In case the interface is not used, power down the integrated GPHY during
suspend. Similarly to bcmgenet_open(), bcmgenet_resume() powers on the GPHY
prior to any UniMAC activity.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Power up the GPHY while we are bringing-up the network interface, and
conversely, upon bring down, power the GPHY down. In order to avoid
creating hardware hazards, make sure that the GPHY gets powered on
during bcmgenet_open() prior to the UniMAC being reset as the UniMAC may
start creating activity towards the GPHY if we reverse the steps.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the GPHY power down sequence by setting all power down bits, putting
the GPHY in reset, and finally cutting the 25Mhz reference clock.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were missing a number of extra steps and delays to power-up the GPHY, update
the sequence to reflect the proper procedure here.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for implementing the power down GPHY sequence, rename
bcmgenet_ephy_power_up to illustrate that it is not EPHY specific but
PHY agnostic, and add an "enable" argument.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CK25_DIS bit controls whether a 25Mhz clock is fed to the GPHY or
not, in preparation for powering down the integrated GPHY when relevant,
make sure we clear that bit.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If bcmgenet_power_down() fails, we would want to propagate a return
value from bcmgenet_wol_power_down_cfg() to know about this.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=m6GG
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.1-20150323' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2015-03-23
this is a pull request of 6 patches for net-next/master.
A patch by Florian Westphal, converts the skb->destructor to use
sock_efree() instead of own destructor. Ahmed S. Darwish's patch
converts the kvaser_usb driver to use unregister_candev(). A patch by
me removes a return from a void function in the m_can driver. Yegor
Yefremov contributes a patch for combined rx/tx LED trigger support. A
sparse warning in the esd_usb2 driver was fixes by Thomas Körper. Ben
Dooks converts the at91_can driver to use endian agnostic IO accessors.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter's static checker warned that in vxlan_stop we are checking
if 'vs' can be NULL while later we simply derreference it.
As after commit 56ef9c909b ("vxlan: Move socket initialization to
within rtnl scope") 'vs' just cannot be NULL in vxlan_stop() anymore, as
the interface won't go up if the socket initialization fails. So we are
good to just remove the check and make it consistent.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always use software checksumming, since the hardware does not have any
checksum offload support.
This significantly improves local TCP tx performance.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The start-of-frame and end-of-frame bits were accidentally swapped.
In the current code it does not make any difference, since they are
always used together.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change __raw accesors to endian agnostic versions to allow the driver
to work properly on big endian systems.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The hnd field of the structs does not need to be __le32: the
device just returns the value without using it itself.
Signed-off-by: Thomas Körper <thomas.koerper@esd.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add <ifname>-rxtx trigger, that will be activated both for tx
as rx events. This trigger mimics "activity" LED for Ethernet
devices.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use can-dev's unregister_candev() instead of directly calling
networking unregister_netdev(). While both are functionally
equivalent, unregister_candev() might do extra stuff in the
future than just calling networking layer unregistration code.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Return EPROBE_DEFER if Regulator returns EPROBE_DEFER
If the Flexcan driver is built into kernel and a regulator is used to
enable the CAN transceiver, the Flexcan driver may not use the regulator.
When initializing the Flexcan device with a regulator defined in the device
tree, but not initialized, the regulator subsystem returns EPROBE_DEFER, hence
the Flexcan init fails.
The solution for this is to return EPROBE_DEFER if regulator is not initialized
and wait until the regulator is initialized.
Signed-off-by: Andreas Werner <kernel@andy89.org>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Making sure that the bus-off state gets passed to can_change_state().
Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The PCAN USB (pro) FD adapters with firmware versions > 2.x support the
switching between ISO (default) and non-ISO conform bitstreams on the CAN bus.
The setting for the 2.x firmware adapters can be modified with the 'ip' tool
from the iproute2 package (option: fd-non-iso [on|off]).
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The PUCAN_CMD_RX_FRAME_(ENABLE|DISABLE) command has extended its purpose
and was therefore renamed to PUCAN_CMD_SET_(EN|DIS)_OPTION.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
smatch detected the following issue:
drivers/net/can/usb/gs_usb.c:904 gs_usb_probe() error:
potential null dereference 'dev'. (kzalloc returns null)
Add a check for null return from kzalloc and return -ENOMEM
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
USB endpoint's wMaxPacketSize field is an le16 entity. Use
appropriate le16_to_cpu macros to maintain endian independence.
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Current driver code arbitrarily assumes a max outstanding tx
value of 16 parallel transmissions. Meanwhile, the device
firmware provides its actual maximum inside its reply to the
CMD_GET_SOFTWARE_INFO message.
Under heavy tx traffic, if the interleaved transmissions count
increases above the limit reported by firmware, the firmware
breaks up badly, reports a massive list of internal errors, and
the candump traces hardly matches the actual frames sent and
received.
On the other hand, in certain models, the firmware can support
up to 48 tx URBs instead of just 16, increasing the driver
throughput by two-fold and reducing the possibility of -ENOBUFs.
Thus dynamically set the driver's max tx URBs value according
to firmware replies.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Transmission of an AP beacon does not call the TX interrupt service routine,
which usually does the cleanup. Instead, cleanup is handled in a tasklet
completion routine. Unfortunately, this routine has a serious bug in that it does
not release the DMA mapping before it frees the skb, thus one IOMMU mapping is
leaked for each beacon. The test system failed with no free IOMMU mapping slots
approximately one hour after hostapd was used to start an AP.
This issue was reported and tested at https://github.com/lwfinger/rtlwifi_new/issues/30.
Reported-and-tested-by: Kevin Mullican <kevin@mullican.com>
Cc: Kevin Mullican <kevin@mullican.com>
Signed-off-by: Shao Fu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.18+]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the device is powered up, some (older) firmware versions fail to work
properly if we send commands before the boot is complete (everything is OK
when the device is hot-plugged). The firmware indicates its ready status by
putting the link up.
Newer firmwares delay the first command so they don't suffer from this problem.
They also report the link being always up.
Wait for firmware to become ready (link up) before sending any commands and/or
data.
This also allows lowering CMD_TIMEOUT value to a reasonable time.
Tested with 4.1.0.9 (old) and 4.1.0.30 (new) firmware versions.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
AIC needs to be registered only when BTCOEX is enabled.
This fixes the error reported by kbuild:
>> ERROR: "ar9003_hw_attach_aic_ops" [drivers/net/wireless/ath/ath9k/ath9k_hw.ko] undefined!
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The BCM43362 firmware falsely reports it is capable of providing
MBSS. As a result AP mode no longer works for this device. Therefor
disable MBSS in the driver for this chipset.
Cc: stable@vger.kernel.org # 3.19.y
Reported-by: Jorg Krause <jkrause@posteo.de>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
NetCP 1.5 available on newer K2 SoCs such as K2E and K2L introduced 3
variants of the ethss subsystem, 9 port, 5 port and 2 port. These have
one host port towards the CPU and N external slave ports.
To customize the driver for these new ethss sub systems, multiple
compatibility strings are introduced. Currently some of parameters that
are different on different variants such as number of ALE ports, stats
modules and number of ports are defined through constants. These are now
changed to variables in gbe_priv data that get set based on the
compatibility string. This is required as there are no hardware
identification registers available to distinguish among the variants
of NetCP 1.5 ethss. However there is identification register available
to differentiate between NetCP 1.4 vs NetCP 1.5 and the same is made use
of in the code to differentiate them.
For more reading on the details of this peripheral, please refer to the
User Guide available at http://www.ti.com/lit/pdf/spruhz3
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Mugunthan V N <mugunthanvnm@ti.com>
CC: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: Christoph Jaeger <cj@linux.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Markus Pargmann <mpa@pengutronix.de>
CC: Kumar Gala <galak@codeaurora.org>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Rob Herring <robh+dt@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following checkpatch error. It seems to have passed checkpatch
last time when original code was introduced.
ERROR: Macros with complex values should be enclosed in parentheses
#172: FILE: drivers/net/ethernet/ti/netcp_ethss.c:869:
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Mugunthan V N <mugunthanvnm@ti.com>
CC: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: Christoph Jaeger <cj@linux.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Markus Pargmann <mpa@pengutronix.de>
CC: Kumar Gala <galak@codeaurora.org>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Rob Herring <robh+dt@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keystone netcp driver re-uses davinci mdio driver. So enable it
by default for keystone netcp driver.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Mugunthan V N <mugunthanvnm@ti.com>
CC: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: Christoph Jaeger <cj@linux.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Markus Pargmann <mpa@pengutronix.de>
CC: Kumar Gala <galak@codeaurora.org>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Rob Herring <robh+dt@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethss has multiple modules within the sub system
- switch sub system
- sgmii
- mdio
- switch module
NetCP driver re-uses existing davinci mdio driver. It requires to
have its own register region to map the reg space. So restructure
the code to use separate reg region for the individual modules it
manages. Use range property to define register space of NetCP and
use reg property to define individual reg spaces. So MDIO will have
its own reg space to map. This is a pre-requisite to enable MDIO
driver for NetCP.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Mugunthan V N <mugunthanvnm@ti.com>
CC: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: Christoph Jaeger <cj@linux.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Markus Pargmann <mpa@pengutronix.de>
CC: Kumar Gala <galak@codeaurora.org>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Rob Herring <robh+dt@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
10G switch requires forward port number in the taginfo field,
where as it should be in packet_info field for necp 1.4 Ethss. So
fill this value correctly in the knav dma descriptor.
Also rename dma_psflags field in struct netcp_tx_pipe to switch_to_port
as it contain no flag, but the switch port number for forwarding the
packet. Add a flag to hold the new flag, SWITCH_TO_PORT_IN_TAGINFO which
will be set for 10G. This can also used in the future for other flags for
the tx_pipe.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Mugunthan V N <mugunthanvnm@ti.com>
CC: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: Christoph Jaeger <cj@linux.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Markus Pargmann <mpa@pengutronix.de>
CC: Kumar Gala <galak@codeaurora.org>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Rob Herring <robh+dt@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Home routers based on ARM SoCs like BCM4708 also have bcma bus with core
supported by bgmac.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On ARM SoCs with bgmac Ethernet hardware we don't have any normal PHY.
There is always a switch attached but it's not even controlled over MDIO
like in case of MIPS devices.
We need a fixed PHY to be able to send/receive packets from the switch.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netif_carrier_off() first, since that will prevent the stack from
queuing more packets to this IF. This operation is fast, and should
behave much nicer when trying to bring down an interface under load.
Reported-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use netif_carrier_off() first, since that will prevent the stack from
queuing more packets to this IF. This operation is fast, and should
behave much nicer when trying to bring down an interface under load.
Reported-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The call to e1000e_write_protect_nvm_ich8lan() is no longer supported by HW.
Access to these registers causes a system freeze in A step hardware and is
ignored in B step hardware. This function must not be called in hardware
newer than LPT.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When bringing down an interface netif_carrier_off() should be
one the first things we do, since this will prevent the stack
from queuing more packets to this interface.
This operation is very fast, and should make the device behave
much nicer when trying to bring down an interface under load.
Also, this would Do The Right Thing (TM) if this device has some
sort of fail-over teaming and redirect traffic to the other IF.
Move netif_carrier_off as early as possible.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When bringing down an interface netif_carrier_off() should be
one the first things we do, since this will prevent the stack
from queuing more packets to this interface.
This operation is very fast, and should make the device behave
much nicer when trying to bring down an interface under load.
Also, this would Do The Right Thing (TM) if this device has some
sort of fail-over teaming and redirect traffic to the other IF.
Move netif_carrier_off as early as possible.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the napi_alloc_skb function to allocate an skb when running within
the softirq context to avoid calls to local_irq_save/restore.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Rx coalescing value is internally converted from usecs to a value
that the hardware can use. When reporting the Rx coalescing value, this
internal value is converted back to usecs. During the conversion from
and back to usecs some rounding occurs. So, for example, when setting an
Rx usec of 30, it will be reported as 29. Fix this reporting issue by
keeping the original usec value and using that during reporting.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx coalescing support in the driver was a software implementation
for something lacking in the hardware. Using hrtimers, the idea was to
trigger a timer interrupt after having queued a packet for transmit.
Unfortunately, as the timer value was lowered, the timer expired before
the hardware actually did the transmit and so it was racey and resulted
in unnecessary interrupts.
Remove the Tx coalescing support and hrtimer and replace with a Tx timer
that is used as a reclaim timer in case of inactivity.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware supplies a value that indicates the DMA range that it
is capable of using. Use this value rather than hard-coding it in
the driver.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new lighter weight memory barriers when working with the device
descriptors.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clarify that the queues referred to in a message when the device is
brought up are hardware queues and not necessarily related to the
Linux network queues.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, there is no interrupt code that indicates auto-negotiation
has timed out. If the auto-negotiation has timed out then the start of
a new auto-negotiation will begin again with a new base page being
received. The state machine could be in a state that is not expecting
this interrupt code which results in an error during auto-negotiation.
Update the code to timestamp when the auto-negotiation starts. Should
another page received interrupt code occur before auto-negotiation has
completed but after the auto-negotiation timeout, then reset the state
machine to allow the auto-negotiation to continue.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the setting of the transceiver type when retrieving the device
settings using ethtool and instead set the transceiver type in the
phy_driver structure flags field. Change the transceiver type to be
internal, also.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
