This change updates the ux500 specific outer cache code to use
the new *_relaxed() I/O accessors.
Signed-off-by: Per Fransson <per.xx.fransson@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow the compiler to better optimize the page table walking code
by avoiding over-complex pmd_addr_end() calculations. These
calculations prevent the compiler spotting that we'll never iterate
over the PMD table, causing it to create double nested loops where
a single loop will do.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the options to enable the function graph tracer on ARM. Function
graph tracer support requires frame pointers, so exclude Thumb-2 and
also make sure FRAME_POINTER gets enabled when FUNCTION_GRAPH_TRACER is
used, since FUNCTION_TRACER doesn't "select FRAME_POINTER" when
ARM_UNWIND is used. Therefore, with GCC 4.4.0+, you get plain function
tracing without frame pointers, but you'll need them if you want
function graph tracing.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Cc: Tim Bird <tim.bird@am.sony.com>
[rabin@rab.in: rebase on top of latest code,
keep code in ftrace.c instead of separate file,
check for ftrace_graph_entry also]
Signed-off-by: Rabin Vincent <rabin@rab.in>
Use assembler macros to avoid copy/pasting code between the
implementations of the two variants of the mcount call.
Signed-off-by: Rabin Vincent <rabin@rab.in>
When FUNCTION_GRAPH_TRACER is enabled, place do_IRQ() and friends in the
IRQ_ENTRY section so that the irq-related features of the function graph
tracer work.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Multi-component commit f0fba2ad broke a few things which this patch should
fix. Tested on the DM355 EVM. I've been as careful as I can, but it would be
good if those with access to other Davinci boards could test.
--
The multi-component commit put the initialisation of
snd_soc_dai.[capture|playback]_dma_data into snd_soc_dai_ops.hw_params of the
McBSP, McASP & VCIF drivers (davinci-i2s.c, davinci-mcasp.c & davinci-vcif.c).
The initialisation had to be moved from the probe function in these drivers
because davinci_*_dai changed from snd_soc_dai to snd_soc_dai_driver.
Unfortunately, the DMA params pointer is needed by davinci_pcm_open (in
davinci-pcm.c) before hw_params is called. I have moved the initialisation to
a new snd_soc_dai_ops.startup function in each of these drivers. This fix
indicates that all platforms that use davinci-pcm must have been broken and
need to test with this fix.
--
The multi-component commit also changed the McBSP driver name from
"davinci-asp" to "davinci-i2s" in davinci-i2s.c without updating the board
level references to the driver name. This change is understandable, as there
is a similarly named "davinci-mcasp" driver in davinci-mcasp.c.
There is probably no 'correct' name for this driver. The DM6446 datasheet
calls it the "ASP" and describes it as a "specialised McBSP". The DM355
datasheet calls it the "ASP" and describes it as a "specialised ASP". The
DM365 datasheet calls it the "McBSP". Rather than fix this problem by
reverting to "davinci-asp", I've elected to avoid future confusion with the
"davinci-mcasp" driver by changing it to "davinci-mcbsp", which is also
consistent with the names of the functions in the driver. There are other
fixes required, so it was never going to be as simple as a revert anyway.
--
The DM365 only has one McBSP port (of the McBSP platforms, only the DM355 has
2 ports), so I've changed the the id of the platform_device from 0 to -1.
--
In davinci-evm.c, the DM6446 EVM can no longer share a snd_soc_dai_link
structure with the DM355 EVM as they use different cpu DAI names (the DM355
has 2 ports and the EVM uses the second port, but the DM6446 only has 1 port).
This also means that the 2 boards need different snd_soc_card structures.
--
The codec_name entries in davinci-evm.c didn't match the i2c ids in the board
files. I have only checked and fixed the details of the names used for the
McBSP based platforms. Someone with a McASP based platform (eg DA8xx) should
check the others.
Signed-off-by: Chris Paulson-Ellis <chris@edesix.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
arm: omap1: devices: need to return with a value
OMAP1: camera.h: add missing include
omap: dma: Add read-back to DMA interrupt handler to avoid spuriousinterrupts
OMAP2: Devkit8000: Fix mmc regulator failure
* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: intc: Fix up build failure introduced by radix tree changes.
MAINTAINERS: update the sh git tree entry.
sh: clkfwk: fix up compiler warnings.
sh: intc: Fix up initializers for gcc 4.5.
rtc: rtc-sh - fix a memory leak
* 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
ARM: mach-shmobile: ap4evb: add fsib 44100Hz rate
MAINTAINERS: update the ARM SH-Mobile git tree entry.
ARM: mach-shmobile: ap4evb: Mark NOR boot loader partitions read-only.
ARM: mach-shmobile: intc-sh7372: fix interrupt number
Now that clk_set_rate_ex() is gone, there is also no way to get at rate
setting algo id, which is now also completely unused. Kill it off before
new clock ops start using it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit 35bab0589b (ARM: imx: change the way
spi-imx devices are registered) contained a typo in mx25, leading to link time
failure.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Currently compilation breaks for the eukrea mbimx27 baseboard
when CONFIG_SPI_IMX is selected and CONFIG_TOUCHSCREEN_ADS7846
is not selected. Fix this by removing the ifdefs altogether.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Eric Benard <eric@eukrea.com>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: GIC: don't disable software generated interrupts
ARM: 6472/1: vexpress ct-ca9x4: only set twd_base if local timers are being used
ARM: arch/arm/kernel/traps.c: Convert sprintf_symbol to %pS
ARM: arch/arm/kernel/hw_breakpoint.c: Convert WARN_ON to WARN
ARM: 6462/1: EP93xx: Document DMA M2P API
ARM: 6470/1: atomic64: use generic implementation for OABI configurations
ARM: 6469/1: perf-events: squash compiler warning
ARM: 6468/1: backtrace: fix calculation of thread stack base
ARM: Fix DMA coherent allocator alignment
ARM: orion5x/kirkwood/mv78xx0: fix MPP configuration corner cases
[ARM] TS-78xxx NAND resource type should be IORESOURCE_MEM
ARM: pxa/saar: fix the building failure caused by typo
ARM: pxa/cm-x2xx: remove duplicate call to pxa27x_init_irq
ARM: pxa: fix the missing definition of IRQ_BOARD_END
ARM: mmp: fix cpuid detection on mmp2
[ARM] Kirkwood: restrict the scope of the PCIe reset workaround
[ARM] Kirkwood: fix timer initialization for LaCie boards
[ARM] Kirkwood: enhance TCLK detection
Software generated interrupts (SGI) are used for IPIs by the kernel.
While previous revisions of the GIC hardware were specified not to
implement enable bits for SGIs, more recent hardware is now permitted
to implement these bits in a per-CPU banked register.
The priority registers for the PPI and SGIs are also per-CPU banked
registers, so ensure that these are also appropriately initialized.
Reported-by: Scott Valentine <svalentine@concentris-systems.com>
Acked-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is a big revert of a lot of -rc1 tidspbridge patches in order to
get the driver back into a working state. It also includes a OMAP patch
that was approved by the OMAP maintainer.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Also, don't be picky about the location, which incidentally fixes the
build since MEMBLOCK_REAL_LIMIT is gone on 2.6.37.
arch/arm/plat-omap/devices.c: In function 'omap_dsp_reserve_sdram_memblock':
arch/arm/plat-omap/devices.c:287: error: 'MEMBLOCK_REAL_LIMIT'
undeclared (first use in this function)
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
In commit bde28b84, I made the assumption that CONFIG_SMP is always set
for the quad-core ct-ca9x4 platform. As it turns out, people who aren't
using the SMP goodness are confronted with a build failure.
This patch fixes this issue by ensure that twd_base is only set if
local timers are being used (and therefore SMP support is configured).
Reported-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Get rid of the following warning:
arch/arm/mach-omap1/devices.c: In function 'omap_init_wdt':
arch/arm/mach-omap1/devices.c:298: warning: 'return' with
no value, in function returning non-void
while at that, also change:
platform_device_register();
return 0;
into:
return platform_device_register();
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This makes the loader and bootenv partitions read-only under MTD for the
on-board NOR flash.
Signed-off-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add kernel-doc documentation for the EP93xx DMA memory to
peripheral/peripheral to memory API.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The old apcs-gnu ABI doesn't guarantee that double words are allocated
to registers with even alignment, causing the 64-bit exclusive memory
operations to be rejected by the assembler.
This patch requires that CONFIG_AEABI is set in order to use the native
atomic operations and falls back to the generic (spinlock) code otherwise.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
armv7_pmnc_counter_has_overflowed can return uninitialised data
if an invalid counter is specified.
This patch fixes the code to return 0 in this case, which squashes
the compiler warning from GCC 4.5.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When unwinding stack frames we must take care not to unwind
areas of memory that lie outside of the known extent of the stack.
This patch fixes an incorrect calculation of the stack base where
THREAD_SIZE is added to the stack pointer after it has already
been aligned to this value. Since the ALIGN macro performs this
addition internally, we end up overshooting the base by 8k.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
An out by one bug meant that the DMA coherent allocator was aligning
to one more bit than it should, causing it to run out of available
memory quicker. Fix this.
Reported-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
#include <media/omap1_camera.h> directive is required to
compile the dependant boards (board-ams-delta for now).
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Flush the writes to IRQSTATUS_L0 register in the DMA interrupt handler by reading the register
directly after write. This prevents the spurious DMA interrupts noted when using VDD_OPP 1
Signed-off-by: Mathias Nyman <mathias.nyman@nokia.com>
Acked-by: Santosh Shilimkar <Santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following error:
>regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby
>twl_reg twl_reg.6: can't register VMMC1, -22
>twl_reg: probe of twl_reg.6 failed with error -22
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Wrong MPP configuration would cause <cpu>_mpp_conf loop infinitely
because the mpp list iterator would not be incremented.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
The type was IORESOURCE_IO which is not what is expected by
plat_nand_probe(). This device has not worked since 2d098a72
("mtd: plat_nand: request memory resource before doing ioremap").
Signed-off-by: Michael Spang <mspang@csclub.uwaterloo.ca>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
As non-PFC chips are added that may support IRQs, pass through to the
generic helper. This follows the the SH change.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
