gpio_direction_output() has a value argument, there's no need to call
gpio_set_value() explicitly right after.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 72f381ba05 (omap3: Remove VMMC2 regulator on IGEP v2)
removed an unused regulator entry, but left the second MMC channel
(used by the Libertas WLAN module) without link to power regulator.
This causes the SDIO module to fail being detected.
This patch adds the two regulators that actually feed the WLAN module
(1v8 from the TWL4030 VIO LDO, and a fixed 3v3). With that patch, the
second channel is properly detected. Details of the power supply
implementation were kindly provided by Enric Balletbo i Serra.
Also change vmmc1 to use symbolic names instead of direct device
reference.
Tested on an IGEPv2 Rev-B.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Patch "OMAP2xxx: hwmod: add I2C hwmods for OMAP2420, 2430"
in linux-next as of 20101203 introduced the following build
warning - fix this by removing the stray i2c_dev_attr.
arch/arm/mach-omap2/omap_hwmod_2430_data.c:483: warning: 'i2c_dev_attr' defined but not used
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
To support tvout on rx51,added Intilization data,
tvout as display device and enabled venc through gpio
on rx51
Signed-off-by: Srikar <ext-srikar.1.bhavanarayana@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Upcoming ASoC core and tlv320aic3x changes makes possible to take b part of
TLV320AIC34 into use on RX51/N900. Prepare to this by adding virtual supplies
and platform data for b part of the codec.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove second tlv320aic3x.h inclusion that came along the commit f0fba2a
"ASoC: multi-component - ASoC Multi-Component Support".
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is no MFD config option, MFD_SUPPORT should be selected instead.
This will prevent build errors when trying out different configurations.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
clk_get() return value should be checked with IS_ERR(). Furthermore,
clocks should be put and disabled properly.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert DMA library into DMA platform driver and make use of
platform data provided by hwmod data base for OMAP2+ onwards.
For OMAP1 processors, the DMA driver in mach-omap uses resource
structures for getting platform data.
Thanks to Tony Lindgren <tony@atomide.com> for fixing various
omap1 issues and testing the same on OSK5912 board.
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Prepare OMAP2+ DMA to use hwmod infrastructure so that DMA can register
as platform device.
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add OMAP4 DMA hwmod data. In addition to original dma hwmod data,
the following changes are added.
1. DMA device attributes structure is introduced for diffenrenciating
OMAP cpu's based on DMA features.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add OMAP2430 DMA hwmod data and also add required
DMA device attributes.
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add OMAP2420 DMA hwmod data and also add required
DMA device attributes.
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The convention for omap device naming is omap_XXX.
Rename the device and driver name in order to stick
to this naming convention.
Change device name in clock nodes as well.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Ben Dooks <ben-i2c@fluff.org>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
platform_cpu_die() is entered from the CPU's own idle thread, which
can not be migrated to other CPUs. Moreover, the 'cpu' argument
comes from the thread info, which will always be the 'current'
CPU. So remove this useless bug check.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We always need to wait for the dying CPU to reach a safe state before
taking it down, irrespective of the requirements of the platform.
Move the completion code into the ARM SMP hotplug code rather than
having each platform re-implement this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All platforms call trace_hardirqs_off() in their secondary startup code,
so move this into the core SMP code - it doesn't need to be in the
per-platform code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is a certain amount of smp_prepare_cpus() which doesn't belong
in the platform support code - that is, code which is invariant to the
SMP implementation. Move this code into arch/arm/kernel/smp.c, and
add a platform_ prefix to the original function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
scu_get_core_count() never returns zero cores, so we don't need to
check and correct if ncores is zero.
Tegra was missing the check against NR_CPUS, leading to a potential
bitfield overflow if this becomes the case.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure that the number of CPUs is sanity checked before setting
the number of possible CPUs. This avoids any chance of overflowing
the cpu_possible bitmap.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The AXI protocol specifies that the write response can only
be sent back to an AXI master when the last write data has been
accepted. This optimization enables the PL310 to send the write
response of certain write transactions as soon as the store buffer
accepts the write address. This behavior is not compatible with
the AXI protocol and is disabled by default. You enable this
optimization by setting the Early BRESP Enable bit in the
Auxiliary Control Register (bit [30]).
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Clearing bit 22 in the PL310 Auxiliary Control register (shared
attribute override enable) has the side effect of transforming Normal
Shared Non-cacheable reads into Cacheable no-allocate reads.
Coherent DMA buffers in Linux always have a Cacheable alias via the
kernel linear mapping and the processor can speculatively load cache
lines into the PL310 controller. With bit 22 cleared, Non-cacheable
reads would unexpectedly hit such cache lines leading to buffer
corruption
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enabling L2 prefetching improves performance as shown on Panda
ES2.1 board with mem test, and it has measurable impact on
performances. I think we should consider it, even though it damages
"writes" a bit. (rebased to k.org)
Usually the prefetch is used at both levels together L1 + L2, however,
to enable the CP15 prefetch engines, these are under security, and on
GP devices, we cannot enable it(e.g. on PandaBoard). However, just
enabling PL310 prefetch seems to provide performance improvement,
as shown in the data below (from Ubuntu) and would be a great thing
to pull in.
What prefetch does is enable automatic next line prefetching. With this
enabled, whenever the PL310 receives a cachable read request, it
automatically prefetches the following cache line as well.
Measurement Data:
==
STOCK 10.10 WITHOUT PATCH
========================
~# ./memspeed
size 8388608 8192k 8M
offset 8388608, 0
buffers 0x2aaad000 0x2b2ad000
copy libc 133 MB/s
copy Android v5 273 MB/s
copy Android NEON 235 MB/s
copy INT32 116 MB/s
copy ASM ARM 187 MB/s
copy ASM VLDM 64 204 MB/s
copy ASM VLDM 128 173 MB/s
copy ASM VLD1 216 MB/s
read ASM ARM 286 MB/s
read ASM VLDM 242 MB/s
read ASM VLD1 286 MB/s
write libc 1947 MB/s
write ASM ARM 1943 MB/s
write ASM VSTM 1942 MB/s
write ASM VST1 1935 MB/s
10.10 + PATCH
=============
~# ./memspeed
size 8388608 8192k 8M
offset 8388608, 0
buffers 0x2ab17000 0x2b317000
copy libc 129 MB/s
copy Android v5 256 MB/s
copy Android NEON 356 MB/s
copy INT32 127 MB/s
copy ASM ARM 321 MB/s
copy ASM VLDM 64 337 MB/s
copy ASM VLDM 128 321 MB/s
copy ASM VLD1 350 MB/s
read ASM ARM 496 MB/s
read ASM VLDM 470 MB/s
read ASM VLD1 488 MB/s
write libc 1701 MB/s
write ASM ARM 1682 MB/s
write ASM VSTM 1693 MB/s
write ASM VST1 1681 MB/s
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch removes the hardcoded value of auxctrl value and
construct it using bitfields
Bit 25 is reserved and is always set to 1. Same value
of this bit is retained in this patch
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
New assemblers need -march=armv7-a+sec on command line or
.arch_extension sec inline to enable use of the smc instruction.
This patch uses as-instr to check the latter to conditionally
enable the former in AFLAGS for files that use smc.
Checked on both old and new binutils to verify that it does
not break old versions.
Signed-off-by: John Rigby <john.rigby@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch will kill following section mismatch warnings:
WARNING: vmlinux.o(.text+0x24a00): Section mismatch in reference from the function zoom_twl_gpio_setup() to the (unknown reference) .init.data:(unknown)
The function zoom_twl_gpio_setup() references
the (unknown reference) __initdata (unknown).
This is often because zoom_twl_gpio_setup lacks a __initdata
annotation or the annotation of (unknown) is wrong.
WARNING: vmlinux.o(.text+0x24bfc): Section mismatch in reference from the function cm_t35_twl_gpio_setup() to the (unknown reference) .init.data:(unknown)
The function cm_t35_twl_gpio_setup() references
the (unknown reference) __initdata (unknown).
This is often because cm_t35_twl_gpio_setup lacks a __initdata
annotation or the annotation of (unknown) is wrong.
WARNING: vmlinux.o(.data+0x1d3e0): Section mismatch in reference from the variable h4_config to the (unknown reference) .init.data:(unknown)
The variable h4_config references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: vmlinux.o(.data+0x1dc08): Section mismatch in reference from the variable sdp2430_config to the (unknown reference) .init.data:(unknown)
The variable sdp2430_config references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: vmlinux.o(.data+0x1e1d8): Section mismatch in reference from the variable apollon_config to the (unknown reference) .init.data:(unknown)
The variable apollon_config references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Power to the wl12xx wlan device is controlled by a fixed regulator.
Boards that have the wl12xx should select REGULATOR_FIXED_VOLTAGE so
users will not be baffled.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add comments and IDs for the following erratas:
- i540: MPU cannot exit from Standby,
- i478: Unexpected Cold-Reset is generated when device is coming
back from OFF mode
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add minimal support for Nokia RM-680 board.
Tested with omap2plus_defconfig.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
[tony@atomide.com: updated to remove omap_gpio_init
Signed-off-by: Tony Lindgren <tony@atomide.com>
Introduce 97.6/195.2 MHz memory timing data. Based on patches by Eduardo
Valentin, Igor Dmitriev and Juha Keski-Saari.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: Eduardo Valentin <eduardo.valentin@nokia.com>
Cc: Igor Dmitriev <ext-dmitriev.igor@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Actually check for errors: print an error log and return NULL.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use an array to make it easier to add new values.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rename the current timings to indicate they're for 166 MHz. Based on
patches by Eduardo Valentin and Juha Keski-Saari.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a header file for Nokia SDRAM functions. Based on patches by Juha
Keski-Saari.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rename the file and functions so that it can be reused by future Nokia
boards. Based on patches by Juha Keski-Saari.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* usb-next: (132 commits)
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
usb: gadget: f_ncm.c added
usb: gadget: u_ether: prepare for NCM
usb: pch_udc: Fix setup transfers with data out
usb: pch_udc: Fix compile error, warnings and checkpatch warnings
usb: add ab8500 usb transceiver driver
USB: gadget: Implement runtime PM for MSM bus glue driver
USB: gadget: Implement runtime PM for ci13xxx gadget
USB: gadget: Add USB controller driver for MSM SoC
USB: gadget: Introduce ci13xxx_udc_driver struct
USB: gadget: Initialize ci13xxx gadget device's coherent DMA mask
USB: gadget: Fix "scheduling while atomic" bugs in ci13xxx_udc
USB: gadget: Separate out PCI bus code from ci13xxx_udc
...
It seems dsp-link will do this, and tidspbridge too at some point, but
right now it's not possible to select CONFIG_MPU_BRIDGE_IOMMU.
Cc: Fernando Guzman Lugo <fernando.lugo@ti.com>
Cc: Yogesh Marathe <yogesh_marathe@ti.com>
Signed-off-by: Felipe Contreras <felipe.contreras@nokia.com>
Some IOMMUs cannot use the whole 0x0 - 0xFFFFFFFF range.
With this new API the valid range can be set.
Signed-off-by: Fernando Guzman Lugo <x0095840@ti.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
We need to test for 24xx not 242x. Otherwise interrupts won't work.
Reported-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Provide a standard get_irqnr_preamble assembler macro for platforms
to use, which retrieves the base address of the GIC CPU interface
from gic_cpu_base_addr. Allow platforms to override this by defining
HAVE_GET_IRQNR_PREAMBLE.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Every architecture using the GIC has a gic_cpu_base_addr pointer for
GIC 0 for their entry assembly code to use to decode the cause of the
current interrupt. Move this into the common GIC code.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't need to re-pass the base address for the CPU interfaces to the
GIC for secondary CPUs, as it will never be different from the boot CPU
- and even if it was, we'd overwrite the boot CPU's base address.
Get rid of this argument, and rename to gic_secondary_init().
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide gic_init() which initializes the GIC distributor and current
CPU's GIC interface for the boot (or single) CPU.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
After Charu's GPIO hwmod patches, GPIO initialization on N800 emits
the following messages for all GPIO banks:
omap_hwmod: gpio1: cannot be enabled (3)
This is due to OMAP24XX_ST_GPIOS_SHIFT being defined as a bitmask.
Fix this and also fix two other macros that had the same problem.
Thanks to Tony Lindgren <tony@atomide.com> for originally reporting
this bug.
Signed-off-by: Paul Walmsley <paul@pwsan.com
Cc: Charulatha Varadarajan <charu@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise multi-omap1 support for omap1 won't work as the cpu_class_is_omap1()
won't work until the SoC is detected.
Note that eventually these will go away, please use ioremap + read/write instead.
Signed-off-by: Tony Lindgren <tony@atomide.com>
