Commit graph

15164 commits

Author SHA1 Message Date
Luciano Coelho
648f6ed9f7 wlcore/wl18xx/wl12xx: use u8 instead of bool for host_fast_wakeup_support
The conf structure is going to be exported to a file, so we should use
only well defined types.  bool is not well defined and may vary from
platform to platform, so change the host_fast_wakeup_support type to
u8 instead.

Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08 09:14:08 +03:00
Luciano Coelho
9c6ead570c wlcore: export raw binary with the FW statistics in debugfs
Instead of parsing all the binary data returned by the firmware, we
should simply export the binary and let the userspace do the parsing.

This commit adds a new file to debugfs to do that.

Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08 09:14:08 +03:00
Luciano Coelho
f74ea74b82 wl18xx: add support to clear FW statistics
This patch calls ACX_CLEAR_STATISTICS to clear the firmware
statistics.  The trigger is a new debugfs file called
clear_fw_statistics in the fw_stats directory.

Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08 09:14:07 +03:00
Eyal Shapira
3e8d69352b wlcore: add debugfs control over rx interrupt pacing
Add control over several conf fields which combined
control the rx interrupt pacing mechanism, that is avoiding
getting an interrupt following a single frame rx but instead
have the FW trigger the interrupt only after a certain
amount of frames received or a timeout.

Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08 09:14:07 +03:00
Eyal Shapira
bc8e261233 wlcore: add support macros to easily add conf debugfs entries
The current debugfs code contains too much code duplication
of bolierplate code. Add some macro magic to avoid this and
enable adding new debugfs entries by using just a few lines.

Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08 09:14:07 +03:00
Grant Erickson
e16de2c4fc wl12xx: Add support for an external 26 MHz crystal source
Add support for an external 26 MHz crystal source.

[Changed wl->ref_clock to priv->ref_clock -- Luca.]

Signed-off-by: Grant Erickson <marathon96@gmail.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-07 18:14:41 +03:00
Ido Reis
9fccc82e19 wl18xx: pad only last frame in aggregration buffer for PG2
In PG2 only the last frame in the aggregate buffer should be
aligned to the sdio block size. This frame's header msb should be
set to 0, while in all the previous frames in the aggregation
buffer, this bit should be set to 1.

[Add a HW op for setting the frame ctrl bit only for 18xx. Other minor
cleanups - Arik]

[Make the pre_pkt_send operation optional -- Luca]

Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-07 18:11:06 +03:00
Ido Reis
f5755fe96c wl18xx: PG2.0 HW Watch dog interrupt support
In PG2, the HW watchdog interrupt occupies bit0 of the event vector, and
the SW watchdog is relocated to bit9. We perform the relocation
globally, as there's only one watchdog bit on previous platforms (bit0).

[Only mask in the new bit9 for platforms supporting it. This avoids
spurious events on other platforms - Arik]

Signed-off-by: Orit Brayer <orit@ti.com>
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-07 18:11:01 +03:00
Ido Reis
16ea473321 wl18xx: FW/PHY arguments added for PG2
PG2 requires 4 new parameters that to be passed to the PHY.

Use the actual PHY initialization struct size for the mem size of the
PHY_INIT section, to account for additions in params.

[Make sure PG1 still gets the original struct - Arik]

Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-07 18:10:57 +03:00
Ido Reis
73395a79df wl18xx: support PG2 version of the chip
PG2 has a unique chip id. It supports similar HW quirks.

Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-07 18:10:52 +03:00
Ido Reis
4085f641e7 wl18xx: fix PHY_INIT addresses mem size
was hardcoded 252, now uses the parameters struct size.

Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-07 18:10:48 +03:00
David S. Miller
c1864cfb80 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net 2012-06-06 15:06:41 -07:00
Johannes Berg
491b26b402 wireless: update wireless URLs
The preferred URL is http://wireless.kernel.org/
rather than http://linuxwireless.org/, update all
URLs to point there.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:32 -04:00
Sujith Manoharan
196fb860ce ath9k: Resync beacons properly
After a chip reset, the beacon timers have to re-programmed
correctly for a station in associated state. Use the PS flags
to ensure that this is done after a TSF sync happens, otherwise
the driver ends up using incorrect values for TBTT/DTIM in
powersave mode.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:32 -04:00
Sujith Manoharan
07c15a3ffd ath9k: Fix powersave locking
The 'ps_flags' is used/accessed in a variety of contexts
and requires proper locking. Use 'sc_pm_lock' appropriately.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:32 -04:00
Sujith Manoharan
b74713d04e ath9k: Handle fatal interrupts properly
When a fatal interrupt is received or it is detected that the baseband
has hung, the chip has to be reset immediately.  Otherwise, we end up
processing spurious interrupts. Ensure that we bail out properly in
the ISR when the reset work hasn't completed yet.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:31 -04:00
Sujith Manoharan
781b14a315 ath9k: Use atomic operations
The 'sc_flags' variable is being used in a number of places
with no locking whatsoever. This patch converts the usage
of sc_flags to atomic ops.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:31 -04:00
Sujith Manoharan
8da07830e1 ath9k: Move LNA code to antenna.c
And use a helper function to setup antennae after a reset.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:31 -04:00
Sujith Manoharan
af68abadac ath9k: Fix work handling
* Currently, there is no synchronization between the reset
  work and the tx-poll work. Fix this and make sure that we
  bail out properly if a reset work is in progress.

* Cleanup the PLL WAR and enable it for AR9340 too and
  use a helper for restarting work/timers after a reset.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:30 -04:00
Sujith Manoharan
ef1b6cd9a1 ath9k: Group link monitoring logic
Add link.c and move all the link/connection monitoring
code to it.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:30 -04:00
Rajkumar Manoharan
6995fb805e ath9k: improve BT FTP/PAN performance
When BT FTP/PAN transmits while WLAN is idle, the one of 9462 chain
often picks up BT's tx signal and starts receiving. If the current
weight is set to be higher than BT tx, BT tx will be aborted and this
also degrades BT performance. Hence lower WLAN rx priority in this
case only when there are no WLAN traffic.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:30 -04:00
Rajkumar Manoharan
153dccd467 ath9k_hw: fix power state for MCI
Program MCI related power registers only if MCI interrupts
are enabled. This could help to reduce power consumptions when
WLAN alone is enabled in BT coex chips.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:29 -04:00
Rajkumar Manoharan
c9ae6ab4c7 ath: do not update cycle counters with sleep mode
When the chip is waking up from sleep state, the cycle counters
might have incorrect readings. So it is better not to update those
readings with software counters.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:29 -04:00
Rajkumar Manoharan
0603143e47 ath9k: BT coex performance tuning for AR9462
Use smaller aggregation limit and increasing aggregation threshold
for osla that could improve wlan performance when there is HID profile.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:29 -04:00
Rajkumar Manoharan
99922a45e9 ath9k_hw: fix BT RF performance
When software rfkill is triggered, before put the chip in reset
state, give LNA and SPDT control to BT to make sure BT can have
good RF performance.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:28 -04:00
Rajkumar Manoharan
c8b6fbe1f1 ath9k_hw: configure ar9462 switching regulator
Enable WLAN and BT mode for switching regulator discontinuous
orverride for AR9462 chips.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:28 -04:00
Rajkumar Manoharan
9dc08eceb7 ath9k_hw: program BT to control SPDT
program BT to control SPDT everytime while loading switch table
from eeprom.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:28 -04:00
Rajkumar Manoharan
4fb7175bbd ath9k_hw: fix IQ calibration chain index
The chain index to perform IQ calibration is counted to number of valid
tx chains and then used for indexing chain specific registers. If the
chainmask is set to 0x2 (i.e chain 1 only), still it accesses chain 0
registers for chain 1. So use real chain index instead sequential one.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:28 -04:00
Rajkumar Manoharan
4f6bd1a8df ath9k: cleanup MCI indentation
Fix bad indentation & if nesting to lose about two levels
of unnecessary indentation.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:27 -04:00
Rajkumar Manoharan
5d294a1680 ath9k_hw: update ar9462 initval table to fix rx
The wrong ADC sample phase that happen between awake and
network/full sleep will lead to improper rx noisefloor
calibration.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:27 -04:00
Sujith Manoharan
e6930c4b32 ath9k: Use separate operational flags for BTCOEX
Also, use atomic operations to check the flags.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:26 -04:00
Sujith Manoharan
4cb54fa3a2 ath9k: Remove SC_OP_OFFCHANNEL
mac80211's IEEE80211_CONF_OFFCHANNEL can be used directly
to track offchannel state. Also pass the correct boolean
value to ath9k_hw_startpcureceive().

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:26 -04:00
Sujith Manoharan
2fd5d35bc8 ath9k_hw: Fix variable usage
Exposed by sparse:
ar9003_mci.c:1134:31: warning: Using plain integer as NULL pointer

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:26 -04:00
Sujith Manoharan
97ba515a20 ath9k: Add MCI interrupt to debugfs statistics
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:25 -04:00
Sujith Manoharan
31604cf0a7 ath9k_hw: Cleanup power mode API
The 'setChip' variable is unused, remove it and
simplify the functions.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:25 -04:00
Sujith Manoharan
5955b2b0ef ath9k_hw: Fix MCI usage
MCI has to be handled only when BTCOEX is actually enabled.
Check for this condition before calling MCI related functions
from various reset/calibration call-sites.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:25 -04:00
Sujith Manoharan
83c7a52dcc ath9k_hw: Fix AR_RTC_KEEP_AWAKE usage
The default value that is being programmed to AR_RTC_KEEP_AWAKE
is 0x2, there is no need to program it manually in various
functions.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:24 -04:00
Sujith Manoharan
e270e776a0 ath9k: Setup MCI interrupts properly
MCI interrupts have to be enabled only when BTCOEX is
actually in use.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:24 -04:00
Sujith Manoharan
d09f5f4cfb ath9k: Handle ASPM properly
ASPM has to be disabled when BTCOEX is in use, do this properly
by calling the bus-specific ASPM init routine after the
BTCOEX scheme has been determined.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:24 -04:00
Sujith Manoharan
aaa1ec46b3 ath9k: Prune ath9k_init_device
Instead of cluttering ath9k_init_device() with 'ath_softc'
specific initialization code, use ath9k_init_softc() to
setup driver-specific work routines, timers etc.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:23 -04:00
Chris Yungmann
2b0446c420 brcm80211: brcmsmac: fixed checkpatch and sparse warnings
Fixed checkpatch and sparse warnings related to aiutils.*

Signed-off-by: Chris Yungmann <yungmann.chris@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:23 -04:00
Vivek Natarajan
d202caff28 ath9k: Ensure a fair beacon distribution in IBSS mode
Configure CWmin based on slot time for IBSS mode. This helps
in increasing the beacon distribution of ath9k to accepted
levels in 11a mode.

Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:19:00 -04:00
Zero.Lin
cff3d1f093 rt2x00:Add RT5392 chipset support
Signed-off-by: Zero.Lin <Zero.Lin@mediatek.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:19:00 -04:00
Stanislaw Gruszka
d7fbcada37 iwl4965: claim RSN IBSS support
Similar like other drivers including iwl3945, do not configure group
keys to the hardware (on Ad-Hoc mode) to make IBSS RSN work.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:18:18 -04:00
Stanislaw Gruszka
6851dff3e6 rt2x00: claim RSN IBSS support
Similar like other drivers, do not configure group keys to the hardware
(on Ad-Hoc mode) to make IBSS RSN work.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:18:18 -04:00
Zefir Kurtisi
620a55687b ath9k: fix/add bits for spectral scanning
Updates for spectral scanning register modification for AR93x:
 * fix bits for spectral_scan_count
 * add bits for new parameters

Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:18:18 -04:00
Johannes Berg
e8c9bd5b8d cfg80211: clarify set_channel APIs
Now that we've removed all uses of the set_channel
API except for the monitor channel and in libertas,
clarify this. Split the libertas mesh use into a
new libertas_set_mesh_channel() operation, just to
keep backward compatibility, and rename the normal
set_channel() to set_monitor_channel().

Also describe the desired set_monitor_channel()
semantics more clearly.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:18:17 -04:00
John W. Linville
7c9c46c16d Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
Conflicts:
	drivers/net/wireless/iwlwifi/iwl-drv.c
2012-06-06 14:40:06 -04:00
Victor Goldenshtein
97511b15b1 wlcore: set channels 12-14 as pactive for sched scan
Introduce “pactive” scan mode – which instructs the fw to
perform a passive scan until an activity/energy is detected
on these channels, once energy detected the channel becomes
active.

Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-06 19:40:27 +03:00
Eliad Peller
587cc286c8 wlcore: compare ssid_len before comparing ssids
When comparing 2 ssids the ssid_len must be taken
into account. Otherwise, a substring will be treated
as equal.

This bug might cause ssids to get scanned as
public ssids (rather than hidden), resulting in
broadcast probe request (instead of ssid-specific
ones)

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-06 19:33:28 +03:00