rx_action at ffffffff8152bac2
#22 [] __do_softirq at ffffffff81084b4f
#23 [] call_softirq at ffffffff8164845c
#24 [] do_softirq at ffffffff81016fc5
#25 [] irq_exit at ffffffff81084ee5
#26 [] do_IRQ at ffffffff81648ff8
Of course it may happen with other NIC drivers as well.
It's found the freed dst_entry here:
224 static bool tcp_in_quickack_mode(struct sock *sk)↩
225 {↩
226 ▹ const struct inet_connection_sock *icsk = inet_csk(sk);↩
227 ▹ const struct dst_entry *dst = __sk_dst_get(sk);↩
228 ↩
229 ▹ return (dst && dst_metric(dst, RTAX_QUICKACK)) ||↩
230 ▹ ▹ (icsk->icsk_ack.quick && !icsk->icsk_ack.pingpong);↩
231 }↩
But there are other backtraces attributed to the same freed dst_entry in
netfilter code as well.
All the vmcores showed 2 significant clues:
- Remote hosts behind the default gateway had always been redirected to a
different gateway. A rtable/dst_entry will be added for that host. Making
more dst_entrys with lower reference counts. Making this more probable.
- All vmcores showed a postitive LockDroppedIcmps value, e.g:
LockDroppedIcmps 267
A closer look at the tcp_v4_err() handler revealed that do_redirect() will run
regardless of whether user space has the socket locked. This can result in a
race condition where the same dst_entry cached in sk->sk_dst_entry can be
decremented twice for the same socket via:
do_redirect()->__sk_dst_check()-> dst_release().
Which leads to the dst_entry being prematurely freed with another socket
pointing to it via sk->sk_dst_cache and a subsequent crash.
To fix this skip do_redirect() if usespace has the socket locked. Instead let
the redirect take place later when user space does not have the socket
locked.
The dccp/IPv6 code is very similar in this respect, so fixing it there too.
As Eric Garver pointed out the following commit now invalidates routes. Which
can set the dst->obsolete flag so that ipv4_dst_check() returns null and
triggers the dst_release().
Fixes: ceb3320610 ("ipv4: Kill routes during PMTU/redirect updates.")
Cc: Eric Garver <egarver@redhat.com>
Cc: Hannes Sowa <hsowa@redhat.com>
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 79e49503efe53a8c51d8b695bedc8a346c5e4a87 ]
ip6_fragment, in case skb has a fraglist, checks if the
skb is cloned. If it is, it will move to the 'slow path' and allocates
new skbs for each fragment.
However, right before entering the slowpath loop, it updates the
nexthdr value of the last ipv6 extension header to NEXTHDR_FRAGMENT,
to account for the fragment header that will be inserted in the new
ipv6-fragment skbs.
In case original skb is cloned this munges nexthdr value of another
skb. Avoid this by doing the nexthdr update for each of the new fragment
skbs separately.
This was observed with tcpdump on a bridge device where netfilter ipv6
reassembly is active: tcpdump shows malformed fragment headers as
the l4 header (icmpv6, tcp, etc). is decoded as a fragment header.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reported-by: Andreas Karis <akaris@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 67e194007be08d071294456274dd53e0a04fdf90 ]
Commit 2759647247 ("ipv6: fix ECMP route replacement") introduced a
loop that removes all siblings of an ECMP route that is being
replaced. However, this loop doesn't stop when it has replaced
siblings, and keeps removing other routes with a higher metric.
We also end up triggering the WARN_ON after the loop, because after
this nsiblings < 0.
Instead, stop the loop when we have taken care of all routes with the
same metric as the route being replaced.
Reproducer:
===========
#!/bin/sh
ip netns add ns1
ip netns add ns2
ip -net ns1 link set lo up
for x in 0 1 2 ; do
ip link add veth$x netns ns2 type veth peer name eth$x netns ns1
ip -net ns1 link set eth$x up
ip -net ns2 link set veth$x up
done
ip -net ns1 -6 r a 2000::/64 nexthop via fe80::0 dev eth0 \
nexthop via fe80::1 dev eth1 nexthop via fe80::2 dev eth2
ip -net ns1 -6 r a 2000::/64 via fe80::42 dev eth0 metric 256
ip -net ns1 -6 r a 2000::/64 via fe80::43 dev eth0 metric 2048
echo "before replace, 3 routes"
ip -net ns1 -6 r | grep -v '^fe80\|^ff00'
echo
ip -net ns1 -6 r c 2000::/64 nexthop via fe80::4 dev eth0 \
nexthop via fe80::5 dev eth1 nexthop via fe80::6 dev eth2
echo "after replace, only 2 routes, metric 2048 is gone"
ip -net ns1 -6 r | grep -v '^fe80\|^ff00'
Fixes: 2759647247 ("ipv6: fix ECMP route replacement")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7dcdf941cdc96692ab99fd790c8cc68945514851 ]
Align vti6 with vti by returning GRE_KEY flag. This enables iproute2
to display tunnel keys on "ip -6 tunnel show"
Signed-off-by: David Forster <dforster@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ebf6c9cb23d7e56eec8575a88071dec97ad5c6e2 ]
Dmitry reported use-after-free in ip6_datagram_recv_specific_ctl()
A similar bug was fixed in commit 8ce48623f0cf ("ipv6: tcp: restore
IP6CB for pktoptions skbs"), but I missed another spot.
tcp_v6_syn_recv_sock() can indeed set np->pktoptions from ireq->pktopts
Fixes: 971f10eca1 ("tcp: better TCP_SKB_CB layout to reduce cache line misses")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7892032cfe67f4bde6fc2ee967e45a8fbaf33756 ]
Andrey Konovalov reported out of bound accesses in ip6gre_err()
If GRE flags contains GRE_KEY, the following expression
*(((__be32 *)p) + (grehlen / 4) - 1)
accesses data ~40 bytes after the expected point, since
grehlen includes the size of IPv6 headers.
Let's use a "struct gre_base_hdr *greh" pointer to make this
code more readable.
p[1] becomes greh->protocol.
grhlen is the GRE header length.
Fixes: c12b395a46 ("gre: Support GRE over IPv6")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 63117f09c768be05a0bf465911297dc76394f686 ]
Casting is a high precedence operation but "off" and "i" are in terms of
bytes so we need to have some parenthesis here.
Fixes: fbfa743a9d2a ("ipv6: fix ip6_tnl_parse_tlv_enc_lim()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fbfa743a9d2a0ffa24251764f10afc13eb21e739 ]
This function suffers from multiple issues.
First one is that pskb_may_pull() may reallocate skb->head,
so the 'raw' pointer needs either to be reloaded or not used at all.
Second issue is that NEXTHDR_DEST handling does not validate
that the options are present in skb->data, so we might read
garbage or access non existent memory.
With help from Willem de Bruijn.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 03e4deff4987f79c34112c5ba4eb195d4f9382b0 ]
Just like commit 4acd4945cd ("ipv6: addrconf: Avoid calling
netdevice notifiers with RCU read-side lock"), it is unnecessary
to make addrconf_disable_change() use RCU iteration over the
netdev list, since it already holds the RTNL lock, or we may meet
Illegal context switch in RCU read-side critical section.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ea7a80858f57d8878b1499ea0f1b8a635cc48de7 ]
Handle failure in lwtunnel_fill_encap adding attributes to skb.
Fixes: 571e722676 ("ipv4: support for fib route lwtunnel encap attributes")
Fixes: 19e42e4515 ("ipv6: support for fib route lwtunnel encap attributes")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 57ea52a865144aedbcd619ee0081155e658b6f7d ]
The GRO fast path caches the frag0 address. This address becomes
invalid if frag0 is modified by pskb_may_pull or its variants.
So whenever that happens we must disable the frag0 optimization.
This is usually done through the combination of gro_header_hard
and gro_header_slow, however, the IPv6 extension header path did
the pulling directly and would continue to use the GRO fast path
incorrectly.
This patch fixes it by disabling the fast path when we enter the
IPv6 extension header path.
Fixes: 78a478d0ef ("gro: Inline skb_gro_header and cache frag0 virtual address")
Reported-by: Slava Shwartsman <slavash@mellanox.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a55e23864d381c5a4ef110df94b00b2fe121a70d upstream.
When handling inbound packets, the two halves of the sequence number
stored on the skb are already in network order.
Fixes: 000ae7b269 ("esp6: Switch to new AEAD interface")
Signed-off-by: Tobias Brunner <tobias@strongswan.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4e479a96fc398ccf83bb1cffb4ffef8631beaf1 upstream.
When xfrm is applied to TSO/GSO packets, it follows this path:
xfrm_output() -> xfrm_output_gso() -> skb_gso_segment()
where skb_gso_segment() relies on skb->protocol to function properly.
This patch sets skb->protocol to ETH_P_IPV6 before dst_output() is called,
fixing a bug where GSO packets sent through an ipip6 tunnel are dropped
when xfrm is involved.
Signed-off-by: Eli Cooper <elicooper@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b5c2d49544e5930c96e2632a7eece3f4325a1888 ]
If an ip6 tunnel is configured to inherit the traffic class from
the inner header, the dst_cache must be disabled or it will foul
the policy routing.
The issue is apprently there since at leat Linux-2.6.12-rc2.
Reported-by: Liam McBirnie <liam.mcbirnie@boeing.com>
Cc: Liam McBirnie <liam.mcbirnie@boeing.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ac6e780070e30e4c35bd395acfe9191e6268bdd3 ]
With syzkaller help, Marco Grassi found a bug in TCP stack,
crashing in tcp_collapse()
Root cause is that sk_filter() can truncate the incoming skb,
but TCP stack was not really expecting this to happen.
It probably was expecting a simple DROP or ACCEPT behavior.
We first need to make sure no part of TCP header could be removed.
Then we need to adjust TCP_SKB_CB(skb)->end_seq
Many thanks to syzkaller team and Marco for giving us a reproducer.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Marco Grassi <marco.gra@gmail.com>
Reported-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 10df8e6152c6c400a563a673e9956320bfce1871 ]
First bug was added in commit ad6f939ab1 ("ip: Add offset parameter to
ip_cmsg_recv") : Tom missed that ipv4 udp messages could be received on
AF_INET6 socket. ip_cmsg_recv(msg, skb) should have been replaced by
ip_cmsg_recv_offset(msg, skb, sizeof(struct udphdr));
Then commit e6afc8ace6dd ("udp: remove headers from UDP packets before
queueing") forgot to adjust the offsets now UDP headers are pulled
before skb are put in receive queue.
Fixes: ad6f939ab1 ("ip: Add offset parameter to ip_cmsg_recv")
Fixes: e6afc8ace6dd ("udp: remove headers from UDP packets before queueing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sam Kumar <samanthakumar@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Tested-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fcd91dd449867c6bfe56a81cabba76b829fd05cd ]
Currently, GRO can do unlimited recursion through the gro_receive
handlers. This was fixed for tunneling protocols by limiting tunnel GRO
to one level with encap_mark, but both VLAN and TEB still have this
problem. Thus, the kernel is vulnerable to a stack overflow, if we
receive a packet composed entirely of VLAN headers.
This patch adds a recursion counter to the GRO layer to prevent stack
overflow. When a gro_receive function hits the recursion limit, GRO is
aborted for this skb and it is processed normally. This recursion
counter is put in the GRO CB, but could be turned into a percpu counter
if we run out of space in the CB.
Thanks to Vladimír Beneš <vbenes@redhat.com> for the initial bug report.
Fixes: CVE-2016-7039
Fixes: 9b174d88c2 ("net: Add Transparent Ethernet Bridging GRO support.")
Fixes: 66e5133f19 ("vlan: Add GRO support for non hardware accelerated vlan")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a220445f9f4382c36a53d8ef3e08165fa27f7e2c ]
The goal of the patch is to fix this scenario:
ip link add dummy1 type dummy
ip link set dummy1 up
ip link set lo down ; ip link set lo up
After that sequence, the local route to the link layer address of dummy1 is
not there anymore.
When the loopback is set down, all local routes are deleted by
addrconf_ifdown()/rt6_ifdown(). At this time, the rt6_info entry still
exists, because the corresponding idev has a reference on it. After the rcu
grace period, dst_rcu_free() is called, and thus ___dst_free(), which will
set obsolete to DST_OBSOLETE_DEAD.
In this case, init_loopback() is called before dst_rcu_free(), thus
obsolete is still sets to something <= 0. So, the function doesn't add the
route again. To avoid that race, let's check the rt6 refcnt instead.
Fixes: 25fb6ca4ed ("net IPv6 : Fix broken IPv6 routing table after loopback down-up")
Fixes: a881ae1f62 ("ipv6: don't call addrconf_dst_alloc again when enable lo")
Fixes: 33d99113b1 ("ipv6: reallocate addrconf router for ipv6 address when lo device up")
Reported-by: Francesco Santoro <francesco.santoro@6wind.com>
Reported-by: Samuel Gauthier <samuel.gauthier@6wind.com>
CC: Balakumaran Kannan <Balakumaran.Kannan@ap.sony.com>
CC: Maruthi Thotad <Maruthi.Thotad@ap.sony.com>
CC: Sabrina Dubroca <sd@queasysnail.net>
CC: Hannes Frederic Sowa <hannes@stressinduktion.org>
CC: Weilong Chen <chenweilong@huawei.com>
CC: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 68d00f332e0ba7f60f212be74ede290c9f873bc5 ]
The commit ea3dc9601b ("ip6_tunnel: Add support for wildcard tunnel
endpoints.") introduces support for wildcards in tunnels endpoints,
but in some rare circumstances ip6_tnl_lookup selects wrong tunnel
interface relying only on source or destination address of the packet
and not checking presence of wildcard in tunnels endpoints. Later in
ip6_tnl_rcv this packets can be dicarded because of difference in
ipproto even if fallback device have proper ipproto configuration.
This patch adds checks of wildcard endpoint in tunnel avoiding such
behavior
Fixes: ea3dc9601b ("ip6_tunnel: Add support for wildcard tunnel endpoints.")
Signed-off-by: Vadim Fedorenko <junk@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit db32e4e49ce2b0e5fcc17803d011a401c0a637f6 ]
Similar to commit 3be07244b7 ("ip6_gre: fix flowi6_proto value in
xmit path"), set flowi6_proto to IPPROTO_GRE for output route lookup.
Up until now, ip6gre_xmit_other() has set flowi6_proto to a bogus value.
This affected output route lookup for packets sent on an ip6gretap device
in cases where routing was dependent on the value of flowi6_proto.
Since the correct proto is already set in the tunnel flowi6 template via
commit 252f3f5a1189 ("ip6_gre: Set flowi6_proto as IPPROTO_GRE in xmit
path."), simply delete the line setting the incorrect flowi6_proto value.
Suggested-by: Jiri Benc <jbenc@redhat.com>
Fixes: c12b395a46 ("gre: Support GRE over IPv6")
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Lance Richardson <lrichard@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a09a4c8dd1ec7f830e1fb9e59eb72bddc965d168 upstream.
If a packet is either locally encapsulated or processed through GRO
it is marked with the offloads that it requires. However, when it is
decapsulated these tunnel offload indications are not removed. This
means that if we receive an encapsulated TCP packet, aggregate it with
GRO, decapsulate, and retransmit the resulting frame on a NIC that does
not support encapsulation, we won't be able to take advantage of hardware
offloads even though it is just a simple TCP packet at this point.
This fixes the problem by stripping off encapsulation offload indications
when packets are decapsulated.
The performance impacts of this bug are significant. In a test where a
Geneve encapsulated TCP stream is sent to a hypervisor, GRO'ed, decapsulated,
and bridged to a VM performance is improved by 60% (5Gbps->8Gbps) as a
result of avoiding unnecessary segmentation at the VM tap interface.
Reported-by: Ramu Ramamurthy <sramamur@linux.vnet.ibm.com>
Fixes: 68c33163 ("v4 GRE: Add TCP segmentation offload for GRE")
Signed-off-by: Jesse Gross <jesse@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
(backported from commit a09a4c8dd1ec7f830e1fb9e59eb72bddc965d168)
[adapt iptunnel_pull_header arguments, avoid 7f290c9]
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Juerg Haefliger <juerg.haefliger@hpe.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fac8e0f579695a3ecbc4d3cac369139d7f819971 upstream.
When drivers express support for TSO of encapsulated packets, they
only mean that they can do it for one layer of encapsulation.
Supporting additional levels would mean updating, at a minimum,
more IP length fields and they are unaware of this.
No encapsulation device expresses support for handling offloaded
encapsulated packets, so we won't generate these types of frames
in the transmit path. However, GRO doesn't have a check for
multiple levels of encapsulation and will attempt to build them.
UDP tunnel GRO actually does prevent this situation but it only
handles multiple UDP tunnels stacked on top of each other. This
generalizes that solution to prevent any kind of tunnel stacking
that would cause problems.
Fixes: bf5a755f ("net-gre-gro: Add GRE support to the GRO stack")
Signed-off-by: Jesse Gross <jesse@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Juerg Haefliger <juerg.haefliger@hpe.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 03c2778a938aaba0893f6d6cdc29511d91a79848 ]
Neither the failure or success paths of ping_v6_sendmsg release
the dst it acquires. This leads to a flood of warnings from
"net/core/dst.c:288 dst_release" on older kernels that
don't have 8bf4ada2e2 backported.
That patch optimistically hoped this had been fixed post 3.10, but
it seems at least one case wasn't, where I've seen this triggered
a lot from machines doing unprivileged icmp sockets.
Cc: Martin Lau <kafai@fb.com>
Signed-off-by: Dave Jones <davej@codemonkey.org.uk>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
commit 751eb6b6042a596b0080967c1a529a9fe98dac1d upstream.
In general, when DAD detected IPv6 duplicate address, ifp->state
will be set to INET6_IFADDR_STATE_ERRDAD and DAD is stopped by a
delayed work, the call tree should be like this:
ndisc_recv_ns
-> addrconf_dad_failure <- missing ifp put
-> addrconf_mod_dad_work
-> schedule addrconf_dad_work()
-> addrconf_dad_stop() <- missing ifp hold before call it
addrconf_dad_failure() called with ifp refcont holding but not put.
addrconf_dad_work() call addrconf_dad_stop() without extra holding
refcount. This will not cause any issue normally.
But the race between addrconf_dad_failure() and addrconf_dad_work()
may cause ifp refcount leak and netdevice can not be unregister,
dmesg show the following messages:
IPv6: eth0: IPv6 duplicate address fe80::XX:XXXX:XXXX:XX detected!
...
unregister_netdevice: waiting for eth0 to become free. Usage count = 1
Fixes: c15b1ccadb ("ipv6: move DAD and addrconf_verify processing
to workqueue")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 197c949e7798fbf28cfadc69d9ca0c2abbf93191 ]
Backport of this upstream commit into stable kernels :
89c22d8c3b ("net: Fix skb csum races when peeking")
exposed a bug in udp stack vs MSG_PEEK support, when user provides
a buffer smaller than skb payload.
In this case,
skb_copy_and_csum_datagram_iovec(skb, sizeof(struct udphdr),
msg->msg_iov);
returns -EFAULT.
This bug does not happen in upstream kernels since Al Viro did a great
job to replace this into :
skb_copy_and_csum_datagram_msg(skb, sizeof(struct udphdr), msg);
This variant is safe vs short buffers.
For the time being, instead reverting Herbert Xu patch and add back
skb->ip_summed invalid changes, simply store the result of
udp_lib_checksum_complete() so that we avoid computing the checksum a
second time, and avoid the problematic
skb_copy_and_csum_datagram_iovec() call.
This patch can be applied on recent kernels as it avoids a double
checksumming, then backported to stable kernels as a bug fix.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 903ce4abdf374e3365d93bcb3df56c62008835ba ]
It was first reported and reproduced by Petr (thanks!) in
https://bugzilla.kernel.org/show_bug.cgi?id=119581
free_percpu(rt->rt6i_pcpu) used to always happen in ip6_dst_destroy().
However, after fixing a deadlock bug in
commit 9c7370a166 ("ipv6: Fix a potential deadlock when creating pcpu rt"),
free_percpu() is not called before setting non_pcpu_rt->rt6i_pcpu to NULL.
It is worth to note that rt6i_pcpu is protected by table->tb6_lock.
kmemleak somehow did not report it. We nailed it down by
observing the pcpu entries in /proc/vmallocinfo (first suggested
by Hannes, thanks!).
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Fixes: 9c7370a166 ("ipv6: Fix a potential deadlock when creating pcpu rt")
Reported-by: Petr Novopashenniy <pety@rusnet.ru>
Tested-by: Petr Novopashenniy <pety@rusnet.ru>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Petr Novopashenniy <pety@rusnet.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 70a0dec45174c976c64b4c8c1d0898581f759948 ]
This fixes wrong-interface signaling on 32-bit platforms for entries
created when jiffies > 2^31 + MFC_ASSERT_THRESH.
Signed-off-by: Tom Goff <thomas.goff@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d5d8760b78d0cfafe292f965f599988138b06a70 ]
Since 32b8a8e59c ("sit: add IPv4 over IPv4 support")
ipip6_err() may be called for packets whose IP protocol is
IPPROTO_IPIP as well as those whose IP protocol is IPPROTO_IPV6.
In the case of IPPROTO_IPIP packets the correct protocol value is not
passed to ipv4_update_pmtu() or ipv4_redirect().
This patch resolves this problem by using the IP protocol of the packet
rather than a hard-coded value. This appears to be consistent
with the usage of the protocol of a packet by icmp_socket_deliver()
the caller of ipip6_err().
I was able to exercise the redirect case by using a setup where an ICMP
redirect was received for the destination of the encapsulated packet.
However, it appears that although incorrect the protocol field is not used
in this case and thus no problem manifests. On inspection it does not
appear that a problem will manifest in the fragmentation needed/update pmtu
case either.
In short I believe this is a cosmetic fix. None the less, the use of
IPPROTO_IPV6 seems wrong and confusing.
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d7591f0c41ce3e67600a982bab6989ef0f07b3ce upstream.
The three variants use same copy&pasted code, condense this into a
helper and use that.
Make sure info.name is 0-terminated.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09d9686047dbbe1cf4faa558d3ecc4aae2046054 upstream.
This looks like refactoring, but its also a bug fix.
Problem is that the compat path (32bit iptables, 64bit kernel) lacks a few
sanity tests that are done in the normal path.
For example, we do not check for underflows and the base chain policies.
While its possible to also add such checks to the compat path, its more
copy&pastry, for instance we cannot reuse check_underflow() helper as
e->target_offset differs in the compat case.
Other problem is that it makes auditing for validation errors harder; two
places need to be checked and kept in sync.
At a high level 32 bit compat works like this:
1- initial pass over blob:
validate match/entry offsets, bounds checking
lookup all matches and targets
do bookkeeping wrt. size delta of 32/64bit structures
assign match/target.u.kernel pointer (points at kernel
implementation, needed to access ->compatsize etc.)
2- allocate memory according to the total bookkeeping size to
contain the translated ruleset
3- second pass over original blob:
for each entry, copy the 32bit representation to the newly allocated
memory. This also does any special match translations (e.g.
adjust 32bit to 64bit longs, etc).
4- check if ruleset is free of loops (chase all jumps)
5-first pass over translated blob:
call the checkentry function of all matches and targets.
The alternative implemented by this patch is to drop steps 3&4 from the
compat process, the translation is changed into an intermediate step
rather than a full 1:1 translate_table replacement.
In the 2nd pass (step #3), change the 64bit ruleset back to a kernel
representation, i.e. put() the kernel pointer and restore ->u.user.name .
This gets us a 64bit ruleset that is in the format generated by a 64bit
iptables userspace -- we can then use translate_table() to get the
'native' sanity checks.
This has two drawbacks:
1. we re-validate all the match and target entry structure sizes even
though compat translation is supposed to never generate bogus offsets.
2. we put and then re-lookup each match and target.
THe upside is that we get all sanity tests and ruleset validations
provided by the normal path and can remove some duplicated compat code.
iptables-restore time of autogenerated ruleset with 300k chains of form
-A CHAIN0001 -m limit --limit 1/s -j CHAIN0002
-A CHAIN0002 -m limit --limit 1/s -j CHAIN0003
shows no noticeable differences in restore times:
old: 0m30.796s
new: 0m31.521s
64bit: 0m25.674s
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce683e5f9d045e5d67d1312a42b359cb2ab2a13c upstream.
We're currently asserting that targetoff + targetsize <= nextoff.
Extend it to also check that targetoff is >= sizeof(xt_entry).
Since this is generic code, add an argument pointing to the start of the
match/target, we can then derive the base structure size from the delta.
We also need the e->elems pointer in a followup change to validate matches.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc1221b3a163d1386d1052184202d5dc50d302d1 upstream.
32bit rulesets have different layout and alignment requirements, so once
more integrity checks get added to xt_check_entry_offsets it will reject
well-formed 32bit rulesets.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa412ba225dd3bc36d404c28cdc3d674850d80d0 upstream.
Once we add more sanity testing to xt_check_entry_offsets it
becomes relvant if we're expecting a 32bit 'config_compat' blob
or a normal one.
Since we already have a lot of similar-named functions (check_entry,
compat_check_entry, find_and_check_entry, etc.) and the current
incarnation is short just fold its contents into the callers.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d35812c3214afa5b37a675113555259cfd67b98 upstream.
Currently arp/ip and ip6tables each implement a short helper to check that
the target offset is large enough to hold one xt_entry_target struct and
that t->u.target_size fits within the current rule.
Unfortunately these checks are not sufficient.
To avoid adding new tests to all of ip/ip6/arptables move the current
checks into a helper, then extend this helper in followup patches.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 36472341017529e2b12573093cc0f68719300997 upstream.
When we see a jump also check that the offset gets us to beginning of
a rule (an ipt_entry).
The extra overhead is negible, even with absurd cases.
300k custom rules, 300k jumps to 'next' user chain:
[ plus one jump from INPUT to first userchain ]:
Before:
real 0m24.874s
user 0m7.532s
sys 0m16.076s
After:
real 0m27.464s
user 0m7.436s
sys 0m18.840s
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f24e230d257af1ad7476c6e81a8dc3127a74204e upstream.
Ben Hawkes says:
In the mark_source_chains function (net/ipv4/netfilter/ip_tables.c) it
is possible for a user-supplied ipt_entry structure to have a large
next_offset field. This field is not bounds checked prior to writing a
counter value at the supplied offset.
Base chains enforce absolute verdict.
User defined chains are supposed to end with an unconditional return,
xtables userspace adds them automatically.
But if such return is missing we will move to non-existent next rule.
Reported-by: Ben Hawkes <hawkes@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54d83fc74aa9ec72794373cb47432c5f7fb1a309 upstream.
Ben Hawkes says:
In the mark_source_chains function (net/ipv4/netfilter/ip_tables.c) it
is possible for a user-supplied ipt_entry structure to have a large
next_offset field. This field is not bounds checked prior to writing a
counter value at the supplied offset.
Problem is that mark_source_chains should not have been called --
the rule doesn't have a next entry, so its supposed to return
an absolute verdict of either ACCEPT or DROP.
However, the function conditional() doesn't work as the name implies.
It only checks that the rule is using wildcard address matching.
However, an unconditional rule must also not be using any matches
(no -m args).
The underflow validator only checked the addresses, therefore
passing the 'unconditional absolute verdict' test, while
mark_source_chains also tested for presence of matches, and thus
proceeeded to the next (not-existent) rule.
Unify this so that all the callers have same idea of 'unconditional rule'.
Reported-by: Ben Hawkes <hawkes@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e94e0cfb0887e4013b3b930fa6ab1fe6bb6ba91 upstream.
Otherwise this function may read data beyond the ruleset blob.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
