Currently, the OMAP3 HWMOD data defines two TIOCP_CFG register structures
(referred to as the SYSC register in the HWMOD data) where timers 1, 2 and 10
use one of the defintions and the other timers use the other definition. For
OMAP3 devices the structure of the DMTIMER TIOCP_CFG register is the same for
all 12 instances of the DMTIMER. Please note that this is a difference between
OMAP3 and OMAP4 and could be the source of the confusion.
For OMAP3 devices, the DMTIMER TIOCP_CFG register has the fields,
clock-activity, emufree, idlemode, enwakeup, softreset and autoidle for all
12 timers. Therefore, remove one of the SYSC register definitions for the
DMTIMERs and ensure the appropriate register fields are defined for all
DMTIMERs.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Errata Titles:
i103: Delay needed to read some GP timer, WD timer and sync timer
registers after wakeup (OMAP3/4)
i767: Delay needed to read some GP timer registers after wakeup (OMAP5)
Description (i103/i767):
If a General Purpose Timer (GPTimer) is in posted mode
(TSICR [2].POSTED=1), due to internal resynchronizations, values read in
TCRR, TCAR1 and TCAR2 registers right after the timer interface clock
(L4) goes from stopped to active may not return the expected values. The
most common event leading to this situation occurs upon wake up from
idle.
GPTimer non-posted synchronization mode is not impacted by this
limitation.
Workarounds:
1). Disable posted mode
2). Use static dependency between timer clock domain and MPUSS clock
domain
3). Use no-idle mode when the timer is active
Workarounds #2 and #3 are not pratical from a power standpoint and so
workaround #1 has been implemented. Disabling posted mode adds some CPU
overhead for configuring and reading the timers as the CPU has to wait
for accesses to be re-synchronised within the timer. However, disabling
posted mode guarantees correct operation.
Please note that it is safe to use posted mode for timers if the counter
(TCRR) and capture (TCARx) registers will never be read. An example of
this is the clock-event system timer. This is used by the kernel to
schedule events however, the timers counter is never read and capture
registers are not used. Given that the kernel configures this timer
often yet never reads the counter register it is safe to enable posted
mode in this case. Hence, for the timer used for kernel clock-events,
posted mode is enabled by overriding the errata for devices that are
impacted by this defect.
For drivers using the timers that do not read the counter or capture
registers and wish to use posted mode, can override the errata and
enable posted mode by making the following function calls.
__omap_dm_timer_override_errata(timer, OMAP_TIMER_ERRATA_I103_I767);
__omap_dm_timer_enable_posted(timer);
Both dmtimers and watchdogs are impacted by this defect this patch only
implements the workaround for the dmtimer. Currently the watchdog driver
does not read the counter register and so no workaround is necessary.
Posted mode will be disabled for all OMAP2+ devices (including AM33xx)
using a GP timer as a clock-source timer to guarantee correct operation.
This is not necessary for OMAP24xx devices but the default clock-source
timer for OMAP24xx devices is the 32k-sync timer and not the GP timer
and so should not have any impact. This should be re-visited for future
devices if this errata is fixed.
Confirmed with Vaibhav Hiremath that this bug also impacts AM33xx
devices.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
For OMAP2+ devices, when using DMTIMERs for system timers (clock-events and
clock-source) the posted mode configuration of the timers is used. To allow
the compiler to optimise the functions for configuring and reading the system
timers, the posted flag variable is hard-coded with the value 1. To make it
clear that posted mode is being used add some definitions so that it is more
readable.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
On OMAP4 boards using the TWL6030 PMIC, the sys_drm_msecure is
connected to the MSECURE input of the TWL6030 PMIC. This signal
controls the secure-mode operation of the PMIC. If its not mux'd
correctly, some functionality of the PMIC will not be accessible since
the PMIC will be in secure mode.
For example, if the TWL RTC is in secure mode, most of its registers
are read-only, meaning (re)programming the RTC (e.g. for wakeup from
suspend) will fail.
To fix, ensure the signal is properly mux'd as output when TWL is
intialized.
This fix is required when using recent versions of u-boot (>= v2012.04.01)
since u-boot is no longer setting the default mux for this pin.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove duplicated include.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This first patch serie start the cleanup of the header in mach
by moving all the platform data to include/linux/platform_data
and move the board header and drivers header next to them
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=c5hx
-----END PGP SIGNATURE-----
Merge tag 'for-3.8-at91_header_clean' of git://github.com/at91linux/linux-at91 into next/headers
From Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
arm: at91: mach header cleanup
This first patch serie start the cleanup of the header in mach
by moving all the platform data to include/linux/platform_data
and move the board header and drivers header next to them
* tag 'for-3.8-at91_header_clean' of git://github.com/at91linux/linux-at91:
arm: at91: move at91rm9200 rtc header in drivers/rtc
arm: at91: move reset controller header to arm/arm/mach-at91
arm: at91: move pit define to the driver
arm: at91: move at91_shdwc.h to arch/arm/mach-at91
arm: at91: move board header to arch/arm/mach-at91
arn: at91: move at91_tc.h to arch/arm/mach-at91
arm: at91 move at91_aic.h to arch/arm/mach-at91
arm: at91 move board.h to arch/arm/mach-at91
arm: at91: move platfarm_data to include/linux/platform_data/atmel.h
arm: at91: drop machine defconfig
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
introduced by the earlier clean-up and clean up few more
things for enabling multiplatform support.
The multiplatform kernel has been booted on omaps on
top of this branch with the work-in-progress patches
applied manually.
We cannot yet enable the multiplatform support though.
We still need the common clock framework patches, some
solution for dma-omap.h, and serial-omap.h moved before
we can enable it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQmaU8AAoJEBvUPslcq6VzbfcQAOEIQpv2zQz68euDDkCndBcG
rVjDIyAM/wgbxgdqK66FQvCZefQhSUBimBmjqagVwRh/2lIDZOfhIS98N5eMbJEQ
3UJUuOAPJQLmwR4zyKgbi/hdWZDEjnYvMJEmVSeSpXSmRO844ggtc9F2K22ouQ5m
CJ0WZE6p55v25bMLDETudLlzCfhrSGiApwV09IUxFAd9va7UeXibYt83oh1A6joo
U0i6sGbMgxR3uLi/7q7Wlm6dbCVU5N8+EtJ2L/tkoAQDHb+iLmkC8n3N3KPBkrEu
KpS7o3zuCDS3X6m8bD4w1j8WVeNX3ERA9avWMSBpfTQQcj0OvTPZixe7KC9WwT/4
nI0bAKQ/JWmFV+Ibo5jtVS151XeEG6ggap6aa+F3wYpkORY+jWcX0djW+1NDwScB
nGDcRI1n15jogoJJC9SB5wFW7K3wgi6Sb3Mo7nvNVvvQcHXpxiadujPP+tiHm7mn
mDoMJYHa0oI9jlWPSrAC5E8rfSR1NYRv7A5BLkakGXErEED+MByJ84PR3q4xDivx
B58HgsXTbJkQQug6o5yFK2vCKQW1Vsi0cdKrm3kY1JuLLfNMXbPFpAihxoLZ9Rp5
oDTdPpslgdEMMvg346q7XLFYiG9F5Zoz60MaUpYBa5EsmA16WB2ZT0t5bLIpxglx
0duNMqDZYsBrKc3aYjw3
=8Nz+
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/cleanup-headers-prepare-multiplatform-v3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/headers
From Tony Lindgren <tony@atomide.com>:
These changes deal with the issues of relative includes
introduced by the earlier clean-up and clean up few more
things for enabling multiplatform support.
The multiplatform kernel has been booted on omaps on
top of this branch with the work-in-progress patches
applied manually.
We cannot yet enable the multiplatform support though.
We still need the common clock framework patches, some
solution for dma-omap.h, and serial-omap.h moved before
we can enable it.
* tag 'omap-for-v3.8/cleanup-headers-prepare-multiplatform-v3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: Remove omap_init_consistent_dma_size()
ARM: OMAP: Remove NEED_MACH_GPIO_H
ARM: OMAP: Remove unnecessary mach and plat includes
ARM: OMAP2+: Fix relative includes for serial.h
ARM: OMAP: Fix relative includes for fpga.h
ARM: OMAP1: Remove relative includes
ARM: OMAP: Remove cpu_is_omap usage from plat-omap/dma.c
ARM: OMAP: Fix relative includes for debug-devices.h
ARM: OMAP: Remove plat-omap/common.h
ARM: OMAP: Move omap-pm-noop.c local to mach-omap2
ARM: OMAP: Fix relative includes for shared i2c.h file
ARM: OMAP: Make plat-omap/i2c.c port checks local
ARM: OMAP: Move omap2+ specific parts of sram.c to mach-omap2
ARM: OMAP: Move omap1 specific code to local sram.c
ARM: OMAP: Introduce common omap_map_sram() and omap_sram_reset()
ARM: OMAP: Split sram.h to local headers and minimal shared header
ARM: OMAP1: usb: fix sparse warnings
Conflicts:
arch/arm/mach-omap2/cm33xx.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes the following error:
CC arch/arm/mach-omap2/cm_common.o
arch/arm/mach-omap2/cm_common.c: In function ‘cm_register’:
arch/arm/mach-omap2/cm_common.c:42:11: error: ‘EINVAL’ undeclared (first use in this function)
arch/arm/mach-omap2/cm_common.c:42:11: note: each undeclared identifier is reported only once for each function it appears in
arch/arm/mach-omap2/cm_common.c:45:11: error: ‘EEXIST’ undeclared (first use in this function)
arch/arm/mach-omap2/cm_common.c: In function ‘cm_unregister’:
arch/arm/mach-omap2/cm_common.c:66:11: error: ‘EINVAL’ undeclared (first use in this function)
make[1]: *** [arch/arm/mach-omap2/cm_common.o] Error 1
make: *** [arch/arm/mach-omap2] Error 2
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Kevin Hilman and Paul Walmsley.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=pyxl
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.7-rc4/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren <tony@atomide.com>:
Minor OMAP PM and hwmod fixes for v3.7-rc series via
Kevin Hilman and Paul Walmsley.
* tag 'omap-for-v3.7-rc4/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4: PM: fix regulator name for VDD_MPU
ARM: OMAP4: hwmod data: do not enable or reset the McPDM during kernel init
ARM: OMAP2+: hwmod: add flag to prevent hwmod code from touching IP block during init
ARM: OMAP: hwmod: wait for sysreset complete after enabling hwmod
ARM: OMAP2+: clockdomain: Fix OMAP4 ISS clk domain to support only SWSUP
ARM: OMAP2+: PM: add missing newline to VC warning message
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Convert all OMAP4 specific platform files to use COMMON clk
and keep all the changes under the CONFIG_COMMON_CLK macro check
so it does not break any existing code. At a later point switch
to COMMON clk and get rid of all old/legacy code.
This converts all apis which will be called directly from COMMON
clk to take a struct clk_hw parameter, and all the internal platform
apis to take a struct clk_hw_omap parameter.
Changes are based off the original patch from Mike Turquette.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: created new omap2_clksel_find_parent_index() rather than
modifying omap2_init_clksel_parent(); moved clkhwops_iclk_wait to
clkt_iclk.c to fix OMAP4-only builds; added clk-provider.h include to clock.h
to try to fix some 3430-builds]
[mturquette@ti.com: squash patch for omap2_clkops_{en,dis}able_clkdm;
omap2_dflt_clk_is_enabled should not enable clocks]
Signed-off-by: Mike Turquette <mturquette@ti.com>
[paul@pwsan.com: fix compiler warning; update to apply; added kerneldoc on
non-trivial new functions; added the dpll3xxx clockdomain modifications]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
hwmod uses deferencing the clk pointer to acccess the clkdm.
With COMMON clk hwoever this will need to be deferenced through
the clk_hw_omap pointer, so do the necessary changes.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
plat/clock.c which has most of usecounting/locking infrastructure will
be used only for OMAP1 until that is moved to use COMMON clk.
reuse most of what plat/clock.h has while we move to common clk, and
move most of what 'struct clk' was as 'struct clk_hw_omap' which
will then be used to define platform specific parameters.
All usecounting/locking related variables from 'struct clk' are
dropped as they will not be used with 'struct clk_hw_omap'.
Based on the original changes from Mike Turquette.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Presently there are three peripherals that gets it timing
by runtime calculation. Those peripherals can work with
frequency scaling that affects gpmc clock. But timing
calculation for them are in different ways.
Here a generic runtime calculation method is proposed. Input
to this function were selected so that they represent timing
variables that are present in peripheral datasheets. Motive
behind this was to achieve DT bindings for the inputs as is.
Even though a few of the tusb6010 timings could not be made
directly related to timings normally found on peripherals,
expressions used were translated to those that could be
justified.
There are possibilities of improving the calculations, like
calculating timing for read & write operations in a more
similar way. Expressions derived here were tested for async
onenand on omap3evm (as vanilla Kernel does not have omap3evm
onenand support, local patch was used). Other peripherals,
tusb6010, smc91x calculations were validated by simulating
on omap3evm.
Regarding "we_on" for onenand async, it was found that even
for muxed address/data, it need not be greater than
"adv_wr_off", but rather could be derived from write setup
time for peripheral from start of access time, hence would
more be in line with peripheral timings. With this method
it was working fine. If it is required in some cases to
have "we_on" same as "wr_data_mux_bus" (i.e. greater than
"adv_wr_off"), another variable could be added to indicate
it. But such a requirement is not expected though.
It has been observed that "adv_rd_off" & "adv_wr_off" are
currently calculated by adding an offset over "oe_on" and
"we_on" respectively in the case of smc91x. But peripheral
datasheet does not specify so and so "adv_rd(wr)_off" has
been derived (to be specific, made ignorant of "oe_on" and
"we_on") observing datasheet rather than adding an offset.
Hence this generic routine is expected to work for smc91x
(91C96 RX51 board). This was verified on smsc911x (9220 on
OMAP3EVM) - a similar ethernet controller.
Timings are calculated in ps to prevent rounding errors and
converted to ns at final stage so that these values can be
directly fed to gpmc_cs_set_timings(). gpmc_cs_set_timings()
would be modified to take ps once all custom timing routines
are replaced by the generic routine, at the same time
generic timing routine would be modified to provide timings
in ps. struct gpmc_timings field types are upgraded from
u16 => u32 so that it can hold ps values.
Whole of this exercise is being done to achieve driver and
DT conversion. If timings could not be calculated in a
peripheral agnostic way, either gpmc driver would have to
be peripheral gnostic or a wrapper arrangement over gpmc
driver would be required.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Configure busturnaround, cycle2cycledelay, waitmonitoringtime,
clkactivationtime in gpmc_cs_set_timings(). This is done so
that boards can configure these parameters of gpmc in Kernel
instead of relying on bootloader. Also configure bool type
timings like extradelay.
This needed change to the existing users that were configuring
clk activation time and extra delay by directly writing to
registers. Thanks to Tony for making me aware of users of clk
activation and being kind enough to test the modified one.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Commit 7be2958 (ARM: PMU: Add runtime PM Support) updated the ARM PMU code to
use runtime PM which was prototyped and validated on the OMAP devices. In this
commit, there is no call pm_runtime_enable() and for OMAP devices
pm_runtime_enable() is currently being called from the OMAP PMU code when the
PMU device is created. However, there are two problems with this:
1. For any other ARM device wishing to use runtime PM for PMU they will need
to call pm_runtime_enable() for runtime PM to work.
2. When booting with device-tree and using device-tree to create the PMU
device, pm_runtime_enable() needs to be called from within the ARM PERF
driver as we are no longer calling any device specific code to create the
device. Hence, PMU does not work on OMAP devices that use the runtime PM
callbacks when using device-tree to create the PMU device.
Therefore, call pm_runtime_enable() directly from the ARM PMU driver when
registering the device. For platforms that do not use runtime PM,
pm_runtime_enable() does nothing and for platforms that do use runtime PM but
may not require it specifically for PMU, this will just add a little overhead
when initialising and uninitialising the PMU device.
Tested with PERF on OMAP2420, OMAP3430 and OMAP4460.
Acked-by: Kevin Hilman <khilman@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
arch/arm/mach-omap2/prcm.c and arch/arm/plat-omap/include/plat/prcm.h
are now completely unused and can be removed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
The hwmod code unconditionally calls _omap4_disable_module() on all
SoCs when a module doesn't enable correctly. This "worked" due to the
weak function omap4_cminst_wait_module_idle() in
arch/arm/mach-omap2/prcm.c, which was a no-op. But now those weak
functions are going away - they should not be used. So this patch
will now call the SoC-specific disable_module code, assuming it
exists.
Needs to be done before the weak function is removed, otherwise AM33xx
will crash early in boot.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Consolidate all of the copies of MAX_MODULE_HARDRESET_WAIT and
MAX_MODULE_SOFTRESET_WAIT into one place, arch/arm/mach-omap2/prm.h.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Split omap2_set_globals_prcm() into PRM, CM, and PRCM_MPU variants, since
these are all separate IP blocks. This should make it easier to move the
PRM, CM, PRCM_MPU code into drivers/ in future patchsets.
At this point arch/arm/plat-omap/include/plat/prcm.h is empty; a
subsequent patch will remove it, and remove the #include from all the
files that #include it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Now that all users of mach-omap2/omap2_cm_wait_idlest() have been removed,
delete the function and its supporting macros and prototypes.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Convert the OMAP clock code's _omap2_module_wait_ready() to use
SoC-independent CM functions that are provided by the CM code, rather
than using a deprecated function from mach-omap2/prcm.c.
This facilitates the future conversion of the CM code to a driver, and
also removes a mach-omap2/prcm.c user. mach-omap2/prcm.c will be removed
by a subsequent patch.
Some modules have IDLEST registers that aren't in the CM module, such
as the AM3517 IDLEST bits. So we also need a fallback function for
these non-CM odd cases. Create a temporary one in mach-omap2/clock.c,
intended to exist until the SCM drivers are ready.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Convert the OMAP2xxx APLL code to use omap2_cm_wait_module_ready(),
and move the low-level CM register manipulation functions to
mach-omap2/cm2xxx.c. The objectives here are to remove the dependency
on the deprecated omap2_cm_wait_idlest() function in
mach-omap2/prcm.c, so that code can be removed later; and move
low-level register accesses to the CM IP block to the CM code, which
will soon be moved into drivers/.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Modify the board files to use the SoC-specific system restart
functions. At this point it's possible to remove omap_prcm_restart()
from mach-omap2/prcm.c.
While removing the prototypes for the now-unused restart functions, clean
up a few more obsolete prototypes in mach-omap2/clock.h.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Split omap_prcm_restart() from mach-omap2/prcm.c into SoC-specific
variants. These functions need to be able to save the reboot reason
into the scratchpad RAM. This implies a dependency on both the PRM
and SCM IP blocks, so they've been moved into their own file. This
will eventually call functions in the PRM and SCM drivers, once those
are created.
Vaibhav Hiremath <hvaibhav@ti.com> identified an unused prototype in
the first version of this patch - now removed. Tony Lindgren
<tony@atomide.com> noted a compile problem with some RMK Kconfigs;
resolved in this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Collect all of the virt_prcm_set-specific clocktype code into
mach-omap2/clkt2xxx_virt_prcm_set.c. Remove its dependency on the
'sclk' and 'vclk' global variables. Those variables will be removed
by subsequent patches.
This is part of the process of cleaning up the OMAP2xxx clock code
and preparing for the removal of the omap_prcm_restart() function.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Remove the global 'dclk' variable, instead replacing it with a
variable local to the dpllcore clock type C file. This removes some
of the special-case code surrounding the OMAP2xxx clock init.
This patch is a prerequisite for the removal of the
omap_prcm_restart() code from arch/arm/mach-omap2/prcm.c. It also
cleans up some special-case OMAP2xxx clock code in the process.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Add SoC reset functions into the PRM code. These functions are based
on code from mach-omap2/prcm.c. They reset the SoC using the CORE DPLL
reset method (as opposed to one of the other two or three chip reset
methods).
Adding them here will facilitate their removal from
arch/arm/mach-omap2/prcm.c. (prcm.c is deprecated.)
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Get rid of the mach-omap2/common.c globals by moving the global
initialization for IP block addresses that must occur early into
mach-omap2/io.c. In the process, remove the *_map_common_io*() and
SoC-specific *set_globals* functions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
omap_prcm_get_reset_sources() is now unused; so, remove it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
gpmc_cs_set_timings() calculate ticks to be programmed by
rounding time in ns to next tick value. Hence remove
redundant rounding of nanosecond timing.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Setup the WIFI/BT GPIO pin muxes to enable WIFI/BT functionality.
This is needed to fix regression caused by recent versions of
u-boot that only mux essential pins.
Signed-off-by: Anders Hedlund <anders.j.hedlund@gmail.com>
Cc: Jonas Zetterberg <jozz@jozz.se>
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
Cc: Javier Martinez Canillas <martinez.javier@gmail.com>
Cc: Matthias Brugger <mbrugger@iseebcn.com>
[tony@atomide.com: updated comments to describe regression]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Call the non-DT omapdss setup code from board-generic if the board is
omap4-panda or omap4-sdp. This will give us working omapdss for those
boards when using DT kernel.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Device tree support for omapdss is still some way in the future. In an
effort to get a minimal DSS support for DT enabled kernel on selected
OMAP4 boards, we'll go for a temporary solution: We will call the same
non-DT omapdss setup code for OMAP4 SDP and Pandaboards from
board-generic.c, thus enabling DSS for those boards.
This patch moves the display setup code from board-4430sdp.c to
dss-common.c. dss-common.c will be called by the board-4430sdp.c when
running on non-DT kernel, and by board-generic.c when running on DT
enabled kernel.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Device tree support for omapdss is still some way in the future. In an
effort to get a minimal DSS support for DT enabled kernel on selected
OMAP4 boards, we'll go for a temporary solution: We will call the same
non-DT omapdss setup code for OMAP4 SDP and Pandaboards from
board-generic.c, thus enabling DSS for those boards.
This patch moves the display setup code from board-omap4panda.c to
dss-common.c. dss-common.c will be called by the board-omap4panda.c when
running on non-DT kernel, and by board-generic.c when running on DT
enabled kernel.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Platfrom device for ocp2scp is created using omap_device_build in
devices file. This is used for both omap4(musb) and omap5(dwc3).
This is needed to fix MUSB regression caused by commit c9e4412a
(arm: omap: phy: remove unused functions from omap-phy-internal.c)
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[tony@atomide.com: updated comments for regression info]
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order to reflect devices(usb_phy) attached to ocp2scp bus, ocp2scp
is assigned a device attribute to represent the attached devices.
This is needed to fix MUSB regression caused by commit c9e4412a
(arm: omap: phy: remove unused functions from omap-phy-internal.c)
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
[tony@atomide.com: updated comments for regression info]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The only thing omap_init_consistent_dma_size() does is increase the
consistent DMA size if CONFIG_FB_OMAP_CONSISTENT_DMA_SIZE is defined.
Increasing the consistent DMA size should no longer be needed with CMA
in place.
This patch removes omap_init_consistent_dma_size() and also
arch/arm/mach-omap2/io.c:omap_common_init_early() which becomes an empty
function.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[tony@atomide.com: updated for moved dma.h]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove the FIXME's in the suspend sequence since
we now intend to support system level RET support.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
commit 24d7b40a (ARM: OMAP2+: PM: MPU DVFS: use generic CPU device for
MPU-SS) updated the regulator name used for the MPU regulator, but only
updated OMAP3, not OMAP4. Fix the OMAP4 name as well, otherwise CPUfreq
fails to find the MPU regulator.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add OMAP4460 OPP definitions for voltage and frequencies based on
OMAP4460 ES1.0 DM Operating Condition Addendum Version 0.1
The following exceptions are present:
* Smartreflex support is still on experimental mode: the gains and min
limits are currently pending characterization data. Currently OMAP4430 values
are used.
* Efuse offset for core OPP100-OV setting is not clear in documentation.
* IVA OPPs beyond OPP100 are disabled due to the delta between max OMAP4460
current requirements and Phoenix Max supply on VCORE2 in the default
configuration - boards which have supply which can support this should
explicitly call opp_enable and enable the same.
* MPU OPPs > OPPTURBO can easily be detected using a efuse burnt - currently
disabled pending clock changes to support DCC feature.
[nm@ti.com: cleanups and updates from Datamanual]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
[t-kristo@ti.com: rebased to linux-3.6-rc5]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
