[ Upstream commit 916a008b4b8ecc02fbd035cfb133773dba1ff3d7 ]
dma_get_sgtable() tries to create a scatterlist table containing valid
struct page pointers for the coherent memory allocation passed in to it.
However, memory can be declared via dma_declare_coherent_memory(), or
via other reservation schemes which means that coherent memory is not
guaranteed to be backed by struct pages. In such cases, the resulting
scatterlist table contains pointers to invalid pages, which causes
kernel oops later.
This patch adds detection of such memory, and refuses to create a
scatterlist table for such memory.
Reported-by: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9bcf53f34a2c1cebc45cc12e273dcd5f51fbc099 ]
mmc2 used for wl12xx was missing the keep-power-in suspend
parameter. As a result the board couldn't reach suspend state.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 974310d047f3c7788a51d10c8d255eebdb1fa857 ]
kprobes test cases need to have a stack that is aligned to an 8-byte
boundary because they call other functions (and the ARM ABI mandates
that alignment) and because test cases include 64-bit accesses to the
stack. Unfortunately, GCC doesn't ensure this alignment for inline
assembler and for the code in question seems to always misalign it by
pushing just the LR register onto the stack. We therefore need to
explicitly perform stack alignment at the start of each test case.
Without this fix, some test cases will generate alignment faults on
systems where alignment is enforced. Even if the kernel is configured to
handle these faults in software, triggering them is ugly. It also
exposes limitations in the fault handling code which doesn't cope with
writes to the stack. E.g. when handling this instruction
strd r6, [sp, #-64]!
the fault handling code will write to a stack location below the SP
value at the point the fault occurred, which coincides with where the
exception handler has pushed the saved register context. This results in
corruption of those registers.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef0491ea17f8019821c7e9c8e801184ecf17f85a upstream.
The introduction of switch_mm_irqs_off() brought back an old bug
regarding the use of preempt_enable_no_resched:
As part of:
62b94a08da ("sched/preempt: Take away preempt_enable_no_resched() from modules")
the definition of preempt_enable_no_resched() is only available in
built-in code, not in loadable modules, so we can't generally use
it from header files.
However, the ARM version of finish_arch_post_lock_switch()
calls preempt_enable_no_resched() and is defined as a static
inline function in asm/mmu_context.h. This in turn means we cannot
include asm/mmu_context.h from modules.
With today's tip tree, asm/mmu_context.h gets included from
linux/mmu_context.h, which is normally the exact pattern one would
expect, but unfortunately, linux/mmu_context.h can be included from
the vhost driver that is a loadable module, now causing this compile
time error with modular configs:
In file included from ../include/linux/mmu_context.h:4:0,
from ../drivers/vhost/vhost.c:18:
../arch/arm/include/asm/mmu_context.h: In function 'finish_arch_post_lock_switch':
../arch/arm/include/asm/mmu_context.h:88:3: error: implicit declaration of function 'preempt_enable_no_resched' [-Werror=implicit-function-declaration]
preempt_enable_no_resched();
Andy already tried to fix the bug by including linux/preempt.h
from asm/mmu_context.h, but that didn't help. Arnd suggested reordering
the header files, which wasn't popular, so let's use this
workaround instead:
The finish_arch_post_lock_switch() definition is now also hidden
inside of #ifdef MODULE, so we don't see anything referencing
preempt_enable_no_resched() from a header file. I've built a
few hundred randconfig kernels with this, and did not see any
new problems.
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King - ARM Linux <linux@armlinux.org.uk>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: linux-arm-kernel@lists.infradead.org
Fixes: f98db6013c55 ("sched/core: Add switch_mm_irqs_off() and use it in the scheduler")
Link: http://lkml.kernel.org/r/1463146234-161304-1-git-send-email-arnd@arndb.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5553b142be11e794ebc0805950b2e8313f93d718 upstream.
VTTBR_BADDR_MASK is used to sanity check the size and alignment of the
VTTBR address. It seems to currently be off by one, thereby only
allowing up to 39-bit addresses (instead of 40-bit) and also
insufficiently checking the alignment. This patch fixes it.
This patch is the 32bit pendent of Kristina's arm64 fix, and
she deserves the actual kudos for pinpointing that one.
Fixes: f7ed45be3b ("KVM: ARM: World-switch implementation")
Cc: <stable@vger.kernel.org> # 3.9
Reported-by: Kristina Martsenko <kristina.martsenko@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f050fe7a9164945dd1c28be05bf00e8cfb082ccf ]
Currently we BUG() if we see a HSR.EC value we don't recognise. As
configurable disables/enables are added to the architecture (controlled
by RES1/RES0 bits respectively), with associated synchronous exceptions,
it may be possible for a guest to trigger exceptions with classes that
we don't recognise.
While we can't service these exceptions in a manner useful to the guest,
we can avoid bringing down the host. Per ARM DDI 0406C.c, all currently
unallocated HSR EC encodings are reserved, and per ARM DDI
0487A.k_iss10775, page G6-4395, EC values within the range 0x00 - 0x2c
are reserved for future use with synchronous exceptions, and EC values
within the range 0x2d - 0x3f may be used for either synchronous or
asynchronous exceptions.
The patch makes KVM handle any unknown EC by injecting an UNDEFINED
exception into the guest, with a corresponding (ratelimited) warning in
the host dmesg. We could later improve on this with with a new (opt-in)
exit to the host userspace.
Cc: Dave Martin <dave.martin@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b92675d998a9fa37fe9e0e35053a95b4a23c158b ]
The device node returned by of_find_node_by_name() needs to be released
after it is no longer needed to avoid a device node leak.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 10e5778f54765c96fe0c8f104b7a030e5b35bc72 ]
After commit 0549bde0fcb1 ("of: fix of_node leak caused in
of_find_node_opts_by_path"), the following error may be
reported when running omap images.
OF: ERROR: Bad of_node_put() on /ocp@68000000
CPU: 0 PID: 0 Comm: swapper Not tainted 4.10.0-rc7-next-20170210 #1
Hardware name: Generic OMAP3-GP (Flattened Device Tree)
[<c0310604>] (unwind_backtrace) from [<c030bbf4>] (show_stack+0x10/0x14)
[<c030bbf4>] (show_stack) from [<c05add8c>] (dump_stack+0x98/0xac)
[<c05add8c>] (dump_stack) from [<c05af1b0>] (kobject_release+0x48/0x7c)
[<c05af1b0>] (kobject_release)
from [<c0ad1aa4>] (of_find_node_by_name+0x74/0x94)
[<c0ad1aa4>] (of_find_node_by_name)
from [<c1215bd4>] (omap3xxx_hwmod_is_hs_ip_block_usable+0x24/0x2c)
[<c1215bd4>] (omap3xxx_hwmod_is_hs_ip_block_usable) from
[<c1215d5c>] (omap3xxx_hwmod_init+0x180/0x274)
[<c1215d5c>] (omap3xxx_hwmod_init)
from [<c120faa8>] (omap3_init_early+0xa0/0x11c)
[<c120faa8>] (omap3_init_early)
from [<c120fb2c>] (omap3430_init_early+0x8/0x30)
[<c120fb2c>] (omap3430_init_early)
from [<c1204710>] (setup_arch+0xc04/0xc34)
[<c1204710>] (setup_arch) from [<c1200948>] (start_kernel+0x68/0x38c)
[<c1200948>] (start_kernel) from [<8020807c>] (0x8020807c)
of_find_node_by_name() drops the reference to the passed device node.
The commit referenced above exposes this problem.
To fix the problem, use of_get_child_by_name() instead of
of_find_node_by_name(); of_get_child_by_name() does not drop
the reference count of passed device nodes. While semantically
different, we only look for immediate children of the passed
device node, so of_get_child_by_name() is a more appropriate
function to use anyway.
Release the reference to the device node obtained with
of_get_child_by_name() after it is no longer needed to avoid
another device node leak.
While at it, clean up the code and change the return type of
omap3xxx_hwmod_is_hs_ip_block_usable() to bool to match its use
and the return type of of_device_is_available().
Cc: Qi Hou <qi.hou@windriver.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3aaf33bebda8d4ffcc0fc8ef39e6c1ac68823b11 upstream.
When qemu starts a kernel in a bare environment, the default SCR has
the AW and FW bits clear, which means that the kernel can't modify
the PSR A or PSR F bits, and means that FIQs and imprecise aborts are
always masked.
When running uboot under qemu, the AW and FW SCR bits are set, and the
kernel functions normally - and this is how real hardware behaves.
Fix this for qemu by ignoring the FIQ bit.
Fixes: 8bafae202c82 ("ARM: BUG if jumping to usermode address in kernel mode")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Alex Shi <alex.shi@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8bafae202c82dc257f649ea3c275a0f35ee15113 upstream.
Detect if we are returning to usermode via the normal kernel exit paths
but the saved PSR value indicates that we are in kernel mode. This
could occur due to corrupted stack state, which has been observed with
"ftracetest".
This ensures that we catch the problem case before we get to user code.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Alex Shi <alex.shi@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 657279778af54f35e54b07b6687918f254a2992c ]
OMAP1510, OMAP5910 and OMAP310 have only 9 logical channels.
OMAP1610, OMAP5912, OMAP1710, OMAP730, and OMAP850 have 16 logical channels
available.
The wired 17 for the lch_count must have been used to cover the 16 + 1
dedicated LCD channel, in reality we can only use 9 or 16 channels.
The d->chan_count is not used by the omap-dma stack, so we can skip the
setup. chan_count was configured to the number of logical channels and not
the actual number of physical channels anyways.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7ace5ed8867ca54503727988adec6b20af54eeb upstream.
Fixes commit 687c276761 ("ARM: dts: Add minimal support for LogicPD
Torpedo DM3730 devkit")
This patch corrects an issue where the cd-gpios was improperly setup
using IRQ_TYPE_LEVEL_LOW instead of GPIO_ACTIVE_LOW.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b0c0c922ff4be275a8beb87ce5657d16f355b54 upstream.
When CONFIG_ARM_LPAE is set, the PMD dump relies on the software
read-only bit to determine whether a page is writable. This
concealed a bug which left the kernel text section writable
(AP2=0) while marked read-only in the software bit.
In a kernel with the AP2 bug, the dump looks like this:
---[ Kernel Mapping ]---
0xc0000000-0xc0200000 2M RW NX SHD
0xc0200000-0xc0600000 4M ro x SHD
0xc0600000-0xc0800000 2M ro NX SHD
0xc0800000-0xc4800000 64M RW NX SHD
The fix is to check that the software and hardware bits are both
set before displaying "ro". The dump then shows the true perms:
---[ Kernel Mapping ]---
0xc0000000-0xc0200000 2M RW NX SHD
0xc0200000-0xc0600000 4M RW x SHD
0xc0600000-0xc0800000 2M RW NX SHD
0xc0800000-0xc4800000 64M RW NX SHD
Fixes: ded9477984 ("ARM: 8109/1: mm: Modify pte_write and pmd_write logic for LPAE")
Signed-off-by: Philip Derrin <philip@cog.systems>
Tested-by: Neil Dick <neil@cog.systems>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 400eeffaffc7232c0ae1134fe04e14ae4fb48d8c upstream.
Currently, for ARM kernels with CONFIG_ARM_LPAE and
CONFIG_STRICT_KERNEL_RWX enabled, the 2MiB pages mapping the
kernel code and rodata are writable. They are marked read-only in
a software bit (L_PMD_SECT_RDONLY) but the hardware read-only bit
is not set (PMD_SECT_AP2).
For user mappings, the logic that propagates the software bit
to the hardware bit is in set_pmd_at(); but for the kernel,
section_update() writes the PMDs directly, skipping this logic.
The fix is to set PMD_SECT_AP2 for read-only sections in
section_update(), at the same time as L_PMD_SECT_RDONLY.
Fixes: 1e3479225a ("ARM: 8275/1: mm: fix PMD_SECT_RDONLY undeclared compile error")
Signed-off-by: Philip Derrin <philip@cog.systems>
Reported-by: Neil Dick <neil@cog.systems>
Tested-by: Neil Dick <neil@cog.systems>
Tested-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6e613ebf4405fc09e2a8c16ed193b47f80a3cbed ]
It's possible that there are multiple quirks that need to be initialized
for the same SoC. Fix the issue by not returning on the first match.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1aa09df0854efe16b7a80358a18f0a0bebafd246 ]
Without these changes children of the scn syscon
won't probe.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f62280efe8934a1275fd148ef302d1afec8cd3df ]
When using 8250_omap driver, we need to specify the right
compatible value for the UART to work on dm814x and dm816x.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Not upstream because this is a minimal fix for a bug where arm32
kernels can use a much slower implementation of AES than is actually
available, potentially forcing vendors to disable encryption on their
devices.]
All the aes-bs (bit-sliced) and aes-ce (cryptographic extensions)
algorithms had a priority of 300. This is undesirable because it means
an aes-bs algorithm may be used when an aes-ce algorithm is available.
The aes-ce algorithms have much better performance (up to 10x faster).
Fix it by decreasing the priority of the aes-bs algorithms to 250.
This was fixed upstream by commit cc477bf64573 ("crypto: arm/aes -
replace bit-sliced OpenSSL NEON code"), but it was just a small part of
a complete rewrite. This patch just fixes the priority bug for older
kernels.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
commit b9dd05c7002ee0ca8b676428b2268c26399b5e31 upstream.
When CONFIG_DEBUG_USER is enabled, it's possible for a user to
deliberately trigger dump_instr() with a chosen kernel address.
Let's avoid problems resulting from this by using get_user() rather than
__get_user(), ensuring that we don't erroneously access kernel memory.
So that we can use the same code to dump user instructions and kernel
instructions, the common dumping code is factored out to __dump_instr(),
with the fs manipulated appropriately in dump_instr() around calls to
this.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4cd6a59f5c1a9b0cca0da09fbba42b9450ffc899 ]
We have more than four uarts on some SoCs and that can cause
noise with errors while booting.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 40d727a2defa176b78159d445bcf7afcc2ed9021 ]
Some of the pxa platforms, balloon3, colibri-pxa270-income, corgi,
trizeps4, vpac270, zeus and zylonite depends on leds.h. Explicitly include
it instead of relying on the public mmc header host.h.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1cce91dfc8f7990ca3aea896bfb148f240b12860 upstream.
The asm-generic/unaligned.h header provides two different implementations
for accessing unaligned variables: the access_ok.h version used when
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is set pretends that all pointers
are in fact aligned, while the le_struct.h version convinces gcc that the
alignment of a pointer is '1', to make it issue the correct load/store
instructions depending on the architecture flags.
On ARMv5 and older, we always use the second version, to let the compiler
use byte accesses. On ARMv6 and newer, we currently use the access_ok.h
version, so the compiler can use any instruction including stm/ldm and
ldrd/strd that will cause an alignment trap. This trap can significantly
impact performance when we have to do a lot of fixups and, worse, has
led to crashes in the LZ4 decompressor code that does not have a trap
handler.
This adds an ARM specific version of asm/unaligned.h that uses the
le_struct.h/be_struct.h implementation unconditionally. This should lead
to essentially the same code on ARMv6+ as before, with the exception of
using regular load/store instructions instead of the trapping instructions
multi-register variants.
The crash in the LZ4 decompressor code was probably introduced by the
patch replacing the LZ4 implementation, commit 4e1a33b105dd ("lib: update
LZ4 compressor module"), so linux-4.11 and higher would be affected most.
However, we probably want to have this backported to all older stable
kernels as well, to help with the performance issues.
There are two follow-ups that I think we should also work on, but not
backport to stable kernels, first to change the asm-generic version of
the header to remove the ARM special case, and second to review all
other uses of CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS to see if they
might be affected by the same problem on ARM.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cda80a82ac3e89309706c027ada6ab232be1d640 upstream.
Under heavy system stress mvebu SoC using Cortex A9 sporadically
encountered instability issues.
The "double linefill" feature of L2 cache was identified as causing
dependency between read and write which lead to the deadlock.
Especially, it was the cause of deadlock seen under heavy PCIe traffic,
as this dependency violates PCIE overtaking rule.
Fixes: c8f5a878e5 ("ARM: mvebu: use DT properties to fine-tune the L2 configuration")
Signed-off-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
[gregory.clement@free-electrons.com: reformulate commit log, add Armada
375 and add Fixes tag]
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8a792e9afbce84a0fdaf213fe42bb97382487094 ]
REMAP_VECTORS_TO_RAM depends on DRAM_BASE, but since DRAM_BASE is a
hex, REMAP_VECTORS_TO_RAM could never get enabled. Also depending on
DRAM_BASE is redundant as whenever REMAP_VECTORS_TO_RAM makes itself
available to Kconfig, DRAM_BASE also is available as the Kconfig
gets sourced on !MMU.
Signed-off-by: Afzal Mohammed <afzal.mohd.ma@gmail.com>
Reviewed-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 654450baf2afba86cf328e1849ccac61ec4630af ]
Use recently added R-Car Gen 2 fallback binding for msiof nodes in
DT for r8a7790 SoC.
This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7790 and the
fallback binding for R-Car Gen 2.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c35430ad18f5a034302cb90e559ede5a27f93b9 upstream.
The number of requestor lines was clamped to 0 for all pxa architectures
in the requestor declaration. Fix this by using the value.
Fixes: 72b195cb7162 ("ARM: pxa: add the number of DMA requestor lines")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72b195cb716284217e8b270af420bc7e5cf04b3c upstream.
Declare the number of DMA requestor lines per platform :
- for pxa25x: 40 requestor lines
- for pxa27x: 75 requestor lines
- for pxa3xx: 100 requestor lines
This information will be used to activate the DMA flow control or not.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 746a272e44141af24a02f6c9b0f65f4c4598ed42 upstream.
When there's a fatal signal pending, arm's do_page_fault()
implementation returns 0. The intent is that we'll return to the
faulting userspace instruction, delivering the signal on the way.
However, if we take a fatal signal during fixing up a uaccess, this
results in a return to the faulting kernel instruction, which will be
instantly retried, resulting in the same fault being taken forever. As
the task never reaches userspace, the signal is not delivered, and the
task is left unkillable. While the task is stuck in this state, it can
inhibit the forward progress of the system.
To avoid this, we must ensure that when a fatal signal is pending, we
apply any necessary fixup for a faulting kernel instruction. Thus we
will return to an error path, and it is up to that code to make forward
progress towards delivering the fatal signal.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2952a6070e07ebdd5896f1f5b861acad677caded upstream.
Make sure we don't use a cached value of the KVM stage2 PGD while
resetting the PGD.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c0d706b563af732adb094c5bf807437e8963e84 upstream.
In kvm_free_stage2_pgd() we check the stage2 PGD before holding
the lock and proceed to take the lock if it is valid. And we unmap
the page tables, followed by releasing the lock. We reset the PGD
only after dropping this lock, which could cause a race condition
where another thread waiting on or even holding the lock, could
potentially see that the PGD is still valid and proceed to perform
a stage2 operation and later encounter a NULL PGD.
[223090.242280] Unable to handle kernel NULL pointer dereference at
virtual address 00000040
[223090.262330] PC is at unmap_stage2_range+0x8c/0x428
[223090.262332] LR is at kvm_unmap_hva_handler+0x2c/0x3c
[223090.262531] Call trace:
[223090.262533] [<ffff0000080adb78>] unmap_stage2_range+0x8c/0x428
[223090.262535] [<ffff0000080adf40>] kvm_unmap_hva_handler+0x2c/0x3c
[223090.262537] [<ffff0000080ace2c>] handle_hva_to_gpa+0xb0/0x104
[223090.262539] [<ffff0000080af988>] kvm_unmap_hva+0x5c/0xbc
[223090.262543] [<ffff0000080a2478>]
kvm_mmu_notifier_invalidate_page+0x50/0x8c
[223090.262547] [<ffff0000082274f8>]
__mmu_notifier_invalidate_page+0x5c/0x84
[223090.262551] [<ffff00000820b700>] try_to_unmap_one+0x1d0/0x4a0
[223090.262553] [<ffff00000820c5c8>] rmap_walk+0x1cc/0x2e0
[223090.262555] [<ffff00000820c90c>] try_to_unmap+0x74/0xa4
[223090.262557] [<ffff000008230ce4>] migrate_pages+0x31c/0x5ac
[223090.262561] [<ffff0000081f869c>] compact_zone+0x3fc/0x7ac
[223090.262563] [<ffff0000081f8ae0>] compact_zone_order+0x94/0xb0
[223090.262564] [<ffff0000081f91c0>] try_to_compact_pages+0x108/0x290
[223090.262569] [<ffff0000081d5108>] __alloc_pages_direct_compact+0x70/0x1ac
[223090.262571] [<ffff0000081d64a0>] __alloc_pages_nodemask+0x434/0x9f4
[223090.262572] [<ffff0000082256f0>] alloc_pages_vma+0x230/0x254
[223090.262574] [<ffff000008235e5c>] do_huge_pmd_anonymous_page+0x114/0x538
[223090.262576] [<ffff000008201bec>] handle_mm_fault+0xd40/0x17a4
[223090.262577] [<ffff0000081fb324>] __get_user_pages+0x12c/0x36c
[223090.262578] [<ffff0000081fb804>] get_user_pages_unlocked+0xa4/0x1b8
[223090.262579] [<ffff0000080a3ce8>] __gfn_to_pfn_memslot+0x280/0x31c
[223090.262580] [<ffff0000080a3dd0>] gfn_to_pfn_prot+0x4c/0x5c
[223090.262582] [<ffff0000080af3f8>] kvm_handle_guest_abort+0x240/0x774
[223090.262584] [<ffff0000080b2bac>] handle_exit+0x11c/0x1ac
[223090.262586] [<ffff0000080ab99c>] kvm_arch_vcpu_ioctl_run+0x31c/0x648
[223090.262587] [<ffff0000080a1d78>] kvm_vcpu_ioctl+0x378/0x768
[223090.262590] [<ffff00000825df5c>] do_vfs_ioctl+0x324/0x5a4
[223090.262591] [<ffff00000825e26c>] SyS_ioctl+0x90/0xa4
[223090.262595] [<ffff000008085d84>] el0_svc_naked+0x38/0x3c
This patch moves the stage2 PGD manipulation under the lock.
Reported-by: Alexander Graf <agraf@suse.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e5a672289c9754d07e1c3b33649786d3d70f5e4 upstream.
The mmu_notifier_release() callback of KVM triggers cleaning up
the stage2 page table on kvm-arm. However there could be other
notifier callbacks in parallel with the mmu_notifier_release(),
which could cause the call backs ending up in an empty stage2
page table. Make sure we check it for all the notifier callbacks.
Fixes: commit 293f29363 ("kvm-arm: Unmap shadow pagetables properly")
Reported-by: Alex Graf <agraf@suse.de>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 270c8cf1cacc69cb8d99dea812f06067a45e4609 ]
ARM has a few system calls (most notably mmap) for which the names of
the functions which are referenced in the syscall table do not match the
names of the syscall tracepoints. As a consequence of this, these
tracepoints are not made available. Implement
arch_syscall_match_sym_name to fix this and allow tracing even these
system calls.
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d4514173211586c6238629b1ef1e071927735f5 upstream.
As written in the datasheet the PCA955 can only handle low level irq and
not edge irq.
Without this fix the interrupt is not usable for pca955: the gpio-pca953x
driver already set the irq type as low level which is incompatible with
edge type, then the kernel prevents using the interrupt:
"irq: type mismatch, failed to map hwirq-18 for
/soc/internal-regs/gpio@18100!"
Fixes: 928413bd85 ("ARM: mvebu: Add Armada 388 General Purpose
Development Board support")
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3ef01c968fbfb21c2f16281445d30a865ee4412c ]
NF_CT_PROTO_DCCP/SCTP/UDPLITE were switched from tristate to boolean so
defconfig needs to be adjusted to silence warnings:
warning: symbol value 'm' invalid for NF_CT_PROTO_DCCP
warning: symbol value 'm' invalid for NF_CT_PROTO_SCTP
warning: symbol value 'm' invalid for NF_CT_PROTO_UDPLITE
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4cf48f1d7520a4d325af58eded4d8090e1b40be7 ]
Trying to initialize eMMC slot as SDIO or SD cause failure in n900 port of
qemu. eMMC itself is not detected and is not working.
Real Nokia N900 harware does not have this problem. As eMMC is really not
SDIO or SD based such change is harmless and will fix support for qemu.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a9af90a3bcde217a1c053e135f5f43e5d5fafbd upstream.
Now that explicitly executed loaders are loaded in the mmap region, we
have more freedom to decide where we position PIE binaries in the
address space to avoid possible collisions with mmap or stack regions.
4MB is chosen here mainly to have parity with x86, where this is the
traditional minimum load location, likely to avoid historically
requiring a 4MB page table entry when only a portion of the first 4MB
would be used (since the NULL address is avoided).
For ARM the position could be 0x8000, the standard ET_EXEC load address,
but that is needlessly close to the NULL address, and anyone running PIE
on 32-bit ARM will have an MMU, so the tight mapping is not needed.
Link: http://lkml.kernel.org/r/1498154792-49952-2-git-send-email-keescook@chromium.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Pratyush Anand <panand@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Daniel Micay <danielmicay@gmail.com>
Cc: Dmitry Safonov <dsafonov@virtuozzo.com>
Cc: Grzegorz Andrejczuk <grzegorz.andrejczuk@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Qualys Security Advisory <qsa@qualys.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e25ebfe56ece7541cd10a20d715cbdd148a2e06 upstream.
The pmd containing memblock_limit is cleared by prepare_page_table()
which creates the opportunity for early_alloc() to allocate unmapped
memory if memblock_limit is not pmd aligned causing a boot-time hang.
Commit 965278dcb8 ("ARM: 8356/1: mm: handle non-pmd-aligned end of RAM")
attempted to resolve this problem, but there is a path through the
adjust_lowmem_bounds() routine where if all memory regions start and
end on pmd-aligned addresses the memblock_limit will be set to
arm_lowmem_limit.
Since arm_lowmem_limit can be affected by the vmalloc early parameter,
the value of arm_lowmem_limit may not be pmd-aligned. This commit
corrects this oversight such that memblock_limit is always rounded
down to pmd-alignment.
Fixes: 965278dcb8 ("ARM: 8356/1: mm: handle non-pmd-aligned end of RAM")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c2bf9f95983fe30aa2f6463cb761cd42c2d521a upstream.
GIC_PPI flags were misconfigured for the timers, resulting in errors
like:
[ 0.000000] GIC: PPI11 is secure or misconfigured
Changing them to being edge triggered corrects the issue
Suggested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: d27509f1 ("ARM: BCM5301X: add dts files for BCM4708 SoC")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
[AmitP: Resolved minor cherry-pick conflict]
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1be7107fbe18eed3e319a6c3e83c78254b693acb upstream.
Stack guard page is a useful feature to reduce a risk of stack smashing
into a different mapping. We have been using a single page gap which
is sufficient to prevent having stack adjacent to a different mapping.
But this seems to be insufficient in the light of the stack usage in
userspace. E.g. glibc uses as large as 64kB alloca() in many commonly
used functions. Others use constructs liks gid_t buffer[NGROUPS_MAX]
which is 256kB or stack strings with MAX_ARG_STRLEN.
This will become especially dangerous for suid binaries and the default
no limit for the stack size limit because those applications can be
tricked to consume a large portion of the stack and a single glibc call
could jump over the guard page. These attacks are not theoretical,
unfortunatelly.
Make those attacks less probable by increasing the stack guard gap
to 1MB (on systems with 4k pages; but make it depend on the page size
because systems with larger base pages might cap stack allocations in
the PAGE_SIZE units) which should cover larger alloca() and VLA stack
allocations. It is obviously not a full fix because the problem is
somehow inherent, but it should reduce attack space a lot.
One could argue that the gap size should be configurable from userspace,
but that can be done later when somebody finds that the new 1MB is wrong
for some special case applications. For now, add a kernel command line
option (stack_guard_gap) to specify the stack gap size (in page units).
Implementation wise, first delete all the old code for stack guard page:
because although we could get away with accounting one extra page in a
stack vma, accounting a larger gap can break userspace - case in point,
a program run with "ulimit -S -v 20000" failed when the 1MB gap was
counted for RLIMIT_AS; similar problems could come with RLIMIT_MLOCK
and strict non-overcommit mode.
Instead of keeping gap inside the stack vma, maintain the stack guard
gap as a gap between vmas: using vm_start_gap() in place of vm_start
(or vm_end_gap() in place of vm_end if VM_GROWSUP) in just those few
places which need to respect the gap - mainly arch_get_unmapped_area(),
and and the vma tree's subtree_gap support for that.
Original-patch-by: Oleg Nesterov <oleg@redhat.com>
Original-patch-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Tested-by: Helge Deller <deller@gmx.de> # parisc
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[wt: backport to 4.11: adjust context]
[wt: backport to 4.9: adjust context ; kernel doc was not in admin-guide]
[wt: backport to 4.4: adjust context ; drop ppc hugetlb_radix changes]
Signed-off-by: Willy Tarreau <w@1wt.eu>
[gkh: minor build fixes for 4.4]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46350b71a09ccf3573649e03db55d4b61d5da231 upstream.
Table 8 from MX6DL datasheet (IMX6SDLCEC Rev. 5, 06/2015):
http://cache.nxp.com/files/32bit/doc/data_sheet/IMX6SDLCEC.pdf
states the following:
"LDO Output Set Point (VDD_ARM_CAP) = 1.125 V minimum for operation
up to 396 MHz."
So fix the entry by adding the 25mV margin value as done in the other
entries of the table, which results in 1.15V for 396MHz operation.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Cc: Stephane Fillod <f8cfe@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33b5c38852b29736f3b472dd095c9a18ec22746f upstream.
We currently have the HSCTLR.A bit set, trapping unaligned accesses
at HYP, but we're not really prepared to deal with it.
Since the rest of the kernel is pretty happy about that, let's follow
its example and set HSCTLR.A to zero. Modern CPUs don't really care.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3df1ec06353e51fc44563d2e7e18d42811af290 upstream.
Remove ADC channels that are not available by default on the sama5d3_xplained
board (resistor not populated) in order to not create confusion.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9cdd31e5913c1f86dce7e201b086155b3f24896b upstream.
The voltage reference for the ADC is not 3V but 3.3V since it is connected to
VDDANA.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
