Commit 761ed4a94582 ("tty: serial_core: convert uart_close to use
tty_port_close") created a case where a port used for a console does not
get shutdown on tty closing. Then a call to uart_tx_stopped() segfaults
because the tty is NULL. This could be fixed to restore old behavior,
but we also want to allow tty_ports to work without a tty attached. So
this change to allow a NULL tty_struct is needed either way.
Fixes: 761ed4a94582
("tty: serial_core: convert uart_close to use tty_port_close")
Reported-by: kernel test robot <xiaolong.ye@intel.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change-Id: Ifbeeacc89d396b857332ce94cc2d77bdd6e12bb7
Git-repo: git://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git
Git-commit: a727b025f43d7952c0697562f5cecda9f42758aa
Signed-off-by: Lei wang <leiwan@codeaurora.org>
Currently, FULL_SOC and MONOTONIC_SOC registers are updated
multiple times when the recharge SOC threshold is close enough to
trigger the recharging frequently. This was leading to a SOC
fluctuation when SOC masking algorithm is enabled.
Rearrange charge_full_update used in SOC masking algorithm such
that FULL_SOC and MONOTONIC_SOC registers are updated just once
when the charge_full flag is cleared.
Also, when the device is rebooted/shutdown and if charge_full
flag is set, write to FULL_SOC with battery_soc and a full value
to MONOTONIC_SOC registers. This helps to maintain the same SOC
across a device reboot.
Change-Id: I95afa90f27e4c0f948f301ff8d6a1f84ae422ef0
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
Add a device tree node for the SPI CAN controller to enable
a CAN network interface for msm8996 CV2X boards.
Change-Id: Ib9c1d63bf86e3b823aa8d762065ed374bdfeaa0e
Signed-off-by: Gustavo Solaira <gustavos@codeaurora.org>
Enable configuration for K61 CAN over SPI driver.
Change-Id: I801629ac04303582530bed354282960db8f9c9ab
Signed-off-by: Gustavo Solaira <gustavos@codeaurora.org>
Add new parameters to account for different MCUs that can
be used with this driver. These devices have different reset
sequences and number of bits per word supported via SPI. Add
bindings for the mpc5746c controller and make the reset signal
optional.
Change-Id: I616dd3cfedf18a6e21683e1c07551c57c62a675d
Signed-off-by: Gustavo Solaira <gustavos@codeaurora.org>
This driver creates Network device of type CAN
and processes tx and rx frames that it sends and
receives over SPI protocol.
Change-Id: I54a8665d1b9eda7e9b1ff695bd67de312c410195
Signed-off-by: Gustavo Solaira <gustavos@codeaurora.org>
Signed-off-by: Abinaya P <abinayap@codeaurora.org>
The patch adds the support for buffering mode configuration
for peripherals not supporting diag_id.
CRs-Fixed: 2104591
Change-Id: I2ed34a5141a9b9042dc925c9109d22009b272484
Signed-off-by: Manoj Prabhu B <bmanoj@codeaurora.org>
Increase QMI ATHDIAG maximum data size to 6144 bytes so that it
can dump more bytes for debugging.
Change-Id: I21d6197ad67829c38586318d4e76a7c7fd4149c4
CRs-fixed: 2059087
Signed-off-by: Yue Ma <yuem@codeaurora.org>
Current SD card resume function does not handle card
init failure but only prints resume error message.
This change powers off mmc host before exit resume
if card init fails.
Change-Id: Idc27d8ed8769b92373bb9770f5e706b18e76404d
Signed-off-by: Can Guo <cang@codeaurora.org>
The WFD setup path has few register writes. If the MDP clocks
aren't switched on, the register access might cause SMMU
faults. Turn on the clocks, before calling WFD setup.
Change-Id: Icc865178f43dc6068b6b4b201b8f9eada2570598
Signed-off-by: Krishna Chaitanya Devarakonda <kdevarak@codeaurora.org>
There is a race condition possible when two threads are calling
the rotator cancel request. This might result in accessing a pointer
which was already assigned NULL. Fixing this by adding an extra check.
Change-Id: I9ce321a5f033d1fdc9d8b70a04098bfba3d7baaa
Signed-off-by: Krishna Chaitanya Devarakonda <kdevarak@codeaurora.org>
Provide means to suspend the DC path using the power supply
property.
Change-Id: I97f83f5f7c892fc078a92914af0a923b6aacf02e
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Implement several IOCTLs to allow IPA user space work.
Change-Id: I726f665ada12c5524dabeab1b89cdc8db4dc6f1e
Acked-by: Dmitry Kogan <dmitryk@qti.qualcomm.com>
Signed-off-by: Amir Levy <alevy@codeaurora.org>
If this quirk is set, then data timeout interrupt must not be
handled for R1B commands, as those commands may need larger
timeout value (larger than max timeout that controller can handle).
Change-Id: I7453b1914add21b47393b3eb1578d88e72da7406
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Add the changes to support the 1080p truly panel as default panel
for SDM636.
Change-Id: Ia6d9b26fb7efb1d8ed362da42e3b6f22798f6f5e
Signed-off-by: Rashi Bindra <rbindra@codeaurora.org>
