We currently have two symbols to control compilation the MFD subsystem,
MFD_SUPPORT and MFD_CORE. The MFD_SUPPORT is actually not required
at all, it only hides the submenu when not set, with the effect that
Kconfig warns about missing dependencies when another driver selects
an MFD driver while MFD_SUPPORT is disabled. Turning the MFD submenu
back from menuconfig into a plain menu simplifies the Kconfig syntax
for those kinds of users and avoids the surprise when the menu
suddenly appears because another driver was enabled that selects this
symbol.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
PPI handling is a bit of an odd beast. It uses its own low level
handling code and is hardwired to the local timers (hence lacking
a registration interface).
Instead, switch the low handling to the normal SPI handling code.
PPIs are handled by the handle_percpu_devid_irq flow.
This also allows the removal of some duplicated code.
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Brown <davidb@codeaurora.org>
Tested-by: David Brown <davidb@codeaurora.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Rather than clipping the number of CPUs using the compile-time NR_CPUS
constant, use the runtime nr_cpu_ids value instead. This allows the
nr_cpus command line option to work as expected.
Cc: <stable@kernel.org>
Reported-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't have cpu_is_omapxxxx SoC detection initialized until
SoC detection is initialized from init_early.
Note that with the common map_io we should no longer need
cpu_is_omapxxxx for ioremap.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise we can't do generic map_io as we currently rely on
static mappings that work only because of arch_ioremap.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This allows us to remove omap hacks for map_io.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This way we don't need to initialize SoC detection early
and can start using generic map_io.
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Boards used to specify zreladdr in their Makefile.boot with
zreladdr-y := x, so conflicting zreladdrs were silently overwritten.
This patch changes this to zreladdr-y += x, so that we end
up with multiple words in zreladdr in such a case. We can
detect this later and complain if necessary.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Based on the documents that I have here, there doesn't appear to be an
equivalent to erratum i443 for OMAP3630, so restrict this one to OMAP34xx
chips.
Also, explicitly restrict this erratum to EMU and HS devices.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The way that we detect which OMAP3 chips support I/O wakeup and
software I/O chain clock control is broken.
Currently, I/O wakeup is marked as present for all OMAP3 SoCs other
than the AM3505/3517. The TI81xx family of SoCs are at present
considered to be OMAP3 SoCs, but don't support I/O wakeup. To resolve
this, convert the existing blacklist approach to an explicit,
whitelist support, in which only SoCs which are known to support I/O
wakeup are listed. (At present, this only includes OMAP34xx,
OMAP3503, OMAP3515, OMAP3525, OMAP3530, and OMAP36xx.)
Also, the current code incorrectly detects the presence of a
software-controllable I/O chain clock on several chips that don't
support it. This results in writes to reserved bitfields, unnecessary
delays, and console messages on kernels running on those chips:
http://www.spinics.net/lists/linux-omap/msg58735.html
Convert this test to a feature test with a chip-by-chip whitelist.
Thanks to Dave Hylands <dhylands@gmail.com> for reporting this problem
and doing some testing to help isolate the cause. Thanks to Steve
Sakoman <sakoman@gmail.com> for catching a bug in the first version of
this patch. Thanks to Russell King <linux@arm.linux.org.uk> for
comments.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Dave Hylands <dhylands@gmail.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Tested-by: Steve Sakoman <sakoman@gmail.com>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The context lost count is modified in omap_sram_idle() path when
pwrdm_post_transition() is called. But pwrdm_post_transition() is called
only after omap_gpio_resume_after_idle() is called. Correct this so that
context lost count is modified before calling omap_gpio_resume_after_idle().
This would be useful when OMAP GPIO save/restore context is called by
the OMAP GPIO driver itself.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Removing modules iva, sr1_hwmod, sr2_hwmod, mailbox from
the base omap3xxx_hwmods list, so that they can be excluded
for am35x. This removes quite a few warnings on boot for AM35x.
Signed-off-by: Abhilash K V <abhilash.kv@ti.com>
[paul@pwsan.com: dropped 'mailbox class' comments; updated changelog]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Fix the shift and mask macros for DSIx_PPID fields in CONTROL_DSIPHY. The
OMAP4430 Public TRM vV has these fields mentioned correctly.
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP36xx and OMAP4xxx DPLLs have a different internal reference
clock frequency (fint) operating range than OMAP3430. Update the
dpll_test_fint() function to check for the correct frequency ranges
for OMAP36xx and OMAP4xxx.
For OMAP36xx and OMAP4xxx devices, DPLLs fint range is 0.5MHz to
2.5MHz for j-type DPLLs and otherwise it is 32KHz to 52MHz for all
other DPLLs.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The parent clock of the OCP_ABE_ICLK is the AESS_FCLK and the
parent clock of the AESS_FCLK is the ABE_FCLK...
ABE_FCLK --> AESS_FCLK --> OCP_ABE_ICLK
The AESS_FCLK and OCP_ABE_ICLK clocks both have dividers which
determine their operational frequency. However, the dividers for
the AESS_FCLK and OCP_ABE_ICLK are controlled via a single bit,
which is the CM1_ABE_AESS_CLKCTRL[24] bit. When this bit is set to
0, the AESS_FCLK divider is 1 and the OCP_ABE_ICLK divider is 2.
Similarly, when this bit is set to 1, the AESS_FCLK divider is 2
and the OCP_ABE_ICLK is 1.
The above relationship between the AESS_FCLK and OCP_ABE_ICLK
dividers ensure that the OCP_ABE_ICLK clock is always half the
frequency of the ABE_CLK...
OCP_ABE_ICLK = ABE_FCLK/2
The divider for the OCP_ABE_ICLK is currently missing so add a
divider that will ensure the OCP_ABE_ICLK frequency is always half
the ABE_FCLK frequency.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP4460 specific clocks are not getting added as the
cpu_is_omap44xx is choosing only OMAP4430 specific clock nodes.
Changing it to add to OMAP4460 specific clocks also.
This is clocks are required of temperature sensor.
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Cc: paul@pwsan.com
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This is a continuation of Mike Turquette's patch "OMAP3+: use
DPLL's round_rate when setting rate".
omap3_noncore_dpll_set_rate() and omap3_noncore_dpll_enable() call
omap2_get_dpll_rate() explicitly. It may be necessary for some
DPLLs to use a different function and so use the DPLLs recalc()
function pointer instead.
An example is the DPLL_ABE on OMAP4 which can have a 4X multiplier
in addition to the usual MN multipler and dividers and therefore
uses a different round_rate and recalc function.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Cc: Mike Turquette <mturquette@ti.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
[paul@pwsan.com: merged this patch with Mike's "use clock's recalc in DPLL
handling" patch; also reported by Misael]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The rounded rate can differ from target rate, so to better reflect
reality set clk->rate equal to the rounded rate when setting DPLL frequency.
This avoids issues where the DPLL frequency is slightly different than what
debugfs clock tree reports using the old target rate.
An example of a clock that requires this is DPLL_ABE on OMAP4 which
can have a 4x multiplier on top of the usual MN dividers depending on
register settings. This requires a special round_rate function that
might yield a rate different from the initial target.
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
omap3_noncore_dpll_set_rate uses omap2_dpll_round_rate explicitly. Instead
use the struct clk pointer's round_rate function to allow for DPLL's with
special needs.
An example of a clock that requires this is DPLL_ABE on OMAP4 which
can have a 4x multiplier on top of the usual MN dividers depending on
register settings. This requires a special round_rate function that
might yield a rate different from the initial target.
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: split rate assignment portion into a separate patch]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP4 DPLL_ABE can enable a 4X multipler on top of the normal MN multipler
and divider. This is achieved by setting CM_CLKMODE_DPLL_ABE.DPLL_REGM4XEN
bit in CKGEN module of CM1. From the OMAP4 TRM:
Fdpll = Fref x 2 x (4 x M/(N+1)) in case REGM4XEN bit field is set (only
applicable to DPLL_ABE).
Add new round_rate() and recalc() functions for OMAP4, that check the
setting of REGM4XEN bit and handle this appropriately. The new functions
are a simple wrapper on top of the existing omap2_dpll_round_rate() and
omap2_dpll_get_rate() functions to handle the REGM4XEN bit.
The REGM4XEN bit is only implemented for the ABE DPLL on OMAP4 and so
only dpll_abe_ck uses omap4_dpll_regm4xen_round_rate() and
omap4_dpll_regm4xen_recalc() functions.
Signed-off-by: Mike Turquette <mturquette@ti.com>
Tested-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: fixed attempt to return a negative from a fn returning
unsigned; pass along errors from omap2_dpll_round_rate();
added documentation; added Jon's S-o-b]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add nodes for devices used by PM code (mpu, dsp, iva).
Add a cpus node as well as recommended in the DT spec.
Remove mpu, dsp, iva devices init if is populated.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Kevin Hilman <khilman@ti.com>
Used the main OCP node to add bindings with the l3_noc driver.
Remove l3_noc static device creation if DT is populated.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Add device-tree support for the l3-noc driver.
Use platform_driver_register to defer the probing at device init
time.
Add documentation for the l3-noc bindings.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Still needed to boot until the i2c & twl driver is adapted to
device-tree. Otherwise the voltage control code will try to
access the twl and crash.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Re-cycle the original board-generic.c file to support Device Tree
for every OMAP2+ variants.
The current approach is an intermediate step before having only
one machine descriptor that will use some generic DT aware
functions.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Remove all these duplicated structures since a default one is now
available.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Since the device pointer is now retrieved using the hwmod name, remove
the static variables used to store the device pointers for DSP, MPU, IVA
and L3 devices for PM/DVFS usage.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Replace the struct device parameter of omap2_set_init_voltage
by the hwmod name. It will avoid having to store explicitely
the device pointer into a static variable.
Moreover, it will be a little bit more scalable if we introduce
new DVFS devices.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Replace the multiple omap2_get_XXX_device APIs with the new
omap_hwmod_name_get_dev that uses the hwmod name to get the proper
device.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Fixes bug where variable i was redundantly used for counting two nested loops.
Signed-off-by: Tapani Utriainen <tapani@technexion.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
`keypad_pads' is referred to by `keypad_data' which is
not __initdata, so `keypad_pads' should not be __initdata either.
Signed-off-by: Bjarne Steinsbo <bsteinsbo@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Support for the cpu_suspend functions is only built-in
when CONFIG_PM_SLEEP is enabled, but omap3/4, exynos4
and pxa always call cpu_suspend when CONFIG_PM is enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Current code calls omap4430_phy_init() twice in usb_musb_init().
Calling omap4430_phy_init() once is enough.
This patch removes the first omap4430_phy_init() call, which using an
uninitialized pointer as parameter.
This patch elimates below build warning:
arch/arm/mach-omap2/usb-musb.c: In function 'usb_musb_init':
arch/arm/mach-omap2/usb-musb.c:141: warning: 'dev' may be used uninitialized in this function
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Bjarne Steinsbo <bsteinsbo@gmail.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like 2600 kHz rate does not work reliably on 2430,
so just use the 100 kHz rate.
Otherwise the system often fails to boot properly with:
omap_i2c omap_i2c.2: timeout waiting for bus ready
omap_i2c omap_i2c.2: timeout waiting for bus ready
twl: i2c_write failed to transfer all messages
omap_i2c omap_i2c.2: timeout waiting for bus ready
twl: i2c_write failed to transfer all messages
omap_i2c omap_i2c.2: timeout waiting for bus ready
twl: i2c_write failed to transfer all messages
twl: clock init err [-110]
omap_i2c omap_i2c.2: timeout waiting for bus ready
twl: i2c_write failed to transfer all messages
TWL4030 Unable to unlock IDCODE registers --110
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove OMAP4_USBC1_ICUSB_PWRDNZ_MASK during enable/disable PWRDNZ mode for
MMC1_PBIAS and associated extended-drain MMC1 I/O cell. This is in accordance
with the control module programming guide. This fixes a bug where if trying to
use gpio_98 or gpio_99 and MMC1 at the same time the GPIO signal will be
affected by a changing SDMMC1_VDDS.
Software must keep MMC1_PBIAS cell and MMC1_IO cell PWRDNZ signals low whenever
SDMMC1_VDDS ramps up/down or changes for cell protection purposes.
MMC1 is based on SDMMC1_VDDS whereas USBC1 is based on SIM_VDDS therefore
they can operate independently.
Signed-off-by: Bryan Buckley <bryan.buckley@ti.com>
Acked-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Tested-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Port the old omapfb panel driver to DSS2. This patch changes the board
file only, the driver is ported in separate patch.
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Port the old omapfb panel driver to DSS2. This patch changes the board
file only, the driver is ported in separate patch.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Port the old omapfb panel driver to DSS2. This patch changes the board
file only, the driver is ported in separate patch.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stanley Miao <stanley.miao@windriver.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Port the old omapfb panel driver to DSS2. This patch changes the board
file only, the driver is ported in separate patch.
Cc: Hunyue Yau <hyau@mvista.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
board-omap3touchbook.c adds an LCD device, but the kernel doesn't
contain a driver for the device. So let's remove the unneeded LCD
device.
Cc: Gregoire Gentil <gregoire@gentil.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
RX51 uses the new DSS2 display driver, but the board file still
contained some code for the old omapfb driver. The old code can be
removed.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
