dccp_v4_err() can restrict lookups to ehash table, and not to listeners.
Note this patch creates the infrastructure, but this means that ICMP
messages for request sockets are ignored until complete conversion.
New dccp_req_err() helper is exported so that we can use it in IPv6
in following patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_v4_err() can restrict lookups to ehash table, and not to listeners.
Note this patch creates the infrastructure, but this means that ICMP
messages for request sockets are ignored until complete conversion.
New tcp_req_err() helper is exported so that we can use it in IPv6
in following patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a low hanging fruit, as we'll get rid of syn_wait_lock eventually.
We hold syn_wait_lock for such small sections, that it makes no sense to use
a read/write lock. A spin lock is simply faster.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not needed, and req->sk_listener points to the listener anyway.
request_sock argument can be const.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We send unicast neighbor (ARP or NDP) solicitations ucast_probes
times in PROBE state. Zhu Yanjun reported that some implementation
does not reply against them and the entry will become FAILED, which
is undesirable.
We had been dealt with such nodes by sending multicast probes mcast_
solicit times after unicast probes in PROBE state. In 2003, I made
a change not to send them to improve compatibility with IPv6 NDP.
Let's introduce per-protocol per-interface sysctl knob "mcast_
reprobe" to configure the number of multicast (re)solicitation for
reconfirmation in PROBE state. The default is 0, since we have
been doing so for 10+ years.
Reported-by: Zhu Yanjun <Yanjun.Zhu@windriver.com>
CC: Ulf Samuelsson <ulf.samuelsson@ericsson.com>
Signed-off-by: YOSHIFUJI Hideaki <hideaki.yoshifuji@miraclelinux.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suggested-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit ca10b9e9a8.
No longer needed after commit eb8895debe
("tcp: tcp_make_synack() should use sock_wmalloc")
When under SYNFLOOD, we build lot of SYNACK and hit false sharing
because of multiple modifications done on sk_listener->sk_wmem_alloc
Since tcp_make_synack() uses sock_wmalloc(), there is no need
to call skb_set_owner_w() again, as this adds two atomic operations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work extends the "classic" BPF programmable tc action by extending
its scope also to native eBPF code!
Together with commit e2e9b6541d ("cls_bpf: add initial eBPF support
for programmable classifiers") this adds the facility to implement fully
flexible classifier and actions for tc that can be implemented in a C
subset in user space, "safely" loaded into the kernel, and being run in
native speed when JITed.
Also, since eBPF maps can be shared between eBPF programs, it offers the
possibility that cls_bpf and act_bpf can share data 1) between themselves
and 2) between user space applications. That means that, f.e. customized
runtime statistics can be collected in user space, but also more importantly
classifier and action behaviour could be altered based on map input from
the user space application.
For the remaining details on the workflow and integration, see the cls_bpf
commit e2e9b6541d. Preliminary iproute2 part can be found under [1].
[1] http://git.breakpoint.cc/cgit/dborkman/iproute2.git/log/?h=ebpf-act
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to prepare eBPF support for tc action, we need to add
sched_act_type, so that the eBPF verifier is aware of what helper
function act_bpf may use, that it can load skb data and read out
currently available skb fields.
This is bascially analogous to 96be4325f4 ("ebpf: add sched_cls_type
and map it to sk_filter's verifier ops").
BPF_PROG_TYPE_SCHED_CLS and BPF_PROG_TYPE_SCHED_ACT need to be
separate since both will have a different set of functionality in
future (classifier vs action), thus we won't run into ABI troubles
when the point in time comes to diverge functionality from the
classifier.
The future plan for act_bpf would be that it will be able to write
into skb->data and alter selected fields mirrored in struct __sk_buff.
For an initial support, it's sufficient to map it to sk_filter_ops.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to include linux/errno.h in rhashtable.h since it doesn't
always get included otherwise.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all rhashtable users have been converted over to the
inline interface, this patch removes the unused out-of-line
interface.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch deals with the complaint that we make indirect function
calls on the fast paths unnecessarily in rhashtable. We resolve
it by moving the fast paths into inline functions that take struct
rhashtable_param (which obviously must be the same set of parameters
supplied to rhashtable_init) as an argument.
The only remaining indirect call is to obj_hashfn (or key_hashfn it
obj_hashfn is unset) on the rehash as well as the insert-during-
rehash slow path.
This patch also extends the support of vairable-length keys to
include those where the key is fixed but scattered in the object.
For example, in netlink we want to key off the namespace and the
portid but they're not next to each other.
This patch does this by directly using the object hash function
as the indicator of whether the key is accessible or not. It
also adds a new function obj_cmpfn to compare a key against an
object. This means that the caller no longer needs to supply
explicit compare functions.
All this is done in a backwards compatible manner so no existing
users are affected until they convert to the new interface.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch marks the rhashtable_init params argument const as
there is no reason to modify it since we will always make a copy
of it in the rhashtable.
This patch also fixes a bug where we don't actually round up the
value of min_size unless it is less than HASH_MIN_SIZE.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_ack_backlog & sk_max_ack_backlog were 16bit fields, meaning
listen() backlog was limited to 65535.
It is time to increase the width to allow much bigger backlog,
if admins change /proc/sys/net/core/somaxconn &
/proc/sys/net/ipv4/tcp_max_syn_backlog default values.
Tested:
echo 5000000 >/proc/sys/net/core/somaxconn
echo 5000000 >/proc/sys/net/ipv4/tcp_max_syn_backlog
Ran a SYNFLOOD test against a listener using listen(fd, 5000000)
myhost~# grep request_sock_TCP /proc/slabinfo
request_sock_TCP 4185642 4411940 304 13 1 : tunables 54 27 8 : slabdata 339380 339380 0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the major issue for TCP is the SYNACK rtx handling,
done by inet_csk_reqsk_queue_prune(), fired by the keepalive
timer of a TCP_LISTEN socket.
This function runs for awful long times, with socket lock held,
meaning that other cpus needing this lock have to spin for hundred of ms.
SYNACK are sent in huge bursts, likely to cause severe drops anyway.
This model was OK 15 years ago when memory was very tight.
We now can afford to have a timer per request sock.
Timer invocations no longer need to lock the listener,
and can be run from all cpus in parallel.
With following patch increasing somaxconn width to 32 bits,
I tested a listener with more than 4 million active request sockets,
and a steady SYNFLOOD of ~200,000 SYN per second.
Host was sending ~830,000 SYNACK per second.
This is ~100 times more what we could achieve before this patch.
Later, we will get rid of the listener hash and use ehash instead.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When request sock are put in ehash table, the whole notion
of having a previous request to update dl_next is pointless.
Also, following patch will get rid of big purge timer,
so we want to delete a request sock without holding listener lock.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix up consumer return values on pin control stubs.
- Four patches fixing up the interrupt handling and
sleep context save in the Baytrail driver.
- Make default output directions work properly in the
Cherryview driver.
- Fix interrupt locking in the AT91 driver.
- Fix setting interrupt generating lines as input in
the sunxi driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qp0z
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Here is a slew of pin control fixes I've accumulated for the v4.0
kernel. Nothing special, just driver fixes (mainly embedded Intel it
seems) and a misunderstanding regarding the stub functions was
reverted:
- Fix up consumer return values on pin control stubs.
- Four patches fixing up the interrupt handling and sleep context
save in the Baytrail driver.
- Make default output directions work properly in the Cherryview
driver.
- Fix interrupt locking in the AT91 driver.
- Fix setting interrupt generating lines as input in the sunxi
driver"
* tag 'pinctrl-v4.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: sun4i: GPIOs configured as irq must be set to input before reading
pinctrl: at91: move lock/unlock_as_irq calls into request/release
pinctrl: update direction_output function of cherryview driver
pinctrl: baytrail: Save pin context over system sleep
pinctrl: baytrail: Rework interrupt handling
pinctrl: baytrail: Clear interrupt triggering from pins that are in GPIO mode
pinctrl: baytrail: Relax GPIO request rules
Revert "pinctrl: consumer: use correct retval for placeholder functions"
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-03-19
This wont the last 4.1 bluetooth-next pull request, but we've piled up
enough patches in less than a week that I wanted to save you from a
single huge "last-minute" pull somewhere closer to the merge window.
The main changes are:
- Simultaneous LE & BR/EDR discovery support for HW that can do it
- Complete LE OOB pairing support
- More fine-grained mgmt-command access control (normal user can now do
harmless read-only operations).
- Added RF power amplifier support in cc2520 ieee802154 driver
- Some cleanups/fixes in ieee802154 code
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix packet header offset calculation in _decode_session6(), from
Hajime Tazaki.
2) Fix route leak in error paths of xfrm_lookup(), from Huaibin Wang.
3) Be sure to clear state properly when scans fail in iwlwifi mvm code,
from Luciano Coelho.
4) iwlwifi tries to stop scans that aren't actually running, also from
Luciano Coelho.
5) mac80211 should drop mesh frames that are not encrypted, fix from
Bob Copeland.
6) Add new device ID to b43 wireless driver for BCM432228 chips, from
Rafał Miłecki.
7) Fix accidental addition of members after variable sized array in
struct tc_u_hnode, from WANG Cong.
8) Don't re-enable interrupts until after we call napi_complete() in
ibmveth and WIZnet drivers, frm Yongbae Park.
9) Fix regression in vlan tag handling of fec driver, from Fugang Duan.
10) If a network namespace change fails during rtnl_newlink(), we don't
unwind the device registry properly.
11) Fix two TCP regressions, from Neal Cardwell:
- Don't allow snd_cwnd_cnt to accumulate huge values due to missing
test in tcp_cong_avoid_ai().
- Restore CUBIC back to advancing cwnd by 1.5x packets per RTT.
12) Fix performance regression in xne-netback involving push TX
notifications, from David Vrabel.
13) __skb_tstamp_tx() can be called with a NULL sk pointer, do not
dereference blindly. From Willem de Bruijn.
14) Fix potential stack overflow in RDS protocol stack, from Arnd
Bergmann.
15) VXLAN_VID_MASK used incorrectly in new remote checksum offload
support of VXLAN driver. Fix from Alexey Kodanev.
16) Fix too small netlink SKB allocation in inet_diag layer, from Eric
Dumazet.
17) ieee80211_check_combinations() does not count interfaces correctly,
from Andrei Otcheretianski.
18) Hardware feature determination in bxn2x driver references a piece of
software state that actually isn't initialized yet, fix from Michal
Schmidt.
19) inet_csk_wait_for_connect() needs a sched_annotate_sleep()
annoation, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (56 commits)
Revert "net: cx82310_eth: use common match macro"
net/mlx4_en: Set statistics bitmap at port init
IB/mlx4: Saturate RoCE port PMA counters in case of overflow
net/mlx4_en: Fix off-by-one in ethtool statistics display
IB/mlx4: Verify net device validity on port change event
act_bpf: allow non-default TC_ACT opcodes as BPF exec outcome
Revert "smc91x: retrieve IRQ and trigger flags in a modern way"
inet: Clean up inet_csk_wait_for_connect() vs. might_sleep()
ip6_tunnel: fix error code when tunnel exists
netdevice.h: fix ndo_bridge_* comments
bnx2x: fix encapsulation features on 57710/57711
mac80211: ignore CSA to same channel
nl80211: ignore HT/VHT capabilities without QoS/WMM
mac80211: ask for ECSA IE to be considered for beacon parse CRC
mac80211: count interfaces correctly for combination checks
isdn: icn: use strlcpy() when parsing setup options
rxrpc: bogus MSG_PEEK test in rxrpc_recvmsg()
caif: fix MSG_OOB test in caif_seqpkt_recvmsg()
bridge: reset bridge mtu after deleting an interface
can: kvaser_usb: Fix tx queue start/stop race conditions
...
When a networking device is taken down that has a non-trivial number
of VLAN devices configured under it, we eat a full synchronize_net()
for every such VLAN device.
This is because of the call chain:
NETDEV_DOWN notifier
--> vlan_device_event()
--> dev_change_flags()
--> __dev_change_flags()
--> __dev_close()
--> __dev_close_many()
--> dev_deactivate_many()
--> synchronize_net()
This is kind of rediculous because we already have infrastructure for
batching doing operation X to a list of net devices so that we only
incur one sync.
So make use of that by exporting dev_close_many() and adjusting it's
interfaace so that the caller can fully manage the batch list. Use
this in vlan_device_event() and all the overhead goes away.
Reported-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to port id allow netdevices to specify port names and export
the name via sysfs. Drivers can implement the netdevice operation to
assist udev in having sane default names for the devices using the
rule:
$ cat /etc/udev/rules.d/80-net-setup-link.rules
SUBSYSTEM=="net", ACTION=="add", ATTR{phys_port_name}!="",
NAME="$attr{phys_port_name}"
Use of phys_name versus phys_id was suggested-by Jiri Pirko.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in favor of their inner __ ones, which doesn't grab rtnl.
As these functions need to operate on a locked socket, we can't be
grabbing rtnl by then. It's too late and doing so causes reversed
locking.
So this patch:
- move rtnl handling to callers instead while already fixing some
reversed locking situations, like on vxlan and ipvs code.
- renames __ ones to not have the __ mark:
__ip_mc_{join,leave}_group -> ip_mc_{join,leave}_group
__ipv6_sock_mc_{join,drop} -> ipv6_sock_mc_{join,drop}
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to be able to use sk_ehashfn() for request socks,
we need to initialize their IPv6/IPv4 addresses.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now always call __inet_hash_nolisten(), no need to pass it
as an argument.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can now use inet_hash() and __inet_hash() instead of private
functions.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Intent is to converge IPv4 & IPv6 inet_hash functions to
factorize code.
IPv4 sockets initialize sk_rcv_saddr and sk_v6_daddr
in this patch, thanks to new sk_daddr_set() and sk_rcv_saddr_set()
helpers.
__inet6_hash can now use sk_ehashfn() instead of a private
inet6_sk_ehashfn() and will simply use __inet_hash() in a
following patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Goal is to unify IPv4/IPv6 inet_hash handling, and use common helpers
for all kind of sockets (full sockets, timewait and request sockets)
inet_sk_ehashfn() becomes sk_ehashfn() but still only copes with IPv4
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
const qualifiers ease code review by making clear
which objects are not written in a function.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the low-level device commands and definitions used for QP max-rate limiting.
This is done through the following elements:
- read rate-limit device caps in QUERY_DEV_CAP: number of different
rates and the min/max rates in Kbs/Mbs/Gbs units
- enhance the QP context struct to contain rate limit units and value
- allow to do run time rate-limit setting to QPs through the
update-qp firmware command
- QP rate-limiting is disallowed for VFs
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a tx_maxrate attribute to the tx queue sysfs entry allowing
for max-rate limiting. Along with DCB-ETS and BQL this provides another
knob to tune queue performance. The limit units are Mbps.
By default it is disabled. To disable the rate limitation after it
has been set for a queue, it should be set to zero.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull livepatching fix from Jiri Kosina:
- fix for potential race with module loading, from Petr Mladek.
The race is very unlikely to be seen in real world and has been found
by code inspection, but should be fixed for 4.0 anyway.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
livepatch: Fix subtle race with coming and going modules
The TI CC2521 is an RF power amplifier that is designed to interface
with the CC2520. Conveniently, it directly interfaces with the CC2520
and does not require any pins to be connected to a
microcontroller/processor. Adding a CC2591 increases the CC2520's range,
which is useful for border router and other wall-powered applications.
Using the CC2591 with the CC2520 requires configuring the CC2520 GPIOs
that are connected to the CC2591 to correctly set the CC2591 into TX and
RX modes. Further, TI recommends that the CC2520_TXPOWER and
CC2520_AGCCTRL1 registers are set differently to maximize the CC2591's
performance. These settings are covered in TI Application Note AN065.
This patch adds an optional `amplified` field to the cc2520 entry in the
device tree. If present, the CC2520 will be configured to operate with a
CC2591.
The expected pin mapping is:
CC2520 GPIO0 --> CC2591 EN
CC2520 GPIO5 --> CC2591 PAEN
Signed-off-by: Brad Campbell <bradjc5@gmail.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that nobody uses max_shift and min_shift, we can safely remove
them.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the parameters max_size and min_size which are
meant to replace max_shift and min_shift.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keeping both size and shift is silly. We only need one.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing last patch series, I found req sock refcounting was wrong.
We must set skc_refcnt to 1 for all request socks added in hashes,
but also on request sockets created by FastOpen or syncookies.
It is tricky because we need to defer this initialization so that
future RCU lookups do not try to take a refcount on a not yet
fully initialized request socket.
Also get rid of ireq_refcnt alias.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 13854e5a60 ("inet: add proper refcounting to request sock")
Signed-off-by: David S. Miller <davem@davemloft.net>
The listener field in struct tcp_request_sock is a pointer
back to the listener. We now have req->rsk_listener, so TCP
only needs one boolean and not a full pointer.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once we'll be able to lookup request sockets in ehash table,
we'll need to get access to listener which created this request.
This avoid doing a lookup to find the listener, which benefits
for a more solid SO_REUSEPORT, and is needed once we no
longer queue request sock into a listener private queue.
Note that 'struct tcp_request_sock'->listener could be reduced
to a single bit, as TFO listener should match req->rsk_listener.
TFO will no longer need to hold a reference on the listener.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet_reqsk_alloc() is becoming fat and should not be inlined.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
listener socket can be used to set net pointer, and will
be later used to hold a reference on listener.
Add a const qualifier to first argument (struct request_sock_ops *),
and factorize all write_pnet(&ireq->ireq_net, sock_net(sk));
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_oow_rate_limited() is hardly used in fast path, there is
no point inlining it.
Signed-of-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This big helper is called once from tcp_conn_request(), there is no
point having it in an include. Compiler will inline it anyway.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 64bit arches, we can save 8 bytes in inet_request_sock
by moving ir_mark to fill a hole.
While we are at it, inet_request_mark() can get a const qualifier
for listener socket.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
as a follow on to patch 70006af955 ("bpf: allow eBPF access skb fields")
this patch allows 'protocol' and 'vlan_tci' fields to be accessible
from extended BPF programs.
The usage of 'protocol', 'vlan_present' and 'vlan_tci' fields is the same as
corresponding SKF_AD_PROTOCOL, SKF_AD_VLAN_TAG_PRESENT and SKF_AD_VLAN_TAG
accesses in classic BPF.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The argument 'flags' was missing in ndo_bridge_setlink().
ndo_bridge_dellink() was missing.
Fixes: 407af3299e ("bridge: Add netlink interface to configure vlans on bridge ports")
Fixes: add511b382 ("bridge: add flags argument to ndo_bridge_setlink and ndo_bridge_dellink")
CC: Vlad Yasevich <vyasevic@redhat.com>
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
more minor issues with our virtio 1.0 drivers just introduced in the
kernel.
(I would normally use my fixes branch for this, but there were a batch of them...)
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8QwR
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio fixes from Rusty Russell:
"Not entirely surprising: the ongoing QEMU work on virtio 1.0 has
revealed more minor issues with our virtio 1.0 drivers just introduced
in the kernel.
(I would normally use my fixes branch for this, but there were a batch
of them...)"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio_mmio: fix access width for mmio
uapi/virtio_scsi: allow overriding CDB/SENSE size
virtio_mmio: generation support
virtio_rpmsg: set DRIVER_OK before using device
9p/trans_virtio: fix hot-unplug
virtio-balloon: do not call blocking ops when !TASK_RUNNING
virtio_blk: fix comment for virtio 1.0
virtio_blk: typo fix
virtio_balloon: set DRIVER_OK before using device
virtio_console: avoid config access from irq
virtio_console: init work unconditionally
